Access Control Integration Host User’s Manual

V1.1.5
 Table of Contents

1 Overview ................................................................................................................................ 4
2 Device Structure and Installation......................................................................................... 5
3 Structure ................................................................................................................................ 8
System Structure .......................................................................................................................................... 8
3.2 Wiring ........................................................................................................................................................ 8
4 4 Function Setting ............................................................................................................... 12
4.1 Login....................................................................................................................................................... 12
4.2 User Management ............................................................................................................................. 12
4.2.2 4.2.1 Add User ............................................................................................................................... 13
4.2.3 4.2.2 Delete User .......................................................................................................................... 14
4.3 Unlock Mode ....................................................................................................................................... 15
4.4 Period Setup ........................................................................................................................................ 15
4.4.1 4.4.1 Card Swiping Period ........................................................................................................ 16
4.4.2 4.4.2 Holiday period.................................................................................................................... 16
4.4.3 4.4.3 Mode Period ....................................................................................................................... 17
4.5 System Settings .................................................................................................................................. 17
4.5.1 4.5.1 IP Setup................................................................................................................................. 17
4.5.2 4.5.2 Communication Setup .................................................................................................... 17
4.5.3 4.5.3 Date Setup ........................................................................................................................... 18
4.5.4 4.5.4 Unlock Time ........................................................................................................................ 18
4.5.5 4.5.5 Alarm Setup ........................................................................................................................ 18
4.5.6 4.5.6 Password Change ............................................................................................................. 19
4.5.7 4.5.7 Main Card Management................................................................................................. 19
4.5.8 4.5.8 Default .................................................................................................................................. 20
4.6 Reboot System.................................................................................................................................... 20
4.7 Local Info............................................................................................................................................... 21

1
Important Safeguards and Warnings
Note:
 Please change user default password after being armed.
 Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
 Do not expose the device to lampblack, steam or dust. Otherwise it may cause fire or
electric shock.
 The device must be installed on solid and flat surface in order to guarantee safety
under load and earthquake. Otherwise, it may cause device to fall off or turnover.
 Do not drop or splash liquids onto the device, and do not place container with full
liquid on the device to prevent liquid spilling from entering the device.
 Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
 Use the device only within rated input and output range.
 Do not disassemble the device without professional instruction.
 Please transport, use and store the product under appropriate temperature and
humidity.

Warning
 Please use battery properly to avoid fire, explosion and other dangers.
 Please replace used battery with battery of the same type.
 Do not use power line other than the one specified. Please use it properly within rated
range. Otherwise, it may cause fire or electric shock.
 Please use power supply matching SELV requirements, and IEC60950-1 Limited Power
Source. Power supply shall follow requirements on device label.
 For I-type structure product, connect it to power supply plug with GND protection.
 If you use power plug or appliance coupler as disconnecting device, please maintain
the disconnecting device available to be operated all the time.

Privacy Protection Notice

As the device user or data controller, you might collect personal data of others' such as
face, fingerprints, car plate number, Email address, phone number, GPS and so on. You
need to be in compliance with the local privacy protection laws and regulations to
protect the legitimate rights and interests of other people by implementing measures
include but not limited to: providing clear and visible identification to inform data
subject the existence of surveillance area and providing related contact.

2
About the Manual

 The Manual is for reference only. If there is inconsistency between the Manual and
the actual product, the actual product shall prevail.
 We are not liable for any loss caused by the operations that do not comply with
the Manual.
 The Manual would be updated according to the latest laws and regulations of
related regions. For detailed information, see the paper User's Manual, CD-ROM,
QR code or our official website. If there is inconsistency between paper User's
Manual and the electronic version, the electronic version shall prevail.
 All the designs and software are subject to change without prior written notice.
The product updates might cause some differences between the actual product
and the Manual. Please contact the customer service for the latest program and
supplementary documentation.
 There still might be deviation in technical data, functions and operations
description, or errors in print. If there is any doubt or dispute, please refer to our
final explanation.
 Upgrade the reader software or try other mainstream reader software if the Guide
(in PDF format) cannot be opened.
 All trademarks, registered trademarks and the company names in the Manual are
the properties of their respective owners.
 Please visit our website, contact the supplier or customer service if there is any
problem occurred when using the device.
 If there is any uncertainty or controversy, please refer to our final explanation.

3
 1 Overview
The Access Control Integration Host integrates card reading, config and execution functions. Its
has a neat appearance for medium to high-end clients such as commercial building, corporation
and intelligent community.

It has:
 Touch keyboard + LCD display, TCP/IP protocol, support 30,000 valid cards and 150,000
records.
 Support unlock via card, password, card+password, card or password and by period.
 Door time out alarm, intrusion alarm, forced alarm, and vandal-proof alarm.
 Add guest card, forced card, blocklist/allowlist and patrol card, while support period of
validity or times.
 Support 128 groups of schedule, 128 groups of period and 128 groups of holiday period.

4
 2 Device Structure and Installation
Device appearance, dimension and installation are shown below. Unit is mm.

5
6
Installation step:
Step 1. Fix installation bracket on wall or inside 86 box.
Step 2. Connect device wire and plug each wiring port.
Step 3. Make the device top toward slot on installation bracket.
Step 4. Joint device and installation bracket.
Step 5. Use screw to secure them from bottom.

7
 3 Structure

System Structure

3.2 Wiring
Wiring of the device is shown below.

8
Wiring ports are shown below.

9
 Table 3-1
No. Port No. Note
1 RS485+
①485+

RS485-
②485-

Connect GND
③GND

Alarm output 2（5V relay switch） ，external

④OUT2
connect to voltage not over 12V
Alarm output 1（5V relay switch） ，external
⑤OUT1
connect to voltage not over 12V
Connect GND
⑥GND

Alarm input
⑦IN

Ring control
⑧BELL

2 TCP/IP，network port
3 RS485+，485 card reader
①485+

RS485-，485 card reader

②485-

LED_OUT，Weigand card reader

③LED

D0，Weigand card reader

④D0

D1，Weigand card reader

⑤D1

10
No. Port No. Note
Card reader protection alarm
⑥CASE

Connect GND
⑦R-

12V card reader power

⑧R+

4 Connect unlock button

①PUSH

Connect GND
②GND

Door sensor check

③SR

Door lock NO end

④NO

Door lock NC end

⑤NC

Door lock COM end

⑥COM

Connect GND
⑦GND

12V power input

⑧12V

11
 4 4 Function Setting

Login
Login interface step:
Step 1. Plug in power, device is going to boot up.
Step 2. Press # button, screen displays project password.
Step 3. Input project password, and press # button to enter main interface.
Default password is “88888888”.
You can select to enter user management, unlock mode, period setup, system setting,
system reboot and local info as main menu.
 Press 【2】 button as up.
 Press 【8】 button as down.
 Press 【#】 button to enter or confirm.
 Press 【*】 button to return or exit.

User Management
You can add or delete card, password.

Table 4-1
Card Type Note
General card General user card.
When you add card, system will ask if set card password, period
and term of validity.
VIP card VIP user card. It warns service personal when cardholder enters.
When you add card, system will ask if set card password, period
and term of validity.
Guest card When you add guest card, you need to set usage times. So when
it exceeds this limit, the card becomes invalid.
Patrol card Patrol card can only swipe card at patrol spot but cannot unlock.
When you add card, system will ask if set card password, period
and term of validity.
Blocklist When you swipe card on blocklist and enters, it warns service
personal.
When you add card, system will ask if set card password, period
and term of validity.
Forces card Forced card becomes valid after you set forced alarm. You can
swipe this card to unlock, but an alarm will be send to center.

12
Note:
All of these cards will be sent to center, management platform will process according to card
type.
Password user represents user who input password in setup to enter.

Note:
 Card user has not set password, and you shall set unlock mode to card, card or password in
order to enter.
 Card user set card password, and you shall set unlock mode to card, card + password, card
or password in order to enter.
 User, who set period, can only unlock door within designated period.
 Password user, shall set unlock mode to card or password, password in order to enter.

4.2.2 Add User

4.2.2.1 Add Single Card

For example, you want to add a new card.

Step 1. In main interface, press 【2】or【8】 key to select user management, press 【#】 key.
Step 2. Press 【2】or【8】 key to move up or down, select add user and press【#】key.
Step 3. Press【2】or【8】 key to move up or down, select add care and press【#】key.
Step 4. Press【2】or【8】 key, to move up or down, select single card and press【#】key.
Step 5. Press【2】or【8】 key to move up or down, select normal card and press【#】key.
Step 6. Use key to input card no. or place card at swiping area to scan. Newly added card no.
will be displayed on screen.
Step 7. Press【#】key. System asks if you want to bind card with password.
Step 8. Choose:
 Yes: Input 6-digit password.
 No: System asks to set period.
Step 9. Press【#】key, set time period and press 【#】key.
Step 10. Press【#】, set term of validity and press 【#】. When you finish setup, system asks if
you want to save.
Step 11. Press【#】to save.

4.2.2.2 Add Continuous cards

For example, you want to add continuous cards.

13
Step 1. In add card interface, press 【2】or【8】 key to select add continuous cards, press
【#】 key.
Step 2. Press【2】or【8】 key to move up or down, select normal card and press【#】key.
Step 3. Input quantity of cards, press【#】key.
Step 4. Input card number of first card or swipe the first card, and press 【#】key. System asks
to bind password.
The following steps are similar to Ch 4.2.1.1.step 8 to 11.

4.2.2.3 Add Password User

To add password user:

Step 1. In add user interface, press 【2】or【8】 key to move up or down, select add password,
and press【#】key. System displays no. and password.
Step 2. Input password, and press 【#】key. Password must be 6 digits. System asks to save or
not.
Step 3. Press 【#】 to save.

4.2.3 Delete User

4.2.3.1 Delete Card User

You can delete a single card, continuous cards or all cards user.
To delete a single card:
Step 1. In user management interface, press 【2】or 【8】 key to select delete user, and press
【#】 key.
Step 2. Press 【2】or【8】 key to move up or down, select delete card and press【#】key.
Step 3. Press【2】or【8】 key, to move up or down, select single card and press【#】key.
Step 4. Input no. of card to delete, place the card at swiping area, and press【#】key.
System asks if to delete it or not.
Step 5. Press 【#】key to delete single card.

To delete continuous cards:

Step 1. In delete card interface, move up or down to select continuous card, and press 【#】
key.
Step 2. Input quantity to delete, and press 【#】.
Step 3. Input first card no. or place it on swiping area, and press【#】key. System asks if to delete
it or not.
Step 4. Press【#】key to confirm. System shows deleted result and quantity.
14
To delete all cards:
Step 1. In delete card interface, move up or down to select all cards, and press 【#】key. System
asks if to delete all or not.
Step 2. Press 【#】key to confirm. System says deleted successfully.

4.2.3.2 Delete Password User

You can delete a single password user or delete all password users.
To delete a single password user:
Step 1. In delete user interface, press 【2】or 【8】 key to select delete password, and press
【#】 key.
Step 2. Press 【2】or【8】 key to move up or down, select single password and press【#】
key.
Step 3. Input no. of password user to delete, and press【#】key.
System asks if to delete it or not.
Step 4. Press 【#】key to delete.

To delete all password users:

Step 1. In delete password interface, press 【2】or 【8】 key to select all password, and press
【#】 key. System asks if to delete it or not.
Step 2. Press 【#】key to delete.

Unlock Mode
Unlock mode includes card, password, card+password, card or password and by period.
To set:
Step 1. In main interface, press【2】or 【8】key to move up or down, select unlock mode, and
press【#】. Enter unlock mode setup page.
Step 2. Press【2】or 【8】 key to select mode to set, and press 【#】key. When it is selected,
there will be a √ next to the mode.

Period Setup
You can set unlock period, including card swiping period, holiday period and mode period.

15
4.4.1 Card Swiping Period
Card swiping period can be 0~127, a total of 128 periods. In each period, you need to set
schedule for each day of week. When a new card is added, and set card swiping period, then user
swipe card to unlock. Access control will judge if current time is within set period.
For example, set period 1, and the Monday to Sunday setup are shown below.

Table 4-2
Day Period
Monday 0800-2200 (valid period: 08:00 to 22:00)
Tuesday 0800-2200 (valid period: 08:00 to 22:00)
Wednesday 0800-2200 (valid period: 08:00 to 22:00)
Thursday 0800-2200 (valid period: 08:00 to 22:00)
Friday 0800-2200 (valid period: 08:00 to 22:00)
Saturday 0800-2200 (valid period: 08:00 to 22:00)
Sunday 0800-2200 (valid period: 08:00 to 22:00)
To set card swiping period:
Step 1. In main interface, press 【2】or【8】key to move up or down, select time period setup,
and press【#】key. Enter time period interface.
Step 2. Press【2】or 【8】 key to select card swiping period, and press【#】key.
Step 3. Input time period, and press 【#】key. Input any number between 0~127. Screen
displays period.
Step 4. Modify period and press 【#】key.
Step 5. Set other periods. System asks if save it or not.
Step 6. Press【#】key, save config.
When new card set period 1, and user use it to unlock door. According to time period set,
system judge if it is within unlock period. Other periods cannot unlock door.
Note:
Default period is full periods.

4.4.2 Holiday period

Holiday period can be 0~127, a total of 128 periods. When time is any period in 0~127, all cards
or passwords cannot unlock door.
To set holiday period:
Step 1. In time period setup page, press【2】 or【8】 key to select holiday period, and press
【#】key.
Step 2. Input period, and press 【#】key. Input any number between 0~127, such as 1.
Step 3. Modify start time, press 【#】key.
Step 4. Modify end time, press 【#】key. System asks if to save or not.
Step 5. Press 【#】key to save.

16
4.4.3 Mode Period
Mode period has four periods per day, from Monday to Sunday, 7 days a week.
Note:
You shall allocate unlock mode by period, and then mode period config become valid. Unlock
mode config refers to Ch 4.3.

To set mode period:

Step 1. In time period setup interface, press 【2】or【8】key, select mode period, and press
【#】. System displays periods of Monday to Sunday.
Step 2. For example select Monday, and press 【#】key. System displays period 1 page.
Step 3. Config period 1, press 【#】. System displays config mode interface.
Step 4. Press【2】or【8】 key, config mode 1, press【#】key.
Step 5. Config period 2, period 3 and period 4 in sequence. System asks if to save or not.
Step 6. Press 【#】key, save.
Step 7. Config Tuesday to Sunday periods.

System Settings
You can set IP, communication, date, unlock, alarm, password, main card and default in system
settings.

4.5.1 IP Setup
Set current access control IP address, subnet mask and gateway.
Step 1. In main interface, press 【2】or【8】key to select system settings, and press【#】. You
enter system settings page.
Step 2. Press 【2】or【8】key, select IP setup, and press【#】.
Step 3. Modify IP address, subnet mask and gateway, and press 【#】. System asks to save or
not.
Step 4. Press 【#】, save config.

4.5.2 Communication Setup

It sets current access control communication, including RS485 and TCP/IP.

17
Step 1. In system settings interface, press【2】or【8】key, select communication setup, and
press【#】.
Step 2. Press 【2】or【8】key, select communication method, and press【#】.
When you select successfully, there will be a √ next to selected item.

4.5.3 Date Setup

It sets current system date and time.
Step 1. In system settings page, press 【2】or【8】key, select date setup, and press【#】key.
Step 2. Set year, month, hour, minute and second. Press 【#】key. System asks to save it or not.
Step 3. Press 【#】key to save.

4.5.4 Unlock Time

It sets current unlock time.
Step 1. In system settings interface, press 【2】or【8】key, select unlock time, and press【#】.
Step 2. According to range of value, set unlock time, and press 【#】.System asks if to save or
not.
Step 3. Press 【#】key to save.

4.5.5 Alarm Setup

You can enable alarm in alarm setup, and set door overtime. System alarm includes door
overtime alarm, intrusion alarm, forced alarm and vandal-proof alarm.

Table 4-3
Alarm Type Note
Door overtime When access control unlock time is greater than door
alarm overtime, it will alarm.
Door overtime alarm need to set door overtime length,
refer to Ch 4.5.5.2.
Intrusion alarm Enter without card swiping or password, system alarms.
Forced alarm Enter with forced card, system alarms. Refer to Ch
4.2.1.1.
Vandal-proof When device is forced to leave its position, vandal-proof
alarm button will alarm.

18
4.5.5.2 Enable Alarm

For example, to enable forced alarm:

Step 1. In system settings interface, press 【2】 or 【8】 key, select alarm setup, and press
【#】key.
Step 2. Press【2】or【8】key, select intrusion alarm, and press【#】key.
Step 3. Press 【2】or【8】key, select enable or disable. After you successfully selected, there
will be a √.

4.5.5.3 Set Overtime

Door overtime alarm need to set overtime length:

Step 1. In alarm setup interface, press 【2】 or 【8】 key, select door overtime setup, and
press【#】key.
Step 2. Config time, and press 【#】. System asks if to save or not.
Step 3. Press 【#】key to save.

4.5.6 Password Change

You can modify system project password. Project password is 8-digit.
Step 1. In system settings interface, press 【2】 or 【8】 key, select change password, and
press【#】key.
Step 2. Input old password, press 【#】key.
Step 3. Input new password, and press【#】key.
Step 4. Input new password again, and press 【#】key. System asks if to save or not.
Step 5. Press 【#】key to save.

4.5.7 Main Card Management

You can use main card to add new user

4.5.7.1 Modify Main Card

Step 1. In system settings interface, press 【2】 or 【8】 key, select main card management,
and press【#】key.
Step 2. Press 【2】or【8】keym select modify main card, and press【#】key.
19
Step 3. Input card no. or place the card on card swiping area to scan, and press 【#】key. System
asks if to save it or not.
Step 4. Press 【#】key, system says successfully set.

4.5.7.2 Add Card with Main Card

Is means using main card to add user of card. The added user is the same as user in user
management. For example, add general card:
Step 1. In main card interface, press 【2】 or 【8】 key, select add card with main card, and
press【#】key.
Step 2. Press【2】or【8】key, select general card, and press【#】. System asks if to bind password
or not.
Step 3. Select according to actual condition.
 Yes: input password.
 No: system asks if to set period.
Step 4. Press 【#】, set period, and press 【#】key. Time period shall match card swiping period
in time period setup. Refer to Ch 4.4.1.
Step 5. Press 【#】key, set term of validity, and press 【#】.
After you finish, system asks you to swipe main card.
Step 6. Place main card on card swiping area to scan. System prompts main card mode.
Step 7. Place card to add on card swiping area to scan. System will say successfully added.

4.5.8 Default
You can restore card swiping period, holiday period and mode time to default, or restore all info
to default.
To restore card swiping period:
Step 1. In system settings interface, press 【2】 or 【8】key, select default, and press【#】
key.
Step 2. Press 【2】 or【8】 key, select card swiping period, and press【#】key.
System asks if to restore or not.
Step 3. Press 【#】key to restore.

Reboot System
You can reboot current device host under system reboot.

20
Step 1. In main interface, press 【2】or【8】key, select system reboot, and press【#】. System
asks if to reboot or not.
Step 2. Press【#】key to reboot, and press【*】to cancel.

Local Info
You can view current device card quantity, card swiping record, password quantity, alarm record,
communication, IP address, MAC address and version info.
Step 1. In main interface, press 【2】or【8】key, select local info, and press【#】key.
Step 2. View card quantity, card swiping record, password quantity, alarm record,
communication, IP address, MAC address and version info.

Note:
 This manual is for reference only. Slight difference may be found in user interface.
 All the designs and software here are subject to change without prior written notice.
 All trademarks and registered trademarks are the properties of their respective
owners.
 If there is any uncertainty or controversy, please refer to the final explanation of us.
 Please visit our website or contact your local service engineer for more information.

21