INTERNATIONAL ISO
STANDARD 8133
Fourth edition
2022-05
Hydraulic fluid power — Mounting
dimensions for accessories for single
rod cylinders, 16 MPa (160 bar)
compact series
Transmissions hydrauliques — Dimensions d'interchangeabilité
des accessoires pour vérins, 16 MPa (160 bar) à simple tige, série
iTeh STANDARD PREVIEW
compacte
(standards.iteh.ai)
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
8133-2022
Reference number
ISO 8133:2022(E)
© ISO 2022
ISO 8133:2022(E)
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
8133-2022
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email:
[email protected] Website: www.iso.org
Published in Switzerland
ii © ISO 2022 – All rights reserved
ISO 8133:2022(E)
Contents Page
Foreword......................................................................................................................................................................................................................................... iv
Introduction..................................................................................................................................................................................................................................v
1 Scope.................................................................................................................................................................................................................................. 1
2 Normative references...................................................................................................................................................................................... 1
3 Terms and definitions..................................................................................................................................................................................... 2
4 Mounting dimensions...................................................................................................................................................................................... 2
5 Tolerances.................................................................................................................................................................................................................... 2
6 Application instructions............................................................................................................................................................................... 2
6.1 Installation.................................................................................................................................................................................................. 2
6.2 Life spherical bearing........................................................................................................................................................................ 2
6.3 Lubrication.................................................................................................................................................................................................. 3
7 Designation................................................................................................................................................................................................................. 3
8 Identification statement (reference to this document)............................................................................................... 3
Bibliography.............................................................................................................................................................................................................................. 14
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
8133-2022
© ISO 2022 – All rights reserved iii
ISO 8133:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
iTeh STANDARD PREVIEW
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
(standards.iteh.ai)
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 3, Cylinders.
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
This fourth edition cancels and replaces the third edition (ISO 8133:2014), which has been technically
revised. 8133-2022
The main are as follows:
— The reference to ISO 3322 (withdrawn) has been replaced by ISO 2944 (Scope);
— Figure 1 has been replaced: bearings type E are used, not type W.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv © ISO 2022 – All rights reserved
ISO 8133:2022(E)
Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure
within an enclosed circuit.
One component of such systems is the fluid power cylinder. This is a device that converts power into
linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod,
operating within a cylindrical bore.
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
8133-2022
© ISO 2022 – All rights reserved v
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
8133-2022
INTERNATIONAL STANDARD ISO 8133:2022(E)
Hydraulic fluid power — Mounting dimensions for
accessories for single rod cylinders, 16 MPa (160 bar)
compact series
1 Scope
This document specifies the mounting dimensions required for interchangeability of accessories for
16 MPa (160 bar) compact cylinders conforming to ISO 6020-2. The accessories have been designed
specifically for use with cylinders manufactured in accordance with ISO 6020-2, but this does not limit
their application1).
This document covers the following accessories, identified in accordance with ISO 6099:
— AP6 — rod eye spherical, female thread (see Figure 1 and Table 1);
— AB5 — clevis bracket, spherical eye, in angle (see Figure 2 and Table 2);
— AA6-L — pivot pin, spherical bearing, locking plate (see Figure 3 and Table 3);
— AL6 — locking plate for pivot pin (see Figure 4 and Table 4);
iTeh STANDARD PREVIEW
— AP2 — rod clevis, female thread (see Figure 5 and Table 5);
— (standards.iteh.ai)
AP4 — rod eye plain, female thread (see Figure 6 and Table 6);
— AB2 — eye bracket (see Figure 7 and Table 7);
ISO 8133:2022
— https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
AB4 — clevis bracket, straight (see Figure 8 and Table 8);
8133-2022
— AA4-S — pivot pin, plain (split pins) (see Figure 9 and Table 9);
— AA4-R — pivot pin, plain (rings) (see Figure 10 and Table 10);
— AT4 — trunnion bracket (see Figure 11 and Table 11).
These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force.
The design of these accessories is based on the maximum forces resulting from the specified internal
diameters of the cylinders and pressures according to ISO 3320 and ISO 2944.
This document only applies to the dimensional criteria of products manufactured in conformity with
this document; it does not apply to their functional characteristics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 286-2, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications
1) 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2
© ISO 2022 – All rights reserved 1
ISO 8133:2022(E)
ISO 5598, Fluid power systems and components — Vocabulary
ISO 6099, Fluid power systems and components — Cylinders — Identification code for mounting dimensions
and mounting types
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://w ww.iso.org/obp
— IEC Electropedia: available at https://w ww.electropedia.org/
4 Mounting dimensions
The mounting dimensions for accessories are shown in Figures 1 to 11 and are given in Tables 1 to 11.
5 Tolerances
5.1 Tolerances values are given in Figures 1 to 11.
iTeh STANDARD PREVIEW
5.2 Tolerances for other linear and angular dimensions shall be in accordance with the designation as
described in ISO 2768-1.
(standards.iteh.ai)
6 Application instructions
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
6.1 Installation
8133-2022
6.1.1 A tolerance of f8 shall be used for plain bearing shafts in accordance with ISO 286-2. A tolerance
of h6 should be used for the shaft fitting the spherical plain bearing bore. In exceptional cases (for
example where there are difficulties in cylinder installation), a tolerance of f7 can be used. In this
instance, a case-hardened shaft is recommended because movement occurs between the shaft and the
bearing bore and lubrication is needed. Lubrication can be carried out through the shaft.
6.1.2 The specified tilting angle of ±3° for the spherical bearing can still be obtained even after the
clevis is in place next to the side faces of the spherical plain bearing's inner ring.
6.1.3 The rod clevis and the rod eye shall be screwed firmly against the piston rod shoulder before
locking.
6.2 Life spherical bearing
6.2.1 The life of the spherical plain bearing is influenced by many factors, such as the specific load,
angle of oscillation, type of lubricant and frequency of lubrication.
6.2.2 The spherical plain bearings are designed to give an acceptable bearing life under normal
operating conditions.
6.2.3 Where a constant unidirectional load is applied or other unusual operating conditions exist,
consultation with the supplier is recommended.
2 © ISO 2022 – All rights reserved
ISO 8133:2022(E)
6.3 Lubrication
6.3.1 Sufficient lubrication for the satisfactory performance of these accessories shall be provided.
6.3.2 The method and frequency of such lubrication depends on the particular operating conditions.
6.3.3 For maintenance-free mating parts, no additional lubrication is required.
7 Designation
Accessories conforming to this document shall be designated by the mounting type identification in
accordance with ISO 6099, followed by “ISO 8133”, followed by a dash, followed by the type (size) from
the relevant table.
EXAMPLE 1 A rod eye spherical, female thread of type 20 (CN = 20) conforming to ISO 8133 is designated:
AP6 ISO 8133 - 20
EXAMPLE 2 A clevis bracket, spherical eye, in angle of type 20 (CF = 20) conforming to ISO 8133 is designated:
AB5 ISO 8133 - 20
EXAMPLE 3 A pivot pin, spherical bearing, locking plate of type 20 (DK = 20) conforming to ISO 8133 is
designated:
iTeh STANDARD PREVIEW
AA6-L ISO 8133 - 20
EXAMPLE 4 A locking plate (standards.iteh.ai)
for pivot pin of type 20 (DK = 20) conforming to ISO 8133 is designated:
AL6 ISO 8133 - 20
ISO 8133:2022
EXAMPLE 5 A rod clevis, female thread of type 20 (CK = 20) conforming to ISO 8133 is designated:
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
AP2 ISO 8133 - 20 8133-2022
EXAMPLE 6 A rod eye plain, female thread of type 20 (CK = 20) conforming to ISO 8133 is designated:
AP4 ISO 8133 - 20
EXAMPLE 7 An eye bracket of type 20 (CK = 20) conforming to ISO 8133 is designated:
AB2 ISO 8133 - 20
EXAMPLE 8 A clevis bracket, straight of type 20 (CK = 20) conforming to ISO 8133 is designated:
AB4 ISO 8133 - 20
EXAMPLE 9 A pivot pin plain (plain split pins) of type 20 (EK = 20) conforming to ISO 8133 is designated:
AA4-S ISO 8133 - 20
EXAMPLE 10 A trunnion bracket of type 20 (CR = 20) conforming to ISO 8133 is designated:
AT4 ISO 8133 - 20
8 Identification statement (reference to this document)
It is strongly recommended to fabricators who elect to conform to this document to use the following
statement in test reports, catalogues, and sales literature when electing to comply with this document:
“Cylinder accessory mounting dimensions conform to ISO 8133, Hydraulic fluid power — Mounting
dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series.”
© ISO 2022 – All rights reserved 3
ISO 8133:2022(E)
Figure 1 — AP6 — Rod eye spherical, female thread
Table 1 — Dimensions of AP6 — Rod eye spherical, female thread
iTeh STANDARD PREVIEW Dimensions in millimetres
CN EN Tilting
Type
Nominal
force
N
max.
KK
6H
(standards.iteh.ai)
nom. tol. nom. tol. EF CH AV LF EU
max. js13 min. min. max.
angle
Z
N µm µm
min.
12 8 000 19 M10 × 1,25 12 0 ISO
10 8133:2022 18 42 15 16 8,5
16 https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
12 500 22 M12 × 1,25 16 −8 14 23 48 17 20 11,5
20 20 000 28 M14 × 1,5 20 8133-2022
16 28 58 19 25 13,5
0 0
25 32 000 31 M16 × 1,5 25 20 33 68 23 30 18
−10 −120
30 50 000 37 M20 × 1,5 30 22 41 85 29 35 20
40 80 000 47 M27 × 2 40 0 28 51 105 37 45 24 3°
50 125 000 57 M33 × 2 50 −12 35 61 130 46 58 31
60 200 000 69 M42 × 2 60 0 44 0 80 150 57 68 39
80 320 000 91 M48 × 2 80 −15 55 −150 102,5 185 64 92 48
0 0
100 500 000 110 M64 × 3 100 70 120 240 86 116 57
−20 −200
NOTE For spherical bearings see ISO 12240-1, type E.
4 © ISO 2022 – All rights reserved
ISO 8133:2022(E)
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8133:2022
https://standards.iteh.ai/catalog/standards/sist/eedf63a8-d0fb-4859-993c-5ca9d4e3a01b/iso-
8133-2022
a Separate spacers are permitted to maintain CG and CS dimensions.
b Tapped holes are required only when using a pivot pin with a locking plate.
Figure 2 — AB5 — Clevis bracket, spherical eye, in angle
© ISO 2022 – All rights reserved 5
