Veo 16:64 Inspection Report

Software: 3.17.11, Unit serial #: I005091

Component Config File Name File Vers. Operator Procedure Ref Inspection Date
21 HORNO TEQ.utcfg 10 R GONGORA UT 01 2024-07-04 12:06

S1 - Sectorial PE Gain G1 ^ %FSH G1 ^ ⇓⊻ G2 ^ %FSH G2 ^ ⇓⊻ G1-G2 ^ ⇘

25.3 dB -- -- -- -- --

Legend : Inspection Info Encoder Info

Abbrev. Description Target Enc. Rate Mid Encoding Setup Time Based
BPL Path Length Voltage Phased Ar. 100 V
Part Info
D Depth Probe 1 [Freq, Mod... 5.00 MHz, Sonatest-T1-PE-5.0M32E...
Material Steel
SD Surface Dist. Wedge 1 [Velo, Mo... 2.330 mm/µs, Sonatest-T1-35W0D-...
Velocity [LW/SW] 5.890 mm/µs, 3.329 mm/µs
A Amplitude
Part Geometry Plate
L Length
Thickness 21.00 mm
DLT Delta
Weld Single V
*[Smoothing, Sub-Sampling]

Scan S1 - Sectorial PE Value

Signal Processing* High, Auto: 1:4
Digital Filter Auto: 5.0 MHz
Gain , Ref 25.3 dB, 25.3 dB
Focal [Type, Dist] Constant Depth, 15.00 mm
Start/Stop Path 0.00 mm, 110.00 mm
Start/Stop Angle 40.00°, 75.00°
Max PRF 1365 Hz
Acq. Freq. 100 MHz

21 HORNO TEQ_0001 J2 135-180.pdf Page 1

 Veo 16:64 Inspection Report
Software: 3.17.11, Unit serial #: I005091
Inspection
Probe Qty 1 Alarms Off Operator R GONGORA
Scan Qty 1 Encoded Axis Ref. Wedge Reference Qualification II
Voltage Phased Ar. 100 V Job/Customer TEQUENDAMA Procedure Ref UT 01
Target Enc. Rate Mid Site SUESCA Couplant ULTRAGEL

Part
Material Steel Velocity LW 5.890 mm/µs Weld Root Gap 2.00 mm
Condition PLATE Velocity SW 3.329 mm/µs Weld Top Bevel Width 24.00 mm
Temperature 20.0°C Cal. Block Serial # J10160 Weld Face Left 1.95 mm
Component N/A Cal. Block Type PACS Weld Top Left Width 12.00 mm
Serial # N/A Cal. Block Sensibility Ref. 1 64 Weld Top Left Angle 30.00°
Location Ref SUESCA Rejection Criteria ASME V Weld Top Left Height 19.05 mm
Part Geometry Plate Velocity SW 3.329 mm/µs
Thickness 21.00 mm Weld Single V

Probe P1 - Phased-Array 1D
Probe Type Phased-Array 1D Elmt Size Dim 1 0.76 mm Elmt Pitch Dim 1 0.80 mm
Manufacturer Sonatest Pulse Type Square-Wave Elmt Offset Dim 1 3.20 mm
Model # Sonatest-T1-PE-5.0M32E0.8P Pulse Width 100.00 ns Elmt Offset Dim 2 8.60 mm
Serial # 0810-5274-16A First Elmt Pin # 1 Element Layout Bottom Left Row
Frequency 5.00 MHz Nb Elmt Dim 1 32 Elmt Size Dim 2 12.00 mm

Wedge P1 - Phased-Array 1D
Type Angular Back Height 6.00 mm Roof Angle 0.00°
Manufacturer Sonatest Cut Angle 35.00° Probe Back Dist 2.50 mm
Model # Sonatest-T1-35W0D-REXO Front Height 28.80 mm Probe Side Dist 1.00 mm
Serial # N/A Width 31.00 mm Probe Inset 0.00 mm
Contact Surface Planar Length 54.00 mm Wedge Velocity LW 2.330 mm/µs

Scan S1 - Sectorial PE
Type Sectorial PE Max PRF 1365 Hz Last Elmt RX 15
Gain , Ref 25.3 dB, 25.3 dB Signal Rectification Full Beam Qty. 71
Resolution 0.50° Digital Filter Auto: 5.0 MHz Sample Qty. 1656
Start Angle 40.00° Sub-Sampling Auto: 1:4 Path Res. 15.1 spl/mm
Stop Angle 75.00° Rejection Disabled Acq. Freq. 100 MHz
Start Path 0.00 mm Smoothing High Velocity Cal Status Accepted
Range Path 110.00 mm Contouring No Wedge Delay Cal Status Accepted
Stop Path 110.00 mm Probe TX/RX P1 - Phased-Array 1D Sensitivity Cal Status Accepted
Zero 1.28 µs Probe RX P1 - Phased-Array 1D Amp Tolerance 10.00%
Wave Mode SW 3.329 mm/µs First Elmt TX 1 TCG Cal Status Accepted
Travel Mode Half Path Last Elmt TX 15 Amp Tolerance 5.0%
Focal Mode Constant Depth nbElementsUsedTx 15
Focal Dist 15.00 mm First Elmt RX 1

Geometry
W1 Index Off. -30.00 mm W1 Rotation 90.0°
W1 Scan Off. 0.00 mm

21 HORNO TEQ_0001 J2 135-180.pdf Page 2 (End)