US2882

Bipolar Hall Switch – Very High Sensitivity

Features and Benefits Applications

 Wide operating voltage range from 3.5V to 24V  Automotive, Consumer and Industrial
 Very high magnetic sensitivity  Solid-state switch
 CMOS technology  Brushless DC motor commutation
 Chopper-stabilized amplifier stage  Speed detection
 Low current consumption  Linear position detection
 Open drain output  Angular position detection
 AEC-Q100 Qualified  Proximity detection
 Thin SOT23 3L and flat TO-92 3L
 both RoHS Compliant packages

Ordering information
Product code Temperature Code Package Code Option code Packing form code
US2882 E SE AAA-000 RE
US2882 E UA AAA-000 BU
US2882 K SE AAA-000 RE
US2882 K UA AAA-000 BU
US2882 L SE AAA-000 RE
US2882 L UA AAA-000 BU

Legend:
Temperature code: L(-40 to 150°C)
E(-40 to 85°C)
K (-40 to 125°C)
Package Code: SE = TSOT-23L
UA = TO92-3L
Packing Form: BU = Bulk
RE = Reel
Ordering Example: US2882ESE-AAA-000-RE
1. Functional Diagram 2. General Description
The Melexis US2882 is a bipolar Hall-effect switch designed
in mixed signal CMOS technology.

The device integrates a voltage regulator, Hall sensor with

dynamic offset cancellation system, Schmitt trigger and an
open-drain output driver, all in a single package.

Thanks to its wide operating voltage range and extended

choice of temperature range, it is suitable for use in
automotive and consumer applications.

The device is delivered in a Thin Small Outline Transistor

(TSOT) for surface mount process and in a Plastic Single In
Line (TO-92 flat) for through- hole mount.
Both 3-lead packages are RoHS compliant.

REVISION 006 – 13 JUNE 2019 Page 1 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

Contents
1. Functional Diagram .............................................................................................................................................. 1
2. General Description.............................................................................................................................................. 1
3. Glossary of Terms ................................................................................................................................................. 3
4. Absolute Maximum Ratings .................................................................................................................................. 3
5. Pin Definitions and Descriptions ........................................................................................................................... 3
6. General Electrical Specifications ........................................................................................................................... 4
7. Magnetic Specifications........................................................................................................................................ 4
8. Output Behaviour versus Magnetic Pole............................................................................................................... 4
9. Detailed General Description................................................................................................................................ 5
10. Unique Features ................................................................................................................................................. 5
11. Performance Graphs .......................................................................................................................................... 6
11.1. Magnetic parameters vs. TA ...................................................................................................................... 6
11.2. Magnetic parameters vs. VDD.................................................................................................................... 6
11.3. VDSon vs. TA ............................................................................................................................................. 6
11.4. VDSon vs. VDD........................................................................................................................................... 6
11.5. IDD vs. TA .................................................................................................................................................. 6
11.6. IDD vs. VDD ............................................................................................................................................... 6
11.7. IOFF vs. TA................................................................................................................................................. 7
11.8. IOFF vs. VDD .................................................................................................................................................. 7
12. Test Conditions .................................................................................................................................................. 7
12.1. Supply Current ........................................................................................................................................... 7
12.2. Output Saturation Voltage ........................................................................................................................ 7
12.3. Output Leakage Current ............................................................................................................................ 7
12.4. Magnetic Thresholds ................................................................................................................................. 7
13. Application Information...................................................................................................................................... 8
13.1. Typical Three-Wire Application Circuit ...................................................................................................... 8
13.2. Two-Wire Circuit........................................................................................................................................ 8
13.3. Automotive and Harsh, Noisy Environments Three-Wire Circuit............................................................... 8
14. Application Comments ....................................................................................................................................... 8
15. Standard information regarding manufacturability of Melexis products with different soldering processes ...... 9
16. ESD Precautions ................................................................................................................................................. 9
17. Package Information ........................................................................................................................................ 10
17.1. SE Package (TSOT-3L) .............................................................................................................................. 10
17.2. UA Package (TO-92 flat) ........................................................................................................................... 11
18. Contact............................................................................................................................................................. 12
19. Disclaimer ........................................................................................................................................................ 12

REVISION 006 – 13 JUNE 2019 Page 2 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

3. Glossary of Terms

MilliTesla (mT), Gauss Units of magnetic flux density:

1mT = 10 Gauss
RoHS Restriction of Hazardous Substances
TSOT Thin Small Outline Transistor (TSOT package) – also referred with the Melexis package
code “SE”
ESD Electro-Static Discharge
BLDC Brush-Less Direct-Current

4. Absolute Maximum Ratings

Parameter Symbol Value Units
Units
Supply Voltage VDD 28 V
Supply Current IDD 50 mA
Output Voltage VOUT 28 V
Output Current IOUT 50 mA
Storage Temperature Range TS -50 to 150 °C
Maximum Junction Temperature TJ 165 °C
Table 1: Absolute maximum ratings

Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximum- rated
conditions for extended periods may affect device reliability.

Operating Temperature Range Symbol Value Units

Temperature Suffix “E” TA -40 to 85 °C
Temperature Suffix “L” TA -40 to 150 °C

5. Pin Definitions and Descriptions

SE Pin No UA Pin No Name Type Function
1 1 VDD Supply Supply Voltage pin
2 3 OUT Output Open Drain Output pin
3 2 GND Ground Ground pin
Table 2: Pin definitions and descriptions

SE package UA package

REVISION 006 – 13 JUNE 2019 Page 3 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

6. General Electrical Specifications

o
DC Operating Parameters TA = 25 C, VDD = 3.5V to 24V (unless otherwise specified)
Parameter Symbol Test Conditions Min Typ Max Units
Supply Voltage VDD Operating 3.5 12 24 V
Supply Current IDD B < BRP 1.1 2.6 5 mA
Output Saturation Voltage VDSon IOUT = 20mA, B > BOP 0.11 0.5 V
Output Leakage Current IOFF B < BRP, VOUT = 24V 0.01 10 µA
Output Rise Time tr RL = 1kΩ, CL = 20pF 0.25 µs
Output Fall Time tf RL = 1kΩ, CL = 20pF 0.25 µs
Maximum Switching Frequency FSW 10 kHz
SE Package Thermal Resistance RTH Single layer (1S) Jedec board 301 °C/W
UA Package Thermal Resistance RTH 200 °C/W
Table 3: Electrical specifications

7. Magnetic Specifications
DC Operating Parameters VDD = 3.5V to 24V (unless otherwise specified)
Parameter Symbol Test Conditions Min Typ Max Units
Operating Point BOP -3 6 mT
Release Point BRP E spec. (TA max = 85°C) -6 3 mT
Hysteresis BHYST 1.5 6 mT
Operating Point BOP -3.5 6 mT
Release Point BRP L spec. (TA max = 150°C) -6 3.5 mT
Hysteresis BHYST 1.5 6 mT

Table 4: Magnetic specifications

Note: For typical values, please refer to the performance graphs in section 11

8. Output Behaviour versus Magnetic Pole

DC Operating Parameters TA = -40 C to 150 C, VDD = 3.5V to 24V (unless otherwise specified)
Parameter Test Conditions (SE) OUT (SE) Test Conditions (UA) OUT(UA)
South pole B < BRP High B > BOP Low
North pole B > BOP Low B < BRP High

Table 5: Output behaviour versus magnetic pole

South pole North pole

North pole South pole

OUT = high OUT = low (VDSon) OUT = high OUT = low (VDSon)
SE package UA package

REVISION 006 – 13 JUNE 2019 Page 4 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

9. Detailed General Description

Based on mixed signal CMOS technology, Melexis US2882 is a Hall-effect device with very high magnetic sensitivity.
It allows using generic magnets, weak magnets or larger air gap.

The chopper-stabilized amplifier uses switched capacitor technique to suppress the offset generally observed with Hall
sensors and amplifiers. The CMOS technology makes this advanced technique possible and contributes to smaller chip
size and lower current consumption than bipolar technology. The small chip size is also an important factor to minimize
the effect of physical stress.
This combination results in more stable magnetic characteristics and enables faster and more precise design.

The wide operating voltage from 3.5V to 24V, “L” and “E” operating temperature range and low current
consumption make this device especially suitable for automotive and BLDC motor applications.

The output signal is open-drain type. Such output allows simple connectivity with TTL or CMOS logic by using a pull-up
resistor tied between a pull-up voltage and the device output.

10. Unique Features

The US2882 exhibits bipolar magnetic switching characteristics. Therefore, it operates with both south and north
poles.

Typically, the device behaves as a latch with symmetric operating and

release switching points (BOP=|BRP|). This means magnetic fields with
equivalent strength and opposite direction drive the output high and
low.

Removing the magnetic field (B→0) keeps the output in its

previous state. This latching property defines the device as a
magnetic memory.
BRp 0mT Bop

Depending on the magnetic switching points, the device may also behave as a unipolar positive switch (BOP and BRP
strictly positive) or negative switch (BOP and BRP strictly negative). That is the output can be set high and low by only
using one magnetic pole. In such case, removing the magnetic field changes the output level.

BRp max Bop max BRp min Bop min

In latch, positive or negative switch behaviour, a magnetic hysteresis BHYST keeps BOP and BRP separated by a minimal
value. This hysteresis prevents output oscillation near the switching point.

REVISION 006 – 13 JUNE 2019 Page 5 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

11. Performance Graphs

11.1. Magnetic parameters vs. TA 11.2. Magnetic parameters vs. VDD

6 6
Bop, VDD=5V Brp, VDD=5V Bop, Ta=25°C Brp, Ta=25°C
Bop, VDD=12V Brp, VDD=12V Bop, Ta=85°C Bop, Ta=85°C
4 Bop, VDD=24V Brp, VDD=24V 4 Bop, Ta=150°C Brp, Ta=150°C

2 2
Magnetic field (mT)

Magnetic field (mT)

0 0

-2 -2

-4 -4

-6 -6
-40 -20 0 20 40 60 80 100 120 140 0 5 10 15 20
Ta (°C) VDD (Volts)

11.3. VDSon vs. TA 11.4. VDSon vs. VDD

0.5 0.5

Ta=-40°C

Ta=25°C
0.4 0.4
Ta=85°C
VDD=5V
Ta=150°C
VDD=12V
VDSon (Volts)

VDSon (Volts)

0.3 0.3
VDD=24V

0.2 0.2

0.1 0.1

0 0
-40 -20 0 20 40 60 80 100 120 140 0 5 10 15 20
Ta (°C) VDD (Volts)

11.5. IDD vs. TA 11.6. IDD vs. VDD

6 6
Ta=-40°C
Ta=25°C
5 5
VDD=5V Ta=85°C
VDD=12V Ta=150°C
4 4
VDD=24V
IDD (mA)

IDD (mA)

3 3

2 2

1 1

0 0
-40 -20 0 20 40 60 80 100 120 140 0 5 10 15 20
Ta (°C) VDD (Volts)

REVISION 006 – 13 JUNE 2019 Page 6 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

11.7. IOFF vs. TA 11.8. IOFF vs. VDD

30 30

25 25
VDD=5V
Ta=-40°C

VDD=12V Ta=25°C
20 20
Ta=85°C
VDD=24V
Ioff (uA)

Ioff (uA)
Ta=150°C
15 15

10 10

5 5

0 0
-40 -20 0 20 40 60 80 100 120 140 0 5 10 15 20
Ta (°C) VDD (Volts)

12. Test Conditions

Note : DUT = Device Under Test

12.1. Supply Current 12.2. Output Saturation Voltage

12.3. Output Leakage Current

12.4. Magnetic Thresholds

REVISION 006 – 13 JUNE 2019 Page 7 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

13. Application Information

13.1. Typical Three-Wire Application Circuit 13.2. Two-Wire Circuit

13.3. Automotive and Harsh, Noisy Environments

Three-Wire Circuit

14. Application Comments

For proper operation, a 100nF bypass capacitor should be placed as close as possible to the device between the VDD and
ground pin.

For reverse voltage protection, it is recommended to connect a resistor or a diode in series with the VDD pin. When
using a resistor, three points are important:
- the resistor has to limit the reverse current to 50mA maximum (VCC / R1 ≤ 50mA)
- the resulting device supply voltage VDD has to be higher than VDD min (VDD = VCC – R1.IDD)
- the resistor has to withstand the power dissipated in reverse voltage condition (PD = VCC2 / R1)
When using a diode, a reverse current cannot flow and the voltage drop is almost constant (≈0.7V).
Therefore, a 100Ω/0.25W resistor for 5V application and a diode for higher supply voltage are recommended. Both
solutions provide the required reverse voltage protection.

When a weak power supply is used or when the device is intended to be used in noisy environment, it is
recommended that figure 13.3 from the Application Information section is used.
The low-pass filter formed by R1 and C1 and the zener diode Z1 bypass the disturbances or voltage spikes occurring
on the device supply voltage VDD. The diode D1 provides additional reverse voltage protection.

REVISION 006 – 13 JUNE 2019 Page 8 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

15. Standard information regarding manufacturability of Melexis products

with different soldering processes
Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity level
according to following test methods:

Reflow Soldering SMD’s (Surface Mount Devices)

 IPC/JEDEC J-STD-020
Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices
(classification reflow profiles according to table 5-2)
 EIA/JEDEC JESD22-A113
Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing
(reflow profiles according to table 2)

Wave Soldering SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)

 EN60749-20
Resistance of plastic- encapsulated SMD’s to combined effect of moisture and soldering heat
 EIA/JEDEC JESD22-B106 and EN60749-15
Resistance to soldering temperature for through-hole mounted devices

Iron Soldering THD’s (Through Hole Devices)

 EN60749-15
Resistance to soldering temperature for through-hole mounted devices

Solderability SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)

 EIA/JEDEC JESD22-B102 and EN60749-21

Solderability

For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature,
temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with
Melexis.

The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of adhesive
strength between device and board.

Melexis is contributing to global environmental conservation by promoting lead free solutions. For more information on
qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of the use of certain Hazardous
Substances) please visit the quality page on our website: http://www.melexis.com/quality.aspx

16. ESD Precautions

Electronic semiconductor products are sensitive to Electro Static Discharge (ESD).
Always observe Electro Static Discharge control procedures whenever handling semiconductor products.

REVISION 006 – 13 JUNE 2019 Page 9 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

17. Package Information

17.1. SE Package (TSOT-3L)

Notes:

1. Dimension “D” and “E1” do not include

mold flash or protrusions. Mold flash or
protrusion shall not exceed 0.15mm on
“D” and 0.25mm on “E” per side.
2. Dimension “b” does not include dambar
protrusion.

Marking:
Top side :2yww

2 = part number (US2882)

y = last digit of year
ww = calendar week

Hall plate location

1.417
0.891

Notes:

0.275 1. All dimensions are in millimeters

SIDE VIEW

Package line
TOP VIEW

This table in mm
A A1 A2 D E E1 L b c e e1 
min – 0.025 0.85 2.80 2.60 1.50 0.30 0.30 0.10 0.95 1.90 0°
max 1.00 0.10 0.90 3.00 3.00 1.70 0.50 0.45 0.20 BSC BSC 8°

REVISION 006 – 13 JUNE 2019 Page 10 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

17.2. UA Package (TO-92 flat)

Notes:
1. Mold flashes and protrusion are not included.
2. Gate burrs shall not exceed 0.127mm on the top side.

2.0

1.4

0.425

This table in mm
A D E F J L L1 S b1 b2 c e e1
min 2.80 3.90 1.40 0.00 2.51 14.0 1.55 0.63 0.35 0.43 0.35 2.51 1.24
max 3.20 4.30 1.60 0.20 2.72 15.0 1.75 0.84 0.44 0.52 0.44 2.57 1.30
   
min 5° 5° 45° 3°
max MAX REF REF REF

REVISION 006 – 13 JUNE 2019 Page 11 of 12

390100288201
US2882
Bipolar Hall Switch – Very High Sensitivity

18. Contact
For the latest version of this document, go to our website at www.melexis.com.

For additional information, please contact our Direct Sales team and get help for your specific needs:

Europe, Africa Telephone: +32 13 67 04 95

Email : [email protected]

Americas Telephone: +1 603 223 2362

Email : [email protected]

Asia Email : [email protected]

19. Disclaimer
The information furnished by Melexis herein (“Information”) is believed to be correct and accurate. Melexis disclaims (i) any and all liability in connection with or arising out of the
furnishing, performance or use of the technical data or use of the product(s) as described herein (“Product”) (ii) any and al l liability, including without limitation, special,
consequential or incidental damages, and (iii) any and all warranties, express, statutory, implied, or by description, includ ing warranties of fitness for particular purpose, non-
infringement and merchantability. No obligation or liability shall arise or flow out of Melexis’ rendering of technical or other services.
The Information is provided "as is” and Melexis reserves the right to change the Information at any time and without notice. Therefore, before placing orders and/or prior to
designing the Product into a system, users or any third party should obtain the latest version of the relevant information to verify that the information being relied upon is current.
Users or any third party must further determine the suitability of the Product for its application, including the level of reliability required and determine whether it is fit for a
particular purpose.
The Information is proprietary and/or confidential information of Melexis and the use thereof or anything described by the In formation does not grant, explicitly or implicitly, to
any party any patent rights, licenses, or any other intellectual property rights.
This document as well as the Product(s) may be subject to export control regulations. Please be aware that export might require a prior authorization from competent authorities.
The Product(s) are intended for use in normal commercial applications. Unless otherwise agreed upon in writing, the Product(s ) are not designed, authorized or warranted to be
suitable in applications requiring extended temperature range and/or unusual environmental requirements. High reliability applications, such as medical life-support or life-
sustaining equipment are specifically not recommended by Melexis.
The Product(s) may not be used for the following applications subject to export control regulations: the development, production, processing, operation, maintenance , storage,
recognition or proliferation of 1) chemical, biological or nuclear weapons, or for the development, production, maintena nce or storage of missiles for such weapons: 2) civil
firearms, including spare parts or ammunition for such arms; 3) defense related products, or other material for military use or for law enforcement; 4) any applications that, alone
or in combination with other goods, substances or organisms could cause serious harm to persons or goods and that can be used as a means of violen ce in an armed conflict or any
similar violent situation.
The Products sold by Melexis are subject to the terms and conditions as specified in the Terms of Sale, which can be found at https://www.melexis.com/en/legal/terms-and-
conditions.

This document supersedes and replaces all prior information regarding the Product(s) and/or previous versions of this document.

Melexis NV © - No part of this document may be reproduced without the prior written consent of Melexis. (2016)

ISO/TS 16949 and ISO14001 Certified

REVISION 006 – 13 JUNE 2019 Page 12 of 12

390100288201