BH-30S Light Wand

01

11
NEEWER

19

27

35

43

51

Polish 59
Sweden 67
75

BH-30S Light Wand With Barndoors

Instruction Manual

About this product Product Illustration

Thanks for purchasing the NEEWER BH-30S RGB Light Wand.
The BH-30S is a handheld RGB light wand used for photography lighting. With
built-in rechargeable batteries and an upgraded charging circuit, the light boasts
an extended operating time of up to 150 minutes. Easily switch between the CCT
mode, HSI mode and Scene mode to provide vibrant colored lights to achieve
Display
your desired lighting effects for photography and videography, both indoors and
out.

Illuminated LOGO
Infinity/2.4G Mode
NEEWER

EN EN Power
EN ENButton (long press) Touchpad Lock button
(short press)
Press on the adjustment
Package Contents dial: HSI mode Press right dial:
Color Temperature
Press left: Rotate the dial:
Brightness mode changes item values
Press down: Navigate through items
Scene mode (short press)

RGB Color Mixer

Handle Locking Knob
BH-30S RGB Light Wand ×1

Angle Adjustment Knob

 Integrated Handle

USB Charging Cable ×1 Handle ×1

Stand Securing Knob

BH30S Barndoors
×1

USB Charging Port 1/4" Screw Hole

NEEWER

Carrying Bag ×1
※ Long press the " " button for 5 seconds to reset the Infinity connection.

01 02 03

How to Use How to Use

Turning the light on/off Adjusting saturation

Press upper dial "HSI" to enter HSI

Long press the " " Power Button
mode. Next, short press the center
until the display lights up and the
dial " " until the S number flashes
light wand turns on.
on the display, then rotate the dial
to set saturation value.

EN EN

Adjusting brightness level Adjusting hue (via HSI mode)

In any mode, simply press on the Press upper dial "HSI" to enter HSI
left dial "INT" until the display shows mode. Next, short press center dial
the " " symbol flashing, then rotate " " until the H number is flashing
the dial to adjust the brightness level. on the display, then rotate the dial
to set hue value.

Adjusting hue (via RGB Color Mixer)

Changing color temperature
In any mode, short press the " "
Press right dial "CCT" to change to
button until the " " icon disappears
color temperature screen. Short
on the display. Then move the RGB
press the center dial " " until
Color Mixer with your finger to adjust
the symbol "00K" is flashing on
hue. Short press the " " button again
the display. Rotate the dial to change
until the diaply shows the " "
color temperature values.
symbol. This indicates that the RGB
Color Mixer is now locked.

Red and green compensation

Setting special scenes
value adjustment
Press lower dial "SCENE" to activate
Press right dial "CCT" to change into the light's SCENE mode. Short press
color temperature screen. Short center dial " " until light scene
press the center dial " " until the flashes on the display. Rotate the
symbol "GM" is flashing on the dial to switch between different
display. Rotate the dial to set scenes.
red/green color compensation
value.

05 06
FCC Statement IC Warning Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

CAUTION: The user is cautioned that changes or modifications not expressly

approved by the party responsible for compliance could void the user's authority
to operate the equipment.

EN E
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an
uncontrolled environment.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

09