0% found this document useful (0 votes)
48 views11 pages

10.control Panel

Uploaded by

Thoi Co
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
48 views11 pages

10.control Panel

Uploaded by

Thoi Co
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 11

Control panel

10 Control Panel

10-1 0i MC OPERATIONAL PANELS


10-1-1 8.4” LCD / MDI FULL-KEY

10-1-3 MITSUGISHI CONTROL PANEL

10-1
Control panel

10-2 MACHINE CONTROL PANEL


1.Below control panel is used on LMV850, LMV1000, MV820, ,MV1000, MV1100,MV1050,MV1350,
MV2200

10-3 OTHER CONTROL PANEL


MPG

10-2
Control panel

10-4 INSTRUCTION OF OPERATION PANEL

10-4-1 MODES DESCRIPTION

(AUTO MODE)press this key for executing automatic operation mode.

(EDIT MODE)this mode is used for modifying or increasing machining


programs. For detailed instructions, refer to program input instructions
given in the operation manual.
(DNC MODE)This mode is used for transferring data, machining
programs or for DNC transfer. For detailed instructions, refer to
program input instructions given in the operation manual.
(MDI MODE)This mode is used for specifying or editing the temporary
working commands. For detailed instructions, refer to the programming
instruction manual. A single block can be input and executed through
this MDI mode.

10-3
Control panel
(ZERO POSITION MODE)Press this key and any manual control key,
then the corresponding axis will return to its reference position. When
this mode is selected, press the axis moving direction key, then the
machine will return to its machine reference position with the speed of
25% of G00(first reference position). The axis travel speed will slow
down when approaching to the reference position. When the reference
position indication lamp lights on, it means the axis has returned to its
reference position.
(JOG MODE)Press this key for moving each axis by using manual
control key.

(HANDLE MODE)Press this key, then you may use MPG handle to
move each axis. The axis direction and magnification are shown on the
handle panel.

10-4-2 FUNCTIONS DESCRIPTION

Not available.

Turn on this switch for execution programs pre-play, however the F


command set in the program is ineffective. Feed rate will be determined
by the G01 regulator, located on the main panel.
When a single block is marked with (/) at the head end, it will be
ineffective during automatic operation. When this key is pressed on,
any single block marked with (/) will not be executed. When this key
is pressed off, any command with or without (/) marking will be
executed.
When this key is in On condition, during automatic operation, any
single block containing M01 command will cause automatic operation
stop. When this occurs, press the program start key to continue

10-4
Control panel
execution, When this key is in OFF condition, M01 is ineffective.
When this key is pressed, during executing programs , any of M, S,T,
command cannot be executed.

When this switch is turned on, then any axis can not be moved.

When this key is pressed, in automatic operation mode, the machine


executes only a single block then stop. When this key is in ON
condition and in automatic operation mode, only a single block can be
executed. If you need to executer the next single block, press the
program start key.
When the mode selection switch is set at reference position mode, and
this key is pressed, the Z-axis will return to its reference position at
first, then X,Y-axis simultaneously return to their reference positions.
Press this key for turning on the work light, however it is effective only
when the switch on the work light also been turned on. Press this key
again for light off.

10-4-3 MAHAZINE FUNCTIONS DESCRIPTION

When operation mode is set at jog or MPG handle mode, and the
magazine manual indication lamp lights on, press this key once, then
the magazine will clockwisely rotate a tool position. Keep pressing on
this key for continuous rotation of magazine. Release the key, then
the magazine rotation will stop.
When manual rotation of magazine is required, you need to set at jog
or MPG handle mode, and press this key. Then the magazine CW or
CCW manual will be effective.
When operation mode is set at jog or MPG handle mode, and the
magazine manual indication lamp lights on, press this key once, then
the magazine will counter-clcokwisely rotate a tool position. Keep
pressing on this key for continuous rotation of the magazine. Release
the key, then the magazine rotation will stop.

10-5
Control panel
This screen displays the actual tool numbers on the spindle and the
tool pocket. On an armless type magazine, the tool numbers displayed
for the spindle and the pocket are the same. However, on an arm type
magazine, the displayed tool numbers between both will be different.

10-4-4 CHIP CONVEYOR FUNCTIONS DESCRIPTION

Under any mode condition, when this key is pressed, the chip
conveyor will start running. Chip conveyor can also be started by
using the M code. For details refer to M code functions list.
Press this key for stopping the chip conveyor.

When this key is pressed, the chip conveyor starts running counter-
clockwisely. Release this key for stopping the chip conveyor. This
function is applied when chip jamming occurs.

10-4-5 SPINDLE CONTROL FUNCTIONS DESCRIPTION

Under jog or MPG handle mode, when this key is pressed, the spindle
starts running clockwisely.

Under any mode condition, when this key is pressed, the spindle stops.

Under jog or MPG handle mode, when this key is pressed, the spindle
starts running counter-clockwisely.

Press this key for increasing 10% of spindle speed. Maximum


increase of spindle speed is of up to 120%.

10-6
Control panel
Press this key for returning spindle speed to 100%.

Press this key for decreasing 10% of spindle speed. Minimum


decrease of spindle speed is 50%.

10-4-6 FEED FUNCTION DESCRIPTION

Under jog mode, press any key on this area, then the axis will move
according to the speed set on the regulator knob for G01. If the rapid
traverse key is pressed, the axis will move with the speed set on the
regulator knob for G00.

The regulator knob is used for adjusting the G01 value during jog or
automatic operation mode. The adjustment range for G01 is 0-1260
mm/mm. or 0% -150 %. Another adjustment range 0% -200% is
available depending on the type of controller.

10-4-7 RAPID TRAVERSE DESCRIPTION

Under jog mode, press any key on this area, then the axis will move
according to the speed set on the regulator knob for G01. If the
rapid traverse key is pressed, the axis will move with the speed set
on the regulator knob for G00.
This regulator knob is used for adjusting the G01 value during jog
or automatic operation mode. The adjustment range for G01 is 0 –
1260 mm/mm or 0% - 150%. Another adjustment range 0%-200%
is available depending on the type of controller.
When the operation mode is set at jog mode

10-7
Control panel
During rapid traverse, you may adjust speed by turning this
regulator knob. Speed adjustment range is F0%, F25%, F50%and
F100%.

10-4-8 EMERGERNCY STOP FUNCTION DESCTRPTION

1. This emergency stop switch should be use d when an emergency


condition occurs, such as abnormal machine motion that may
damage operator or machine.
2. When the emergency stop switch is pressed, all motor powers
are cut off, but the main power source is not cut off.
3. Releasing this switch by turning it clock wisely or pulling it
upward. (Releasing method may be varied with the type of
emergency stop switch)
4. When the emergency stop switch has been pressed, all
commands and machine conditions will have been cleaned. To
restart the machine, you need to use the normal starting
procedures to continues, and also reference points return should
be made.
This key is operated together with handle food or manual feed
control key. This key is used only when an over-travel occurs.

10-4-9 CUTTING FLUID FUNCTIONS


When this key is pressed, the cutting fluid pump can be controlled
manually.

Press this key is to stop program execution automatically.

Press this key for stopping automatic program execution.

10-8
Control panel

10-4-10 OTHER FUNCTIONS AND INDICATIONS DESCRIPTION


Flushing device starting (optional)

Press this key for opening splash guard door (optional)

When this key is pressed, the automatic lubricator shots oil. Release
this key, oil shot stops.

Press this key for starting automatic program execution.

Press this key for stopping automatic program execution.

1. This key is used to prevent programs from being edited,


cancelled or modified.
2. In general, the key is set at ON position to ensure that programs
are not modified or cancelled.
3. When editing, canceling or modifying program is required, set
the key at OFF position.
4. When the key has been set at OFF position, you still need to set
the mode selection switch at EDIT position before performing
edition, canceling or modifying programs. Otherwise, it will
become invalid.
An warning for air system malfunction. It indicates air system
malfunction or air pressure is insufficient.
An warning for coolant system. It indicates coolant system
malfunction or pump motor damage.
It indicates spindle overload or spindle malfunction.
Hydraulic system malfunction.
When he lamp lights on, it means ATC works normally and

10-9
Control panel
magazine is in ready position.
When the lamp lights on, it means lubrication oil level is too low.
When the lamp lights on, it indicates the reference position for the
4th axis.
When X,Y,Z-axis indication lamps light on, it means axes are
located at the machine reference positions. (Any indication lamp for
X,Y,Z-axis lights on, it means the corresponding axis is located at its
reference position.
When second reference position indication lamp lights on, this
means the Z-axis is located at the tool changing position.

10-6 OPERATION INSTRUCTIONS FOR MPG

10-10
Control panel

Magnification selection knob


X1 :0.001mm
X10 :0.01mm
X100:0.1mm
Axis direction selection knob
OFF:handle off
X :For moving X-axis
Y :For moving Y-axis
Z :For moving Z-axis
4 :For moving 4th axis
Turn the hand wheel clockwisely for increasing value. Turn it
counter-clockwisely for decreasing value.

10-11

You might also like