INTERNATIONAL ISO

STANDARD 8676

Second edition
1999-08-15

Hexagon head screws with metric fine pitch

thread — Product grades A and B
Vis à tête hexagonale à filetage métrique à pas fin entièrement filetées —
Grades A et B

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999

A Reference number
ISO 8676:1999(E)
ISO 8676:1999(E)

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.

Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

International Standard ISO 8676 was prepared by Technical Committee ISO/TC 2, Fasteners.

This second edition cancels and replaces the first edition (ISO 8676:1988) which has been technically revised.

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999

© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [email protected]
Printed in Switzerland

ii
© ISO ISO 8676:1999(E)

Introduction

This International Standard is part of the complete ISO product standard series on external hexagon drive
fasteners. The series comprises:

a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);

b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);

c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);

d) hexagon bolts with flange (ISO 4162 and ISO 15071);

e) hexagon nuts with flange (ISO 4161 and ISO 10663);

f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999

iii
 iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999
INTERNATIONAL STANDARD © ISO ISO 8676:1999(E)

Hexagon head screws with metric fine pitch thread —

Product grades A and B

1 Scope

This International Standard specifies the characterisitics of hexagon head screws with metric fine pitch thread with
nominal thread diameters d from 8 mm to 64 mm of product grade A for nominal thread diameters d from 8 mm to
24 mm and nominal lengths, l, up to and including 10d or 150 mm, whichever is shorter, and of product grade B for
nominal thread diameters d over 24 mm or nominal lengths, l, over 10d or 150 mm, whichever is shorter.

If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1,
ISO 4753 and ISO 4759-1.

Coarse thread screws according to ISO 4017 should be first choice.

2 Normative references
iTeh STANDARD PREVIEW
(standards.iteh.ai)
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, ISO subsequent
8676:1999 amendments to, or revisions of, any of these
publications do not apply. https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
521705ab4b28/iso-8676-1999
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.

ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.

ISO 724:1993, ISO general-purpose metric screw threads — Basic dimensions.

ISO 888:1976, Bolts, screw and studs — Nominal lengths, and thread lengths for general purpose bolts.

ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts screws
and studs.

ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.

ISO 3269:—1), Fasteners — Acceptance inspection.

ISO 3506-1:1997, Mechanical properties of corrosion-resistant stainless-steel fasteners — Part 1: Bolts screws and
studs.

ISO 4042:1999, Fasteners — Electroplated coatings.

ISO 4753:—2), Fasteners — Ends of parts with external metric ISO thread.

1) To be published. (Revision of ISO 3269:1988)

2) To be published. (Revision of ISO 4753:1983)

1
ISO 8676:1999(E) © ISO

ISO 4759-1:—3), Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C.

ISO 6157-1:1988, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements.

ISO 8839:1986, Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals.

ISO 8992:1986, Fasteners — General requirements for bolts, screws, studs and nuts.

ISO 10683:—4), Fasteners — Non-electrolytically applied zinc flake coatings.

3 Dimensions

See Figure 1 and Tables 1 and 2

Symbols and descriptions of dimensions are defined in ISO 225.

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999

3) To be published. (Revision of ISO 4759-1:1978)

4) To be published.

2
© ISO ISO 8676:1999(E)

Dimensions in millimetres

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
a https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
␤ = 15∞ to 30∞
b
521705ab4b28/iso-8676-1999
Point shall be chamfered (see ISO 4753)
c Incomplete thread u ⭐ 2P
d Reference datum for dw
e ds ⬇ pitch diameter

Figure 1

3
ISO 8676:1999(E) © ISO

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999

4
© ISO ISO 8676:1999(E)

iTeh STANDARD PREVIEW

(standards.iteh.ai)
ISO 8676:1999
https://standards.iteh.ai/catalog/standards/sist/edfc571e-194f-43d7-b01f-
521705ab4b28/iso-8676-1999