Form # Z540

Date 2-02lA
Model 5092 & 5092L
1" Super Duty Pistol
Grip ImpactTools
IMPORTANT
C? 0
Read these instructions carefully before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe accessible place.

1 SAFETY MESSAGES 1A WARNING 1 Operator Instructions

1 Use - Safety Glasses

Use - Safety Gloves
Personal Safety Equipment
YES 1 0@ Always Read Instructions Before
"sing Power Tools
Always Wear Safety Goggles
1 Includes:
Safety Rules
ores seenUse
Use - Safety Boots Work Stations
@ Wear Hearing Protection Putting Into Service
Use - Breathing Masks Operating
Avoid Prolonged Exposure
Use - Ear Protectors YES A To Vibration Disrnantlina and Assernblv.
Safety rules when using a 509215092L Impact Tool
- Use only impact sockets and extensions, universaljoints, - It is expected that users will adopt safe working practices
etc., rated as being suitable for use with impact tools. and observe all local, regional or country legal
- Prolonged exposure to vibration may cause injury. requirements when installing,using or maintainingthe tool.
- Read all instructions before usingthis tool. All operators must - Take care that the exhaust air does not point towards any
be fully trained in its use and aware of these safety rules. other person or material or substance that could be
- Do not exceed the maximum working air pressure. contaminated by oil droplets. When first lubricating a tool
- Use personal protectionequipment as recommended. or if the tool exhaust has a high oil content, do not allow
- Some dust created by power sanding, sawing, grinding, the exhaust air to come near very hot surfaces or flames.
drilling, and other construction activities contains - Never lay the tool down until the working attachment has
chemicals known to cause cancer, birth defects and other stopped moving.
reproductive harm. - When the tool is not in use, shut off the air supply and
- Use compressed air only at the recommendedconditions. press throttle triggerllever to drain the supply line. If the
- If the tool aooears to malfunction, remove from use tool is not to be used for a oeriod of time. first lubricate.
immediatelyand arran e for service and repair. If it is not disconnect from air supply &d store in a dry average room
practical to remove tooTfrom service, then shut off the air temperature environment.
supply to the tool and write or have written a warning - If the tool is passed from one user to a new or inexperi-
note and attach it to the tool. enced user, make sure these instructions are available to
- If tool is to be used with a balancer or other suspension be passed with the tool.
device, ensure that the tool is firmly attached to the - Do not remove any manufacturer fitted safety devices
suspension/support device. where fitted, i.e., wheel guards, safety trigger, speed
- When operating the tool, always keep the body and governors, etc.
particularly the hands away from the working attachment - Wherever possible, secure workpiece with clamps, avise,
fixed to the tool. etc. to make it rigid so it does not move during the work
- The tool is not electrically insulated. Never use the tool if operation. Keep good balance at all times. Do not stretch
there is any chance of coming into contact with live or overreach.
electricity. - Try to match the tool to the work operation. Do not use a
- Always when usin the tool, adopt a firm footing and/or tool that is too light or heavy for the work operation. If in
position and grip &e tool sufficiently only to overcome doubt, seek advice.
any reaction forces that may result from the tool doing - In general terms, this tool is not suitable for underwater
work. Do not overgrip. use or use in explosive environments-seek advice from
- Use only correct spare parts for maintenanceand repair. manufacturer.
Do not improvise or make temporary repairs. Major - Try to make sure that the work area is clear to enable the
servicing and repairs should only be carried out by work task to be performed safely. If practical and
persons trained to do so. possible, try to clear unnecessary obstructions before
- Do not lock, tape, wire, etc. the 'OnIOff' valve in 'On' starting work.
position.The throttle triggerllever, etc.must always be free - Always use air hose and couplings with minimum work-
to return to the 'Off' ~ositionwhen released. ing pressure ratings at least 1 112 times the maximum
- Alwa s shut off the 'air supply to the tool and press the working pressure rating of the tool.
'on/&' valve to exhaust the air from
the feed hose before fitting, removina 7
or adjusting the working attachment
fitted to the tool.
- Before usingthe tool, make sure that a
shut off device has been fitted to the
supply line and the position is known
and easily accessible so that the air
supply to the tool can be shut off in an Easy To Reach And Air Tool
emergency.
- Check hoseand fittings regularlyfor wear.
- Take care against entanglement of the
moving parts of the tool with clothing, hair,
ties, cleaning rags, rings,jewelry, watches,
bracelets, etc.This could cause the body
or parts of the body to be drawn towards
and in contact with the moving parts of the
tool and could be very dangerous. Recommended Air Supply System Figure 1
Page No 1