#include <SPI.

h>
#include <MFRC522.h>
//--------------------------------------------------
//GPIO 0 --> D3
//GPIO 2 --> D4
const uint8_t RST_PIN = D3;
const uint8_t SS_PIN = D4;
//--------------------------------------------------
MFRC522 mfrc522(SS_PIN, RST_PIN);
MFRC522::MIFARE_Key key;
//--------------------------------------------------
/* Be aware of Sector Trailer Blocks */
int blockNum = 4;
/* Create array to read data from Block */
/* Length of buffer should be 4 Bytes
more than the size of Block (16 Bytes) */
byte bufferLen = 18;
byte readBlockData[18];
//--------------------------------------------------
MFRC522::StatusCode status;
//--------------------------------------------------

void setup()
{
//------------------------------------------------------
//Initialize serial communications with PC
Serial.begin(9600);
//------------------------------------------------------
//Initialize SPI bus
SPI.begin();
//------------------------------------------------------
//Initialize MFRC522 Module
mfrc522.PCD_Init();
Serial.println("Scan a MIFARE 1K Tag to write data...");
//------------------------------------------------------
}

/
***********************************************************************************
*****************
* loop() function

***********************************************************************************
*****************/
void loop()
{
//------------------------------------------------------------------------------
/* Prepare the ksy for authentication */
/* All keys are set to FFFFFFFFFFFFh at chip delivery from the factory */
for (byte i = 0; i < 6; i++){
key.keyByte[i] = 0xFF;
}
//------------------------------------------------------------------------------
/* Look for new cards */
/* Reset the loop if no new card is present on RC522 Reader */
if ( ! mfrc522.PICC_IsNewCardPresent()){return;}
//------------------------------------------------------------------------------
/* Select one of the cards */
if ( ! mfrc522.PICC_ReadCardSerial()) {return;}
//------------------------------------------------------------------------------
Serial.print("\n");
Serial.println("**Card Detected**");
/* Print UID of the Card */
Serial.print(F("Card UID:"));
for (byte i = 0; i < mfrc522.uid.size; i++){
Serial.print(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " ");
Serial.print(mfrc522.uid.uidByte[i], HEX);
}
Serial.print("\n");
/* Print type of card (for example, MIFARE 1K) */
Serial.print(F("PICC type: "));
MFRC522::PICC_Type piccType = mfrc522.PICC_GetType(mfrc522.uid.sak);
Serial.println(mfrc522.PICC_GetTypeName(piccType));

//------------------------------------------------------------------------------
byte buffer[18];
byte len;
//wait until 20 seconds for input from serial
Serial.setTimeout(20000L);
//MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM
Serial.println(F("---------------------------------------"));
Serial.println(F("Enter Student Roll No, ending with #"));
len = Serial.readBytesUntil('#', (char *) buffer, 16);
//add empty spaces to the remaining bytes of buffer
for (byte i = len; i < 16; i++) buffer[i] = ' ';
blockNum = 4;
WriteDataToBlock(blockNum, buffer);
ReadDataFromBlock(blockNum, readBlockData);
dumpSerial(blockNum, readBlockData);
//MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM
Serial.println(F("---------------------------------------"));
Serial.println(F("Enter Student Name, ending with #"));
len = Serial.readBytesUntil('#', (char *) buffer, 16);
for (byte i = len; i < 16; i++) buffer[i] = ' ';
blockNum = 5;
WriteDataToBlock(blockNum, buffer);
ReadDataFromBlock(blockNum, readBlockData);
dumpSerial(blockNum, readBlockData);
//MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM
Serial.println(F("---------------------------------------"));
Serial.println(F("Enter Department, ending with #"));
len = Serial.readBytesUntil('#', (char *) buffer, 16);
for (byte i = len; i < 16; i++) buffer[i] = ' ';
blockNum = 6;
WriteDataToBlock(blockNum, buffer);
ReadDataFromBlock(blockNum, readBlockData);
dumpSerial(blockNum, readBlockData);
//MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM
Serial.println(F("---------------------------------------"));
Serial.println(F("Enter Year, ending with #"));
len = Serial.readBytesUntil('#', (char *) buffer, 16);
for (byte i = len; i < 16; i++) buffer[i] = ' ';
blockNum = 8;
WriteDataToBlock(blockNum, buffer);
 ReadDataFromBlock(blockNum, readBlockData);
dumpSerial(blockNum, readBlockData);
Serial.println(F("---------------------------------------"));
Serial.println(F("Enter Address, ending with #"));
len = Serial.readBytesUntil('#', (char *) buffer, 16);
for (byte i = len; i < 16; i++) buffer[i] = ' ';
blockNum = 9;
WriteDataToBlock(blockNum, buffer);
ReadDataFromBlock(blockNum, readBlockData);
dumpSerial(blockNum, readBlockData);
}

/
***********************************************************************************
*****************
* Writ() function

***********************************************************************************
*****************/
void WriteDataToBlock(int blockNum, byte blockData[])
{
//Serial.print("Writing data on block ");
//Serial.println(blockNum);
//------------------------------------------------------------------------------
/* Authenticating the desired data block for write access using Key A */
status = mfrc522.PCD_Authenticate(MFRC522::PICC_CMD_MF_AUTH_KEY_A, blockNum,
&key, &(mfrc522.uid));
if (status != MFRC522::STATUS_OK){
Serial.print("Authentication failed for Write: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
//------------------------------------------------------------------------------
else {
//Serial.print("Authentication OK - ");
}
//------------------------------------------------------------------------------
/* Write data to the block */
status = mfrc522.MIFARE_Write(blockNum, blockData, 16);
if (status != MFRC522::STATUS_OK) {
Serial.print("Writing to Block failed: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else {
//Serial.println("Write OK");
}
//------------------------------------------------------------------------------
}

/
***********************************************************************************
*****************
* ReadDataFromBlock() function
***********************************************************************************
*****************/
void ReadDataFromBlock(int blockNum, byte readBlockData[])
{
//Serial.print("Reading data from block ");
//Serial.println(blockNum);
//----------------------------------------------------------------------------
/* Prepare the ksy for authentication */
/* All keys are set to FFFFFFFFFFFFh at chip delivery from the factory */
for (byte i = 0; i < 6; i++) {
key.keyByte[i] = 0xFF;
}
//------------------------------------------------------------------------------
/* Authenticating the desired data block for Read access using Key A */
status = mfrc522.PCD_Authenticate(MFRC522::PICC_CMD_MF_AUTH_KEY_A, blockNum,
&key, &(mfrc522.uid));
//------------------------------------------------------------------------------
if (status != MFRC522::STATUS_OK){
Serial.print("Authentication failed for Read: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else {
//Serial.print("Authentication OK - ");
}
//------------------------------------------------------------------------------
/* Reading data from the Block */
status = mfrc522.MIFARE_Read(blockNum, readBlockData, &bufferLen);
if (status != MFRC522::STATUS_OK){
Serial.print("Reading failed: ");
Serial.println(mfrc522.GetStatusCodeName(status));
return;
}
else {
//readBlockData[16] = ' ';
//readBlockData[17] = ' ';
//Serial.println("Read OK");
}
//------------------------------------------------------------------------------
}

/
***********************************************************************************
*****************
* dumpSerial() function

***********************************************************************************
*****************/
void dumpSerial(int blockNum, byte blockData[])
{
Serial.print("\n");
Serial.print("Data saved on block");
Serial.print(blockNum);
Serial.print(": ");
for (int j=0 ; j<16 ; j++){
Serial.write(readBlockData[j]);
 }
Serial.print("\n");

//Empty readBlockData array