Ruijie Reyee RG-RAP Series Access Points Web-Based Configuration Guide, Release ReyeeOS 1.210 (V1.2)

Ruijie Reyee RG-RAP Series Access
Points
ReyeeOS 1.210
Web-based Configuration Guide
Document Version: V1.2

Date: 2023-09-06
Copyright © 2023 Ruijie Networks
Copyright
Copyright © 2023 Ruijie Networks
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document
or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks
is prohibited.
Trademarks including , are owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.
Preface
Intended Audience
This document is intended for:
 Network engineers
 Technical support and servicing engineers
 Network administrators
Technical Support
 Official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
 Technical support website: https://ruijienetworks.com/support
 Case portal: https://caseportal.ruijienetworks.com
 Community: https://community.ruijienetworks.com
 Technical support Email: [email protected]
Conventions
1. GUI Symbols
Interface
Description Example
symbol
1. Button names
1. Click OK.
2. Window names, tab name, field name and
Boldface 2. Select Config Wizard.
menu items
3. Click the Download File link.
3. Link
> Multi-level menus items Select System > Time.
2. Signs
The signs used in this document are described as follows:
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.
I
Specification
An alert that contains a description of product or version support.
3. Note
This manual introduces the product model, port type and CLI for your reference. In case of any discrepancy or
inconsistency between the manual and the actual version, the actual version prevails.
II
Contents
Preface .................................................................................................................................................. I
1 Fast Internet Access.......................................................................................................................... 1
1.1 Configuration Environment Requirements ................................................................................ 1
1.1.1 PC .................................................................................................................................. 1
1.2 Default Configuration ................................................................................................................. 1
1.3 Login to Eweb ............................................................................................................................ 1
1.3.1 Connecting to the Access Point ..................................................................................... 1
1.3.2 Configuring the IP Address of the Management Client ................................................. 2
1.3.3 Logging in to the Web Page .......................................................................................... 2
1.4 Work Mode ................................................................................................................................. 3
1.4.1 AP Mode ......................................................................................................................... 3
1.4.2 Router Mode .................................................................................................................. 3
1.4.3 Wireless Repeater Mode ............................................................................................... 3
1.5 Configuration Wizard (Router Mode) ......................................................................................... 4
1.5.1 Getting Started ............................................................................................................... 4
1.5.2 Configuration Steps ....................................................................................................... 5
1.6 Configuration Wizard (AP Mode) ............................................................................................... 7
1.6.1 Getting Started ............................................................................................................... 7
1.7 Configuration Wizard (Wireless Repeater Mode) ...................................................................... 8
1.7.1 Getting Started ............................................................................................................... 8
1.8 Introduction to the Eweb GUI................................................................................................... 10
i
1.8.1 Single Management Webpage .................................................................................... 10
1.8.2 Dual Management Webpages ..................................................................................... 12
2 Network Monitoring ......................................................................................................................... 15
2.1 Viewing the Network Information ............................................................................................. 15
2.2 Adding Network Devices.......................................................................................................... 17
2.2.1 Wired Connection ........................................................................................................ 17
2.2.2 AP Mesh ....................................................................................................................... 19
2.3 Managing Network Devices ..................................................................................................... 28
2.4 Configuring Network Planning ................................................................................................. 30
2.4.1 Configuring Wired VLAN .............................................................................................. 30
2.4.2 Configuring Wi-Fi VLAN ............................................................................................... 32
2.5 Troubleshooting Fault Alerts .................................................................................................... 34
3 Wi-Fi Network Settings.................................................................................................................... 36
3.1 Configuring AP Groups ............................................................................................................ 36
3.1.1 Overview ...................................................................................................................... 36
3.1.2 Procedures ................................................................................................................... 36
3.2 Configuring SSID and Wi-Fi Password ................................................................................... 38
3.3 Hiding the SSID ....................................................................................................................... 39
3.3.1 Overview ...................................................................................................................... 39
3.3.2 Configuration Steps ..................................................................................................... 39
3.4 Checking Wireless Clients ....................................................................................................... 40
3.5 Configuring Wi-Fi Band............................................................................................................ 42
3.6 Configuring Band Steering....................................................................................................... 42
3.7 Configuring Wi-Fi 6 .................................................................................................................. 43
ii
3.8 Configuring Layer-3 Roaming .................................................................................................. 44
3.9 Configuring AP Isolation .......................................................................................................... 45
3.10 Adding a Wi-Fi Network ......................................................................................................... 46
3.11 Configuring a Guest Wi-Fi ..................................................................................................... 47
3.11.1 Overview .................................................................................................................... 47
3.11.2 Configuration Steps .................................................................................................... 47
3.12 Configuring Wi-Fi Blacklist or Whitelist .................................................................................. 48
3.12.1 Overview .................................................................................................................... 48
3.12.2 Configuration Steps ................................................................................................... 48
3.13 Optimizing Wi-Fi Network ...................................................................................................... 50
3.13.1 Overview .................................................................................................................... 50
3.13.2 Getting Started ........................................................................................................... 50
3.13.3 Optimizing the Radio Channel ................................................................................... 51
3.13.4 Optimizing the Channel Width ................................................................................... 52
3.13.5 Optimizing the Transmit Power .................................................................................. 53
3.13.6 Configuring the Kick-off Threshold ............................................................................ 54
3.13.7 Configuring the Client Limit........................................................................................ 55
3.13.8 Configuring the Roaming Sensitivity .......................................................................... 55
3.13.9 Configuring WIO ........................................................................................................ 56
3.13.10 Configuring Wi-Fi Roaming Optimization (802.11k/v) ............................................. 57
3.14 Configuring Healthy Mode ..................................................................................................... 58
3.15 Configuring XPress ................................................................................................................ 59
3.16 Configuring Wireless Schedule ............................................................................................. 60
3.17 Enabling Reyee Mesh ............................................................................................................ 61
iii
3.18 Configuring AP Load Balancing............................................................................................. 61
3.18.1 Overview .................................................................................................................... 61
3.18.2 Configuring Client Load Balancing ............................................................................ 62
3.18.3 Configuring Traffic Load Balancing ............................................................................ 63
4 Network Settings ............................................................................................................................. 65
4.1 Switching Work Mode .............................................................................................................. 65
4.1.1 Work Mode ................................................................................................................... 65
4.1.2 Self-Organizing Network Discovery ............................................................................. 65
4.1.3 Configuration Steps ..................................................................................................... 65
4.1.4 Viewing Device Role .................................................................................................... 67
4.2 Configuring Internet Type ........................................................................................................ 67
4.3 Configuring LAN Port ............................................................................................................... 68
4.4 Configuring Repeater Mode..................................................................................................... 69
4.4.1 Wired Repeater ............................................................................................................ 69
4.4.2 Wireless Repeater ....................................................................................................... 70
4.5 Creating a VLAN ...................................................................................................................... 72
4.6 Configuring Port VLAN ............................................................................................................ 74
4.7 Changing MAC Address .......................................................................................................... 76
4.8 Changing MTU ......................................................................................................................... 77
4.9 Configuring DHCP Server........................................................................................................ 77
4.9.1 DHCP Server ............................................................................................................... 77
4.9.2 Configuring the DHCP Server Function ....................................................................... 77
4.9.3 Displaying Online DHCP Clients.................................................................................. 79
4.9.4 Displaying the DHCP Static IP Address List ................................................................ 79
iv
4.10 Link Aggregation .................................................................................................................... 80
4.11 Configuring DNS .................................................................................................................... 80
4.12 Hardware Acceleration .......................................................................................................... 81
4.13 Configuring Port Flow Control ............................................................................................... 81
4.14 Configuring ARP Binding ....................................................................................................... 82
4.15 Configuring LAN Ports ........................................................................................................... 83
5 System Settings .............................................................................................................................. 85
5.1 PoE .......................................................................................................................................... 85
5.2 PoE Settings ............................................................................................................................ 85
5.3 Setting the Login Password ..................................................................................................... 86
5.4 Setting the Session Timeout Duration ..................................................................................... 87
5.5 Setting and Displaying System Time ....................................................................................... 87
5.6 Configuring Reboot .................................................................................................................. 89
5.6.1 Rebooting the Current Device ..................................................................................... 89
5.6.2 Rebooting All Devices in the Network .......................................................................... 89
5.6.3 Rebooting the Specified Device................................................................................... 90
5.7 Configuring Scheduled Reboot................................................................................................ 91
5.7.1 Configuring Scheduled Reboot for the Current Device ............................................... 91
5.8 Configuring Backup and Import ............................................................................................... 92
5.9 Restoring Factory Settings ...................................................................................................... 93
5.9.1 Restoring the Current Device to Factory Settings ....................................................... 93
5.9.2 Restoring All Devices to Factory Settings.................................................................... 94
5.10 Performing Upgrade and Checking System Version............................................................. 94
5.10.1 Online Upgrade .......................................................................................................... 94
v
5.10.2 Local Upgrade ............................................................................................................ 95
5.11 Switching System Language ................................................................................................. 95
5.12 Configuring LED Status Control ............................................................................................ 96
6 Network Diagnosis Tools ................................................................................................................. 97
6.1 Network Check......................................................................................................................... 97
6.2 Network Tools .......................................................................................................................... 98
6.3 Alarms ...................................................................................................................................... 99
6.4 Fault Collection ...................................................................................................................... 100
7 FAQs.............................................................................................................................................. 102
7.1 Login Failure .......................................................................................................................... 102
7.2 Factory Setting Restoration ................................................................................................... 102
7.3 Password Loss....................................................................................................................... 102
vi
Web-based Configuration Guide Fast Internet Access
1 Fast Internet Access

1.1 Configuration Environment Requirements
1.1.1 PC
 Browser: Google Chrome, Internet Explorer 9.0, 10.0, and 11.0, and some Chromium/Internet Explorer
kernel-based browsers (such as 360 Extreme Explorer) are supported. Exceptions such as garble or format
error may occur if an unsupported browser is used.
 Resolution: 1024 x 768 or a higher resolution is recommended. If other resolutions are used, the page fonts
and formats may not be aligned, the GUI is less artistic, or other exceptions may occur.
1.2 Default Configuration
Table 1-1 Default Web Configuration
Item Default
IP address 10.44.77.254
Username and password are not required at your first

Username/Password
login and you can configure the access point directly.
1.3 Login to Eweb
1.3.1 Connecting to the Access Point
You can open the management page and complete Internet access configuration only after connecting a client
to the access point in either of the following ways:
 Wired Connection
Connect a local area network (LAN) port of the access point to the network port of the PC, and set the IP address
of the PC. See Configuring the IP Address of the Management Client.
 Wireless Connection
On a mobile phone or laptop, search for wireless network @Ruijie-SXXXX (XXXX is the last four digits of the
MAC address of each device). In this mode, you do not need to set the IP address of the management Client,
and you can skip the operation in Configuring the IP Address of the Management Client.
1
1.3.2 Configuring the IP Address of the Management Client
Configure an IP address for the management client in the same network segment as the default IP address of
the device (The default device IP address is 10.44.77.254, and the subnet mask is 255.255.255.0.) so that the
management client can access the device. For example, set the IP address of the management client to
10.44.77.100.
Caution
● Make sure that the client can access the Eweb system as long as it can ping the access point.
● The IP address of the management client cannot be set to 10.44.77.253, because this IP address is
reserved by the device. If the management client uses this IP address, it cannot access the device.
1.3.3 Logging in to the Web Page
(1) Enter the IP address (10.44.77.254 by default) of the access point in the address bar of the browser to open
the login page.
Note
If the static IP address of the device is changed, or the device obtains a new dynamic IP address, the new IP
address can be used to access the web management system of the device as long as the management client
and the device are in the same network segment of a LAN.
(2) On the web page, enter the password and click Log In to enter the web management system.
Username and password are not required at your first login and you can configure the access point directly.
For device security, you are advised to set the management password after your first login to the web
management system. After the password is set, you need to enter the password when you log in to the web
management system again.
2
If you forget the IP address or password, hold down the Reset button on the device panel for more than 5
seconds when the device is connected to the power supply to restore factory settings. After restoration, you
can use the default IP address and password to log in.
Caution
Restoring factory settings will delete the existing configuration and you are required to configure the device
again at your next login. Therefore, exercise caution when performing this operation.
1.4 Work Mode

The device can work in the router mode, AP mode or wireless repeater mode. The displayed system menu page
and function ranges vary with the work mode. The RAP works in the AP mode by default. If you want to switch
the work mode, see Switching Work Mode.
1.4.1 AP Mode
The device performs L2 forwarding and does not support the DHCP address pool function. In AP mode, the
device often networks with devices supporting the routing function. IP addresses of downlink wireless clients are
assigned and managed by the uplink device (supporting the DHCP address pool) of the AP in a unified manner,
and the AP only transparently transmits data.
1.4.2 Router Mode
The device supports NAT routing and forwarding. The addresses of wireless clients can be assigned by the AP
and wireless network data is routed and forwarded by the AP. NAT is supported in this mode. When an AP works
in the router mode, it supports device networking, network-wide configuration, and AP-specific radio functions.
There are three Internet types available: PPPoE, DHCP mode and static IP address mode. You can connect the
device to an Ethernet cable or an upstream device.
Caution
After switching to the router mode, the device’s LAN IP address will change to 192.168.120.1. Please obtain
an IP address automatically for your management client and enter 10.44.77.254 into the address bar of the
browser to log in to Eweb again.
1.4.3 Wireless Repeater Mode
The device does not support the routing and DHCP server functions in the wireless repeater mode. IP addresses
of the clients are assigned and managed by the primary router. On an available network, the device can be
connected to the primary router through wireless connection to expand the Wi-Fi coverage and increase the
number of LAN ports and wireless access devices.
3
1.5 Configuration Wizard (Router Mode)

Upon first login, you can perform quick configuration procedures to configure the Internet type, Wi-Fi network
and management password.
1.5.1 Getting Started
(1) Connect the device to a power supply and connect the port of the device to an upstream device with an
Ethernet cable. Or you can connect an Ethernet cable to the device.
(2) Configure the Internet connection type according to requirements of the local Internet Service Provider (ISP).
Otherwise, the Internet access may fail due to improper configuration. You are advised to contact your local
ISP to confirm the Internet connection type:
○ Figure out whether the Internet connection type is PPPoE, DHCP mode, or static IP address mode.
○ In the PPPoE mode, a username, a password, and possibly a service name are needed.
○ In the static IP address mode, an IP address, a subnet mask, a gateway, and a DNS server need to be
configured.
(3) The device works in the AP mode by default. If you want to switch the work mode to the router mode, perform
the configuration on the work mode setting page. See Switching Work Mode for more details.
4
1.5.2 Configuration Steps
1. Add a Device to Network
You can manage and configure all devices in the network in batches by default. Please verify the device count
and network status before configuration.
Note
New devices will join in a network automatically after being powered on. You only need to verify the device
count.
If a new device is detected not in the network, click Add to My Network and enter its management password
to add the device manually.
2. Creating a Network Project
Click Start Setup to configure the Internet connection type, Wi-Fi network and management password.
(1) Network Name: Identify the network where the device is located.
(2) Internet: Configure the Internet connection type according to requirements of the local Internet Service
Provider (ISP).
○ DHCP: The access point detects whether it can obtain an IP address via DHCP by default. If the access
point connects to the Internet successfully, you can click Next without entering an account.
○ PPPoE: Click PPPoE, and enter the username, password, and service name. Click Next.
5
○ Static IP: Enter the IP address, subnet mask, gateway, and DNS server, and click Next.
(3) SSID and Wi-Fi Password: The device has no Wi-Fi password by default, indicating that the Wi-Fi network
is an open network. You are advised to configure a complex password to enhance the network security.
(4) Management Password: The password is used for logging in to the management page.
(5) Country/Region: The Wi-Fi channel may vary from country to country. To ensure that a client searches for
a Wi-Fi network successfully, you are advised to select the actual country or region.
(6) Time Zone: Set the system time. The network time server is enabled by default to provide the time service.
You are advised to select the actual time zone.
Click Create Network & Connect. The device will deliver the initialization and check the network connectivity.
6
The device can access the Internet now. Bind the device with a Ruijie Cloud account for remote management.
Follow the instruction to log in to Ruijie Cloud for further configuration.
Note
● If your device is not connected to the Internet, click Exit to exit the configuration wizard.
● Please log in again with the new password if you change the management password.
1.6 Configuration Wizard (AP Mode)
 Power on the device and connect the device to an upstream device.
 Make sure that the device can access the Internet.
The device obtains the IP address through the DHCP by default. Configure the SSID, Wi-Fi password and
management password. The default Internet connection type is DHCP mode. You are advised to use the default
value.
7
1.7 Configuration Wizard (Wireless Repeater Mode)
 Before configuring the wireless repeater mode, configure the primary router and test that the primary router
can access the Internet.
 Place the device where it can discover at least two-bar Wi-Fi signal of the primary router.
Caution
● No Ethernet cable is required in the wireless repeater mode. The wireless network stability can be
affected by many factors. Therefore, the wired connection is recommended.
(1) Connect the device to a power supply without connecting an Ethernet cable to the uplink port, and click
Start Setup.
(2) If you see a dialogue box indicating that the Ethernet cable is not connected to the WAN port, click Wireless
Repeater.
8
(3) Select the primary router SSID that requires expanding the Wi-Fi coverage, enter the Wi-Fi password of the
primary router, and click Next.
(4) Set the SSID and password and click Save. Then, the Wi-Fi network will be restarted.
9
1.8 Introduction to the Eweb GUI

To facilitate flexible device management, the Web page displays different system configuration menus in different
work modes. For details about the work mode, see Switching Work Mode.
As to the RG-RAP2260(G), RG-RAP2260(E), RG-RAP6260(G), RG-RAP6262(G), RG-RAP2260(H), RG-

RAP6260(H), RG-RAP6260(H)-D, RG-RAP1261, RG-RAP2266, RG-RAP2260, RG-RAP1260 and RG-
RAP6262 models, please refer to Dual Management Webpages.
As to other RAP models, please refer to Single Management Webpage.
Note
When the self-organizing network is enabled, the Eweb GUI is subject to the master device in the network. If
the master device supports the dual management webpages, the slave device also displays the dual
management webpages.
1.8.1 Single Management Webpage
1. Network-wide Management
The device works in self-organizing network mode by default. The Web page displays the network-wide
management menu on the left side, in which you can check the current status of all devices in the network, and
modify network-wide configuration, including global Wi-Fi network management configuration (APs and Wi-Fi),
routing management configuration (if routers exist in the network), switch management configuration, and
network-wide management configuration (time, password, network-wide reboot, and other system settings).
10
2. Standalone Management
 If a device is in self-organizing network mode, click the name of the currently logged in device or click Manage
of a specified device in the device list to configure and manage the device.
11
 If a device is in standalone mode, you can configure and manage only the currently logged in device. The
Web page displays the function configuration menu of a single device on the left side.
1.8.2 Dual Management Webpages
1. Introducing the Management Mode
If the self-organizing network is disabled (The function is enabled by default. See Switching Work Mode for
details.), the device works in the local device mode displayed on the Web page.
12
If the self-organizing network is enabled, the device can work in the network mode and the local device mode.
The two modes can be switched on the Web page.
 Network mode: View the management information of all devices in the network, and configure all devices
based on network management.
 Local Device mode: Only configure the currently logged in devices.
Network mode webpage
Local Device mode webpage
13
2. Switching the Management Mode
Click the current management mode in the navigation bar, and select the mode in the drop-down box to switch
the work mode of the device.
14
Web-based Configuration Guide Network Monitoring
2 Network Monitoring
Note
The functions mentioned in this chapter are only applicable to such models as RG-RAP2260(G), RG-
RAP2260(E), RG-RAP6260(G), RG-RAP6262(G), RG-RAP2260(H), RG-RAP6260(H), RG-RAP6260(H)-D,
RG-RAP1261, RG-RAP2266, RG-RAP2260, RG-RAP1260 and RG-RAP6262.
In Network mode, select Overview.
The Overview webpage displays the current network topology, real-time uplink and downlink flow, networking
status, and the number of users. The quick access to network and device settings is also provided on the
Overview webpage. Users can monitor, configure and manage the network status on the current page.
2.1 Viewing the Network Information

You can view the online device, port ID, device SN as well as the real-time uplink and downlink flow in the
network topology.
15
 Click the flow data and view the real-time flow.
 Click the device in the topology to view the operating status and configuration of the device and configure
the device functions. The hostname is set to the product model by default. You can click to modify the
hostname.
16
 The update time of the topology is displayed at the bottom left corner. Click Refresh to update the topology
to the latest status. Please wait for a few minutes for the update.
2.2 Adding Network Devices
2.2.1 Wired Connection
(1) If a new device is connected to the device in the network through wired connection, a prompt message will
pop up, indicating that a device not in SON (Self-Organizing Network) is discovered. The number (in orange)
17
of devices that are not in SON is displayed under the Devices at the top left corner of the page. Click
Manage to add the device to the current network.
(2) Go to the Network List page, click Other Network to select the target device and click Add to My Network.
18
If the target device is not configured yet, you can add the device directly without a password. If the device is
configured with a password, please enter the management password of the device. If the password is incorrect,
the device cannot be added to the network.
2.2.2 AP Mesh
Note
This function is not supported by RG-RAP1200(F), and RG-RAP2200(F).
19
1. Overview
After being powered on and enabled with Mesh (see 3.17 Enabling Reyee Mesh for details), a Mesh-capable
new AP can be paired with other Mesh-capable wireless devices on the target network through multiple ways.
Then the AP will be synchronized its Wi-Fi configuration with other devices automatically. Mesh networking
addresses pain points such as complex wireless networking and cabling. A new AP can be connected to any
uplink wireless device among AP, EG router, and EGW router in the following ways:
 Button-based pairing: Short press the Mesh button on the EGW router on the target network to implement
fast pairing of the AP with the EGW router.
 Search-based pairing: Log in to the Eweb of a device on the target network. Search and add APs to be paired.
 Wired pairing: Connect the new AP to a wireless device on the target network using an Ethernet cable. The
new AP will go online on the target network.
After pairing finishes, the new AP obtains the wireless backhaul information from network-wide neighboring APs.
Install the new AP as planned, and it will connect to the optimal neighboring AP.
2. Configuration Procedure
Start
Button Wired Connection

Pairing Mode?
Eweb-based Scanning
Button-based Pairing Search-based Pairing Wired Pairing
(Uplink Device is
(Uplink Device is EGW) (Uplink Device is AP/EGW) AP/EG/EGW)
Verify AP Connection
Install AP
Verify Mesh Networking
Finish
3. Configuration Steps for Button-based Pairing (Uplink Device is an EGW Router)
Caution
● Only EG105GW-X and EG105GW(T) support button-based pairing and each router can be paired with up
to 15 new APs.
● The new AP must be in factory status.
● It can be scanned only when the live network is enabled with Mesh (see Enabling Reyee Mesh for
details).
20
● Place the new AP no more than 2 meters away from the uplink device to ensure that the new AP can
receive the Wi-Fi signal from the uplink device. The new AP may fail to be scanned due to the long
distance or obstacles between it and the uplink device.
(1) Power on the new AP and place it near the EGW router on the target network.
(2) Press and hold the Mesh button on the EGW router for no more than two seconds to start pairing.
The pairing process takes about one minute.
(3) Check the topology on the Overview page to make sure that the new AP has connected to the uplink device
in wireless mode.
(4) Power off the new AP and install it as planned.
(5) Log in to the Eweb of a device on the target network. In Network mode, choose Devices > AP. Make sure
that the new AP is online and the corresponding entry contains icon in the Relay
Information column. The icon indicates that wireless backhaul is performed through the 5 GHz radio.
Click View Details following the icon to obtain information about the uplink device and
RSSI.
21
4. Configuration Steps for Search-based Pairing (Uplink Device is an AP or EGW Router)
Caution
● It can be scanned only when the live network is enabled with Mesh (see Enabling Reyee Mesh for
details).
● Place the new AP no more than 2 meters away from the uplink device to ensure that the new AP can
receive the Wi-Fi signal from the uplink device. The new AP may fail to be scanned due to the long
distance or obstacles between it and the uplink device.
(1) Power on the new AP and place it near the AP or EGW router on the target network.
(2) Log in to the Eweb of a device on the target network. In Network mode, click +AP in the upper right corner
of the Overview page to scan the APs in other networks not plugged in with Ethernet cables.
(3) Select the APs to be added and click Add to My Network. No more than eight APs are allowed at a time.
Wait until network merging finishes.
22
(4) Check the topology on the Overview page to make sure that the new AP has connected to the uplink device
in wireless mode.
23
(5) Power off the new AP and install it as planned.
RSSI.
24
5. Configuration Steps for Wired Pairing (Uplink Device is an AP, EG Router, or EGW Router)
Caution
● It can be scanned only when the live network is enabled with Mesh (see 3.17 Enabling Reyee Mesh
for details).
(1) Plug one end of the Ethernet cable to the uplink port of the new AP, and the other end to the downlink port of
an AP, EG router, or EGW router on the target network. Mesh networking takes one to three minutes. When
the system status LED is steady on, it indicates that Mesh networking finishes.
(2) Log in to the Eweb of a device on the target network. In Network mode, choose Devices and make sure that
the new AP is online.
(3) Unplug the Ethernet cable, power off the new AP, and install it as planned.
25
RSSI.
6. Enabling WAN Port
The WAN port works as the wired uplink port of the AP by default. For the AP added to the target network through
Mesh pairing, the WAN port is disabled by default. If you want to connect the Mesh AP to other downlink device
in wired mode to expand the network, enable this port.
(1) Log in to the Eweb of a device on the target network. In Network mode, choose Devices > AP and click the
serial number of the Mesh AP with the WAN port to be enabled.
26
(2) Choose More > Advanced > Enable WAN, toggle on Enable, and click Save.
7. Querying Mesh APs and Mesh Details
(1) Log in to the Eweb of a device on the target network.
(2) Query Mesh APs.
 Method 1: In Network mode, check the topology on the Overview page. The AP that connects to the uplink
device in wireless mode is a Mesh AP.
 Method 2: In Network mode, choose Devices > AP. If an entry contains icon in the Relay
Information column, the corresponding AP is a Mesh AP.
27
(3) Query Mesh networking details.
In Network mode, choose Devices > AP. Select the target AP, and click View Details in the Relay
Information column to obtain the Mesh networking details.
2.3 Managing Network Devices

Click List at the top left corner of the topology or click Devices in the menu bar to switch to the device list view,
and view the information of all devices in the self-organizing network (SON). You can perform configurations and
management on all devices by logging in to only one device in the network.
28
 Click SN to configure the specified device.
 Select the offline device and click Delete Offline Devices to remove the device from the list and the topology.
29
2.4 Configuring Network Planning

The Overview page displays the configuration of Network Planning at the bottom left corner, including Wi-Fi
VLAN and Wired VLAN.
 Click manage to go to the Network Planning page for configuration (Network > Network Planning). You
can add or edit the Network Planning configuration for the live network.
 Click Add to configure Wi-Fi VLAN or Wired VLAN for the live network.
 Click the SSID to edit the Wi-Fi configuration. For details, see Chapter 3 Wi-Fi Network Settings.
2.4.1 Configuring Wired VLAN
(1) Go to the Wired VLAN page for configuration.
 Method 1: Click Add beside Wired VLAN in the Network Planning area on the Overview page to add the
30
wired VLANs.
 Method 2: Click manage in the Network Planning area on the Overview page to go to the Network
Planning page for configuration (Network > Network Planning). Click Add Wired VLAN to add the wired
VLANs to the live network or select the available wired VLANs. Click Setup to configure the wired VLANs.
(2) Configure the VLAN ID, address pool server, and DHCP pool. The gateway is configured as the address pool
server by default to assign IP addresses to clients. If an access switch exists in the network, you can select
the access switch as the address pool server. Click Next after VLAN parameters are configured.
(3) Select the target switch in the topology and all member ports in the VLAN, and click Next.
31
(4) Please confirm the delivered configurations and click Save. The configurations will take effect after a few
minutes.
2.4.2 Configuring Wi-Fi VLAN
(1) Go to the Wired VLAN page for configuration.
 Method 1: Click Add beside Wi-Fi VLAN in the Network Planning area on the Overview page to add the
Wi-Fi VLANs.
 Method 2: Click manage in the Network Planning area on the Overview page to go to the Network
Planning page for configuration (Network > Network Planning). Click Add Wi-Fi VLAN to add the Wi-Fi
VLANs to the live network or select the available Wi-Fi VLANs. Click Setup to configure the Wi-Fi VLANs.
32
(2) Configure the SSID, Wi-Fi password and band. Click Expand to expand the advanced settings and set the
parameters. Then, click Next.
(3) Configure the VLAN ID, address pool server and DHCP pool. The gateway is configured as the address pool
server by default to assign IP addresses to clients. If an access switch exists in the network, you can select
the access switch as the address pool server. Click Next after VLAN parameters are configured.
33
(4) Please confirm the delivered configurations and click Save. The configurations will take effect after a few
minutes.
2.5 Troubleshooting Fault Alerts

The Overview page displays the fault alerts and handling suggestions if faults occur in the network. Click the
fault alert in Alert Center to view the faulty device, fault details and handling suggestions, and troubleshoot
device faults by referring to the handling suggestions.
34
35
Web-based Configuration Guide Wi-Fi Network Settings
3 Wi-Fi Network Settings

Note
Wi-Fi network settings covers the Wi-Fi settings of the currently logged in devices and the management of all
wireless devices in the network. In Network mode, the Wi-Fi network settings are synchronized to all wireless
devices in the network. You can configure device groups to limit the synchronization range. For details, see
Configuring AP Groups.
3.1 Configuring AP Groups
3.1.1 Overview
After the self-organizing network is enabled, the device can act as the master AP/AC to perform batch
configuration and management on the downlink APs in groups. Group the APs before the configurations are
delivered.
Note
If you specify a group when setting up a wireless network, the corresponding configuration will take effect on
the wireless devices in the specified group.
3.1.2 Procedures
For RG-RAP2260(G), RG-RAP2260(E), RG-RAP6260(G), RG-RAP6262(G), RG-RAP2260(H), RG-

RAP6262 models: In Network mode, choose Devices > AP
For other RAP models, choose WLAN > APs
(1) View the information of all APs in the current network, including the basic information, RF information and
models. You can click SN to configure the device.
36
(2) Click Expand to view all groups on the left part of the Device List page. Click to create a new group.
Up to 8 groups can be added. You can click to edit the group name and click to delete the group.
The default group cannot be deleted and its name cannot be edited.
(3) Click the group name on the left part to view all devices in this group. A device can only belong to a group.
By default, all devices belong to the default group. Select an entry in the list and click Change Group to
move the target device to a specified group, and then the device will apply the configurations of this group.
Click Delete Offline Devices to remove the offline device from the list.
37
3.2 Configuring SSID and Wi-Fi Password

(1) Go to the page for configuration.
 Method 1: Choose Network ( WLAN) > Wi-Fi > Wi-Fi Settings. Select the target Wi-Fi.
 Method 2: Choose Network ( WLAN) > Wi-Fi > Wi-Fi List. Select the target Wi-Fi in the list and
click Edit in the action column.
(2) Click the target Wi-Fi network, change the SSID and Wi-Fi password of the Wi-Fi network, and click Save.
Caution
After the configuration is saved, all online clients will be disconnected from the Wi-Fi network. You have to
enter the new password to connect to the Wi-Fi network.
38
3.3 Hiding the SSID
3.3.1 Overview
Hiding the SSID can prevent unauthorized clients from accessing the Wi-Fi network and enhance network
security. After this function is enabled, the mobile phone or PC cannot search out the SSID. Instead, you have
to manually enter the correct SSID and Wi-Fi password. Remember the SSID so that you can enter the correct
SSID after the function is enabled.
(2) Click Expand, turn on Hide SSID in the expanded settings and click Save.
Caution
After the configuration is saved, you have to manually enter the SSID and Wi-Fi password before connecting
any device to the Wi-Fi network. Therefore, exercise caution when performing this operation.
39
3.4 Checking Wireless Clients

RAP6262 models:
If the self-organizing network is disabled, choose WLAN > Clients
If the self-organizing network is enabled, in Network mode, choose Clients > Online Clients > Wireless
For other RAP models:
Choose WLAN > Clients
Check information about all wireless clients connected to the Wi-Fi network. Click Add to Blacklist to disconnect
a client and ban the client from accessing the Wi-Fi network.
40
Table 3-1 Description of Wireless Client Information
Item Description
Username Name of a client
MAC MAC address of the client
IP IPv4 address of the client
SN SN of the device associated with the client
Duration Time when the client connects to the Wi-Fi network
RSSI RSSI of the Wi-Fi network associated with the client
Rate/Negotiation Rate Association rate of the client and AP
Band Band type of the Wi-Fi network, to which the client connects
SSID Name of the Wi-Fi network associated with the client
Channel Channel of the Wi-Fi network associated with the client
Current Rate Uplink and downlink data rate.
41
3.5 Configuring Wi-Fi Band

(2) Set the band of Wi-Fi signals. The device supports the 2.4 GHz and 5 GHz bands. Compared with the 2.4
GHz band, the 5 GHz band supports a higher network transmission rate and is less susceptible to interference,
but is inferior in signal coverage and through-wall penetration. You can select an appropriate signal band
based on actual requirements. The default Wi-Fi band is 2.4G+5G, indicating that Wi-Fi signals are emitted
in both 2.4 GHz and 5 GHz bands.
3.6 Configuring Band Steering
Caution
This function can be enabled only after the dual-band integration (Band is set to 2.4G+5G) is enabled on the
Wi-Fi network. A client automatically selects a band only when the SSIDs of the 2.4 GHz and 5 GHz bands are
the same.
42
(2) Click Expand, turn on Band Steering in the expanded settings, and click Save. After the function is enabled,
the client supporting 5 GHz selects the 5G Wi-Fi network preferentially.
3.7 Configuring Wi-Fi 6
Caution
The function takes effect only on APs supporting the IEEE 802.11ax protocol. In addition, access clients must
support IEEE 802.11ax so that clients can enjoy high-speed Internet access experience brought by Wi-Fi 6. If
clients do not support Wi-Fi 6, you can disable this function.
43
(2) Click Expand, turn on Wi-Fi6 in the expanded settings, and click Save. After this function is enabled, wireless
clients can enjoy faster Internet access service.
3.8 Configuring Layer-3 Roaming

(2) Click Expand, turn on Layer 3 Roaming in the expanded settings and click Save. The client will keep the IP
address unchanged in this Wi-Fi network, improving roaming experience across VLANs.
44
3.9 Configuring AP Isolation

(2) Click Expand, turn on AP Isolation in the expanded settings and click Save. The clients joining in this Wi-Fi
network will be isolated. The clients associated with the same access point cannot access each other.
45
3.10 Adding a Wi-Fi Network

 Method 1: Choose Network ( WLAN) > Wi-Fi > Wi-Fi Settings.
 Method 2: Choose Network ( WLAN) > Wi-Fi > Wi-Fi List.
(2) Click Add, enter the SSID and Wi-Fi password and click OK to add a Wi-Fi network. Click Expand to
configure more Wi-Fi features in the expanded settings. After the Wi-Fi network is added successfully, it will
be displayed in the list. The client will be able to scan the new Wi-Fi network.
46
3.11 Configuring a Guest Wi-Fi
3.11.1 Overview
This Wi-Fi network is provided for guests and is disabled by default. It supports client isolation, that is, access
clients are isolated from each other. They can only access the Internet via Wi-Fi, but cannot access each other,
improving security. The guest Wi-Fi network can be turned off as scheduled. When the time expires, the guest
network is off.
Choose Network ( WLAN) > Wi-Fi > Wi-Fi Settings.
Click Add Guest Wi-Fi to configure the SSID and password of the Guest Wi-Fi. Click Expand to configure the
effective time period and other Wi-Fi features in the expanded settings. Click Save, and the guest Wi-Fi network
will be created. Guests can access the guest Wi-Fi network by entering the SSID and Wi-Fi password.
47
3.12 Configuring Wi-Fi Blacklist or Whitelist
3.12.1 Overview
You can configure the global or SSID-based blacklist and whitelist. The MAC address supports full match and
OUI match.
Wi-Fi blacklist: Clients in the Wi-Fi blacklist are prevented from accessing the Internet. Clients that are not added
to the Wi-Fi blacklist are free to access the Internet.
Wi-Fi whitelist: Only clients in the Wi-Fi whitelist can access the Internet. Clients that are not added to the Wi-Fi
whitelist are prevented from accessing the Internet.
Caution
If the whitelist is empty, the whitelist does not take effect. In this case, all clients are allowed to access the
Internet.
1. Configuring a Global Blacklist/Whitelist
Choose Clients ( WLAN) > Blacklist/Whitelist > Global Blacklist/Whitelist.
Select the blacklist or whitelist mode and click Add to configure a blacklist or whitelist client. In the Add window,
enter the MAC address and remark of the target client and click OK. If a client is already associated with the
access point, its MAC address will pop up automatically. Click the MAC address directly for automatic input. All
clients in the blacklist will be forced offline and not allowed to access the Wi-Fi network. The global blacklist and
whitelist settings take effect on all Wi-Fi networks of the access point.
48
2. Configuring an SSID-based Blacklist/Whitelist
Choose Clients ( WLAN) > Blacklist/Whitelist > SSID-Based Blacklist/Whitelist.
Select a target Wi-Fi network from the left column, select the blacklist or whitelist mode and click Add to configure
a blacklist or whitelist client. The SSID-based blacklist and whitelist will restrict the client access to the specified
Wi-Fi.
49
3.13 Optimizing Wi-Fi Network
3.13.1 Overview
The device detects the surrounding wireless environment and selects the appropriate configuration upon power-
on. However, network stalling caused by wireless environment changes cannot be avoided. You can optimize
the network with one single click, analyze the wireless environment around the access point and select
appropriate parameters.
Caution
After being optimized, the Wi-Fi network will restart, and clients need to reconnect to the W-Fi network.
Therefore, exercise caution when performing this operation.
Install Wi-Fi Moho or other Wi-Fi scanning app on the mobile phone and check interference analysis results to
find out the best channel.
50
3.13.3 Optimizing the Radio Channel

RAP6262 models:
 Configure the master device. Choose Network ( WLAN) > Radio Frequency
 Configure the slave device. Choose Devices > Select the target device in the device list and click SN >
Radio Frequency
 Configure the master device. Choose WLAN > Radio Frequency
 Configure the slave device. Choose WLAN > APs > Select the target device in the device list and click
Manage > WLAN > Radio Frequency
Choose the best channel identified by Wi-Fi Moho or other Wi-Fi scanning App. Click Save to make the
configuration take effect immediately. The more devices in a channel, the greater the interference.
Note
The available channel is related to the country or region code. Select the local country or region.
51
3.13.4 Optimizing the Channel Width
Choose Network ( WLAN) > Radio Frequency.
A network with a lower channel width is more stable, while a network with a higher channel width is susceptible
to interference. If the interference is severe, choose a lower channel width to avoid network stalling to a certain
extent. The access point supports the channel width of 20 MHz and 40 MHz in the 2.4 GHz channel, and the
channel width of 20 MHz and 40 MHz and 80 MHz and 160 MHz in the 5 GHz channel.
The default value is Auto, indicating that the channel width is automatically selected based on the environment.
After changing the channel width, click Save to make the configuration take effect immediately.
Caution
In the self-organizing network mode, the channel width settings will be synchronized to all devices in the
network.
52
3.13.5 Optimizing the Transmit Power

RAP6262 models:
Radio Frequency
A greater transmit power indicates a larger coverage and brings stronger interference to surrounding wireless
routers. In a high-density scenario, you are advised to set the transmit power to a small value. The Auto mode
is recommended, indicating automatic adjustment of the transmit power.
53
3.13.6 Configuring the Kick-off Threshold
In the case of multiple Wi-Fi signals, setting the kick-off threshold can improve the wireless signal quality to a
certain extent. The farther the client is away from the access point, the lower the signal strength is. If the signal
is lower than the kick-off threshold, the Wi-Fi will be disconnected, and the client will be forced offline and select
a nearer Wi-Fi signal.
However, the higher the kick-off threshold is, the easier it is for the client to be kicked offline. To ensure normal
Internet access, you are advised to disable the kick-off threshold or set the value to less than -75dBm.
54
Caution
In the self-organizing network mode, the kick-off threshold settings will be synchronized to all devices in the
network.
3.13.7 Configuring the Client Limit
If the access point is associated with too many clients, it will have a lower performance, affecting user experience.
After you configure the threshold, new clients over the threshold will not be allowed to access the Wi-Fi network.
You can lower the threshold if there is requirement for bandwidth per client. You are advised to keep the default
settings unless there are special cases.
Note
The Client Count Limit refers to the maximum number of clients that can be connected to a single access
point.
3.13.8 Configuring the Roaming Sensitivity

RAP6262 models:
55
Radio Frequency
The roaming sensitivity enables the device to actively disconnect a client from the Wi-Fi network when the client
is far away, forcing the client to re-select the nearest signal and thus improving the sensitivity of wireless roaming.
Higher the roaming sensitivity level, smaller the wireless signal coverage. To improve the signal quality for a
client moving within more than one Wi-Fi coverage, improve the roaming sensitivity level. You are advised to
keep the default settings.
3.13.9 Configuring WIO

RAP6262 models: In Network mode, choose Network >WIO
For other RAP models: Choose WLAN > WIO
Check I have read the notes. And click Network Optimization to optimize the wireless network. You are
advised to set a scheduled task to optimize the wireless network in the early hours of the morning or when the
network is idle.
56
Caution
● WIO is supported only in the self-organizing network mode.

● The client may be offline during the optimization process. The configuration cannot be rolled back once
optimization starts. Therefore, exercise caution when performing this operation.
3.13.10 Configuring Wi-Fi Roaming Optimization (802.11k/v)
Note
The functions mentioned in this chapter are not applicable to such models as RG-RAP1200(F), and RG-
RAP2200(F).

RAP6262 models: In Network mode, choose Network > WIO > Wi-Fi Roaming Optimization (802.11k/v).
For other RAP models: Choose WLAN > WIO > Wi-Fi Roaming Optimization (802.11k/v).
57
Click Enable and the Wi-Fi roaming is further optimized through the 802.11k/v protocol. Smart clients compliant
with 802.11k/v can switch to the APs with better signal and faster speed during the roaming process, ensuring
high-speed wireless connectivity. To ensure smart roaming effect, the WLAN environment will be auto scanned
when Wi-Fi roaming optimization is first enabled.
Caution
● WIO is supported only in the self-organizing network mode.

● During the WLAN environment scanning, the APs will switch channels, forcing the clients to go offline.
The process will last for 2 minutes.
3.14 Configuring Healthy Mode
Choose Network ( WLAN) > Wi-Fi > Healthy Mode.
Select Device Group from the drop-down list box. Click Enable to enable the healthy mode. You are allowed to
set the effective time period for the healthy mode.
58
After the healthy mode is enabled, the transmit power and the Wi-Fi coverage area will decrease. The healthy
mode may reduce signal strength and cause network stalling. You are advised to disable it or enable it when the
network is idle.
3.15 Configuring XPress

(2) Click Expand, turn on XPress in the expanded settings and click Save. After XPress is enabled, the gaming
traffic will be prioritized, ensuring a more stable gaming experience.
59
3.16 Configuring Wireless Schedule

(2) Click Expand, select a scheduled time span to turn on Wi-Fi and click Save. Clients will be allowed to access
the Internet only in the specified time span.
60
3.17 Enabling Reyee Mesh

RAP6262 models: In Network mode, choose Network > Reyee Mesh
For other RAP models: Choose WLAN > APs > Manage > Advanced > Reyee Mesh
After Reyee Mesh is enabled, you can set up a Mesh network through Mesh pairing between the devices that
support Reyee Mesh. You can press the Mesh button on the device to automatically discover a new device for
Mesh pairing or log in to the management page to select a new device for Mesh pairing. Reyee Mesh is enabled
on the device by default.
3.18 Configuring AP Load Balancing
Note
This function is supported by only RG-RAP series access points.
3.18.1 Overview
The AP load balancing function is used to balance the load of APs in the wireless network. When APs are added
to a load balancing group, clients will automatically associate with the APs with light load when the APs in the
group are not load balanced. AP load balancing supports two modes:
 Client Load Balancing: The load is balanced according to the number of associated clients. When a large
number of clients have been associated with an AP and the count difference to the AP with the lightest load
has reached the specified value, the client can only associate with another AP in the group.
 Traffic Load Balancing: The load is balanced according to the traffic on the APs. When the traffic on an AP is
large and the traffic difference to the AP with the lightest load has reached the specified value, the client can
only associate with another AP in the group.
Example: Add AP1 and AP2 into a group and select client load balancing. Set both the client count threshold
and difference to 3. AP1 is associated with 5 clients and AP2 is associated with 2 clients, triggering load
balancing. New clients' attempt to associate to AP1 will be denied, and therefore they can associate only with
AP2.
61
After a client request is denied by an AP and it fails to associate with another AP in the group, the client will keep
trying to associate with this AP. If the client attempts reach the specified value, the AP will permit connection of
this client, ensuring that the user can normally access the Internet.
3.18.2 Configuring Client Load Balancing
Choose Network ( WLAN) > Wi-Fi > Load Balancing.
Click Add. In the dialog box that appears, set Type to Client Load Balancing, and configure Group Name,
Members, and Rule.
Table 3-1 Client load balancing configuration
62
Parameter Description
Group Name Enter the name of the AP load balancing group.
Type Select Client Load Balancing.
Configure a detailed load balancing rule, including the maximum number of

clients allowed to associate with an AP, the difference between the currently
associated client count and client count on the AP with the lightest load, and
the number of attempts to the AP with full load.
Rule By default, when an AP is associated with 3 clients and the difference between
the currently associated client count and client count on the AP with the lightest
load reaches 3, clients can associate only to another AP in the group. After a
client association is denied by an AP for 10 times, the client will be allowed to
associate to the AP upon the next attempt.
Members Specify the APs to be added to the AP load balancing group.
3.18.3 Configuring Traffic Load Balancing
Choose Network ( WLAN) > Wi-Fi > Load Balancing.
Click Add. In the dialog box that appears, set Type to Traffic Load Balancing, and configure Group Name,
Members, and Rule.
63
Table 3-2 Traffic load balancing configuration
Group Name Enter the name of the AP load balancing group.
Type Select Traffic Load Balancing.
Configure a detailed load balancing rule, including the maximum traffic allowed
on an AP, the difference between the current traffic and the traffic on the AP
with the lightest load, and the number of attempts to the AP with full load.
By default, when the traffic load on an AP reaches 500 Kbit/s and the difference
Rule
between the current traffic and the traffic on the AP with the lightest load
reaches 500 Kbit/s, clients can associate only to another AP in the group. After
a client association is denied by an AP for 10 times, the client will be allowed to
associate to the AP upon the next attempt.
Members Specify the APs to be added to the AP load balancing group.
64
Web-based Configuration Guide Network Settings
4 Network Settings
Note
This chapter takes the currently logged in device as an example to describe the entry of each function setting
page. If you need to configure other devices in the network, please refer to the following path to enter the
configuration page of the corresponding device, and then configure the function:
● For RG-RAP2260(G), RG-RAP2260(E), RG-RAP6260(G), RG-RAP6262(G), RG-RAP2260(H), RG-
RAP6262 models: Click Manage Network Device:
● For other RAP models, Choose WLAN > APs > Select the target device in the device list and click
Manage.
4.1 Switching Work Mode
4.1.1 Work Mode
See Work Mode for details.
4.1.2 Self-Organizing Network Discovery
When setting the work mode, you can set whether to enable the self-organizing network discovery function. This
function is enabled by default.
After the self-organizing network discovery function is enabled, the device can be discovered in the network and
discover other devices in the network. Devices network with each other based on the device status and
synchronize global configuration. You can log in to the Web management page of any device in the network to
check information about all devices in the network. After this function is enabled, clients can maintain and
manage the current network more efficiently. You are advised to keep this function enabled.
If the self-organizing network discovery function is disabled, the device will not be discovered in the network and
it runs in standalone mode. After logging in to the Web page, you can configure and manage only the currently
logged in device. If only one device is configured or global configuration does not need to be synchronized to
the device, you can disable the self-organizing network discovery function.
Note
If you need to switch the work mode to wireless bridging mode, please see Wireless Repeater Mode for
details.

RAP6262 models: In Local Device mode, choose Overview > Device Details
65
For other RAP models: Choose ( WLAN > APs > Manage) Overview > Device Details
Click the current work mode to change the work mode.
AC function switch: If a device works in the router mode and the self-organizing network discovery function is
enabled, you can enable or disable the AC function. After the AC function is enabled, the device in the router
mode supports the virtual AC function and can manage downlink devices. If this function is disabled, the device
needs to be elected as an AC in self-organizing network mode and then manage downlink devices.
66
Caution
After the self-organizing network discovery is enabled, you can check the role of the device in self-organizing
network mode.
4.1.4 Viewing Device Role

RAP6262 models: In Local Device mode, choose Overview > Device Details
For other RAP models: Choose ( WLAN > APs > Manage) Overview > Device Details
If the self-organizing network is enabled, you can view the device role on the Device Details page.
Master AP/AC: The device can manage downlink devices.
Slave AP/Device: The device has been managed by an AC. The slave Aps are managed by the master AP/AC
in a unified manner. Some wireless network settings cannot be edited alone, and thus the master AP/AC delivers
configurations to edit the network settings in a unified manner.
4.2 Configuring Internet Type

RAP6262 models: In Local Device mode, choose Network > WAN
For other RAP models: Choose ( WLAN > APs > Manage >) Network > WAN
Select the Internet connection type after confirming with the ISP. For detailed configuration, see Work Mode.
67
4.3 Configuring LAN Port
Caution
This function is not supported when the device works in AP mode.

RAP6262 models: In Local Device mode, choose Network > LAN > LAN Settings
For other RAP models: Choose ( WLAN > APs > Manage >) Network > LAN > LAN Settings
Click Edit. In the displayed dialog box, enter the IP address and subnet mask, and click OK. Change the IP
address of the LAN port. Enter the new IP address in the browser and log in to the device again to configure
and manage the device.
68
4.4 Configuring Repeater Mode
Caution
RG-RAP1200(F) access point does not support this function.
4.4.1 Wired Repeater

RAP6262 models: In Local Device mode, choose Network > Repeater Mode
For other RAP models: Choose ( WLAN > APs > Manage >) Network > Repeater Mode
Connect a network cable from the WAN port (uplink LAN port) of the device to the upper-layer device.
Select Access Point, click Check, confirm the Wi-Fi settings of the AP, and then click Save to expand the
network coverage.
Caution
After the configuration is saved, connected clients will be disconnected from the network for a short period of
time. You can reconnect the clients to the Wi-Fi network for restoration.
69
4.4.2 Wireless Repeater
The wireless repeater mode extends the Wi-Fi coverage range of the primary device. The device supports the
dual-link wireless repeater mode and can extend both 2.4 GHz and 5 GHz signals of the primary device.
Note
● To avoid loops in wireless repeater mode, remove the network cable from the WAN port.
● Obtain the Wi-Fi name and Wi-Fi password of the upper-layer router.

RAP6262 models: In Local Device mode, choose Network > Repeater Mode
For other RAP models: Choose ( WLAN > APs > Manage >) Network > Repeater Mode
(1) Click Wireless Repeater and then click Select. A list of surrounding Wi-Fi signals pops up. A list of nearby 5
GHz Wi-Fi networks is displayed by default. You can switch from 5 GHz to 2.4 GHz band by selecting 2.4G
from the drop-down list box. You are advised to select a strong 5 GHz Wi-Fi network signal.
70
(2) Select the Wi-Fi signal of the upper-layer device that you want to extend. The configuration items of the local
device are displayed. If the signal of the upper-layer device is encrypted, enter the Wi-Fi password of the
upper-layer device.
(3) Configure Local Router Wi-Fi. You can select New Wi-Fi or Same as Primary Router Wi-Fi.
○ If you select Same as Primary Router Wi-Fi, the Wi-Fi settings of the router are automatically
synchronized with those on the primary router. Generally, clients merge Wi-Fi signals with the same
name into one Wi-Fi signal, and they can search out only the Wi-Fi signal of the primary router.
○ If New Wi-Fi is selected, you can set a local Wi-Fi name and password. Clients will search out different
Wi-Fi signals.
71
Caution
● After the configuration is saved, the AP will be disconnected from the Wi-Fi network and needs to connect
to the new Wi-Fi network. Exercise caution when performing this operation. Record the new Wi-Fi name
and password.
● You are advised to install the AP in a position where the RSSI is greater than two bars of signal to prevent
signal loss. If the signal at the installation position is too weak, the Wi-Fi extension may fail or the quality
of extended signal may be poor.
4.5 Creating a VLAN
Caution

72
A LAN can be classified into multiple VLANs. Click Add to create a VLAN.
Table 4-1 VLAN Configuration
IP address of the VLAN interface. The default gateway of devices that access the Internet
IP
through the current LAN should be set to this IP address.
Subnet Mask Subnet mask of the IP address of the VLAN interface.
VLAN ID VLAN ID.
Remark VLAN description.
MAC MAC address of the VLAN interface.
73
Enable the DHCP server function. After it is enabled, devices on the LAN can automatically
obtain IP addresses. After the DHCP service is enabled, you need to configure the start IP
DHCP Server address to be assigned, number of IP addresses to be assigned, and address lease term
for the DHCP server, and other DHCP server options. For details, see Configuring DHCP
Server.
Caution
VLAN configuration is associated with the configuration of the uplink device. Therefore, refer to the
configuration of the uplink device when configuring a VLAN.
4.6 Configuring Port VLAN
Caution
The port VLAN can be configured only when the device works in AP mode.

RAP6262 models: In Local Device mode, choose Network > LAN
For other RAP models: Choose ( WLAN > APs > Manage >) Network > LAN
(1) On the LAN Settings tab page, turn on Port VLAN, and click OK in the confirmation dialog box.
(2) Click Add. Enter the VLAN ID and description, and click OK to create a VLAN. The added VLAN is used to
set the VLAN, to which a port belongs.
74
(3) Switch to the Port VLAN tab page and configure VLANs for the port. Click the option box below the port,
select the mapping between a VLAN and the port from the drop-down list box, and click Save.
○ UNTAG: Configure the VLAN as the native VLAN of the port. That is, when receiving a packet from this
VLAN, the port removes the VLAN tag from the packet and forwards the packet. When receiving an
untagged packet, the port adds the VLAN tag to the packet and forwards the packet through the VLAN.
Only one VLAN can be configured as an untagged VLAN on each port.
○ TAG: Configure the VLAN as an allowed VLAN of the port, but the VLAN cannot be the native VLAN.
That is, VLAN packets carry the original VLAN tag when they are forwarded by the port.
○ Not Join: Configure the port not to allow packets from this VLAN to pass through. For example, if VLAN
10 and VLAN 20 are not added to port 2, port 2 will neither receive nor send packets from or to VLAN 10
and VLAN 20.
75
4.7 Changing MAC Address

ISPs may restrict the access of devices with unknown MAC addresses to the Internet for the sake of security. In
this case, you can change the MAC address of the WAN port.
Click to expand Advanced Settings, enter the MAC address, and click Save. You do not need to change the
default MAC address unless in special cases.
In the router mode, change the MAC address of the LAN port on Network > LAN.
Caution
Changing the MAC address will disconnect the device from the network. You need to reconnect the device to
the network or restart the device. Therefore, exercise caution when performing this operation.
76
4.8 Changing MTU

WAN interface MTU indicates the maximum transmission unit (MTU) allowed by the WAN interface. The default
value is 1500 bytes, indicating the maximum data forwarding efficiency. Sometimes, ISP networks restrict the
speed of large data packets or forbid large data packets from passing through. As a result, the network speed
is unsatisfactory or even the network is disconnected. In this case, you can set the MTU value to a smaller value.
4.9 Configuring DHCP Server
Caution
4.9.1 DHCP Server
In the router mode, the DHCP server function can be enabled on the device to automatically assign IP addresses
to clients so that clients connected to the LAN ports or Wi-Fi network of the device obtain IP addresses for
Internet access.
4.9.2 Configuring the DHCP Server Function

77
DHCP Server: The DHCP server function is enabled by default in the router mode. You are advised to enable
the function if the device is used as the sole router in the network. When multiple routers are connected to the
upper-layer device through LAN ports, disable this function.
Caution
If the DHCP server function is disabled on all devices in the network, clients cannot automatically obtain IP
addresses. You need to enable the DHCP server function on one device or manually configure a static IP
address for each client for Internet access.
Start: Enter the start IP address of the DHCP address pool. A client obtains an IP address from the address
pool. If all the addresses in the address pool are used up, no IP address can be obtained from the address pool.
IP Count: Enter the number IP addresses in the address pool.
Lease Time(Min): Enter the address lease term. When a client is connected, the leased IP address is
automatically renewed. If a leased IP address is not renewed due to client disconnection or network instability,
the IP address will be reclaimed after the lease term expires. After the client connection is restored, the client
can request an IP address again. The default lease term is 30 minutes.
78
4.9.3 Displaying Online DHCP Clients

RAP6262 models: In Local Device mode, choose Network > LAN >DHCP Clients
For other RAP models: Choose ( WLAN > APs > Manage >) Network > LAN > DHCP Clients
Check information about an online client. Click Convert to Static IP. Then, the static IP address will be obtained
each time the client connects to the network.
4.9.4 Displaying the DHCP Static IP Address List

RAP6262 models: In Local Device mode, choose Network > LAN > Static IP Addresses
For other RAP models: Choose ( WLAN > APs > Manage >) Network > LAN > Static IP Addresses
Click Add. In the displayed static IP address binding dialog box, enter the MAC address and IP address of the
client to be bound, and click OK. After a static IP address is bound, the bound IP address will be obtained each
time the client connects to the network.
79
4.10 Link Aggregation
Caution
The function is supported by only RG-RAP2260(H).
In Local Device mode, choose Advanced > Link Aggregation.
Link Aggregation can improve the throughput in the network and deal with link congestion.
4.11 Configuring DNS

RAP6262 models: In Local Device mode, choose Advanced > Local DNS
80
For other RAP models: Choose ( WLAN > APs > Manage >) Advanced > Local DNS
Enter the IP address of the DNS server and click Save. The local DNS server is optional. The device obtains
the DNS server address from the connected uplink device by default. The default configuration is recommended.
The available DNS service varies from region to region. You can consult the local ISP.
4.12 Hardware Acceleration
Note
The functions mentioned in this chapter are only applicable to such models as RAP2260(H), RAP6260(H),
RAP6260(H)-D, RG-RAP1261, RG-RAP2266, RAP2260, RG-RAP1260 and RAP6262.
In Local Device mode, choose Advanced > Hardware Acceleration.
After Hardware acceleration is enabled, the Internet access speed will be improved.
4.13 Configuring Port Flow Control

RAP6262 models: In Local Device mode, choose Advanced > Port Settings
For other RAP models: Choose ( WLAN > APs > Manage >) Advanced > Port Settings
When the LAN ports work at different rates, data congestion may occur, which can slow down the network speed
and affect the Internet access experience. Enabling port flow control can help mitigate this problem.
81
4.14 Configuring ARP Binding
Caution
The device learns the IP and MAC addresses of network devices connected to ports of the device and generates
ARP entries. You can bind ARP mappings to improve network security.

RAP6262 models: In Local Device mode, choose Security > ARP List
For other RAP models: Choose ( WLAN > APs > Manage >) Security > ARP List
ARP mappings can be bound in two ways:
(1) Select a dynamic ARP entry in the ARP list and click Bind. You can select multiple entries to be bound at
one time and click Bind Selected to bind them. To remove the binding between a static IP address and a
MAC address, click Delete in the Action column.
(2) Click Add, enter the IP address and MAC address to be bound, and click OK. The input box can display
existing address mappings in the ARP list. You can click a mapping to automatically enter the address
mapping.
82
4.15 Configuring LAN Ports
Caution
The configuration takes effect only on APs having wired LAN ports.
Choose Network ( WLAN) > LAN Ports.
Enter the VLAN ID and click Save to configure the VLAN, to which the AP wired ports belong. If the VLAN ID is
null, the wired ports and WAN port belong to the same VLAN.
In self-organizing network mode, the AP wired port configuration applies to all APs having wired LAN ports on
the current network. The configuration applied to APs in LAN Port Settings takes effect preferentially. Click Add
to add the AP wired port configuration. For APs, to which no configuration is applied in LAN Port Settings, the
default configuration of the AP wired ports will take effect on them.
83
84
Web-based Configuration Guide System Settings
5 System Settings
5.1 PoE
Caution
Only RG-RAP1200(P) supports this function.
Choose Wireless > APs > Manage > Basics > PoE.
The device supplies power to PoE powered devices through ports. You can check the total power, current
consumption, remaining consumption, and whether PoE power supply status is normal. Move the cursor over a
port. The power switch icon appears. You can click it to control whether to enable PoE on the port.
5.2 PoE Settings
Caution
This function is supported by only RG-RAP2260(G), RG-RAP2260(E), RG-RAP6260(G), RG-RAP6262(G),

RG-RAP2260(H), RG-RAP6260(H), RG-RAP6260(H)-D, RG-RAP1261, RG-RAP2266, RG-RAP2260, RG-
RAP1260 and RG-RAP6262.
In Local Device mode, choose Advanced > PoE Settings.
Set the power mode for the AP to accept power over PoE. In AF mode, the maximum power supported by the
device is 15.4 W. In AT mode, the maximum power is 30 W according to the IEEE 802.3at standard. In BT mode,
the maximum power is 51 W according to the IEEE 802.3bt standard. By default, the device automatically
85
negotiates with the power sourcing equipment (PSE) about the power mode. The default configuration is
recommended.
5.3 Setting the Login Password

RAP6262 models:
If the device works in self-organizing network mode, and Network mode webpage is displayed, choose
System > Login Password
In standalone mode: Choose System > Login > Login Password
In self-organizing network mode: Choose Network > Password
In standalone mode: Choose System > Login > Login Password
Enter the old password and new password. After saving the configuration, use the new password to log in.
Caution
In self-organizing network mode, the login password of all devices in the network will be changed
synchronously.
86
5.4 Setting the Session Timeout Duration

RAP6262 models:
If the device works in self-organizing network mode, and Local Device mode webpage is displayed, choose
System > Login
In standalone mode: Choose System > Login > Session Timeout
In self-organizing network mode: Choose WLAN > APs > Manage > System > Login > Session Timeout
In standalone mode: Choose System > Login > Session Timeout
If no operation is performed on the Web page within a period of time, the session is automatically disconnected.
When you need to perform operations again, enter the password to log in again. The default timeout duration is
3600 seconds, that is, 1 hour.
5.5 Setting and Displaying System Time

RAP6262 models:
87
If the device works in self-organizing network mode, and Network mode webpage is displayed, choose
System > System Time
In standalone mode: Choose System > System Time
In self-organizing network mode: Choose Network > Time
In standalone mode: Choose System > System Time
You can view the current system time. If the time is incorrect, check and select the local time zone. If the time
zone is correct but time is still incorrect, click Edit to manually set the time. In addition, the device supports
Network Time Protocol (NTP) servers. By default, multiple servers serve as the backup of each other. You can
add or delete the local server.
Caution
In self-organizing network mode, the system time of all devices in the network will be changed synchronously.
88
5.6 Configuring Reboot
Caution
● Do not cut off power during system reboot to avoid device damage.
● Do not refresh the page or close the browser during the reboot. After the device is successfully rebooted
and the Web service becomes available, the device automatically jumps to the login page.
● Rebooting the device affects the network. Therefore, exercise caution when performing this operation.
5.6.1 Rebooting the Current Device

RAP6262 models: In Local Device mode, choose System > Reboot > Reboot
In self-organizing network mode: Choose WLAN > APs > Reboot
In standalone mode: Choose System > Reboot > Reboot
Click Reboot. The device will restart.
5.6.2 Rebooting All Devices in the Network
In self-organizing network mode, you can reboot all devices in the network in batches.

RAP6262 models: In Network mode, choose System > Reboot > Reboot
For other RAP models: Choose Network > Reboot & Reset > Reboot
Click Reboot, select All Devices, and click Reboot All Device to reboot all devices in the current network.
89
Caution
It takes time to reboot all devices in the current network. The action may affect the whole network. Please be
cautious.
5.6.3 Rebooting the Specified Device
In self-organizing network mode, you can reboot specified devices in the network in batches.

RAP6262 models: In Network mode, choose System > Reboot > Reboot
For other RAP models: Network > Reboot & Reset > Reboot
Click Reboot, click Specified Devices, select required devices from the Available Devices list, and click Add
to add devices to the Selected Devices on the right. Click Reboot. Specified devices in the Selected Devices
list will be rebooted.
90
5.7 Configuring Scheduled Reboot
5.7.1 Configuring Scheduled Reboot for the Current Device
Confirm that the system time is accurate to avoid network interruption caused by device reboot at wrong time.
For details about how to configure the system time, see Setting the Session Timeout Duration.
91

RAP6262 models: Choose System > Reboot > Scheduled Reboot
To configure scheduled reboot for the current device, choose ( WLAN > APs > Manage >) System >
Reboot > Scheduled Reboot
To configure scheduled reboot for all devices in the network, choose Network>> Scheduled Reboot
Caution
If you configure scheduled reboot on the management webpage, all devices will restart when the system time
matches with the scheduled reboot time. Please be cautious.
Click Enable, and select the date and time of scheduled reboot every week. Click Save. When the system time
matches with the scheduled reboot time, the device will restart. You are recommended to set scheduled reboot
time to off-peak hours.
5.8 Configuring Backup and Import

RAP6262 models: Choose System > Management > Backup & Import
For other RAP models: Choose ( WLAN > APs > Manage >) System > Management > Backup &
Import
Configuration backup: Click Backup to download a configuration file locally.
92
Configuration import: Click Browse, select a backup file on the local PC, and click Import to import the
configuration file. The device will restart.
5.9 Restoring Factory Settings
5.9.1 Restoring the Current Device to Factory Settings

RAP6262 models: In Local Device mode, choose System > Management > Reset
For other RAP models: Choose ( WLAN > APs > Manage >) System > Management > Reset
Click Reset to restore the current device to the factory settings.
Caution
The operation will clear all configuration of the current device. If you want to retain the current configuration,
back up the configuration first (See Configuring Backup and Import). Therefore, exercise caution when
performing this operation.
93
5.9.2 Restoring All Devices to Factory Settings
In the self-organizing network mode, all devices in the network will be restored to factory settings.

RAP6262 models: In Network mode, choose System > Management > Reset
For other RAP models: Choose Network > Reboot & Reset > Restore
Click All Devices, select whether to enable Unbind Account and Click Reset All Devices. All devices in the
network will be restored to factory settings.
Caution
The operation will clear all configuration of all devices in the network. Therefore, exercise caution when
performing this operation.
5.10 Performing Upgrade and Checking System Version
Caution
● You are advised to back up the configuration before upgrading the access point.
● After being upgraded, the access point will reboot. Therefore, exercise caution when performing this
operation.
5.10.1 Online Upgrade

RAP6262 models: In Local Device mode, choose System > Upgrade > Online Upgrade
For other RAP models: Choose ( WLAN > APs > Manage >) System > Upgrade > Online Upgrade
You can view the current system version. If there is a new version available, you can click it for an update.
94
5.10.2 Local Upgrade

RAP6262 models: In Local Device mode, choose System > Upgrade > Local Upgrade
For other RAP models: Choose ( WLAN > APs > Manage >) System > Upgrade > Local Upgrade
You can view the current software version, hardware version and device model. If you want to upgrade the
device with the configuration retained, check Keep Setup. Click Browse, select an upgrade package on the
local PC, and click Upload to upload the file. The device will be upgraded.
5.11 Switching System Language
Choose in the upper right corner of the Web page.
95
Click a required language to switch the system language.
5.12 Configuring LED Status Control
Caution
The LED Status Control function is not supported in the standalone mode (self-organizing network is not
enabled).

RAP6262 models: Choose Network > LED
For other RAP models: Choose WLAN > LED
Turn on the LED of all downlink access points in the network.
96
Web-based Configuration Guide Network Diagnosis Tools
6 Network Diagnosis Tools

6.1 Network Check
When a network error occurs, perform Network Check to identify the fault and take the suggested action.
(1) Click in the navigation bar, or choose Diagnostics > Network Check and go to the Network Check
page.
(2) Click Start to perform the network check and show the result.
97
After performing the network check, you will find the check result and suggested action.
6.2 Network Tools

RAP6262 models: In Local Device mode, choose Diagnostics > Network Tools
For other RAP models: Choose ( WLAN > APs > Manage >) Diagnostics > Network Tools
When you select the ping tool, you can enter the IP address or URL and click Start to test the connectivity
between the access point and the IP address or URL. The message "Ping failed" indicates that the access point
cannot reach the IP address or URL.
The Traceroute tool displays the network path to a specific IP address or URL.
The DNS Lookup tool displays the DNS server address used to resolve a URL.
98
6.3 Alarms
RAP6262 models: In Network mode, choose Network > Alarms
For other RAP models: Choose ( WLAN > APs > Manage >) Diagnostics > Alarms
The Alarms page displays possible problems on the network environment and device. All types of alarms are
followed by default. You can click Unfollow in the Action column to unfollow this type of alarm.
Caution
After unfollowing a type of alarm, you will not discover and process all alarms of this type promptly. Therefore,
exercise caution when performing this operation.
99
Click View Unfollowed Alarm to view the unfollowed alarm. You can follow the alarm again in the pop-up
window.
6.4 Fault Collection

RAP6262 models: In Local Device mode, choose Diagnostics > Fault Collection
100
For RAP models: Choose ( WLAN > APs > Manage >) Diagnostics > Fault Collection
When an unknown fault occurs on the device, you can collect fault information on this page. Click Start to collect
fault information and compress it into a file for engineers to identify fault.
101
Web-based Configuration Guide FAQs
7 FAQs
7.1 Login Failure
 What can I do when I failed to log in to the Eweb management system?
Perform the following steps:
(1) Check that the Ethernet cable is properly connected to the LAN port of the device.
(2) Before accessing the setup page, you are advised to choose Auto for the device enabled with DHCP service
to assign an IP address to the PC. If you want to configure a static IP address for the PC, please make sure
the IP address of the PC and the LAN port are in the same IP range. The default IP address of the LAN port
is 10.44.77.254, and the subnet mask is 255.255.255.0. The IP address of the PC should be set to 10.44.77.X
(X is an integer between 2 and 254), and the subnet mask is 255.255.255.0.
(3) Run the Ping command to check the connectivity between the PC and the device. If the ping fails, please
check the network settings.
(4) If the login failure persists, restore the device to factory settings.
7.2 Factory Setting Restoration

 How can I restore the device to factory settings?
Power on the device and press the Reset button for more than 5 seconds. The device is restored to factory
settings after it is restarted. Then, you can log in to the Eweb management system using the default IP address
(10.44.77.254).
7.3 Password Loss

 What can I do when I forget the password?
 Webpage management password loss: Please enter the Wi-Fi password. If it is still incorrect, please restore
the device to factory settings.
 Wi-Fi password loss: When the access point expands the Wi-Fi coverage, its Wi-Fi password is consistent
with that of the master router. Please check the configuration of the master router and enter its Wi-Fi
password. If the password is still incorrect, please restore the device to factory settings and reconfigure the
Wi-Fi password.
102

Ruijie Reyee RG-RAP Series Access Points Web-Based Configuration Guide, Release ReyeeOS 1.210 (V1.2)

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Ruijie Reyee RG-RAP Series Access Points Web-Based Configuration Guide, Release ReyeeOS 1.210 (V1.2)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ruijie Reyee RG-RAP Series Access Points Web-Based Configuration Guide, Release ReyeeOS 1.210 (V1.2)

Uploaded by

Copyright:

Available Formats

Ruijie Reyee RG-RAP Series Access

Web-based Configuration Guide

Document Version: V1.2

All rights are reserved in this document and this statement.

Trademarks including , are owned by Ruijie Networks.

 Technical support and servicing engineers

 Technical support website: https://ruijienetworks.com/support

 Case portal: https://caseportal.ruijienetworks.com

 Technical support Email: [email protected]

> Multi-level menus items Select System > Time.

An alert that contains a description of product or version support.

1 Fast Internet Access.......................................................................................................................... 1

1.1 Configuration Environment Requirements ................................................................................ 1

1.2 Default Configuration ................................................................................................................. 1

1.3 Login to Eweb ............................................................................................................................ 1

1.3.1 Connecting to the Access Point ..................................................................................... 1

1.3.2 Configuring the IP Address of the Management Client ................................................. 2

1.3.3 Logging in to the Web Page .......................................................................................... 2

1.4 Work Mode ................................................................................................................................. 3

1.4.1 AP Mode ......................................................................................................................... 3

1.4.2 Router Mode .................................................................................................................. 3

1.4.3 Wireless Repeater Mode ............................................................................................... 3

1.5 Configuration Wizard (Router Mode) ......................................................................................... 4

1.5.1 Getting Started ............................................................................................................... 4

1.5.2 Configuration Steps ....................................................................................................... 5

1.6 Configuration Wizard (AP Mode) ............................................................................................... 7

1.6.1 Getting Started ............................................................................................................... 7

1.6.2 Configuration Steps ....................................................................................................... 7

1.7 Configuration Wizard (Wireless Repeater Mode) ...................................................................... 8

1.7.1 Getting Started ............................................................................................................... 8

1.7.2 Configuration Steps ....................................................................................................... 8

1.8 Introduction to the Eweb GUI................................................................................................... 10

1.8.2 Dual Management Webpages ..................................................................................... 12

2 Network Monitoring ......................................................................................................................... 15

2.1 Viewing the Network Information ............................................................................................. 15

2.2 Adding Network Devices.......................................................................................................... 17

2.2.1 Wired Connection ........................................................................................................ 17

2.2.2 AP Mesh ....................................................................................................................... 19

2.3 Managing Network Devices ..................................................................................................... 28

2.4 Configuring Network Planning ................................................................................................. 30

2.4.1 Configuring Wired VLAN .............................................................................................. 30

2.4.2 Configuring Wi-Fi VLAN ............................................................................................... 32

2.5 Troubleshooting Fault Alerts .................................................................................................... 34

3 Wi-Fi Network Settings.................................................................................................................... 36

3.1 Configuring AP Groups ............................................................................................................ 36

3.1.1 Overview ...................................................................................................................... 36

3.1.2 Procedures ................................................................................................................... 36

3.2 Configuring SSID and Wi-Fi Password ................................................................................... 38

3.3 Hiding the SSID ....................................................................................................................... 39

3.3.1 Overview ...................................................................................................................... 39

3.3.2 Configuration Steps ..................................................................................................... 39

3.4 Checking Wireless Clients ....................................................................................................... 40

3.5 Configuring Wi-Fi Band............................................................................................................ 42

3.6 Configuring Band Steering....................................................................................................... 42

3.7 Configuring Wi-Fi 6 .................................................................................................................. 43

3.9 Configuring AP Isolation .......................................................................................................... 45

3.10 Adding a Wi-Fi Network ......................................................................................................... 46