General SHERLOG CRX is a modular, multi-functional measurement and analysis system for comprehensively

description monitoring and assessing equipment in electricity supply systems. It combines the monitoring functions of
high-resolution digital fault recorders, power quality analysers, phasor measurement units, continuous data
recorders and event recorders in one device.
Individual devices can be networked via an Interlink interface to monitor extensive installations.

Multi-processor Digital signal processor (DSP) for processing signals and processes in real time
system Communication processor
for mass data storage, simultaneous data communication using different interfaces and
protocols, web server functionality and stand-alone operation

User controls and 8 status LEDs for alarm, trigger and status display
displays 3.5" colour graphical display with touch screen and 4 function keys

Number of 8…32 analog inputs

measurement inputs 0…128 binary inputs

Data memory 32 GB flash RAM for reliable data storage

Quality system Developed and manufactured to DIN ISO 9001

Calibration Software-controlled calibration

Calibration data is saved on the individual measurement modules
No calibration required after module replacement or upgrade (plug & play)
Recommended calibration cycle: check every 5 years

Operating software SHERLOG operating software for Windows 7, Windows 8.1 (32 and 64 bit),
Windows 10 (32 and 64 bit), Windows Server 2012 R2

Function Recording functions Digital fault recorder, 2 sampling rates from 500 Hz…30 kHz
overview RMS fault recorder, sampling rate from 1 Hz...120 Hz
Continuous data recording
Event data recording
Power quality analyser, class A (optional)
Phasor measurement unit/PMU (optional)

Standards for IEC 61000-4-30 class A

measurement and IEC 61000-4-7 harmonics and interharmonics
analysis
IEC 61000-4-15 flicker
EN 50160, IEEE 519, IEEE 1159
IEEE C37.118

Technical specifications subject to change without prior notice | ©03/2018 KoCoS Messtechnik AG
www.kocos.com Doc. 7618000 Rev. 1.50
Analog inputs General information Resolution 16 Bit, S/R:92 dB typical

Sampling frequency 200 kHz per channel

Accuracy 0.05% of range

Protection Galvanic isolation

Channel-channel: 2.5 kV; channel-device: 2.5 kV

Input module Number of 8 inputs with selectable measuring ranges for:

Type 1 measurement inputs
Voltage measurement
Current measurement with external sensors (e.g. shunts)
Measurement of low-level signals

Measuring ranges Each measurement input has 4 selectable measuring ranges:

Measuring range 1:
300 VAC / ±424 VDC; impedance 6.6 MΩ
Measuring range 2:
700 mVAC / ±1000 mVDC; impedance 14.7 kΩ
Measuring range 3:
200 mVAC / ±282 mVDC; impedance 14.7 kΩ
Measuring range 4:
±20 mA / 4…20 mA; impedance 10 Ω

Overload 1000 VAC sustained in the 300 V measuring range

Frequency range DC…10 kHz

Input module Number of 4 separate high-current inputs for connection to protection or

Type 2 measurement inputs instrument transformers

Measuring ranges Each measurement input has 3 selectable measuring ranges:

Measuring range 1: 10 AAC; impedance 0.002 Ω

Measuring range 2: 40 AAC; impedance 0.002 Ω
Measuring range 3: 200 AAC; impedance 0.002 Ω
Overload 40 AAC sustained
200 AAC for 5 seconds
500 AAC for 1 second

Frequency range 10 Hz…10 kHz

Binary inputs Input module Number of 16 inputs per module

measurement inputs Galvanically isolated in 4 groups of 4 inputs
Max. 8 input modules (128 inputs)

Activation range 24…300 VDC (wide-range inputs)

Resolution 0.1 ms

Protection Transient protection

Polarity protection
Galvanic isolation up to 2.5 kV

Binary outputs Electronic relays Number 2, freely configurable for status and alarm signals

Switching capacity Max. 60 VAC/DC, 200 mA

Mechanical relays Number 8, freely configurable for status and alarm signals

Contact type Potential-free relay contact

Configurable as NC or NO contact

Switching capacity Max. 220 VAC, 8 AAC, max. 60 W, max. 500 ms

Max. continuous current: 2 AAC
Required fuse: 2.5 A slow blow

Technical specifications subject to change without prior notice | ©03/2018 KoCoS Messtechnik AG
www.kocos.com Doc. 7618000 Rev. 1.50
Time Standard equipment Internal real-time clock Accuracy 2.5 ppm without external time synchronisation
synchronisation
NTP/SNTP Synchronisation over Ethernet network

Interlink interface Master-slave time synchronisation between several SHERLOG

CRX devices

Synchronisation GPS receiver Internal GPS receiver with SMA antenna connection
module (optional) Accuracy of internal seconds pulse: <60 ns

Optical GPS input For connection to external GPS systems over optical fibre
(2 x ST II)
Time telegram: NMEA-0183-RMC, 4800 baud, non-inverted
Pulse input: seconds or minutes pulses, non-inverted

DCF 77 input DCF 77 pulse telegram input for connection to external clock
systems or to the KoCoS DCF 77 antenna module

Pulse input for seconds PPS/PPM impulse input

or minutes pulses 5…12 V / 24…80 V , min. pulse width 5 ms

IRIG-B signal input Coaxial connection for B001, B002 and B003 telegrams

Interfaces Standard equipment Data communication 2 x RS232, 1 x RS485

2 x USB-A, 1 x USB-B
1 x 10/100 Mbit Ethernet (RJ 45)

Interlink interface Electric 2-wire interface for networking a number of SHERLOG

CRX devices
Enables cross-triggering and master-slave time synchronisation
over distances of up to 500 m

Interface module Data communication 1 x 10/100 Mbit optical Ethernet (ST II)
(optional)
1 x 10/100 Mbit Ethernet (RJ 45)

Interlink interface Optical Interlink interface for networking a number of

SHERLOG CRX devices
Enables cross-triggering and master-slave time synchronisation
by means of a fibre optic loop
Maximum distance between 2 devices is 2 km

Protocols Standard: TCP/IP, Modbus TCP, IEC 60870-5-103, GSM, GPRS

Optional: IEC 61850, IEEE C37.118 (PMU)

Power supply Operating voltage Type 1: 90…365 VDC and 85…265 VAC; 47…63 Hz
Type 2: 9…18 VDC
Type 3: 18…36 VDC
Type 4: 36…72 VDC

Working range: +6% / -10% of the nominal range

Power consumption Max. 30 VA with maximum configuration (32 analog and 128 binary inputs)

Redundancy Power supply unit and power supply redundancy provided by accommodation of up to
two independent power supply modules of the same type or of different types

Technical specifications subject to change without prior notice | ©03/2018 KoCoS Messtechnik AG
www.kocos.com Doc. 7618000 Rev. 1.50
Complete system Mechanical Weight 2.9 kg
properties
Housing 19" housing for rack mounting, 84 HP/3 U

Protection class IP 52 (front panel)

Dimensions 483 mm x 132.5 mm x 263 mm

Environment Storage temperature -20…70 °C

Maximum -5…55 °C, minimum switch-on temperature 0 °C

temperature limit

Relative humidity 5…95%, non-condensing

Other RoHS-compliant

Generic standards Safety EN 61010-1

EMC emissions EN 61000-6-4 (replaces EN 50081-2)

Susceptibility EN 61000-6-2 (replaces EN 50082-2)

Measurement category 300 V CAT III, 150 V CAT VI

EMC standards IEC 60255-1 Measuring relays and protection equipment - Part 1

IEC 60255-5 IEEE C37.90 Dielectric test, 2.5 kV, 50 Hz

Insulation test, 500 V, 50 Hz
Impulse voltage test, 5 kV, 0.5 Joule

EN 55011 CISPR 11 Radiated radio disturbances

CISPR 16 30…230 MHz at 10 m, 40 dB (µV/m)
CISPR 22 230…1000 MHz at 10 m, 47 dB (µV/m)

EN 55011 CISPR 11 Conducted radio disturbances

CISPR 16 0.15…0.5 MHz, 79 dB (µV) Q, 66 dB (µV) A
CISPR 22 0.5…5 MHz, 73 dB (µV) Q, 60 dB (µV) A
5…30 MHz, 73 dB (µV) Q, 60 dB (µV) A
IEC 61000-4-2 IEC 60255-22-2 Electro-static discharge test, class 4
8 kV contact, 15 kV air
IEC 61000-4-3 IEC 60255-22-3 Radiated susceptibility
10 V/m, 80…3000 MHz, AM
10 V/m, 900 MHz, PM
IEC 61000-4-4 IEC 60255-22-4 Electrical fast transient burst
IEEE C37.90.1 4 kV, 2.5 kHz, 5 kHz, 100 kHz

IEC 61000-4-5 IEC 60255-22-5 Surge test, class 4

4 kV common mode
2 kV differential mode
IEC 61000-4-6 IEC 60255-22-6 Conducted susceptibility
10 V, 150 kHz…80 MHz
IEC 61000-4-8 IEC 60255-6 Power frequency magnetic field
30 A/m, 50 Hz, x, y, z axis
IEC 61000-4-11 IEC 60255-11 Supply voltage dips and interruptions, class 3

IEC 61000-4-18 IEC 60255-22-1 Damped oscillatory waves

2.5 kV, 1 MHz common mode
1.0 kV, 1 MHz differential mode
Vibration IEC 60068-2-6 IEC 60255-21-1 Vibration test
Standards 5.2 g, 5…55 Hz, x, y, z axis
IEC 60068-2-27 IEC 60255-21-2 Vibration test
5 g / 11 ms, x, y, z axis
Climatic IEC 60068-2-1 Cold storage test
standards Storage at -45 °C for 96 hours
Operation at -5 °C for 16 hours
IEC 60068-2-2 Cyclic temperature test, dry heat
16 hours, 55 °C, operating condition
96 hours, 70 °C, power off condition

Technical specifications subject to change without prior notice | ©03/2018 KoCoS Messtechnik AG
www.kocos.com Doc. 7618000 Rev. 1.50