Upgrade to the industry’s most advanced Motor Program:

AMP™ Motorization features 2-way technology with superior value and

innovation paired with a smart, seemless user interface.

Specifications
• 0.6Nm DC motor for TDBU and Honeycomb Standard shades
• Easy front access to programming and charging port
AMP TDBU • Compatible with AMP™ inside rail battery pack
Programming Guide
• Approximately 500 up/down cycles per each full charge
• 3 motor speed settings: 34, 40 or 50rpm
• Specially designed for patented AMP TDBU honeycomb shades
 AMP™ Motorization Table of Contents

Declarations 3

Safety Instructions 4

AMP™ TDBU System Overview 5

AMP™ TDBU Remote Function 6

P1 Button Instructions 8

Initial Set-up 9

Adjust Limits 10

Favorite Position 11

Add or Remove Additional Remote 12

Adjust Motor Speed 13

Roller or Sheer Mode 14

Quick Index 15

Troubleshooting 15

Please scan QR code to watch videos for

product programming

2 AMP ™
TDBU | PROGRAMMING GUIDE
 Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est
conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

3 AMP ™
TDBU | PROGRAMMING GUIDE
 Safety Instructions

Attention
Never drop, knock, drill or submerge the motor and RF receiver. Read all

safety instructions before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

× × × × × ×

Important Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.

2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

4 AMP ™
TDBU | PROGRAMMING GUIDE
 AMP™ TDBU System Overview

1. Fields of Application

Cellular/Honeycomb Cellular/Honeycomb
TDBU Day/Night

2. System Overview

3. RF Controller Overview

SSwwiit
tcchh

Charging Port
Charging Port
Motor
Motor 11Connection
Connection Port
Port
P1 Button
P1 Button
Motor
Motor 22Connection
ConnectionPortPort

Switch Functions
1. When the Switch is at Location 1, it is Cellular/Honeycomb TDBU and Cellular/Honeycomb Day/Night Shades working mode.
2. When the Switch move to Location ON, it is Cellular/Honeycomb Standard and Cellular/Honeycomb Skylight working mode.
3. The Factory defaulty mode is setting at Location 1.

4. Charging Instructions

ExEtxetrenranlaBl
aBtatettreyryPaPcakck

P1 Button
P1 Button

CChhaargring
ginPogrt

AMPTDBU Port

This motor connects with an external Li-ion battery pack with integrated charge management. Max
power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours using a 5V charger.
During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargable Battery
Rechargable BatteryStatus Indicator
Status Indicator

Blinking red: Blinking green: Solid green:

Low battery alert Charging in process Battery has finished charging

5 AMP ™
TDBU | PROGRAMMING GUIDE
 AMP™ TDBU Remote Function

1. Remote Button Instructions

Left Side Controls Right Side Controls

Bottom Rail Middle Rail
LCD Display
Left Up Right Up
P2
Left Stop Right Stop
Left Down Right Down

Lower Higher
Channel Channel P2

Switch

a.
2. Replace/Install CR2450 Battery b. c.

Battery
a. Unscrew with the screwdriver then gently press down the cover.
(CR2450)

b. Install battery (CR2450) with positive (=) side facing up.

c. Gently assemble the cover back and replace screw with screwdriver.

3. Channel Options

Select A Channel a.
Action on b.
a. Press “<” button on the remote to select a lower channel. Remote Control
Lower Higher
Channel Channel
b. Press “>” button on the remote to select a higher Remote Response
channel.
1 15

Hide Unused Channels Action on a. b.

Remote Control + or
a. Press and Hold (about 3 sec) “<” and “>” buttons simul-
Lower Higher Lower Higher
taneously until remote control displays “C” (channel). Channel Channel Channel Channel
Remote Response
b. Press “<” or “>” button to select required quantity of
C 11
channel (between 1 to 15).

c. Press “Stop” button to confirm selection (the example Action on c.

shows a 5-channel selection). The LCD will display “O” (OK) Remote Control
once to confirm selection. Stop

Remote Response
5

6 AMP ™
TDBU | PROGRAMMING GUIDE
 AMP™ TDBU Remote Function

4. Advanced Setting - Disable Limit Setting

a. Remove the cover from the backside of remote, the lock a.

switch is in the right corner.
Switch
b. Move the switch to the “Lock” position to disable the
following commands, remote will show “L” (lock):

- Change Motor Direction

- Setting the Upper and Lower Limit b.
- Adjust Limit Unlock Lock
- Roller Mode or Sheer Mode L
c. Move the switch to “Unlock” position to assess all remote Switch
functions, remote will show “U” (unlock).

c.
Unlock Lock
*This advanced feature is intended to be used after all shade
programming is completed. User Mode will prevent accidental U
or unintended changing of limits.
Switch

7 AMP ™
TDBU | PROGRAMMING GUIDE
 P1 Button Instructions

1. P1 Button Location

P1 Button

AMP TDBU honeycomb shades

2. P1 Button Instruction

1 Test Motor
Happening as you press for 1 second

Press P1
1 Less than 1 sec.

2 Activate Pairing Mode

Happening as you press for 2 seconds

Press P1
2 Approx. 2 sec. Until Shade: Jog x1

3 Sleep Mode
Happening as you press for 6 seconds

Press P1
6 Approx. 6 sec. Until Shade: Jog x2

4 Reverse Motor 1 with Motor 2

Happening as you press for 10 seconds

Press P1
10 Approx. 10 sec. Until Shade: Jog x3

5 Reset To Factory Settings

Happening as you press for 14 seconds

Press P1
14 Approx. 14 sec. Until Shade: Jog x4

8 AMP ™
TDBU | PROGRAMMING GUIDE
 Initial Set-up

1. Pair / Unpair Remote Control * All setup needs to be done using LEFT SIDE of the remote.
a. Press “P1” button (about 2 sec) on the End Cap as
shown until motor jog x1. Action on a.
Endcap
b. In the next 10 secs, press and hold Left “Stop” P1

button on the remote control until motor jog x2.

Motor Response Jog x1

Action on b.
Remote Control Motor
Left Stop
* Repeat the same procedure to unpair remote control.
Response Jog x2

2. Change Motor Direction (if necessary)

Press Left “Up” or Left “Down” button to check if the shade
moves in the desired direction. Action on +
Remote Control Left Up Left Down

If you need to reverse the direction, press and hold (about 2 sec)
Motor Response
Left “Up” and Left “Down” buttons simultaneously until Jog x1
motor jog x1.

*The operation is only valid when there are no limits.

3. Setting the Upper and Lower Limits

Set Upper Limit
Action on a. Action on
Remote Control b.
Remote Control
a. Press Right “Up” button to raise the Middle Rail, then press Right Up Left Up
Right “Stop” button when it is in the desired upper limit.
Middle Rail Bottom Rail Response
b. Press Left “Up” button to raise the Bottom Rail, then press Response
Left “Stop” button when it is in the desired upper limit.

c. Press and hold (about 2 sec) Left “Up” and Left “Stop”
buttons simultaneously until motor jog x2. c.
Action on
Remote Control
Left Up + Left Stop

Motor Response Jog x2

Set Lower Limit

Action on a. Action on b.
Remote Control Remote Control
a. Press Left “Down” button to lower the Bottom Rail, then Left Down Right Down
press Left “Stop” button when it is in the desired lower limit.
Bottom Rail Middle Rail Response
b. Press Right “Down” button to lower the Middle Rail, then Response
press Right “Stop” button when it is in the desired lower limit.

c. Press and hold (about 2 sec) Left “Down” and Left “Stop”
buttons simultaneously until motor jog x2. c.
Action on
Remote Control
Left Down
+ Left Stop

Motor Response Jog x2

Factory Mode Complete

User Mode Begins

9 AMP ™
TDBU | PROGRAMMING GUIDE
 Adjust Limits

1. Adjust the Upper Limit Action on a.

Remote Control Left Up + Left Stop
a. Press and hold (about 5 sec) Left “Up” and Left “Stop”
buttons simultaneously until motor jog x1. Jog x1
Motor Response

b. Use Right “Up” button to raise the Middle Rail, then press
Right “Stop” button when it is in the new desired upper limit. Action on b. Action on c.
Remote Control Remote Control
c. Press Left “Up” button to raise the Bottom Rail, then press Right Up Left Up
Left “Stop” button when it is in the new desired upper limit.
Middle Rail Bottom Rail
Response Response
d. Press and hold (about 2 sec) Left “Up” and Left “Stop”
buttons simultaneously until motor jog x2.

d.
Action on
Remote Control Left Up + Left Stop

Jog x2
Motor Response

2. Adjust the Lower Limit

a. Press and hold (about 5 sec) Left “Down” and Left Action on a.
“Stop” buttons simultaneously until motor jog x1.
Remote Control
Left Down
+ Left Stop

Jog x1
b. Use Left “Down” button to lower the Bottom Rail, then Motor Response
press Left“Stop” button when it is in the new desired lower limit.
Action on b. Action on c.
c. Press Right “Down” button to lower the Middle Rail, then Remote Control Remote Control
press Right “Stop” button when it is in the new desired lower Left Down Right Down
limit.
Bottom Rail Middle Rail Response
d. Press and hold (about 2 sec) Left “Down” and Left Response
“Stop” buttons simultaneously until motor jog x2.

*If you exit the limit setting status before you finish the limit d.
Action on
settings, the motor will take the previous existing limits.
Remote Control Left Down
+ Left Stop

Jog x2
Motor Response

10 AMP ™
TDBU | PROGRAMMING GUIDE
 Favorite Position

1. Set Favorite Position Action on b.

a. P2

a. Use Left “Up” or Left “Down” button to move

Remote Control or
Left Up Left Down
the shade to desired Favorite position.
Motor Response
or Jog x1
b. Press Right “P2” button on the back of remote
c. d.
control until motor jog x1. Action on
Remote Control Left Stop Left Stop

c. Press and hold (about 2 sec) Left “Stop” button until Motor Response Jog x1 Jog x2
motor jog x1.

d. Once more, press and hold (about 2 sec) Left “Stop”

button until motor jog x2.

2. Send Shade to Favorite Position

Press and hold (about 2 sec) Left “Stop” button, motor will Action on
move to Favorite position. Remote Control
Left Stop

Shade Response or

3. Delete Favorite Position a. P2 b.

Action on
Remote Control Left Stop
a. Press Right “P2” button until motor jog x1.

Jog x1 Jog x1
b. Press and hold (about 2 sec) Left “Stop” button until Motor Response
motor jog x1.
Action on c.
c. Once more, press and hold (about 2 sec) Left “Stop” Remote Control
Left Stop
button until motor jog x1. Motor Response Jog x1

11 AMP ™
TDBU | PROGRAMMING GUIDE
 Add or Remove Additional Remote

1. Using Current Remote Control

a. On the current remote control, press Right “P2” Action on a. Current Remote Control b. Current Remote Control
button until motor jog x1. Remote Control P2 P2

b. Once more, on the current remote control, press

Right “P2” button until motor jog x1.
Motor Response Jog x1 Jog x1
c. On the New remote control, press Right “P2”
button until motor jog x2.
Action on c. New Remote Control
Remote Control P2
*Repeat the same procedure to remove additional remote
control.
Motor Response
Jog x2

2. New Remote Control

Follow instructions under the section 1. Pair /
Unpair Remote Control

12 AMP ™
TDBU | PROGRAMMING GUIDE
 Adjust Motor Speed

1. Acceleration Speed

a. Press Right “P2” button until motor jog x1. Action on a. P2 b.

Remote Control
Left Up
b. Press Left “Up” button until motor jog x1.

c. Once more, press Left “Up” button until motor jog x2. Jog x1
Motor Response Jog x1

Action on c.
Remote Control
Left Up

Motor Response Jog x2

2. Deceleration Speed Action on a. P2 b.

Remote Control
Left Down
a. Press Right “P2” button until motor jog x1.

b. Press Left “Down” button until motor jog x1. Jog x1

Motor Response Jog x1
c. Once more, press Left “Down” button until motor
jog x2. Action on c.
Remote Control

Left Down
Motor Response
Jog x2

*If the motor has no response, it already has a

Maximum or Minimum speed.

13 AMP ™
TDBU | PROGRAMMING GUIDE
 Roller or Sheer Mode

1. Roller Shade Mode - continue movement

after a short press - Default Mode
a. Press and hold (about 5 sec) Left “Up” and Left “Down” Action on a.
buttons simultaneously until motor jog x1. Remote Control +
Left Up Left Down
b. Press and hold (about 2 sec) Left “Stop” button until
motor jog x2. Motor Response Jog x1

Action on b.
Remote Control
Left Stop

Motor Response Jog x2

2. Sheer Shade Mode - jog movement after a short

press (continue movement after a long press)
a. Press and hold (about 5 sec) Left “Up” and “Left Down”
buttons simultaneously until motor jog x1. Action on a.
b. Press and hold (about 2 sec) Left “Stop” button until
Remote Control
+
Left Up Left Down
motor jog x1.
Motor Response Jog x1

Action on b.
Remote Control
Left Stop
Jog x1
Motor Response

14 AMP ™
TDBU | PROGRAMMING GUIDE
 Quick Index

Settings Steps
1 Pairing P1 (hold down for 2s) > Left Stop (hold down for 2s)
2 Switch Rotating Direction Left Up + Left Down (hold down for 2s)
Upper Limit: Up (hold down for 2s) > Left Up + Left Stop (hold down for 2s)
3 Setting Upper & Lower Limits
Lower Limit: Down (hold down for 2s) > Left Down + Left Stop (hold down for 2s)
4 Add / Remove Favorite Position P2 > Left Stop > Left Stop
5 Roller Mode & Sheer Mode Switch Left Up + Left Down (hold down for 5s) > Stop
Upper Limit: Left Up + Left Stop (hold down for 5s) > Up or Down > Left Up + Left Stop (hold down for 2s)
6 Adjust Limits
Lower Limit: Left Down + Left Stop (hold down for 5s) > Up or Down > Left Down + Left Stop (hold down for 2s)
7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new)
Acceleration: P2 > Left Up > Left Up Deceleration:
8 Speed Regulation
P2 > Left Down > Left Down

Troubleshooting

Issues Possible Causes Solution

External battery pack is depleted Recharge with compatible AC adaptor and check connection and positioning of solar PV panel
Insufficient charging from Solar PV Panel Check connection and orientation of solar PV panel
Remote control battery is discharged Replace battery
Battery is inserted incorrectly into remote control Check battery polarity
The motor has no response Radio interference / shielding Ensure remote control and the antenna on the motor are positioned away from metal objects
Receiver distance is too far from Remote Control Move remote control to a closer position
Power failure Check power supply to motor is connected and active
Incorrect wiring Check that wiring is connected correctly (refer to motor installation instructions)
Always reserve an individual channel for programming functions
Cannot program a single motor
(multiple motors respond) Multiple motors are paired to the same channel. SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi-motor projects that provides
individual control for each motor for programming purposes
Place all other motors into sleep mode (ref to P1 button instructions)

Turnils Contact Information

Turnils North America

Turnils Canada
1750 Satellite Blvd, Suite 100
2908 Portland Drive
Buford, GA 30518
Oakville, Ontario L6H 5W8 1.800.268.4540
1.800.252.2512
[email protected]
[email protected]

15 AMP ™
TDBU | PROGRAMMING GUIDE