Scribd Logo
Upload

Welcome to Scribd!

  • 6 views

    Instructions GingerBreadMan Ornament

    Uploaded by

    vivigarvasionigro

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Instructions GingerBreadMan Ornament

    Uploaded by

    vivigarvasionigro
    6 views5 pages

    Original Title

    Instructions_GingerBreadMan_Ornament

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    6 views5 pages

    Instructions GingerBreadMan Ornament

    Uploaded by

    vivigarvasionigro

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    thanks for your purchase of the

    GINGERBREAD MAN ORNAMENT


           
         
            
           (s
       ).    
                   

                


             
              
         

      


    about this model
         3.5 in. x 0.5 in. x 4 in.

     

    materials needed
    These are the material suggestions if you want to make the model as shown in the photo.
    You can use any material or color substitutions that you would like, as long as they are in the
    same quantities as the material that you are substituting.

    • Glue. Preferably the liquid kind. Hot glue, glue sticks, and adhesive tape either make a
    mess of your model or just don’t stick well enough to hold it together.
    • 1 sheet Light Brown cardstock - 12” x 12” or 8.5” x 11”
    • 1 sheet White cardstock - 12” x 12” or 8.5” x 11”
    • 1 sheet Green cardstock - 12” x 12” or 8.5” x 11”
    • 1 sheet Red cardstock - 12” x 12” or 8.5” x 11”
    • 5” of ribbon
    • Matte Mod Podge
    • Stiff bristle brush

    fold lines & preparation


    This design may have both mountain and valley fold lines. This means that some lines will
    fold in and others will fold out depending on the design. You’ll need to watch the line
    pattern and be sure you are folding the paper in the right direction.

    Mountain Fold Line

    Valley Fold Line

    Mountain Fold Valley Fold


    piece identification guide
    Take a moment to identify and label the pieces of the model on the reverse side after they have been cut out. ( The Piece Identification Guide
    is only meant to be used as a reference for identifying pieces and should not be cut out.)

    Light Brown White

    B1

    Green

    Red

    B2

    B3
    page 1

    1 2

    Begin assembly by gluing the white, red, and green pieces to the back It should look like this when flipped over.
    of the gingerbread man as shown.

    3 4

    B1 B2 B3

    Glue the ends of B1, B2, and B3 together as shown. NOTE: There is a Then start working your way around gluing the tabs to the face of the
    number cut into the end tabs of each piece, indicating which piece it ornament.
    is.

    5 6

    Cut a piece of ribbon to 5 inches and insert the ends through the slot Hot glue the ends to the inside of the ornament as shown.
    on the top of the ornament.
    page 2

    7 8

    Glue the back flap down. Step 9 is about applying a texture to your ornament. This enhances
    the look but also protects your model. You’ll need Matte Mod Podge
    and a stiff bristle brush. If you are not texturing your model you can
    skip to Step 10.

    9 10

    Begin applying the Mod Podge using a stippling action. The more you Congratulations! You are finished.
    apply, the heavier your texture will be.

    You might also like