SFP 34060713-001

Overview
Optical Transceiver,SFP+,1310nm,9.8G,-8.2dBm~+0.5dBm,-10.3dBm,LC,SM,1.4km
Part Number 34060713-001
Model OSX1D4N01
Description Optical Transceiver,SFP+,1310nm,9.8G,-8.2dBm~+0.5dBm,-10.3dBm,LC,SM,1.4km
Discount Category Optical Transceiver
Product Line Networking
Product Series RTN 950
UOM PCS
Product Description
This Huawei® 34060713-001 compatible SFP+ transceiver provides 10GBase-LR throughput up to 2km over
single-mode fiber (SMF) using a wavelength of 1310nm via an LC connector. It is guaranteed to be 100%
compatible with the equivalent Huawei® transceiver. This easy to install, hot swappable transceiver has been
programmed, uniquely serialized and data-traffic and application tested to ensure that it will initialize and
perform identically. Digital optical monitoring (DOM) support is also present to allow access to real-time
operating parameters. This transceiver is Trade Agreements Act (TAA) compliant. We stand behind the quality
of our products and proudly offer a limited lifetime warranty.
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Notes
Maximum Supply Voltage Vcc -0.5 4 V 1

Storage Temperature TS -40 85 °C 2
Operating Case Temperature Tc 0 70 °C 3
Data Rate DR 9.83 10.3125 11.3 Gbps 4
Bit Error Rate BER 10-12
Notes:
1. For electrical power interface
2. Ambient Temperature
3. Case Temperature
4. IEEE 802.3ae
Link Distances
Data Rate Fiber Type Distance Range (km)
9.83 Gb/s 9/125um SMF 2
Electrical Characteristics (VCC=3.14V to 3.46V, TC=-0oC to 70oC)

Power Supply Voltage Vcc 3.14 3.30 3.46 V

Power Supply Current Icc 230 300 mA
Transmitter
Differential data input swing VIN,pp 180 700 mV

Input differential impedance RIN 100 Ω
Transmit Disable Voltage VD 2 Vcc V
Transmit Enable Voltage VEN VEE VEE+0.8 V
Receiver
Differential data output swing VOUT, pp 300 850 mV

Data output rise/fall time (20%-80%) Tr /Tf 28 ps
LOS Asset VLOSA 2 Host_Vcc V
LOS De-Assert VLOSD Vcc Vcc+0.5 V
Optical Characteristics
Transmitter
Output Optical Power Ptx -8.2 0.5 dBm 1

Optical Center Wavelength λc 1260 1310 1355 nm
Optical Modulation Amplitude OMA -5.2 dBm 2
Extinction Ratio ER 3.5 dB
Side Mode Suppression Ratio SMSR 30 dB
Relative Intensity Noise RIN -128 dB/Hz
Transmitter Dispersion Penalty TDP 3.2 dB
Launch Power of OFF Transmitter Poff -30 dBm 1
Receiver
Optical Center Wavelength λc 1260 1355 nm

Average Receive Power Prx -14.4 0.5 dBm
Receiver Sensitivity @10.3Gb/s S -14.4 dBm 3
Receiver Reflectance RL -12 dB
LOS Assert LOSA -30 dBm
LOS De-Assert LOSD -15 dBm
LOS Hysteresis LOSH 0.5 dB
Notes:
1. Average.
2. According to IEEE 802.3ae requirement.
3. Average. Test the resulting value using the minimum ER value within the defined range: BER<10-12, PRBS
231-1.
Pin Descriptions
Pin Symbol Name/Descriptions Ref.
1 VeeT Transmitter Ground (Common with Receiver Ground). 1

2 Tx_Fault Transmitter Fault. 2
3 Tx_Disable Transmitter Disable. Laser output disabled on “high” or “open.” 3
4 SDA 2-Wire Serial Interface Data Line. 4
5 SCL 2-Wire Serial Interface Clock Line. 4
6 MOD_ABS Module Absent. Grounded within the module. 4
7 RS0 No connection required.
8 LOS Loss of Signal indication. Logic 0 indicates normal operation 5
9 RS1 No connection required. 1
10 VeeR Receiver Ground (Common with Transmitter Ground). 1
12 RD– Receiver Inverted Data Out. AC Coupled.
13 RD+ Receiver Non-Inverted Data Out. AC Coupled.
15 VccR Receiver Power Supply
16 VccT Transmitter Power Supply
18 TD+ Transmitter Non-Inverted Data In. AC Coupled.
19 TD– Transmitter Inverted Data In. AC Coupled.
Notes:
1. Circuit ground is isolated from the chassis ground.
2. Tx_Fault is the open collector output and should be pulled up with 4.7kΩ-10kΩ on the host board to a
voltage between 2V and Vcc+0.3V.
3. Disabled: TDIS>2V or open, enabled: TDIS<0.8V.
4. Should be pulled up with 4.7kΩ-10kΩ on the host board to a voltage between 2V and Vcc+0.3V.
5. LOS is an open collector output and should be pulled up with 4.7kΩ-10kΩ on the host board to a voltage
between 2V and Vcc+0.3V. The logic "0" indicates normal operation, and the logic "1" indicates that the
receiver signal is lost.
Pin-out of connector Block on Host board
Block Diagram
Mechanical Specifications
Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-
Sourcing Agreement (MSA).
ALL DIMENSIONS ARE ±0.2mm UNLESS OTHERWISE SPECIFIED

UNIT: mm
EEPROM Information
EEPROM memory map specific data field description is as below:

SFP 34060713-001

Uploaded by

Copyright:

Available Formats

SFP 34060713-001

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SFP 34060713-001

Uploaded by

Copyright:

Available Formats

Overview

Part Number 34060713-001

Description Optical Transceiver,SFP+,1310nm,9.8G,-8.2dBm~+0.5dBm,-10.3dBm,LC,SM,1.4km

Discount Category Optical Transceiver

Product Line Networking

Product Series RTN 950

Maximum Supply Voltage Vcc -0.5 4 V 1

9.83 Gb/s 9/125um SMF 2

Electrical Characteristics (VCC=3.14V to 3.46V, TC=-0oC to 70oC)

Power Supply Voltage Vcc 3.14 3.30 3.46 V

Differential data input swing VIN,pp 180 700 mV

Differential data output swing VOUT, pp 300 850 mV

Output Optical Power Ptx -8.2 0.5 dBm 1

Optical Center Wavelength λc 1260 1355 nm

1 VeeT Transmitter Ground (Common with Receiver Ground). 1

ALL DIMENSIONS ARE ±0.2mm UNLESS OTHERWISE SPECIFIED

You might also like