Digital Lab

POWER SOLUTIONS
30W-300W

Regulated DC Power Supplies

19” Rack Adaptable

l - 3U High

Digital
l Output Metering
3 Digit DPM

Constant
l Voltage/Constant
Current Operation

High Stability
l and Close
Regulation ±0.01%

Proven
l Reliability and
Endurance

3U High
l

133mm
Remote
l Sensing Facility for
310mm 225mm
5A & Above Rating Models

133mm

430mm 250mm

The New Series offers a range of Linear All the models operate in either constant
DC Regulated Power Supplies for use in voltage or constant current mode and
Laboratories & Industries. Output are fully protected against continuous
voltage and current values are displayed output short circuit and overload.
on a 3 digit DPM.
DIGITAL LAB SUPPLIES are being sold
These table top units are designed for all over the world since 1974 and
19” Rack Mounting. several thousand units are currently in
service.
There are ten models to choose from,
with output power ranging from 30 watts
to 300 watts. Output voltages of 0-16V,
OPTIONS AT EXTRA COST
0-32V, 0-64V and 0-128V DC are
available for single output supplies. 1) 19” Rack mounting only for PS with
There are four Dual output models with 430mm width.
two independent isolated outputs. 2) Over voltage protection.
These outputs could be connected in
3) Input 115V AC ±10%.
series or parallel to double the voltage
or current.

www.aplab.com
 Digital Lab
POWER SOLUTIONS
30W-300W

Regulated DC Power Supply

DIGITAL LAB SELECTION GUIDE

SPECIFICATIONS
Output Voltage & Current : See
SINGLE OUTPUT 30-300W
Selection Guide.
OUTPUT DC OUTPUT DIMENSIONS MODEL
Metering : 3 Digit DPM.
VOLTAGE CURRENT W x H x D (mm) Meter Accuracy : ±3 counts.
16V 0-16V 0-2A 210 x 133 x 250 L1602 Constant Voltage Mode :
0-16V 0-6A 430 x 133 x 250 L1606 Regulation :
Line : ±0.01% ±2mV for ±10%
0-16V 0-10A 430 x 133 x 250 L1610 change in line output.
Load : ±0.01% ±2mV for load
32V 0-32V 0-2A 210 x 133 x 250 L3202
change from zero to full load.
0-32V 0-5A 430 x 133 x 250 L3205 Ripple & Noise : 1mV rms max.
0-32V 0-10A 430 x 133 x 250 L3210 20Hz - 20MHz.
Constant Current Mode :
64V 0-64V 0-3A 430 x 133 x 250 L6403
Regulation :
0-64V 0-5A 430 x 133 x 250 L6405 Line : ±0.1% ±250µA for ±10% line
change.
128V 0-128V 0-2.5A 430 x 133 x 250 L1282 Load : ±0.1% ±250µA for change in
output voltage from 0 Volts to
maximum output voltage.
Ripple & Noise : 0.04% rms.
Mode Indication : LED indication for
constant voltage / constant current
operating mode.
DIGITAL LAB SELECTION GUIDE Output Polarity : Floating w.r.t. ground.

DUAL OUTPUT Overload Protection : Automatic

overload and short circuit protection.
OUTPUT VOLTAGE CURRENT DIMENSIONS MODEL
W x H x D (mm) Transient Response : 100µsecs to
within 10mV of set output voltage for load
0-32V 0-2A 430 x 133 x 250 LD3202 change from 10% to 90%.
2 0-16V 0-6A 430 x 177 x 250 LD1606 Stability : Total drift within 8 hours, after
warm-up.
0-64V 0-2A 430 x 177 x 250 LD6402
< ±0.2% plus 5mV in constant voltage
Load Regulation to be measured at sense terminals wherever provided. mode.
< ±0.5% plus 5mA in constant current
mode with constant line, load and
ambient temperature conditions.
Operating Temperature : 0-50OC.
Line Voltage : 230V AC ±10% 50Hz,
single phase.
For 10% variation in input voltage with constant rated load. All dimensions are behind the panel and excluding legs.
Load change from no load to full load. Change in output voltage from zero volt (Short circuit) to max. output voltage. NOTE : REGULATION TO BE
WE PURSUE A POLICY OF CONTINUOUS DEVELOPMENT AND PRODUCT IMPROVEMENT. THUS THE SPECIFICATIONS IN MEASURED AT SENSE TERMINALS.
THIS DOCUMENTS AND THE LOCATION OF CONTROLS ON THE FRONT PANEL MAY BE CHANGE D WITHOUT NOTICE

CUSTOM CAPABILITY :
SPECIAL VOLTAGE AND CURRENT
RATINGS AVAILABLE ON REQUEST.

POWER CONTROLS & CONVERSION DIVISION

Aplab Limited Plot No. 12, TTC Industrial Area, Thane Belapur Road, Digha, Navi Mumbai - 400 708. India. Email : [email protected]