Scribd Logo
Upload

Welcome to Scribd!

  • 2 views

    Specs Epoxylite-E230 Resine

    Uploaded by

    otto.chopen.s

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Specs Epoxylite-E230 Resine

    Uploaded by

    otto.chopen.s
    2 views3 pages

    Original Title

    Specs Epoxylite-E230 resine

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2 views3 pages

    Specs Epoxylite-E230 Resine

    Uploaded by

    otto.chopen.s

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Technical Data Sheet

    Secondary Insulation

    Epoxylite® E 230
    Two-Component Epoxy Impregnating Resin

    ELANTAS PDG, Inc.


    5200 North Second Street
    St. Louis, MO 63147
    USA
    Tel +1 314 621-5700
    Fax +1 314 436-1030
    [email protected]
    www.elantas.com
    Epoxylite® E 230 Epoxy
    Product Description Application Methods

    Epoxylite® E 230 Epoxy is a two-component, low Trickle


    temperature curing, 100%-solids resin system. Brush on

    Areas of Application Transportation / Storage

    Impregnation of motor and transformer windings Store below 25°C / 77°F in a dry controlled
    including high-speed armatures environment out of direct sunlight. This material
    should be suitable for use stored under these
    Protective overcoat for motor windings conditions in the original sealed containers for
    twelve (12) months from the date of shipment.
    Features and Benefits
    Failure to store the product as recommended
    • Excellent penetration in trickle above may lead to deterioration in product
    application performance.

    • High bond strength Mix individual components thoroughly before


    use.
    • Chemical, refrigerant and moisture
    resistant Health / Safety

    • Fast cure with low heat Refer to the Material Safety Data Sheet.

    • Ideal for appliance motors and other


    high-speed rotating devices

    Typical Properties of Material as Supplied

    Property Conditions Value Units


    ® ®
    Epoxylite Epoxylite
    E 230 Resin C 230 Hardener

    Viscosity 25°C / 77°F 10,000 – 15,000 100 - 500 cP

    Weight per Gallon 25°C / 77°F 9.5 – 9.9 8.4 – 8.8 pounds
    248 > 94 °C
    Flash Point ASTM D93
    478 > 201 °F
    Parts by weight 100 20
    Mix Ratio
    Parts by volume 100 22.6

    ®
    Epoxylite E 230 R02 07/28/11 Page 2 of 3
    Epoxylite® E 230 Epoxy
    Typical Properties of Mixed Materials

    Property Conditions Value Units


    Viscosity 25°C / 77°F 3,000 - 6,000 cP

    Gel Time 25°C / 77°F – 250 grams 15 - 25 minutes

    Application / Curing Schedule

    Preheat unit to 85 - 95°C / 185 - 203°F

    Trickle mixed resin onto unit and allow to gel. Post-cure 15 minutes at 100°C / 212°F. Allow 2 - 7 days
    to develop full properties.

    Alternatively, allow to gel at room temperature and post-cure for 16 hours at 60°C / 140°F.

    Cure schedule is based on time after the unit reaches the specified temperature.

    Typical Mechanical Properties

    Property Conditions Value Units


    Helical Coil Bond Strength 25°C / 77°F 40 pounds
    ASTM D2519 over MW 35 150°C / 302°F 4 pounds
    Hardness Shore D 75 - 85

    R-22 Extractable Material NEMA RE-2 < 1.0 %

    Water Absorption 24 hours @ 25°C / 77°F 0.2 %

    Typical Electrical Properties

    Property Conditions Value Units


    Dielectric Strength
    25°C / 77°F - 3 mils 1700 volts/mil
    ASTM D149
    Volume Resistivity ASTM D257 – 25°C / 77°F 1.1 x 1015 ohm-cm

    Dielectric Constant 1 kHz – 25°C / 77°F 3.8

    Dissipation Factor 1 kHz – 25°C / 77°F 0.03

    The above properties are typical values and are not intended for specification use.

    ELANTAS PDG, Inc. warrants the chemical composition of its products within stated tolerances, but does not guarantee that a
    product will be appropriate for any particular application. Any recommendation, performance of tests or suggestion is offered merely
    as a guide and is not a substitute for a thorough evaluation by the user. No representative of ELANTAS PDG, Inc. has the authority
    to offer a warranty that a product will perform satisfactorily in manufacturing a product and no such representation should be relied
    upon.

    ®
    Epoxylite E 230 R02 07/28/11 Page 3 of 3

    You might also like