Product information

Klüber Summit PS 100, 150, 200, 300, 400

Semi-synthetic air compressor oils for oil change intervals up to 5,000 operating
hours

Benefits for your application

– Low maintenance and operating costs due to oil change intervals up to 5,000 operating hours in
oil-injected screw-type compressors
– Easier compressor oil changeover due to neutral behaviour of oils towards seals
– Good soil dissolving capacity, clean oil circuit due to the ester content in the oil, reduction of cleaning costs
– Low formation of oxidation residues in the oil circuit, reduced operating costs due to extended oil filter and
separator life

Description Application notes

Klüber Summit PS oils are air compressor oils based on When selecting the oil viscosity for air compressors please
hydrogenated mineral oil, synthetic ester oil and additives. observe the manufacturers’ instructions.
Klüber Summit PS oils are miscible with mineral oils and When switching a used compressor to Klüber Summit PS oils,
synthetic hydrocarbons, but not with oils based on polyglycol. drain the old oil from the whole circuit while still warm. We also
recommend changing all oil filters and separators. Then refill
the compressor with Klüber Summit PS oil.
Application
When switching from mineral oil to a Klüber Summit PS oil
Klüber Summit PS oils have been especially designed for the please consider that the compressor may contain oxidation
lubrication of screw-type and reciprocating piston compressors. residues in the form of blackened or contaminated oil. As such
They are used for oil change intervals up to 5,000 operating residues can affect the service life of the fresh Klüber Summit
hours in oil-injected screw-type compressors. PS oil, the compressor should be cleaned using the Klüber
Klüber Summit PS oils can be used for compressors that were Summit Varnasolv conditioner.
previously run with conventional mineral oils. These oils are For further information, please consult the Klüber Summit
neutral towards most elastomer seals used in air compressors, Varnasolv product information leaflet or contact Klüber
therefore leakage is not to be expected. Lubrication.
Klüber Summit PS oils are used for compressors which do not After switching to a Klüber Summit PS oil we recommend
achieve the desired maintenance intervals when using mineral determining the oil change interval through an oil analysis or the
oils and where the use of fully synthetic oils would be Klüber Summit TAN Kit.
uneconomical due to ingress of contamination or a low number
of operating hours per year.
Klüber Summit PS 100 can also be used for the lubrication of Material safety data sheets
turbocompressors, whereas Klüber Summit PS 300 and 400 Material safety data sheets can be requested via our website
have been especially developed for reciprocating piston www.klueber.com. You may also obtain them through your
compressors. contact person at Klüber Lubrication.
Klüber Summit PS oils offer good oxidation stability due to the
synthetic base oil content, thus minimising oxidation residues in
the compressors and extending oil change intervals and the
service life of oil filters and separators. Special inhibitors
contained in the oil keep the inside of compressors clean and
ensure a high efficiency.

Pack sizes Klüber Klüber Klüber Klüber Klüber

Summit PS Summit PS Summit PS Summit PS Summit PS
100 150 200 300 400
Canister 19 l + + + + +
Drum 208 l + + + + +

Klüber Summit PS 100, 150, 200, 300, 400,Prod. 050052, 050053, 050054, 050055,
050056,en
Edition 09.04.2018 [replaces edition 05.01.2018]
Klüber Summit PS 100, 150, 200, 300, 400
Semi-synthetic air compressor oils for oil change intervals up to 5,000 operating
hours

Product data Klüber Klüber Klüber Klüber Klüber

Summit PS Summit PS Summit PS Summit PS Summit PS
100 150 200 300 400
Article number 050052 050053 050054 050055 050056
Appearance clear clear clear clear clear
Colour space colourless colourless colourless colourless colourless
Density, DIN 51757, 20 °C approx. 0.87 approx. 0.87 approx. 0.87 approx. 0.88 approx. 0.88
g/cm³ g/cm³ g/cm³ g/cm³ g/cm³
Kinematic viscosity, DIN 51562 pt. 01/ASTM approx. 32 approx. 46 approx. 68 approx. 100 approx. 150
D-445/ASTM D 7042, 40 °C mm²/s mm²/s mm²/s mm²/s mm²/s
Kinematic viscosity, DIN 51562 pt. 01/ASTM approx. 5.5 approx. 6.8 approx. 8.4 approx. 10.6 approx. 14.3
D-445/ASTM D 7042, 100 °C mm²/s mm²/s mm²/s mm²/s mm²/s
Viscosity index, DIN ISO 2909 >= 90 >= 90 >= 90 >= 90 >= 90
Pour point, DIN ISO 3016 <= -30 °C <= -30 °C <= -27 °C <= -30 °C <= -27 °C
Copper corrosion, DIN EN ISO 2160, 3 h/100 1 - 100 1 - 100 1 - 100 1 - 100 1 - 100
°C corrosion corrosion corrosion corrosion corrosion
degree degree degree degree degree
Foam test, ASTM-D 892, ISO 6247, sequence <= 50/0 ml <= 50/0 ml <= 50/0 ml <= 50/0 ml <= 50/0 ml
I/24 °C
Foam test, ASTM-D 892, ISO 6247, sequence <= 50/0 ml <= 50/0 ml <= 50/0 ml <= 50/0 ml <= 50/0 ml
II/ 93.5 °C
Foam test, ASTM D 892, ISO 6247, sequence <= 50/0 ml <= 50/0 ml <= 50/0 ml <= 50/0 ml <= 50/0 ml
III/24°C
Demulsifying capacity, DIN 51599, ASTM D 40/37/3 ml 40/37/3 ml 40/37/3 ml
1401, at 54 °C
Demulsifying capacity, DIN ISO 6614, ASTM D 40/37/3 ml 40/37/3 ml
1401 at 82 °C
Flash point, DIN EN ISO 2592, Cleveland, >= 200 °C >= 210 °C >= 230 °C >= 240 °C >= 240 °C
open-cup apparatus
Minimum shelf life from the date of 36 months 36 months 36 months 36 months
manufacture - in a dry, frost-free place and in
the unopened original container, approx.

Klüber Summit PS 100, 150, 200, 300, 400,Prod. 050052, 050053, 050054, 050055, 050056,en
Edition 09.04.2018 [replaces edition 05.01.2018]
Klüber Summit PS 100, 150, 200, 300, 400,Prod. 050052, 050053, 050054, 050055, 050056,en
Edition 09.04.2018 [replaces edition 05.01.2018]
 Product information

Klüber Summit PS 100, 150, 200, 300, 400

Semi-synthetic air compressor oils for oil change intervals up to 5,000 operating
hours

Klüber Lubrication München SE & Co. KG /

Geisenhausenerstraße 7 / 81379 München / Germany /
Klüber Lubrication – your global specialist phone +49 89 7876-0 / fax +49 89 7876-333.

Innovative tribological solutions are our passion. Through The data in this document is based on our general experience and knowledge at
the time of publication and is intended to give information of possible applications
personal contact and consultation, we help our customers to be to a reader with technical experience. It constitutes neither an assurance of
successful worldwide, in all industries and markets. With our product properties nor does it release the user from the obligation of performing
ambitious technical concepts and experienced, competent staff preliminary field tests with the product selected for a specific application. All data
are guide values which depend on the lubricant's composition, the intended use
we have been fulfilling increasingly demanding requirements by and the application method. The technical values of lubricants change depending
manufacturing efficient high-performance lubricants for more on the mechanical, dynamical, chemical and thermal loads, time and pressure.
than 80 years. These changes may affect the function of a component. We recommend
contacting us to discuss your specific application. If possible we will be pleased to
provide a sample for testing on request. Klüber products are continually improved.
Therefore, Klüber Lubrication reserves the right to change all the technical data in
this document at any time without notice.
Publisher and Copyright: Klüber Lubrication München SE & Co. KG. Reprints,
total or in part, are permitted only prior consultation with Klüber Lubrication
München SE & Co. KG and if source is indicated and voucher copy is forwarded.