TP0703B
TP0703B
TP / TP-B TYPE
●FEATURE
1. High current capacity
2. Large terminal surface for good PCB bonding
●Applications
1. DC-DC converter or LCD TV and others
●Shape and Dimension ●Schematics and Land Patterns(mm)
d2
E
●Specification Dimension in m/m
TYPE A B C E d2 F
TP03015B 3.7 Max 3.3 Max 1.5 Max 3.60 1.00 3.50
TP0302B 3.7 Max 3.3 Max 2.1±0.30 3.60 1.00 3.50
TP0403B 4.5±0.30 4.0±0.30 3.2±0.30 4.70 1.30 4.10
TP0502B 5.8±0.30 5.2±0.30 2.0±0.30 6.00 1.30 5.30
TP0504B 5.8±0.30 5.2±0.30 4.5±0.30 6.00 1.30 5.30
TP0703B 7.8±0.30 7.0±0.30 3.5±0.40 8.00 2.10 7.20
TP0705B 7.8±0.30 7.0±0.30 5.0±0.50 8.00 2.10 7.20
TP1004 10.0±0.30 9.0±0.30 4.0±0.50 10.20 2.10 9.20
TP1005 10.0±0.30 9.0±0.30 5.4±0.50 10.20 2.10 9.20
TP1006 10.0±0.30 9.0±0.30 7.5 Max 10.20 2.10 9.20
Note1. Measurement frequency of Inductance value : at 100KHz, 0.25V
Note2. Measurement ambient temperature of L, DCR and IDC : at 25℃
Note3. IDC : This indicates the value of current when the inductances is 10% lower than its initial
value at D.C. superimposition (Ta=20℃)
Note4. Inductance tolerance: M: ±20% ; K: ±10%
Note5. Ordering Code: TYPE NAME: TP0504
Main Inductance: 100 (10uH)
Tolerance : M (±20%)
Note6. Packaging: Taping
6R3 6.3
8R0 8.0
102 1000
2R0 2.0
3R0 3.0
3R3 3.3 0.088 / 2.40 0.045 / 3.20 0.036 / 2.89 0.023 / 4.00
3R9 3.9
4R7 4.7 0.130 / 2.10 0.054 / 2.50 0.048 / 2.60 0.025 / 3.50
6R3 6.3
6R8 6.8 0.166 / 1.70 0.070 / 2.00 0.060 / 2.02 0.042 / 3.20
8R0 8.0
101 100 1.697 / 0.20 0.700 / 0.52 0.481 / 0.51 0.430 / 0.72
151 150 2.912 / 0.17 1.100 / 0.40 0.755 / 0.40 0.640 / 0.58
221 220 4.706 / 0.15 1.570 / 0.35 1.200 / 0.31 0.960 / 0.49
821 820
102 1000
2R0 2.0
2R7 2.7
3R0 3.0
3R3 3.3
3R9 3.9
6R3 6.3
6R8 6.8
8R0 8.0
8R2 8.2
102 1000
GENERAL CHARACTERISTICS
1. Operating temperature range: -40 TO + 105℃(Includes tem perature when the coil is heated)
2. External appearance: On visual inspection, the coil has no external defects.
3. Terminal strength: After soldering. Between copper plate and terminals of coil. Push in two directions of X.Y
withstanding at below conditions.
Terminal should not peel off. (refer to figure at right) 10. 0N 10 sec.
4. Insulating resistance: Over 100MΩ at 100V D.C. between coil and core.
5. Dielectric strength: No dielectric breakdown at 100V D.C. for 1 minute between coil and core.
6. Temperature characteristics: Inductance coefficient (0~2,000)x10-6/℃(-25~+80℃).
7. Humidity characteristics(Moisture Resistance): Inductance deviation within ±5%, after 96 hours in 90~95%
relative humidity at 40 ±2℃and 1 hour drying under norm al condition.
8. Vibration resistance: Inductance deviation within ±5%, after vibration for 1 hour. In each of three orientations
at sweep vibration (10~55~10 Hz) with 1.5mm P-P amplitudes.
9. Shock resistance: Inductance deviation within ±5%, after being dropped once with 981m/s2 (100G) shock
attitude upon a rubber block method shock testing machine, in three different orientations.
10. Resistance to Soldering Heat: 260℃, 10 seconds(See attached recom m end reflow)
11. Storage environment: Storage condition: Temperature Range: 10℃ ~ 35℃ (G enerally: 21℃ ~ 31℃) ,
Humidity Range: 50% ~ 80% RH (Generally: 65% ~ 75%) ; Transportation condition: Temperature Range:
-35℃ ~ 85℃ , Hum idity Range: 50% ~ 95% RH
12. Use components within 12 months. If 12 months or more have elapsed, check solderability before use.
13. Reflow profile recommend:
L e a d -fre e h e a t e n d u ra n ce t e s t L e a d - f r e e t h e r e c o m m e n d e d r e f lo w c o n d it io n
T( ℃ ) T (℃ )
300 30 0
26 0 ℃
250 25 0 2 45 ℃ P eak
23 0℃ 2 3 0℃
200 20 0
40
10
150 15 0
60
1 7 0 ± 1 0 ℃ ,6 0 - 1 2 0 S
100 10 0
50 50
0 T(s 0 T (s)
0 60 1 20 18 0 24 0 300 0 60 12 0 18 0 24 0 300