Vickers®

Service Data
Directional Controls

Wet Armature Directional Control Valves

DG4S4-01*B/C-(U)-*-60

Revised 04-93 I-3879-S

 VOLTAGE DC COIL DIN COIL- Spool Assembly Notes
COIL S/A COIL KIT Assembly type “1” spool with relieved
60 HZ 50 HZ VOLT CODE KIT
land towards “A” port.
868982 892995 120 110 B 893007 879141 Assembly type “3” spool with narrow
868983 892996 240 220 D 893008 879143 land towards “A” port.
Assembly type “11” spool with relieved
868984 892997 460 440 M 893009 879231 land towards “B” port.
868985 892998 127 EG 893010 879232 Assembly type “31” spool with narrow
879211 240 ED 879142 land towards “B” port.
879212 110 A 879144 Type “68C” is the same as type “6”
879213 220 C 879227 except solenoid is assembled on
24 879228 opposite end (do not reverse solenoid
879214 NN on “68B” models) and a different
879215 893003 100 100 T 893015 879229 diagram plate is used. Type “68C/B”
879216 893004 380 380 DZ 893016 879230 models are used as pilots for spring
02–101843 24 24 N 02–101845 centered two stage valves with “4” or
02–101976 200 200 OV 02–127060 “8” type spools only.
868987 892999 12 G 893011 879146 Type “78C” is the same as type “7”
868988 893000 24 H 893012 879147 except solenoid is assembled on
868989 893001 48 J 893013 879148 opposite end (do not reverse solenoid
on “78B” models) and a different
868990 110 P 879226 diagram plate is used. Type “78C/B”
868991 100 R 879225 models are used as pilots for pressure
868992 893002 250 X 893014 879224 centered two stage valves with “4” or
879233 125 DP 879149 “8” type spools only.
02-119664 48 48 K 02-127061 Type 8C spools. Solenoid designations
02-119665 48 KK 02-127062 are reversed.
02-127063 Type 8B spools. Left hand assembly
02-119666 24 NV with coil “A” shown. For right hand as-
02-300515 220 DN 02-300519 sembly, all parts of valve except spool
02-300516 115 EK 02-300520 and body are reversed.
02-300517 110 100 BX 02-300521
SPOOL TYPE PART SPOOL KIT
02-300518 320 200 DX 02-300522
0 463385 892977
1 463386 892978
11 463386 892988
DIN Coil Mating 2 463387 892979
Receptacle 3 463388 892980
31 463388 892981
6 880886 892983
68 880886 892984
7 463390 892985
78 463390 892986
DIN Coil (See Table) 8 463391 892987
33 463392 892982
DIN Coil (See Table)
879209 Plug (2 Req’d)
zSpool (See table)
g868952 Washer (2) ‘C’
(2) ‘B’ Models
868951 Stop (2) ‘C’
(2) ‘B’ Models

691417 Spring (2) C’ (1) ‘B’ Models

236451 Spring for spools 1B/11B only
02-153961 Push Pin
(2) ‘C’ (1) ‘B’ Models
262338 ‘‘O’’ Ring
(2) ‘C’ (1) ‘B’ Models
U Core Tube S/A
AC – 02-153967
H Coil (See Table) (2) ‘C’ (1) ‘B’ Models DC – 879169
(Coil ‘A’ shown for Type 8B, 68B &
78B spools
YHz 187000 O" Ring (2) ‘C’ (1) ‘B’ Models
879172 Knob (2) ‘C’ (1) ‘B’ Models
 Note
SPOOL TYPE DIAGRAM PLATE
For satisfactory service life of these
11 & 31 290339 components in industrial applications,
8 290340 use full flow filtration to provide fluid
0 290341 which meets ISO cleanliness code
1 290342 18/15 or cleaner.
2 290343
3 290344
6 290345 Note
7 290346 Refer to other end of valve for common
68 577480 part numbers.
78 577482
33 577484

[z 174638 Screw (4 Req’d)

z Nameplate (Not
available for sale)

286122 Gasket
& Wire S/A

36212 Screw DG4S4–01*C

Body (Not available for sale)

263493 “O” Ring
O 407533 Plug DG4S4–01*B

U 691468 Plug
Yz 262338 “O” Ring
879209 Plug

O 407533 Plug
263493 “O” Ring

YJz 868968 Gasket Diagram Plate (See table)

416834 Rivet (4 Req’d)

YJz 262334 “O” Ring (5 Req’d)

DC Coils with Surge Suppression Device Encapsulated

Coil S/A DC Voltage DIN Coil S/A Coil Code
02-154795 12 02-154798 G
02-154767 24 02-154796 H
Refer to model code for ordering with surge suppression.
Included in F3 Seal Kit 892976
Spool/Spring Arrangement z Included in Spool Kit
Note J Included in Coil Kit
B models only g Rounded face on 868952 washer
Right hand assembly shown (except type must mate with spool
’8’). For left hand assembly (–LH models), U Torque 24–29 N.m (18–22 lbf. ft.)
all parts of valve except spool and body O Torque 12.1–12.4 N.m (107–110 lbf. in.)
are reversed. Use left hand diagram plate. [ Torque 0.8–1.01 N.m (7–9 lbf. in.)
Model Code

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 Special Seals 7 Electrical Accessories 11 Wet Armature Solenoid

(non-serviceable core tubes)
Blank - Standard seals L - Solenoid indicator lights
F3 - Special seals W - Wiring housing Blank - Flying lead coils
LW - Wiring housing with indicator lights U- DIN 43650 coils w/o electrical
WT - Wiring housing with terminal strip plug
2 Directional Control Valve

3 8 Interface 12 Coil Type

Manifold or Subplate Mounted
01 - ISO-4401-AC-50-4-A NFPA D05 7- Coil with surge suppression
4 Solenoid Operated (1/8 in. nominal size) (DC models only 12 & 24V DC)

5 Sliding Spool 13
9 Spool Types Coil Identification Letters

6
0, 1, 2, 3, 6, 7, 8, 11, 31 & 33
Flow Direction 14 Design
4 - Four way
10 Spool/Spring Arrangement 15 Left-Hand Assembly
B - Spring centered solenoid ‘A’ removed (omit for right-hand assembly)
C - Spring centered, three position

Light Kits 298785 Screw

298782 Gasket
Solenoid Indicator Light Kit Indicator light
(Includes all parts identified) Identification plate
Voltage Range Kit
100 thru 127 941615
192 thru 233 941617