Project:

Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Project data
Project name
Project number
CHANGE ROOM & POOL STORAGE- Z8
Author
AHMED EZZAT
Description DETAIL A
Date 1/24/2024
Design code AISC 360-10

Material
Steel S355
Concrete C32/40

1 / 12
Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Project item DETAIL A

Design
Name DETAIL A
Description EMBEDDED CONNECTIONS
Analysis Stress, strain/ loads in equilibrium
Design code AISC - LRFD 2010

Beams and columns

β – Direction γ - Pitch α - Rotation Offset ex Offset ey Offset ez
Name Cross-section Forces in
[°] [°] [°] [mm] [mm] [mm]
SC 01 8 - SHS200/200/10.0 0.0 -90.0 0.0 0 0 0 Node

2 / 12
Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

3 / 12
Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Cross-sections
Name Material
8 - SHS200/200/10.0 S355

Cross-sections
Name Material Drawing

8 - SHS200/200/10.0 S355

Anchors
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
20 A325M 20 A325M 20 830.0 314

4 / 12
Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Load effects (forces in equilibrium)

N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
IFC01 SC 01 -80.0 30.0 20.0 0.0 0.0 0.0
IFC02 SC 01 60.0 30.0 20.0 0.0 0.0 0.0

Foundation block
Item Value Unit
CB 1
Dimensions 450 x 450 mm
Depth 925 mm
Anchor 20 A325M
Anchoring length 250 mm
Shear force transfer Anchors
Mortar joint 25 mm

Check

Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Anchors 14.4 < 100% OK
Welds 53.6 < 100% OK
Concrete block 2.7 < 100% OK
Buckling 134.47

Plates
fy Thickness σEd εPl σcEd
Name Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
SC 01 355.0 10.0 IFC02 70.3 0.0 0.0 OK
BP1 355.0 25.0 IFC02 45.6 0.0 0.0 OK

Design data
fy εlim
Material
[MPa] [%]
S355 355.0 5.0

Symbol explanation
εPl Plastic strain
σcEd Contact stress
σEd Eq. stress
fy Yield strength
εlim Limit of plastic strain

5 / 12
 Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Strain check, IFC02

Equivalent stress, IFC02

6 / 12
 Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Anchors
Nf V ϕNp ϕNsb Utt Uts Utts
Shape Item Loads Status
[kN] [kN] [kN] [kN] [%] [%] [%]
A1 IFC01 0.0 9.1 588.8 - 0.0 14.4 3.9 OK

A2 IFC02 16.3 9.0 588.8 128.2 11.5 14.2 6.6 OK

A3 IFC01 0.0 9.0 588.8 - 0.0 14.2 3.8 OK

A4 IFC02 16.3 9.2 588.8 128.2 11.4 14.4 6.7 OK

Design data
ϕNsa ϕVsa
[kN] [kN]
142.3 63.4

Symbol explanation
Nf Tension force
V Resultant of shear forces Vy, Vz in bolt
ϕNp Pullout strength in tension – ACI 318-14 – 17.4.3
ϕNsb Concrete side-face blowout strength in tension – ACI 318-14 – 17.4.4
Utt Utilization in tension
Uts Utilization in shear
Utts Utilization in tension and shear
ϕNsa Steel strength of anchor in tension - ACI 318-14 – 17.4.1
ϕVsa Steel strength of anchor in shear - ACI 318-14 – 17.5.1

Detailed result for A4

Anchor tensile resistance (ACI 318-14 – 17.4.1)

ϕNsa = ϕ ⋅ Ase,N ⋅ futa =

​ ​ ​
142.3 kN ≥ Nf =
​
16.3 kN

Where:
ϕ = 0.70 – resistance factor
Ase,N = 245 mm2 – tensile stress area
​

futa = 830.0 MPa – specified tensile strength of anchor steel:

​

futa = min(860 MPa, 1.9 ⋅ fya , fu ) , where:

​ ​ ​

fya = 660.0 MPa – specified yield strength of anchor steel

​

fu = 830.0 MPa – specified ultimate strength of anchor steel

​

7 / 12
 Project:
Project no: CHANGE ROOM & POOL STORAGE- Z8
Author: AHMED EZZAT

Concrete pullout resistance (ACI 318-14 – 17.4.3)

ϕNpn = ϕ ⋅ Ψc,P ⋅ Np =
​ ​ ​
588.8 kN ≥ Nf = ​
16.3 kN

Where:
ϕ = 0.70 – resistance factor
Ψc,P = 1.00 ​
– modification factor for concrete condition

Np = 841.2 kN – basic concrete pullout strength for headed anchor:

​

Npr = 8 ⋅ Abrg ⋅ fc′ , where:

​ ​ ​

Abrg = 3286 mm2 – bearing area of the head of stud or anchor bolt
​

fc′ = 32.0 MPa – concrete compressive strength

​

Concrete sideface blowout resistance (ACI 318-14 – 17.4.4)

ϕNsb = rc ⋅ Nsbg =
​ ​
128.2 kN ≥ Nf = ​
16.3 kN

Where:
rc = 0.50 – reduction factor for anchor close to an edge or multiple anchors with small spacing:
​

ca2
1+
​

rc = min( 4ca1 , 1 + 6⋅csa1 ), 0.5 ≤ rc ≤ 1 , where:

​

​ ​ ​ ​

ca1 = 85 mm – shorter distance from an anchor to an edge

​

ca2 = 85 mm – longer distance from an anchor to an edge

​

s = 280 mm – spacing between anchors

Nsbg = 256.3 kN – concrete side-face blowout strength of headed anchor in tension:

​

Nsb = ϕ ⋅ 13.0 ⋅ ca1 ⋅ Abgr ⋅ fc′ , where:

​ ​ ​​ ​ ​

Abgr = 3286 mm2 – bearing area of the head of stud or anchor bolt
​

fc′ = 32.0 MPa – concrete compressive strength

​

ϕ = 0.70 – resistance factor

Shear resistance (ACI 318-14 – 17.5.1)

ϕVsa = rm ⋅ ϕ ⋅ 0.6 ⋅ Ase,V ⋅ futa =

​ ​ ​ ​
63.4 kN ≥ V = 9.2 kN

Where:
rm = 0.8
​ – reduction factor for steel strength in shear in case of mortar joint
ϕ = 0.65 – resistance factor
Ase,V = 245 mm2 – tensile stress area
​

futa = 830.0 MPa – specified tensile strength of anchor steel:

​

futa = min(860 MPa, 1.9 ⋅ fya , fu ) , where:

​ ​ ​

fya = 660.0 MPa – specified yield strength of anchor steel

​

fu = 830.0 MPa – specified ultimate strength of anchor steel

​

8 / 12
 Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT
Interaction of tensile and shear forces (ACI 318-14 – R17.6)

Utt 5/3 + Uts 5/3 =

​ ​ 0.07 ≤ 1.0

Where:
Utt = 0.11 – maximum ratio of factored tensile force and tensile resistance determined from all appropriate failure
​

modes
Uts = 0.14 – maximum ratio of factored shear force and shear resistance determined from all appropriate failure
​

modes

Supplementary reinforcement (ACI 318-14 – 17.4.2.9; ACI 318-14 – 17.5.2.9)

Supplementary reinforcement should resist force of 65.5 kN in tension and 36.1 kN in shear.

Weld sections
Th Ls L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
BP1 SC 01 E70xx ◢4.2 ◢6.0 721 10 IFC02 7.0 13.0 53.6 OK

Symbol explanation
Th Throat thickness of weld
Ls Leg size of weld
L Length of weld
Lc Length of weld critical element
Fn Force in weld critical element
ϕRn Weld resistance AISC 360-16 J2.4
Ut Utilization

Detailed result for BP1 / SC 01

Weld resistance check (AISC 360-10: J2-4)

ϕRn = ϕ ⋅ Fnw ⋅ Awe =

​ ​ ​
13.0 kN ≥ Fn =
​
7.0 kN

Where:
Fnw = 394.7 MPa – nominal stress of weld material:
​

Fnw = 0.6 ⋅ FEXX ⋅ (1 + 0.5 ⋅ sin1.5 θ) , where:

​ ​

FEXX = 482.6 MPa – electrode classification number, i.e. minimum specified tensile strength
​

θ = 53.9° – angle of loading measured from the weld longitudinal axis

Awe = 44 mm2 – effective area of weld critical element

​

ϕ = 0.75 – resistance factor for welded connections

Concrete block
A1 A2 σ Ut
Item Loads Status
[mm2] [mm2] [MPa] [%]
CB 1 IFC01 146338 187757 0.5 2.7 OK

9 / 12
 Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Symbol explanation
A1 Loaded area
A2 Supporting area
σ Average stress in concrete
Ut Utilization

Detailed result for CB 1

Concrete block compressive resistance check (AISC 360-10 Section J8)

ϕc fp,max =
​ ​
20.0 MPa ≥ σ= 0.5 MPa

Where:
fp,max = 30.8 MPa – concrete block design bearing strength:
​

fp,max = 0.85 ⋅ fc′ ⋅

​ ​
A2
A1
​

​
​ ​ ≤ 1.7 ⋅ fc′ , where:
​

fc′
= 32.0 MPa – concrete compressive strength
​

A1 = 146338 mm2 – base plate area in contact with concrete surface

​

A2 = 187757 mm2 – concrete supporting surface

​

ϕc = 0.65 – resistance factor for concrete

​

Buckling
Factor
Loads Shape
[-]
IFC01 1 134.47
2 143.11
3 186.00
4 199.09
5 214.74
6 259.91
IFC02 1 454.86
2 504.06
3 610.73
4 641.75
5 926.26
6 984.75

10 / 12
Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Bill of material

Manufacturing operations
Plates Welds Length
Name Shape Nr. Bolts Nr.
[mm] [mm] [mm]

BP1 P25.0x400.0-400.0 (S355) 1 Fillet: a = 4.2 724.2 20 A325M 4

Welds
Throat thickness Leg size Length
Type Material
[mm] [mm] [mm]
Fillet E70xx 4.2 6.0 724.2

Anchors
Length Drill length
Name Count
[mm] [mm]
20 A325M 300 250 4

Drawing

BP1

P25.0x400-400 (S355)

11 / 12
Project:
Project no:
CHANGE ROOM & POOL STORAGE- Z8
Author:
AHMED EZZAT

Code settings
Item Value Unit Reference
Friction coefficient - concrete 0.40 - ACI 349 – B.6.1.4
Friction coefficient in slip-resistance 0.30 - AISC 360-10 J3.8
Limit plastic strain 0.05 -
Plastic
Weld stress evaluation
redistribution
Detailing No
Distance between bolts [d] 2.66 - AISC 360-10 – J3.3
Distance between bolts and edge [d] 1.25 - AISC 360-10 – J.3.4
Concrete breakout resistance check None
Base metal capacity check at weld fusion
No AISC 360-10: J2-2
face
Cracked concrete Yes ACI 318-14 – Chapter 17
Local deformation check No
Local deformation limit 0.03 - CIDECT DG 1, 3 - 1.1
Analysis with large deformations for hollow section
Geometrical nonlinearity (GMNA) Yes
joints

12 / 12