VEC012POB_ManualEN_042506 5/19/06 4:14 PM Page 8

VEC012POB

TWO YEAR LIMITED WARRANTY PROGRAM

This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Power On Board regarding this product. There is no other warranty, other than those
described herein. Any implied warranty of merchantability or fitness for a particular purpose on this
product is limited in duration to the duration of this warranty.
This Power On Board product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for two years from the date of purchase without additional charge. The
warranty does not extend to subsequent purchasers or users. Manufacturer will not be responsible for
any amount of damage in excess of the retail purchase price of the product under any circumstances.
Jump-Start System
Incidental and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to damage to units from
12 Volt DC Power Supply
misuse or incorrect installation/connection. Misuse includes wiring or connecting to improper polarity
power sources.
RETURN/REPAIR POLICY: Defective products may be returned to manufacturer. Any defective product
that is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge.
If such a product is returned more than 30 days but less than two years from the purchase date,
manufacturer will repair the unit or, at its option, replace it, free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at manufacturer’s option.
A unit may be replaced with a new or reconditioned unit of the same or comparable design. The
repaired or replaced unit will then be warranted under the terms of the remainder of the warranty
period. The customer is responsible for the shipping charges on all returned items. During the warranty
period, manufacturer will be responsible for the return shipping charges to the customer in the United
States.
LIMITATIONS: This warranty does not cover accessories, such as charging adapters, bulbs, fuses and
batteries, damage or defects resulting from normal wear and tear (including chips, scratches, abrasions,
discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our
service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow
instructions for care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department toll free at (866)
584-5504 for general repair information and charges if applicable. You may also contact us through
our website at www.vectormfg.com.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser
specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Technical Support by telephone, fax
or mail (see below). We suggest that you keep the original packaging in case you need to ship the unit.
When returning a product, include your name, address, phone number, dated sales receipt (or copy)
and a description of the reason for return and product serial number. After repairing or replacing the
unit, we will make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Power On Board.
Enter “VEC012POB” as Model and “Jump-Start System” as Product Type. All Vector products must be
registered within 30 days of purchase to activate this warranty. Mail the completed registration form,
along with a copy of the original sales receipt, to:

USER’S MANUAL
& WARRANTY INFORMATION
ATTN.: CUSTOMER SERVICE
4140 SW 30th Ave., Ft. Lauderdale, FL 33312
• TOLL FREE: (866) 584-5504 • FAX: (954) 584-5556 • IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND

WARRANTY IS NON-TRANSFERABLE.
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
BD051906
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
© 2006 VECTOR PRODUCTS, INC. Toll Free: (866) 584-5504
MADE IN CHINA

8
www.vectormfg.com
VEC012POB_ManualEN_042506 5/19/06 4:14 PM Page ii

IMPORTANT SAFETY INSTRUCTIONS Inflator Safety

1. Never attempt to disable or block the inflation and deflation ports while pump is operating.
WARNINGS
2. Never cover unit at any time.
1. RISK OF EXPLOSIVE GAS MIXTURES — WORKING IN THE VICINITY OF A LEAD-ACID
3. Never leave the pump unattended while in use.
BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE 4. Never allow sand, small rocks or other debris to be sucked into the inflation or deflation ports.
THAT EACH TIME BEFORE USING THIS UNIT, YOU READ THIS MANUAL AND FOLLOW 5. RISK OF INJURY: Never look into or point the inflator port opening toward anyone’s eyes. Do not
THE INSTRUCTIONS EXACTLY. direct air stream at body.
2. To reduce risk of battery explosion, follow these instructions and those published by 6. Do not use the compressor continuously for longer than 15 minutes. Extended use will cause it to
the battery manufacturer and manufacturer of any equipment you intend to use in overheat and can damage the product. After 15 minutes of continuous use, turn the unit OFF and
vicinity of battery. Review cautionary markings on these products and on engine. wait 15 minutes before resuming operation of the compressor.
3. This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. 7. DO NOT overinflate objects or exceed manufacturer’s recommendations for pressure on objects to
Therefore, if used in a garage or enclosed area, the unit MUST be placed not less be inflated.
than 18 inches above the floor.
4. TO REDUCE THE RISK OF ELECTRIC SHOCK, do not expose this unit to rain. Store Personal Safety
indoors. FIRST AID
Battery Safety SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with
soap and water. If redness, pain or irritation occurs, seek immediate medical attention.
1. When working with lead acid batteries, always make sure immediate assistance is available in
case of accident or emergency. EYES: If battery acid comes in contact with eyes, flush eyes immediately for a minimum of 15 minutes
2. Always use protective eyewear when using this product: contact with battery acid may cause and seek immediate medical attention.
blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with
CAUTIONS
battery acid.
• All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure
3. There is a risk of releasing explosive gases when lead acid batteries are charged or discharged. all switches are in the OFF position before connection to a power source or load.
Failure to follow instructions may cause property damage and/or personal injury. • Never insert anything other than the supplied power/recharging cords or recommended appliance
4. When connecting the battery clamps to a discharged battery and an alarm sounds — the clamp power/recharging cords into the 12 volt DC charging/power outlet on this unit. Do not use any
connections are incorrect and need to be reversed. accessory that is not recommended or provided by the manufacturer.
5. Jump-start procedures should only be performed in a safe, dry, well-ventilated area. • Do not use this unit to operate appliances that need more than 5 amps to operate from the 12 volt DC
6. Always store battery clamps on the clamp tabs on the back of the unit when not in use. Never touch accessory outlet.
battery clamps together. This can cause dangerous sparks, power arcing and/or explosion. • This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect
7. When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, to a 6 volt or 24 volt battery system.
and be sure to keep all clamps, cords, clothing and body parts away from moving vehicle parts. • This system is not designed to be used as a replacement for a vehicle battery. Do not attempt to operate
a vehicle that does not have a battery installed.
8. Do not wear vinyl clothing when jump-starting a vehicle, friction can cause dangerous static-
• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the
electrical sparks. Remove all jewelry or metal objects that could cause short circuits or react with recommended number of attempts, discontinue jump-start procedures and look for other problems that
battery acid. may need to be corrected.
9. Never allow RED and BLACK clamps to touch each other or another common metal conductor — • Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during
this could cause damage to the unit and/or create a sparking/explosion hazard. storage, use and recharging. To avoid possible damage that may shorten the unit’s working life, protect
10. a. For negative-grounded systems (most common), connect the POSITIVE (RED) clamp to the it from direct sunlight, direct heat and/or moisture.
POSITIVE ungrounded battery post and the NEGATIVE (BLACK) clamp to the vehicle chassis or • Check unit periodically for wear and tear. Contact the Customer Service Department at
engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or (800) 618-5178 to replace worn or defective parts.
sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. • Do not drop this unit as it may damage the product. If unit is dropped or damaged, please discontinue
b. For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the NEGATIVE using it.
ungrounded battery post and the POSITIVE (RED) clamp to the vehicle chassis or engine block • Never submerge this unit in water.
away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body • Store indoors. Do not operate unit in rain or snow, or use when wet.
parts. Connect to a heavy gauge metal part of the frame or engine block. • Do not operate this unit in a closed area or restrict ventilation in any way.
11. Always disconnect the NEGATIVE (BLACK) jumper cable first, followed by the POSITIVE (RED) THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS.
jumper cable, except for positive grounded systems.
12. Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, Read This User’s Manual Before Using This Unit.
protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in
injury or fire).
13. Do not smoke or use flammable items (matches, cigarette lighters, etc.) while working on a vehicle’s
SAVE THESE INSTRUCTIONS
battery system.
14. DO NOT ATTEMPT TO JUMP-START A FROZEN BATTERY.
15. Place this unit as far away from the battery as DC cables permit.
16. Never allow battery acid to come in contact with this unit.
17. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-
started. Before jump-starting, read the vehicle’s owners manual to confirm that external-starting
assistance is suitable.
VEC012POB_ManualEN_042506 5/19/06 4:14 PM Page iv

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Control and Function Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Using the Jump-Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Using the 12 Volt DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the Emergency Area Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the Portable Inflator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Inflating Tires or Products With Valve Stems . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Inflating Other Inflatables Without Valve Stems . . . . . . . . . . . . . . . . . . . . . . . . 5
Using the USB Power Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Charging/Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INTRODUCTION
Thank you for choosing the Power On Board Jump-Start System. Please
read this guide carefully before use to ensure optimum performance and avoid
damage to the unit or items that you are using it with.

FEATURES
• Keyless ON/OFF Safety Power Switch
• Built-in non-spillable, maintenance-free, heavy duty, AGM, 19 amp/hour, sealed,
lead-acid battery
• 450 instantaneous cranking amps
• Heavy duty #4AWG jumper cables and 450 amp copper clamps, with
exclusive recessed storage channels
• Audible reverse polarity alarm
• Long-life, ultra bright LED Emergency Area Light
• USB Charging Port charges and recharges personal electronics
• 12 Volt DC Accessory Outlet charges and rechages DC appliances
• Easy-to-read LED battery charge status indicators
• Cordless/rechargeable, includes AC and DC charging adapters
• 120 volt AC charger is Underwriter Laboratories safety tested and listed
• Built-in portable inflator for vehicle tires, trailer tires and recreational inflatables,
with lighted analog gauge
• Requires no maintenance (other than recharging) for optimum operation

1
VEC012POB_ManualEN_042506 5/19/06 4:14 PM Page 2

Control and Function Guide 1. Turn OFF vehicle ignition and all accessories (radio, A/C, lights, connected cell
phone chargers, etc.). Place vehicle in “park” and set the emergency brake.
4 5 6 2. Make sure the Jump-Starter Power Switch is turned to OFF.
12
3 7 3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then
11
2
the black clamp.
8
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative
battery terminal is connected to chassis) (MOST COMMON)
9 4a. Connect POSITIVE (+) RED clamp to vehicle battery’s POSITIVE terminal.
4b. Connect NEGATIVE (–) BLACK clamp to chassis or a solid, non-moving,
metal vehicle component or body part. NEVER CLAMP DIRECTLY TO
10
NEGATIVE BATTERY TERMINAL OR MOVING PART.
1 5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
16 13
Note: In the rare event that the vehicle to be started has a POSITIVE GROUNDED
SYSTEM (positive battery terminal is connected to chassis), replace steps 4a
and 4b above with steps 5a and 5b, then proceed to step 6.
5a. Connect NEGATIVE (–) BLACK clamp to vehicle battery’s NEGATIVE terminal.
14
5b. Connect POSITIVE (+) RED CLAMP to vehicle chassis or a solid, non-
15
moving, metal vehicle component or body part. NEVER CLAMP DIRECTLY
TO POSITIVE BATTERY TERMINAL OR MOVING PART.
6. When clamps are connected properly, turn the Jump-Starter Power Switch to ON.
Front View Back View
7. Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts.
1. Built-in LED Emergency Area Light 9. USB Power Port
8. Turn the Jump-Starter Power Switch back to the OFF position.
2. AC Recharge Port 10. Area Light Power Switch
9. Disconnect the NEGATIVE (–) engine or chassis clamp first, then disconnect the
3. 12 Volt DC Outlet 11. Pressure Gauge
POSITIVE (+) battery clamp.
4. Battery Charge Level Pushbutton 12. Inflator Power Switch
FOLLOW ALL “IMPORTANT SAFETY INSTRUCTIONS” FOUND AT THE
5. LED Battery Status Indicators 13. POSITIVE (+) RED Clamp BEGINNING OF THIS USER’S MANUAL.
6. Jump-Starter Power Switch 14. Air Hose
7. Reverse Polarity Indicator 15. Connector (Chuck) WARNINGS
• Jump-Starter Power Switch should be OFF prior to jump-starting.
8. USB Power Port Power Switch 16. NEGATIVE (–) BLACK Clamp
• This power system is to be used ONLY on vehicles or boats with
12 volt DC battery systems.
• Never touch RED and BLACK clamps together — this can cause
dangerous sparks, power arcing, and/or explosion.
• Vehicles that have on-board computerized systems may be
damaged if vehicle battery is jump-started. Before jump-starting this
DC/DC AC/DC type of vehicle, read the vehicle manual to confirm that external-
CHARGER/ADAPTER CHARGER/ADAPTER starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If
the engine fails to start after the recommended number of attempts,
USING THE JUMP-STARTER discontinue jump-start procedure and look for other problems that
This unit is delivered in a partially charged state – you must fully need to be corrected.
charge it before using it for the first time. Initial AC charge should be • After use, turn the Jump-Starter Power Switch OFF.
for 48 hours. • Replace worn or defective parts immediately — contact the Customer
This Jump-Starter is equipped with a safety Power Switch that only allows energy Service Department toll free (866) 584-5504.
to flow when proper connections are made to battery and frame. Once the
connections are properly made, turn the switch ON to jump-start the vehicle.

2 3
VEC012POB_ManualEN_042506 5/19/06 4:14 PM Page 4

CAUTIONS (approximately 15 minutes, depending on ambient temperatures), as

it may overheat. In such event, inflator will automatically shut down
• If the audible Reverse Connection Polarity Alarm sounds after clamps are connected
and restart after a cooling down period of approximately 15 minutes.
to vehicle battery, reverse clamp connections.
• If vehicle fails to start, turn OFF the ignition, turn OFF the Jump-Starter Power Switch, Inflating Tires or Products With Valve Stems
disconnect the jump-start system’s leads and investigate why the engine did not start. 1. Place connector (chuck) on valve stem.
• Recharge this unit fully after each use. 2. Ensure connector is pushed on to valve stem as far as possible before closing
thumb latch.
USING THE 12 VOLT DC PORTABLE POWER SUPPLY 3. Make sure latch is secure.
4. Turn ON the Inflator Power Switch.
This portable power source is also for use with all 12 volt DC accessories equipped
with a male accessory outlet plug and are rated up to 5 amps. 5. Check pressure with the pressure gauge.
1. Lift up the cover of the unit ‘s 12 volt DC outlet. 6. When desired pressure is reached, open thumb latch and remove connector
from valve stem.
2. Insert the 12 volt DC plug from the appliance into the 12 volt DC accessory
outlet on the unit. DO NOT EXCEED A 5 AMP LOAD. 7. Turn OFF Inflator Power Switch.
3. Switch on the appliance and operate as usual. 8. Allow unit to cool before storing away.
4. Periodically press the Battery Charge Level Pushbutton to check battery status. 9. Store inflator hose and tire fitting in storage compartment.

Inflating Other Inflatables Without Valve Stems

USING THE EMERGENCY AREA LIGHT Inflation of other items requires use of one of the adapters (nozzles).
The area light is controlled by the Area Light Power Switch on the front panel of the 1. Select the appropriate nozzle, located on the inside back cover.
unit (see Control and Function Guide). Make sure the lamp is turned OFF when the 2. Insert appropriate adapter (i.e. needle) into connector (chuck) and close thumb
unit is being recharged or stored. latch.
3. Refer to “Typical Inflation Times” for approximate pressure and time. Small
USING THE PORTABLE INFLATOR items such as volleyballs, footballs, etc. inflate very rapidly.
The built-in 12 volt DC inflator is the ultimate inflator for all vehicle tires, trailer tires 4. Insert adapter (i.e., needle) into item to inflate to appropriate pressure.
and recreational inflatables. Three different sized nozzles are supplied. Each nozzle 5. Turn ON the Inflator Power Switch — inflate to desired pressure or fullness.
will clip on the end of the standard tire valve connector located at the free end of 6. Remove adapter.
the inflator hose. The inflator hose with tire fitting is stored in a retaining channel
7. Switch the Inflator Power Switch OFF.
between the jumper cable channels on the rear of the unit. The ON/OFF Switch is
located on the back of the Main Unit. The inflator can operate long enough to fill 8. Recharge the unit before storing away.
up to 3 average sized tires before the battery must be recharged.
The inflator may be used by removing the air hose from the storage hatch and if USING THE USB POWER PORT
required, fitting an appropriate nozzle to the air hose. An On/Off switch located Push the USB Power Switch to the ON position and plug the USB-powered device into
on the back of the unit controls the power to the inflator and the gauge light. Refer the jump-starter’s USB Power Port and operate normally. The green USB LED Indicator
to the Control and Function Guide for location of the inflator hose. Return hose to lights up to indicate that it is working.
the storage compartment after use. Notes: This USB Power Port does not support data communication. It only provides
5 volts/500mA (maximum) DC power to an external USB-powered device.
WARNINGS Push the USB Power Switch to the OFF position when not in use. The green USB
LED will turn OFF.
• The inflator is capable of inflating up to 260 pounds per square inch
(psi) pressure. To avoid over-inflation, carefully follow instructions
on articles to be inflated. Never exceed recommended pressures. CARE AND MAINTENANCE
Bursting articles can cause serious injury. This product has a sealed lead acid battery that should be kept fully charged.
• Always check pressure with the pressure gauge. Recharge before first use, immediately after each use, and once a month if not used
• Never leave the inflator unattended while in use. within that period. Failure to do this may reduce the battery life dramatically.
This unit is delivered in a partially charged state – you must fully charge it before using
CAUTION it for the first time. Initial AC charge should be for 48 hours.
Do not operate inflator continuously for extended periods of time

4 5
VEC012POB_ManualEN_042506 5/19/06 4:14 PM Page 6

Charging/Recharging Fuse Replacement (DC Charging Adapter)

For maximum battery life, we recommend the Jump-Start System be kept fully 1. Remove the plug from the accessory outlet. Remove the gold cap by turning
charged at all times. If the battery is allowed to remain in a discharged state, counterclockwise and lifting off.
battery life will be shortened. 2. Remove the center pin and spring. Remove the fuse.
Note: Recharging battery after each use will prolong battery life; frequent heavy
discharges between recharges and/or overcharging will reduce battery life.
3. Replace the fuse with a same type and size fuse (8 amp).
4. Replace the center pin and spring inside the plug.
120 Volt AC Recharge 5. Replace the gold cap by turning clockwise onto the plug.
1. Plug the AC plug of the AC/DC adapter/charger into any standard 120 volt Battery Replacement/Disposal
AC wall outlet. It is recommended that the unit be returned to manufacturer for battery replacement.
2. Plug the barrel connector attached to the AC/DC adapter into the small barrel Contact Customer Service, toll-free, at (866) 584-5504.
receptacle on the jump-starter.
3. After initial charge, recharge this device as necessary for at least 14-16 hours Battery Disposal
or until the green FULL indicator lights. Recharge at least once a month Contains a maintenance-free, sealed, non-spillable, lead acid
when not in frequent use. battery, which must be disposed of properly. Recycling is
4. When charging is complete and the FULL indicator lights, remove the AC/DC required — contact your local authority for information. Failure
charger plug and store in a safe place. to comply with local, state and federal regulations can result in
Note: The unit cannot be overcharged using the AC method. The Jump-Starter also fines or imprisonment. For more information on recycling this
comes with a DC/DC charging adapter for recharging the unit from a vehicle’s battery, call toll-free (877) 288-7722.
12 volt DC accessory outlet.
WARNINGS
12 Volt DC Charging Do not dispose of the battery in fire, as this may result in an explosion.
The DC recharging method will NOT recharge the unit as effectively as recharging Before disposing of the battery, protect exposed terminals with
from 120 volt AC. The 12 volt DC recharging procedure is recommended only heavy-duty electrical tape to prevent shorting (shorting can result in
when it is necessary, since frequent use of the 12 volt DC recharging procedure injury or fire).
may shorten the battery system’s life. Do not expose battery to fire or intense heat, as it may explode.
1. Insert the gold-tipped DC/DC charging adapter plug into the vehicle’s 12 volt
DC accessory outlet.
SPECIFICATIONS
2. Insert the silver-tipped end plug into the 12 volt DC accessory outlet on the front
panel of the unit. Model: VEC012POB
3. To check the charge status of the battery during DC charging, disconnect the Boost Ampere: 450 instantaneous cranking amps
DC adapter from the accessory outlet and push the Battery Charge Level
Battery Type: Sealed, high energy density, AGM, lead-acid,
pushbutton. Observe the battery charge indicator.
rechargeable, maintenance-free, 12 volt DC
4. When charging is complete, remove the power cord and return it to the storage
compartment. Area Light: Light Emitting Diode (LED)
Booster Cables: Heavy duty welding cable with
WARNING 450 amp copper clamps
Do not recharge for more than 5 to 6 hours maximum using the 12
Accessory Outlet: Self-resetting breaker 5 amps
volt DC method.
DC Charging Adapter: 12 volt DC
Replacement Parts AC Charging Adapter: 120 volt AC (700mA, 12 volt DC output)
For replacement parts (charging adapters, etc.), contact Technical Support, toll free
at (866) 584-5504. USB Power Port: 5 volts/500 mA (maximum) DC power
WARNING
Do not operate unit if there is any evidence of damage. The product
must be returned to Vector Products, Inc. for testing and repair.
Replace any damaged Charging adapters immediately before further
use.

6 7