Data Sheet

V 1.1 / Feb. 2015

MSM261S4030H0
I2S digital output MEMS microphone with Multi‐modes
 MSM261S4030H0
I2S digital output MEMS microphone

GENERAL DESCRIPTION APPLICATIONS

MSM26S4030H0 is an omnidirectional, — Mobile Phone

bottom‐ported, I2S digital output MEMS — Laptop
microphone. It has high performance and
— Tablet computer
reliability.
— Bluetooth headset
MSM26S4030H0 is available in a 4 mm × — Earphone
3 mm × 1.0 mm metal cap LGA package. It is — Wearable intelligent equipment
SMT compatible with no sensitivity
degradation.

FEATURES PRODUCT VIEW

— Cost effective
— Low Power mode
— Digital I2S output
— Compatible with Sn/Pb and Pb‐free
solder processes
— RoHS/Halogen free compliant
— Sensitivity Matching within +/‐1dB

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 2
 MSM261S4030H0
I2S digital output MEMS microphone

ABSOLUTE MAXIMUM RATINGS

Parameter Maximum value Unit

Supply Voltage −0.3 to 4.0 V
Sound Pressure Level 140 dB SPL
Mechanical Shock 10,000 g
Temperature Range −40 to 100 °C
Electrostatic discharge protection 2 (HBM) kV

SPECIFICATIONS

All data taken at 25°C, Relative Humidity 45±5% L/R pin grounded unless otherwise specified
Vdd=1.8V, clock frequency=3.072MHz
Limits unit condition
Min. Nom. Max.
Directivity Omni directional
Sensitivity ‐27 ‐26 ‐25 dB dBFS @1kHz 1Pa

Operation voltage 1.6 3.6 V

Freq. range Refer to the frequency response Hz
Sensitivity loss across
No change across the voltage range dB
supply voltage
20 kHz bandwidth,
Signal to noise ratio ‐ 57 ‐ dB
A‐weighted
‐ ‐ 1% 100dB SPL @1kHz
THD
‐ ‐ 10% 120dB SPL @1kHz
PSR ‐72 dBFS(A)
‐ 750 1000 μA Normal mode
Current consumption
‐ 400 ‐ μA Low power mode
1.0 3 4.0 MHz Normal mode
Clock frequency
150 ‐ 600 KHz Low power mode
Operating temperature ‐40 ‐ 100 °C
Storage temperature ‐40 ‐ 100 °C

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 3
 MSM261S4030H0
I2S digital output MEMS microphone

TYPICAL FREQUENCY RESPONSE

Frequency Response @94dB SPL

20
Sensitivity (dB FS/Pa)

10

‐10

‐20
100 200 500 1K 2K 5K 10K
Frequence (Hz)

LOGIC TABLE

Parameter Symbol Min Max Unit

Low Voltage Input(L/R,
Digital VIL 0 0.25 × VDD V
WS, SCK)
High Voltage
Input VIH 0.7 × VDD VDD V
Input(L/R, WS, SCK)
Voltage Output Low VOL 0.1 × VDD V
Voltage Output Low VOL 0.3 × VDD V
SD Voltage Output High VOH 0.7 × VDD V
Voltage Output High VOH 0.9 × VDD V
Digital
Voltage Output Low VOL 0.1 × VDD V
Output Voltage Output Low VOL 0.3 × VDD V
Voltage Output High VOH 0.7 × VDD V
Voltage Output High VOH 0.9 × VDD V

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 4
 MSM261S4030H0
I2S digital output MEMS microphone

TIMING DIAGRAM

Parameter Description Min. Norm. Max. Unit

tSCH SCK High — 50 — ns
tSCL SCK Low — 50 — ns
tSCP SCK Period — 325 — ns
fSCK SCK Frequency — 3.072 — MHz
tWSS WS Setup — 0 — ns
tWSH WS Hold — 20 — ns
fWS WS Frequency — 7.8 — kHz

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 5
 MSM261S4030H0
I2S digital output MEMS microphone

SMT Parameters：

1. Recommend PCB land pattern layout and stencil pattern：（unit: mm）

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 6
 MSM261S4030H0
I2S digital output MEMS microphone

2. Recommend reflow profile:

Description Parameter Pb free

Average ramp rate TL to TP 3 °C/sec max
Preheat
Minimum temperature TSMIN 150 °C
Maximum temperature TSMAX 200 °C
Time(TSMIN to TSMAX) tS 60 sec to 120 sec
Ramp‐up rate TSMAX to TL 1.25 °C/sec
Time maintained above liquidous temperature tL 60 sec to 150 sec
Liquidous temperature TL 217 °C
Peak temperature TP 260 °C
Time within 5°C of actual peak temperature tP 20 sec to 40 sec
Ramp‐down rate TP to T smax 6 °C/sec max
Time 25 °C (t25 °C) to peak temperature t 8 minutes max

3. note：

When washing the PCB, ensure that water does not make contact with the microphone port.
Do not use blow‐off procedures or ultrasonic cleaning.

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 7
 MSM261S4030H0
I2S digital output MEMS microphone

OUTLINE DIMENSIONS AND PIN DEFINITION：

4 5
Port
3 6

2 7

1 8
1

TOP VIEW SIDE VIEW BOTTOM VIEW

1 GND Ground Connect to ground on the PCB.

2 N/C — Do not connect
3 WS Input Serial Data‐Word Select for I²S Interface.
Microphone Enable. When set low (ground), the microphone is disabled and put in
4 CHIPEN Input
power‐down mode. When set high (VDD), the microphone is enabled.
Left/Right Channel Select. When set low, the microphone outputs its signal in the left channel
5 L/R Input
of the I²S frame; when set high, the microphone outputs its signal in the right channel.
6 SCK Input Serial Data Clock for I²S Interface.
Serial Data Output for I²S Interface. This pin tristates when not actively driving the appropriate
7 SD Output output channel. The SD trace should have a 100 kΩ pull‐down resistor to discharge the line
during the time that all microphones on the bus have tristated their outputs.
8 VDD Power 1.8 to 3.3 V. This pin should be decoupled to Pin 6 with a 0.1 μF capacitor.

Item Dimension Tolerance

Length (L) 4.0 ±0.10
Width (W) 3.0 ±0.10
Height (H) 1.05 ±0.10
Acoustic Port (AP) Ø0.65 ±0.10
Dimensions are in millimeters
Tolerance is ±0.1mm unless otherwise specified.

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 8
 MSM261S4030H0
I2S digital output MEMS microphone

PACKAGING & MARKING DETAIL：

Note: Dimensions are in mm.

Model Number Reel Diameter Quantity Per Reel

MSM26S4030H0 13 inch 5000

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 9
 MSM261S4030H0
I2S digital output MEMS microphone

RECOMMENDED INTERFACE CIRCUIT：

FROM VOLTAGE SYSTEM MASTER FROMVOLTAGE

REGULATOR (DSP , MCU , Codec) REGULATOR
(1.8VTO 3.3V) (1.8V TO 3.3V)

SCK

WS

SD
0.1F 0.1F

VDD VDD
VDD VDD

CHIPEN SCK SCK CHIPEN

WS WS
L/R SD SD L/R
LEFT RIGHT
100kΩ

GND GND GND GNDGNDGND

Stereo Output I2S Format

Mono Output I2S Format Left Channel ( L/R = 0)

Mono Output I2SFormat Right Channel ( L /R = 1)

I²S DATA INTERFACE

The serial data is in slave mode I²S format, which has 24‐bit depth in a 32 bit word. In a
stereo frame there are 64 SCK cycles, or 32 SCK cycles per data‐word. When L/R=0, the output
data in the left channel, while L/R=Vdd, data in the right channel. The output data pin (SD) is
tristated after the LSB is output so that another microphone can drive the common data line.
Data Word Length
The output data‐word length is 24 bits per channel. The Mic must always have 64 clock
cycles for every stereo data‐word (fSCK = 64 × fWS).
Data‐Word Format
The default data format is I²S, MSB‐first. In this format, the MSB of each word is delayed by
one SCK cycle from the start of each half‐frame.

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 10
 MSM261S4030H0
I2S digital output MEMS microphone

REVISION HISTORY:

Revision Subjects (major changes since last revision) Date

1.0 Initial release 2015‐1
1.1 Modified the outline dimension 2015‐02‐12

公司销售、技术支持联系方式 (http://www.memsensing.com)
For English: 中文用户：
MEMSensing Microsystems Co. Ltd. 苏州敏芯微电子技术有限公司
No. 99 Jinji Lake Avenue, Bldg. NW‐09, Suite 501 苏州工业园区金鸡湖大道 99 号，NW‐09 楼，501 室
Suzhou Industrial Park, China 215123 中国 215123
Phone: +86 512 62956055 电话: +86 512 62956055
Fax: +86 512 62956056 传真: +86 512 62956056
Disclaimer: specifications and characteristics are subject to change without notice. MEMSensing
Microsystems Co. Ltd. assumes no liability to any customer, licensee or any third party for any
damages or any kind of nature whatsoever related to using this technical data.

© 2011‐2015 MEMSensing Microsystems Co. Ltd, —DOC NO:DS‐035, P ENG, All rights reserved 11