FWM 396
FWM 396
FWM 396
/55/BK/78
TABLE OF CONTENTS
2008
Location of PCBS
du FRONT/MCU BOARD
VERSION VARIATIONS :
Type /Versions: FWD396
Electronic specification
AMPLIFIER TUNER
1 kHz FM wave range ...................................... 87.5 – 108 MHz
(low channel - both channels driven) AM wave range (9 kHz) ......................... 531 – 1602 kHz
................................................... 50 W per channel (6 Ω)
10 kHz SPEAKERS
(high channel - both channels driven) System 1-way; 1 port bass reflex
................................................... 50 W per channel (6 Ω) Impedance ................................................................ 6 Ω
Total output power............................................. 200 W Woofer .................................................................. 1 x 5"
Signal-to-noise ratio .......................... ≥ 60 dBA (IEC) Tweeter ............................................................... 1 x 1.5"
Frequency response .......................... 50 – 16000 Hz Dimensions (w x h x d) . 207 x 309 x 214 (mm)
Input sensitivity Weight ................................................... 2.8 kg each
AUX/Line In ............................................................. 2 V
Microphone ....................................................... 1.5 mV GENERAL
Output Material/finish ................................... Polystyrene/Metal
Speakers ............................................................. ≥ 6 Ω AC Power ............................ 110 – 127 / 220 – 240 V;
(1) (6 Ω 1 kHz, 10% THD) ................................................... 50/60 Hz Switchable
Power Consumption
CD/MP3-CD PLAYER Active ............................................................... 110 W
Number of programmable tracks ............................... 40 Dimensions (w x h x d)265 .. x 310 x 403 (mm)
Frequency response ...................... 50 – 16000 Hz -3dB Weight (without speakers) ................................. NJ
Signal-to-noise ratio ....................................... ıG%$
Channel separation .......................... ıG% N+]
7otal harmonic distortion ................................. < 0.6%
MPEG 1 Layer 3 (MP3-CD) ..................... MPEG AUDIO
MP3-CD bit rate ......................................... 32-256 kbps
(128 kbps advised) Specifications and external appearance are
Sampling frequencies ....................... 32, 44.1, 48 kHz subject to change without notice.
MEASUREMENT SETUP
Tuner FM
Bandpass
DUT 250Hz-15kHz LF Voltmeter
e.g. 7122 707 48001 e.g. PM2534
RF Generator
e.g. PM5326
Ri=50:
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Tuner AM (MW,LW)
Bandpass
250Hz-15kHz LF Voltmeter
DUT e.g. 7122 707 48001 e.g. PM2534
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Ri=50:
Frame aerial
e.g. 7122 707 89001
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
CD Recorder
Use Audio Signal Disc SBC429 4822 397 30184 Use Universal Test Cassette CrO2 SBC419 4822 397 30069
(replaces test disc 3) or Universal Test Cassette Fe SBC420 4822 397 30071
DUT
DUT LF Generator L
L e.g. PM5110
R
R
S/N and distortion mete
S/N and distortion meter e.g. Sound Technology ST170
e.g. Sound Technology ST1700B
LEVEL METER
LEVEL METER e.g. Sennheiser UPM550
e.g. Sennheiser UPM550 with FF-filter
with FF-filter
SERVICE AIDS
GB WARNING ESD
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
GB
Safety regulations require that the set be restored to its original CLASS 1
condition and that parts which are identical with those specified,
be used LASER PRODUCT
Safety components are marked by the symbol ! .
Lead free
INSTRUCTIONS ON CD PLAYABILITY
Customer complaint
"CD related problem"
playability N
ok ?
Y 3
For flap loaders (= access to CD drive possible)
"fast" lens cleaning cleaning method 4 is recommended
check playability
playability N
ok ?
Play a CD
for at least 10 minutes
check playability
playability N
ok ?
return set
INSTRUCTIONS ON CD PLAYABILITY
1 4
PLAYABILITY CHECK LIQUID LENS CLEANING
Before touching the lens it is advised to clean the
surface of the lens by blowing clean air over it.
For sets which are compatible with CD-RW discs
This to avoid that little particles make scratches on
use CD-RW Printed Audio Disc ....................7104 099 96611
the lens.
TR 3 (Fingerprint)
TR 8 (600μ Black dot) maximum at 01:00
Because the material of the lens is synthetic and coated
• playback of these two tracks without audible disturbance with a special anti-reflectivity layer, cleaning must be done
playing time for: Fingerprint t10seconds with a non-aggressive cleaning fluid. It is advised to use
Black dot from 00:50 to 01:10 “Cleaning Solvent
• jump forward/backward (search) within a reasonable time
2
CUSTOMER INFORMATION
Display shows
Ver: x.x
Disassembly Diagram
Block Diagram
AMP BOARD
MAIN BOARD
FRONT/MCU BOARD
Wiring Diagram
IC
IC
EXPLODE VIEW
MECHNICAL&MISCELLANEOUS PARTS
101 996510014307 LED HOLDER
102 996510014308 LCD BRACKET
103 996510014309 LCD LIGHT GUIDE
201 994000001276 PANEL LEFT
202 994000001277 PANEL RIGHT