GBNA/GBRU Error Code Specification

B006-6524-A000
Issue 6
Nov 2016
Copyright and Trademark Information

The products described in this document are copyrighted works of NCR Corporation.

NCR and Personas are trademarks of NCR Corporation.

IBM and OS/2 are trademarks of International Business Machines Corporation in the United States, other countries, or both.
All other trademarks are the property of their respective owners.

Disclaimer:

It is the policy of NCR Corporation to improve products as technology, components, software and firmware become available. NCR
therefore reserves the right to change specifications without prior notice.

All features, functions and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR
office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organisation and value of this book.

Address correspondence to:

NCR Financial Solutions Group Ltd

Information Solutions Feedback
Discovery Centre
3 Fulton Road
Dundee
Scotland
DD2 4SW

© 2004, 2006, 2007, 2010, 2013, 2016

By NCR Corporation
Duluth, Georgia, USA
All Rights Reserved
 1 2 3 4

A A

ERROR CODE LIST

of
B
GBNA / GBRU B

C C

D D

E E

25 2016.06.22 Kojima Kojima Satou Rev.25 TITLE

24 2016.01.19 Kojima Kojima Satou Rev.24 ERROR CODE LIST of GBNA/GBRU
23 2015.09.02 Kojima Kojima Wada Rev.23
22 2015.03.18 Kojima Kojima Wada Rev.22 DRAW.NO. CUST
21 2014.09.09 Saji Kojima Wada Rev.21 A3KD02160-A002
20 2013.04.24 Saji Kojima Wada Rev.20
19 2012.05.29 Saji Kojima Wada Rev.19
FUJITSU FRONTECH LIMITED SHEET 001 / 063
DESIG. 2004.09.17 Kojima CHECK Kojima APPR. Endo
 CHANGE SHEET

Rev. Date DESCRIPTION of CHANGE

1 9/17/2004 Initial Release.
2 9/28/2004 Add error code. (6604)
Fix sensor name. (FF0D,FF5D)
3 10/6/2004 Add error code. (3201,6F71)
4 10/13/2004 Add command code. (ES)
Add error code. (6103)
5 11/29/2004 Add related solenoid and sensor.(6180)
A location is added to all error messages.
6 2/15/2005 Change error messages(1001,2020).
Add error code. (3501,3502,3503,3510)
Add "Cause/Check&Inspect/Solution". (25**,29**)
7 3/11/2005 Add error code (6703,6704)
8 5/20/2005 Add error message (72A0)
9 1/18/2006 Add error code (E211,E30B)
10 4/21/2006 Add error code (E212,E213,E30C,E30D)
Add command code. (LN)
11 7/26/2006 Add error code (6F88)
12 12/15/2006 Add error code (6C02,6C11)
Add 'How to when to detect error', 'Sensor', and 'Related FRU'(7C01,7C81)
13 2/15/2007 Add error code
(8180,8181,8400,8E80,9180,9181,9400,9E80,A180,A181,A400,AE80,B180,B181,B400,BE80,E112-
E115,E214-E217,E30E-E311,E411-E414,F64E-F651,F727-F72A)
14 7/6/2007 Add error code (6605,6C21)
Add command code. (CI,PD,BE)
15 10/9/2008 Add error code (3C02)
16 2/5/2009 Add error code (3414)
17 9/7/2010 Add error code (81FF,91FF,A1FF,B1FF)
Change the format in 4. Error code and FRU name
18 6/30/2011 Add error code (6606)
19 5/29/2012 Add command code. (LB,BL)
Add error code (2724,2725,2710,2711,2712)
20 4/24/2013 Add error code. (2C00)
Add 'How to when to detect error' and 'Sensor'.(6600)
Add 'Sensor'.(7681)
Change error messages.(F710,F711,F712,F713,F717,F718,F719,F71A)
21 9/9/2014 Add error code. (162A)
22 3/18/2015 Add to 'How to when to detect error'.(F629)
Add to 'Related FRU Check & Replace Other'.(6603,6C00,6F70,E106)
Add to 'Connector'.(4009,6222)
Add PDMG to 'Motor/Solenoid'.(6700)
Add command code. (M1,M2,M3,M6)
Add FRU code. (FPCB)
Subdivide 25**,29** error.
Sort 27** error.
Add error code.
(162B,162C,162D,162E,2713,2714,2715,2716,2717,2718,2719,271A,271B,271C,5***,6610,6611,6612
,6613,6614,6615,6616,6617,6618,6619,661A,661B,661C,661D,661E,6710,6720,6730,6731,6740,6750)

23 9/2/2015 Add command code. (WP)

Add error code.(162F)
24 1/19/2016 Add command code. (AC,AD)
Add error code.(1630,16F0,1800,1801,3F00,3F01,3F02,3F03)
Add probable causes of errors. (016,017)
25 6/22/2016 Add error code. (3F04)

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/1
 INTRODUCTION

This specification describes the error code of Global Bunch Note Acceptor (hereinafter “GBNA”)
and Global Bill Recycle Unit (hereinafter “GBRU”).

All Rights Reserved, Copyright FUJITSU FRONTECH LIMITED 2003-2016

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/1
1. Error Code System

An error code consists of 8 digits of alpha numeric.

An error code is divided into 3 section as it is shown in below.

XXXX + YY + ZZ
Command code + Category + Detail

First section shows the command code.

Second section shows the category of detected error together with the place of detection.
Third section shows the detailed information.

When an error occurs, Category and Detail include an error code are displayed on the 7 segments LED display
located in the Upper PCB board as shown in below.

1 second
Y. Y.
Blink 0.5 seconds 2 seconds

1 second
Z. Z.

When the command is received from host, stops to display an error code.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/1
2. Display image on 7segments LED.

0 1 2 3 4 5 6 7 8 9 A B C D E F H -

Display code on 7segments LED.

code substance

00 generally *
generally *
* : The code is changed when ST swich is pushed for 3 seconds. (Dispense enable switch)
H0 checking sum value of IPL-program
H1 checking inside memory
H2 checking external memory
H3 checking BOOT-program
H4 checking file-system
-0 BOOT-program deficit
-1 Main-program deficit
-2 downloading by USB
-3 downloading by SCI
-4 system down
-5 defect of file-system
-6 parity error
-7 memory error
-8 undefined interrupt
-9 general illegal instructions/illegal slot instructions
-A address error
-B NMI/watch dog error
-C sum error for main-program
-D sum error for BOOT-program
-E send error on USB
-F sum error for IPL-program

DB started debugger in BOOT-program

DE ended debugger

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/1
3. Command Code List

No. Code (H) Command Summary

1 5254 RT Reset (Software reset)
2 4854 HT Halt (abort) command
3 5354 ST Read status of unit
4 4C44 LD Load program
5 4C45 LE End to load program
6 454B EK Set encryption key
7 4650 FP Set fixed parameter
8 4350 CP Set cassette parameter
9 4944 ID Read identification of unit
10 4C4E LN Load serial number of unit
11 4352 CR Correct counter of note
12 5349 SI Read statistics information
13 4943 IC Clear statistics information
14 4C49 LI Load statistics information
15 5342 SB Read BV information
16 5652 VR Read validation order information
17 5347 SG Read signature of note
18 534E SN Read serial number of note
19 5049 PI Read picture of note
20 4349 CI Read cheque image
21 4C42 LB Load black list
22 424C BL Read black list
23 4C47 LG Read log data
24 4D31 M1 Write ATM vendor FRU data
25 4D32 M2 Write ATM data
26 4D33 M3 Write replacing data
27 4D36 M6 Read ATM data
28 4143 AC Authenticate communication
29 4144 AD Read communication authentication data
30 5359 SY Power off
31 4956 IV Accept
32 4450 DP Deposit
33 424B BK Back accepted notes
34 5743 WC Dispense
35 5050 PP Present preparation
36 544F TO Present
37 534F SO Shutter open
38 5343 SC Shutter close forcedly
39 5543 UC Reconciliation
40 4243 BC Back notes from temporary cassette
41 434C CL Collect data of note
42 534B SK Mechanical preparation
43 524A RJ Capture / Reject
44 4D52 MR Mechanical reset
45 4D4A MJ Jam clear, Reject and Mechanical reset
46 4A41 JA Jam clear for accept
47 4150 AP Auto present
48 5253 RS Remote RAS
49 4442 DB Debug
50 4553 ES Escape note (Auto purge)
51 5044 PD Pre-deposit
52 4245 BE Back pre-deposited notes to the Escrow
53 5750 WP Withdraw notes at the front

Refer to "DATA LEVEL INTERFACE of GBNA/GBRU" about contents of command.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/1
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
0C** Firmware illegal functional error
0C00 <Firmware>return from system-management-task. System-management-task has completed. S or H LPCB 013,307
0C01 <Firmware>unjust augments for the function. Arguments of the function was invalid. S or H LPCB 013,307
Pre-acceptor located in an unexpected position when required to
operate.
0C02 <Firmware>Event generating besides assumption Unexpected values detected inside firmware during command S or H LPCB 013,307
processing.
0C03 <Firmware>not decide destination of note No suitable destination found for a note to be stored. S or H LPCB 013,307
0C10 <Firmware>not allocate memory for TCB. Could not allocate memory for TCB. S or H LPCB 013,307
0C11 <Firmware>not allocate memory for packet of task. Could not allocate memory for packet of task. S or H LPCB 013,307
0C12 <Firmware>not allocate memory for packet of transfer Could not allocate memory for packet of transfer process. S or H LPCB 013,307
process.
0C13 <Firmware>not initialise for timer-control. Could not allocate memory for timer-control. S or H LPCB 013,307
0C20 <Firmware>timer-set impossible. Could not set timer because it has been used in excess of the S or H LPCB 013,307
maximum.
0C21 <Firmware>setpkt impossible. Could not set packet because packet ID had been corrupted. S or H LPCB 013,307
Could not set packet because it had been used in excess of the
maximum.
0C30 <Firmware>Operation is impossible.(by remain) Could not execute a command because notes remained in several H PAC ESC or SEP 013,307
locations.
0C40 <PCB>FLASH-rom erase impossible Could not erase a file in Flash-ROM. H LPCB 307
0C41 <PCB>FLASH-rom write impossible Could not write a file into Flash-ROM. H LPCB 307
0C50 <PCB>Memory break. The sum in a program on RAM did not match. H LPCB 307
0C60 <Firmware>Command time limit over (1st). Command processing did not complete within the specified time H LPCB 013,307
leading to timeout.
0C61 <Firmware>Command time limit over (2nd). Second timeout caused by failure to complete a command after the H LPCB 013,307
first timeout.
1*** relate with Host Interface Error
1001 <Boot>Main-Firmware is not installed. Received RT command during BOOT program before H or S LPCB 014,307
downloading MAIN firmware.
1101 <Boot>Boot cannot read and write fail Unable to read/write MAIN firmware on Flash-ROM during H LPCB 014,307
BOOT program.
1102 <Boot>unjust check code of file The sum in an overall program did not match when downloading H LPCB 014,307
firmware.
1201 <Host Interface>Boot receives invalid command Received invalid command in BOOT program. H LPCB 014,307
1301 <Host Interface>unjust data length(BOOT) Frame Length was less than 6 bytes when receiving a command in H or C LPCB USB 313,314
BOOT program.
Frame Length exceeded the maximum length when receiving a
command in BOOT program.
Frame Length was smaller than Message Length when receiving a
command in BOOT program.
Message Length was not equal to the sum of Message Header and
Data Block when receiving a command in BOOT program.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 1 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
1302 <Host Interface>unjust data format(BOOT) Message Header of a command received in BOOT program H or C LPCB USB 313,314
contained an invalid value.
Classification of data was invalid when receiving a command in
BOOT program.
1303 <Host Interface>unjust number of data block(BOOT) Number of data block received in BOOT program was invalid. H or C LPCB USB 313,314
1304 <Host Interface>unjust data sum(BOOT) The sum of a command received in BOOT program did not match. H or C LPCB USB 313,314

1311 <Host Interface>unjust parameter H0(BOOT) A Block number of LD or LE commands was an unexpected value H or C LPCB USB 313,314
in BOOT program.
1500 <Host Interface>Receive invalid command Received an invalid command. H or C LPCB USB 313,314
1600 <Host Interface>unjust data classification of data Classification of data was invalid when receiving a command. H or C LPCB USB 313,314
1601 <Host Interface>unjust data length Frame Length was less than 6 bytes when receiving a command. H or C LPCB USB 313,314
Frame Length exceeded the maximum length when receiving a
command.
Frame Length was smaller than Message Length when receiving a
command.
Message Length was not equal to the sum of Message Header and
Data Block when receiving a command.
1602 <Host Interface>unjust data format Message Header of a received command contained an invalid H or C LPCB USB 313,314
value.
1603 <Host Interface>unjust number of data block Number of data block was invalid when receiving a command. H or C LPCB USB 313,314
1604 <Host Interface>unjust data sum The sum of a command received did not match. H or C LPCB USB 313,314
1620 <Host Interface>unjust parameter A1 Parameter A1 was set to an invlalid value when receiving a S or H LPCB 013
command.

1621 <Host Interface>unjust parameter A2 Parameter A2 was set to an invlalid value when receiving a S or H LPCB 013
command.

1622 <Host Interface>unjust parameter A5 Parameter A5 was set to an invlalid value when receiving a S or H LPCB 013
command.

1623 <Host Interface>unjust parameter A6 Parameter A6 was set to an invlalid value when receiving a S or H LPCB 013
command.

1626 <Host Interface>unjust parameter A9 Parameter A9 was set to an invlalid value when receiving a S or H LPCB 013
command.

1627 <Host Interface>unjust parameter AZ Parameter AZ was set to an invlalid value when receiving a S or H LPCB 013
command.

1628 <Host Interface>unjust parameter H0 Parameter H0 was set to an invlalid value when receiving a S or H LPCB 013
command.

1629 <Host Interface>unjust parameter A0 Parameter A0 was set to an invlalid value when receiving a S or H LPCB 013
command.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 2 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
162A <Host Interface>unjust parameter AE Parameter AE was set to an invlalid value when receiving a S or H LPCB 013
command.

162B <Host Interface>unjust parameter P1 Parameter P1 was set to an invlalid value when receiving a S or H LPCB 013
command.

162C <Host Interface>unjust parameter P2 Parameter P2 was set to an invlalid value when receiving a S or H LPCB 013
command.

162D <Host Interface>unjust parameter P3 Parameter P3 was set to an invlalid value when receiving a S or H LPCB 013
command.

162E <Host Interface>unjust parameter P0 Parameter P0 was set to an invlalid value when receiving a S or H LPCB 013
command.

162F <Host Interface>unjust parameter A4 Parameter A4 was set to an invlalid value when receiving a S or H LPCB 013
command.

1630 <Host Interface>unjust parameter AF Parameter AF was set to an invlalid value when receiving a S or H LPCB 013
command.

1640 <Host Interface>abnormalities in download sequence LE command was received prior to LD command. S or H LPCB 013
16F0 <Host Interface>Not available RAS command The specified RAS command is not available. S or H LPCB 013,017,307
1700 <Host Interface>un-setting parameter A1 A1 parameter not specified yet when receiving a command that H LPCB 013
requires A1 parameter.
1800 <Host Interface>Invalid encryption The encryption was invlalid when receiving a command. S or H LPCB 013,017,307
1801 <Host Interface>No parameter AF There was no parameter AF when receiving a command. S or H LPCB 013,017,307
1C00 <Host Interface>Un-setting payment password. Password for dispense not entered when starting RAS. O Operatipon 015
1C01 <Host Interface>Un-setting calculation password. Password for counting not entered when starting RAS. O Operatipon 015
1E00 <USB>USB connector pull out USB VBUS signal was found low during command processing. H or C LPCB USB 313,314,307
1E01 <USB>USB bus reset detect USB bus reset was detected during command processing. H or C LPCB USB 313,314,307
1E02 <USB>Timeout of USB transmission. Could not transmit a response within the specified time. H or C LPCB USB 313,314,307
2*** relate with BV Error
2001 <Firmware>It cannot receipt request data that it is BV task was already in operation when requesting to BV task. S or H BV LPCB 013
under bill validation.
2004 <BV>Timeout of BV response. No response sent from BV within the specified time when H or C BV LPCB BV LAN 315-318,011,307
requesting a command.
2005 <BV>unjust BV data sum The sum of a response received from BV did not match. H or C BV LPCB BV LAN 315-318,011,307
2006 <BV>unjust BV data length Data length invalid when receiving a response from BV. H or C BV LPCB BV LAN 315-318,011,307
2007 <BV>BV reset failure Received a response other than reset command after sent a reset H BV LPCB 315-318,011,307
command to BV.
No response informed by BV within the specified time resulting in
timeout when BV was requested a reset command.
There occured an alarm other than BV cover open/Note remain at
Alarm read command after BV reset command.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 3 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
2008 <BV>Sending data from BRU and Receiving data from Mismatch between data send command and data receive command H or C BV BV LAN 315-318,011
BV is discode. when receiving a response from BV.
A response from BV was UMG.
2009 <BV>Sending block number from BRU and Receiving Block number of a response to BV commands (RVR,RGP) was H or C BV BV LAN 315-318,011
block number from BV is discode. unexpected values.
2020 <BV>BV program is not installed. BV firmware version was not set after executing BV reset H BV 014,011
command.

2100 <BV>There is no response from BV RR command did not returned from BV after sending TEST H or C BV LPCB BV LAN 315-318,011,307
command. or BPWR
RR command did not returned from BV after sending a command.
Could not send by LAN LSI error when sending a packet to BV.
Lan task was Initialize state when sending a command to BV.

2300 <BV>Over VD from BV. Number of validation data exceeded number of notes detected at H BV 315-318,011
BVIN during note validation.
25** <BV>BV unit failure. ( ** : 2digit in VD error code. xx Received validation data during bill validation that indicates H or S BV 001,002,004,304,31
in VD data'9Exx' ) further validation impossible. 5-318,011
2501 <BV>BV system error No response in discrimination parts S BV 001,002,004,304,31
5-318,011
2502 <BV>BV system error No response in discrimination parts S BV 001,002,004,304,31
5-318,011
2503 <BV>BV system error No response in discrimination parts S BV 001,002,004,304,31
5-318,011
2504 <BV>BV system error No response in discrimination parts S BV 001,002,004,304,31
5-318,011
2505 <BV>BV system error No response in discrimination parts S BV 001,002,004,304,31
5-318,011
2507 <BV>BV system error Internal interface error S BV 001,002,004,304,31
5-318,011
2508 <BV>BV system error No response in discrimination parts S BV 001,002,004,304,31
5-318,011
2509 <BV>BV system error Power error S BV 001,002,004,304,31
5-318,011
250A <BV>BV Check Note Error Error of medium S BV Check Note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
250F <BV>BV system error Recalibration error S BV BV Check Note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2510 <BV>Validation mode specified error During validation S or H BV FW BV 001,002,004,304,31
Download 5-318,011
2511 <BV>Template error Template for notes S or H BV FW BV 001,002,004,304,31
<The discrimination of the test note was directed. > Download 5-318,011
2512 <BV>Template error Template for test notes S or H BV FW BV 001,002,004,304,31
<The discrimination of the note was directed. > Download 5-318,011
2513 <BV>Template error invalid validation parameter S or H BV 001,002,004,304,31
5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 4 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
2514 <BV>Template error invalid validation parameter S or H BV 001,002,004,304,31
5-318,011
251E <BV>Hard error Thickness sensor error H BV 001,002,004,304,31
5-318,011
251F <BV>Hard error Image sensor error H BV 001,002,004,304,31
5-318,011
2520 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2521 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2522 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2523 <BV>Sensor error magnetic sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2524 <BV>Sensor error magnetic sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2525 <BV>Sensor error UV sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2526 <BV>Sensor error UV sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2527 <BV>Sensor error Thickness sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2530 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2531 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2532 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2533 <BV>Sensor error magnetic sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2534 <BV>Sensor error magnetic sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2535 <BV>Sensor error Image sensor error or UV sensor error. H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2536 <BV>Sensor error Image sensor error or UV sensor error. H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2537 <BV>Sensor error Thickness sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2538 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2539 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
253A <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
253B <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 5 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
253C <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
253D <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
253E <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
253F <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2540 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2541 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2542 <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2543 <BV>Sensor error magnetic sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2544 <BV>Sensor error magnetic sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2545 <BV>Sensor error Image sensor error or UV sensor error. H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2546 <BV>Sensor error Image sensor error or UV sensor error. H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2547 <BV>Sensor error Thickness sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2548 <BV>Sensor error Image sensor error or Soil of BV Check Note. H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
2549 <BV>Sensor error Image sensor error or Soil of BV Check Note. H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
254A <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
254B <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
254C <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
254D <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
254E <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
254F <BV>Sensor error Image sensor error H or O BV BV Check note 001,002,004,304,31
< Only when BV Chcek Note is used, this is detected. > 5-318,011
25FC <BV>BV system error Memory error H BV 001,002,004,304,31
5-318,011
25FD <BV>BV system error Controller error H BV 001,002,004,304,31
5-318,011
25FE <BV>BV system error Parameter error H BV 001,002,004,304,31
5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 6 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
2600 <BV>The taken VD data and the validation result Mismatch of validation data between the one stored in BRU and H BV 315-318,011
which came from BV did not suit. the one read from BV.
27** <BV>Received a negative response relate with BV. H BV LAN cable BV LAN
( ** : BV command name is as follows )
2710 <BV>( RNI : Read Serial No. data ) Received a negative response to RNI command from BV. H BV LAN cable BV LAN 315-318,011
2711 <BV>( LBL : Load black list ) Received a negative response to LBL command from BV. H BV LAN cable BV LAN 315-318,011
2712 <BV>( RBL : Read black list ) Received a negative response to RBL command from BV. H BV LAN cable BV LAN 315-318,011
2713 <BV>( CFRU : Clear FRU data ) Received a negative response to CFRU command from BV. H BV LAN cable BV LAN 315-318,011
2714 <BV>( WFTEC : Write FRU data ) Received a negative response to WFTEC command from BV. H BV LAN cable BV LAN 315-318,011
2715 <BV>( WNCR : Write ATM vendor FRU data ) Received a negative response to WNCR command from BV. H BV LAN cable BV LAN 315-318,011
2716 <BV>( WATM : Write ATM data ) Received a negative response to WATM command from BV. H BV LAN cable BV LAN 315-318,011
2717 <BV>( WERR : Write ATM error data ) Received a negative response to WERR command from BV. H BV LAN cable BV LAN 315-318,011
2718 <BV>( WID : Write Engineer ID data ) Received a negative response to WID command from BV. H BV LAN cable BV LAN 315-318,011
2719 <BV>( WREA : Write Reason data ) Received a negative response to WREA command from BV. H BV LAN cable BV LAN 315-318,011
271A <BV>( WREP : Write Repair data ) Received a negative response to WREP command from BV. H BV LAN cable BV LAN 315-318,011
271B <BV>( RFRU : Read FRU data ) Received a negative response to RFRU command from BV. H BV LAN cable BV LAN 315-318,011
271C <BV>( RATM : Read ATM data ) Received a negative response to RATM command from BV. H BV LAN cable BV LAN 315-318,011
2720 <BV>( RSG : Read feature image data ) Received a negative response to RSG command from BV. H BV LAN cable BV LAN 315-318,011
2721 <BV>( RNS : Read the number of feature image data ) Received a negative response to RNS command from BV. H BV LAN cable BV LAN 315-318,011
2722 <BV>( RNO : Read Serial No. ) Received a negative response to RNO command from BV. H BV LAN cable BV LAN 315-318,011
2723 <BV>( MOD : Change the connetion mode ) Received a negative response to MOD command from BV. H BV LAN cable BV LAN 315-318,011
2724 <BV>( RCQ : Read Cheque image ) Received a negative response to RCQ command from BV. H BV LAN cable BV LAN 315-318,011
2725 <BV>( RGR2 : Read note image for Data collection) Received a negative response to RGR2 command from BV. H BV LAN cable BV LAN 315-318,011
2731 <BV>( RRT : Reset ) Received a negative response to RRT command from BV. H BV LAN cable BV LAN 315-318,011
2732 <BV>( TM : Time setting ) Received a negative response to TM command from BV. H BV LAN cable BV LAN 315-318,011
2733 <BV>( SRE : Sensor correction ) Received a negative response to SRE command from BV. H BV LAN cable BV LAN 315-318,011
2736 <BV>( CSG : Clear signature ) Received a negative response to CSG command from BV. H BV LAN cable BV LAN 315-318,011
2737 <BV>( RGR : Read image data ) Received a negative response to RGR command from BV. H BV LAN cable BV LAN 315-318,011
2738 <BV>( CAM : Clear all memory area ) Received a negative response to CAM command from BV. H BV LAN cable BV LAN 315-318,011
2739 <BV>( DINF : Validation in-process information ) Received a negative response to DINF command from BV. H BV LAN cable BV LAN 315-318,011
273A <BV>( WGR : Write image data ) Received a negative response to WGR command from BV. H BV LAN cable BV LAN 315-318,011
273B <BV>( SDI : Dummy validation ) Received a negative response to SDI command from BV. H BV LAN cable BV LAN 315-318,011
273C <BV>( PSM : Power save mode setting ) Received a negative response to PSM command from BV. H BV LAN cable BV LAN 315-318,011
273D <BV>( RBI : Read Validation available denomination Received a negative response to RBI command from BV. H BV LAN cable BV LAN 315-318,011
information )
273E <BV>( SBI : Specify Validation available Received a negative response to SBI command from BV. H BV LAN cable BV LAN 315-318,011
denomination )
273F <BV>( RGP : Read all imag data ) Received a negative response to RGP command from BV. H BV LAN cable BV LAN 315-318,011
2740 <BV>( RRV : Read revision information area ) Received a negative response to RRV command from BV. H BV LAN cable BV LAN 315-318,011
2741 <BV>( RUN : Read device information area ) Received a negative response to RUN command from BV. H BV LAN cable BV LAN 315-318,011
2743 <BV>( RAL : Read alarm information area ) Received a negative response to RAL command from BV. H BV LAN cable BV LAN 315-318,011
2745 <BV>( RST : Read statistics information area ) Received a negative response to RST command from BV. H BV LAN cable BV LAN 315-318,011
2746 <BV>( RVR : Read validation information on a Received a negative response to RVR command from BV. H BV LAN cable BV LAN 315-318,011
transaction basis )
2747 <BV>( RVR2 : Read final validation information on a Received a negative response to RVR2 command from BV. H BV LAN cable BV LAN 315-318,011
transaction basis )

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 7 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
2748 <BV>( RMG : Read message information area ) Received a negative response to RMG command from BV. H BV LAN cable BV LAN 315-318,011
274B <BV>( SON : Insertion/transit sensor ON ) Received a negative response to SON command from BV. H BV LAN cable BV LAN 004,315-318,011
274C <BV>( SOF : Insertion/transit sensor OFF ) Received a negative response to SOF command from BV. H BV LAN cable BV LAN 315-318,011
2752 <BV>( RVP : Read recognition information area ) Received a negative response to RVP command from BV. H BV LAN cable BV LAN 315-318,011
2753 <BV>( DVR : Read all validation information area ) Received a negative response to DVR command from BV. H BV LAN cable BV LAN 315-318,011
2760 <BV>( CAL : Clear alarm information area ) Received a negative response to CAL command from BV. H BV LAN cable BV LAN 315-318,011
2761 <BV>( CST : Clear statistics information area ) Received a negative response to CST command from BV. H BV LAN cable BV LAN 315-318,011
2762 <BV>( CVP : Clear recognition information area ) Received a negative response to CVP command from BV. H BV LAN cable BV LAN 315-318,011
2764 <BV>( CMG : Clear message information area ) Received a negative response to CMG command from BV. H BV LAN cable BV LAN 315-318,011
2765 <BV>( CVR : Clear validation information area ) Received a negative response to CVR command from BV. H BV LAN cable BV LAN 315-318,011
2770 <BV>( LPR : Load program ) Received a negative response to LPR command from BV. H BV LAN cable BV LAN 315-318,011
2771 <BV>( LEN : End of program loading ) Received a negative response to LEN command from BV. H BV LAN cable BV LAN 315-318,011
2774 <BV>( SPV : Stop validation ) Received a negative response to SPV command from BV. H BV LAN cable BV LAN 315-318,011
2775 <BV>( SLV : Insertion/transit sensor level notification Received a negative response to SLV command from BV. H BV LAN cable BV LAN 004,315-318,011
2780 <BV>( UMG : Undefined message ) Received a negative response to UMG command from BV. H BV LAN cable BV LAN 315-318,011
2800 <BV>Received invalid data from BV Invalid command code in a response received from BV. H BV 315-318
29** <BV>Cannot start validation on BV ( ** : BV AMC Received a negative response to SVR command from BV. H or S BV 001,002,004,304,31
code ) 5-318,011
2901 <BV>Program is not installed. The program is not installed S or H BV FW BV 001,002,004,304,31
Download 5-318,011
2902 <BV>Program is not installed. The program is not installed < Discrimination part > S or H BV FW BV 001,002,004,304,31
Download 5-318,011
2903 <BV>Program is not installed. The program is not installed < Template part > S or H BV FW BV 001,002,004,304,31
Download 5-318,011
2904 <BV>Validation mode specified error The validation mode is specified the test mode on the template for S BV FW SW setting 001,002,004,304,31
real note. Download 5-318,011
2905 <BV>Validation mode specified error The validation mode is specified the real mode on the template for S BV FW SW setting 001,002,004,304,31
test note. Download 5-318,011
2906 <BV>BV system error The FPGA program is not installed H BV 001,002,004,304,31
5-318,011
2907 <BV>BV system error Memory error H or S BV 001,002,004,304,31
5-318,011
2908 <BV>BV system error BV Open error H BV 001,002,004,304,31
5-318,011
2909 <BV>BV system error Memory error H or S BV 001,002,004,304,31
5-318,011
290A <BV>BV system error FAN error H BV 001,002,004,304,31
5-318,011
290B <BV>BV system error Battery error H BV 001,002,004,304,31
5-318,011
290C <BV>BV system error non calibration H BV 001,002,004,304,31
5-318,011
290D <BV>BV system error hardware configration error H BV 001,002,004,304,31
5-318,011
290E <BV>BV system error Memory error H or S BV 001,002,004,304,31
5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 8 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
290F <BV>BV system error Power error H BV 001,002,004,304,31
5-318,011
2912 <BV>BV system error Flash-ROM erase error H BV 001,002,004,304,31
5-318,011
2913 <BV>BV system error Flash-ROM write error H BV 001,002,004,304,31
5-318,011
2914 <BV>BV system error The command is received during validating H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2915 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2916 <BV>BV system error SUB-CPU communication error H BV 001,002,004,304,31
5-318,011
2917 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2918 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2919 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
291A <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
291B <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
291C <BV>BV system error ARM-DSP communication error H BV 001,002,004,304,31
5-318,011
291E <BV>BV system error DSP error H BV 001,002,004,304,31
5-318,011
291F <BV>BV system error mecha number error H BV 001,002,004,304,31
5-318,011
2920 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2921 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2922 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2923 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2924 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2925 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2926 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2927 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2928 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 9 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
2929 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
292A <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
292B <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
292C <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
292D <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
292E <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
292F <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2930 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2931 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2932 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2933 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2934 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2935 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2936 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2937 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2938 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
2939 <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
293A <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
293B <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
293C <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
293D <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
293E <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011
293F <BV>BV system error communication error(To magnetic sensor / analog board) H BV 001,002,004,304,31
5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 10 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
2941 <BV>Notes remaining There is a medium on image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2942 <BV>Notes remaining There is a medium on image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2943 <BV>Notes remaining There is a medium on image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2944 <BV>Notes remaining There is a medium on image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2945 <BV>Notes remaining There is a medium on BV-IN/OUT sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2946 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2947 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2948 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2949 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
294A <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
294B <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
294C <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
294D <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
294E <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
294F <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2951 <BV>Calibration error Image sensor error H Sensor cleaning BV 001,002,004,304,31
5-318,011
2952 <BV>Calibration error Magnetic sensor error H Sensor cleaning BV 001,002,004,304,31
5-318,011
2953 <BV>Calibration error UV sensor error H Sensor cleaning BV 001,002,004,304,31
5-318,011
2954 <BV>Calibration error Thickness sensor error H Sensor cleaning BV 001,002,004,304,31
5-318,011
2957 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2958 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
2959 <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011
295A <BV>Calibration error Calibration error of image sensor. H Sensor cleaning BV 001,002,004,304,31
5-318,011

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 11 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
295C <BV>Communication error Download data error H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2960 <BV>Communication error Receive command error (From BRU) H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2961 <BV>Communication error Receive data error (From BRU) H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2962 <BV>Communication error Receive SUM error (From BRU) H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2963 <BV>Communication error Receive data length error (From BRU) H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2964 <BV>Communication error The paratemer of cheque image read is invalid. H or C BV LAN cable or BV LAN 001,002,004,304,31
LPCB 5-318,011
2966 <BV>BV system error Internal processing is error. H BV 001,002,004,304,31
5-318,011
2967 <BV>BV system error Internal processing is error. H BV 001,002,004,304,31
5-318,011
2968 <BV>BV system error Internal processing is error. H BV 001,002,004,304,31
5-318,011
2969 <BV>BV system error Internal processing is error. H BV 001,002,004,304,31
5-318,011
296A <BV>BV system error The setting of the handling denomination is an error. S or H BV FW BV 001,002,004,304,31
Download 5-318,011
2B00 <BV>Received invalid validation data from BV Validation data from BV showed invalid denomination during H or C BV LAN cable BV LAN 013,315-318,011
note validation.
2B01 <BV>Parity error of validation data from BV. Parity error in validation data from BV during note validation. H or C BV LAN cable BV LAN 315-318,011
2B10 <BV>BV cover doesn't shut. BV cover open detected in JA,MR,MJ commands. H or C BV 004,317-318,011
2B20 <BV>The medium remains to BV. Note remain detected inside BV in JA,MR,MJ commands. H or C BV 001,002,317-318,
011
2C00 <BV>Number of notes according to denomination The number of notes according to denomination stored in storages S or H Reset with SW BV 001,002,011
is not suit between primary and secondary payment was not same as that pooled in Escrow when Not recognized note
was not detected during DP command.
The number of notes according to denomination stored in storages
was more than that pooled in Escrow when Not recognized notes
were detected during DP command.
3*** relate with Command Error More notes were returned to the original cassette than stored in
3000 <Operation>RAS-number is not available Invalid value input in RAS mode. O Operation 015
3001 <Cassettes>Cassette for performing RAS is not ready. The number of setting cassette was not 2 or 4 cassettes at the RAS S SW setting 005,007
command.
It was not the denomination same per 2 cassettes at the RAS
command.
Both were empty per 2 cassettes at the RAS command.
The type of setting cassette was Deposit cassette at the RAS

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 12 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
3100 <Cassettes>There isn't cassette which can be sent out. Recycle cassette supporting the requested denominaion was not S or C SW setting CS1-4 005,013
mounted into the module at dispensing.
Recycle cassette supporting the requested denominaion was Mix
denomination cassette at dispensing.
Recycle cassette supporting the requested denominaion was
Suspect cassette at dispensing.
Recycle cassette supporting the requested denominaion was
Damaged cassette at dispensing.
Recycle cassette supporting the requested denominaion was
Generation mix cassette at dispensing.
Recycle cassette supporting the requested denominaion was
Publication mix cassette at dispensing.
3101 <Cassettes>Number of notes is not reach to request. Number of dispensed notes did not reach the number of notes S SW setting 005,007
requested.
3102 <Cassettes>Payment number of notes over The sum of the requested notes and the notes stored in Escrow S SW setting 013
exceeded 200 before dispensing operation.
3200 <Cassettes>Target cassette is not a recycling type. Deposit cassette was specified as a Target cassette at S SW setting 005
reconciliation.

3201 <Cassettes>Temporary cassette is not a recycling type. Deposit cassette was specified as a Temporary cassette at S SW setting 005
reconciliation.
3210 <Cassettes>Temporary cassette cannot be specified to Temporary cassette was specified as a Target cassette at S SW setting 005
be a target cassette. reconciliation.
3300 <Cassettes>There is no Temporary cassette. No temporary cassette was specified at reconciliation. S SW setting 005
3310 <Separator>There is no note in Separator. Separator was empty in RAS-C1,C2,C3 operation. O Operation 015
3400 <Cassettes>The medium remains to temporary cassette. Notes remained in Temporary cassette at reconciliation. S SW setting 005
3411 <Pre-Acceptor>The medium which should be extracted Notes detected in Pre-acceptor after shutter close operation H PA SHT 001,002
remains to pre-acceptor. completed at TO/AP command.
3412 <Cassette Transport>The medium remains to knot URHS sensor remained blocked when clearing jam error after O or H Operation CAS URHS 001,002
portion between upper unit and lower unit (rear). pulling out the lower unit and returning it to the mounting position
again for jam recovery.
3413 <Transport before BV>The medium remains to knot LFHS sensor remained blocked when clearing jam error after O or H Operation BV LFHS 001,002
portion between upper unit and lower unit (front). pulling out the lower unit and returning it to the mounting position
again for jam recovery.
3414 <Cassette Transport>The medium remains to lower Clearing jam error after pulling out the lower unit and returning it O or H Operation LT URHS,LT3S, 001,002
unit. to the mounting position again for jam recovery. LFHS,UFHS

3500 <Separator Transport>Not detect home position of SCDC and SHDC sensors were not cleared within the specified H SEP SCDC,SHDC SEDM 101-108,301-307
deskew lever time when moved deskew roller to home position at MR, MJ
commands.

3501 <Separator Transport>Not detect right position of SCDC sensor was not blocked or SHDC sensor was not cleared H SEP SCDC,SHDC SEDM 101-108,301-307
deskew lever within the specified time when moved deskew roller to right.
3502 <Separator Transport>Not detect left position of SCDC sensor was not cleared or SHDC sensor was not blocked H SEP SCDC,SHDC SEDM 101-108,301-307
deskew lever within the specified time when moved deskew roller to left.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 13 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
3503 <Separator Transport>The step-out of deskew motorWhen the deskew roller was moved from right or left position, the H SEP SCDC,SHDC SEDM 101-108,301-307
(SEDM) was detected. home position (SCDC and SHDC sensors were cleared) was
detected faster than the specified time.
3510 <Separator Transport>Two or more sensor change was SCDC/SHDC sensors were following impossible state. H SEP SCDC,SHDC 001,002,301-
detected simultaneously.(SCDC/SHDC) SCDC sensor : blocked & SHDC sensor : blocked 307,311,312
3C00 <Bill Validate>Number of notes is not suit between The number of notes stored in storages was not same as that J or H SEP ESC 110,111,210-
primary and secondary payment pooled in Escrow when Not recognized note was not detected 212,301,307,011
during DP command.
The number of notes stored in storages was more than that pooled
in Escrow when Not recognized notes were detected during DP
command.
3C01 <Escrow Transport>The half-note was detected. More notes
During notewere returned
transport to the original
to Escrow cassette than
at WC command, onestored
of in H ESC EDLS,EDRS 203-206,301-306
EDLS/EDRS sensors was blocked but the other was not.
3C02 <GBNA/GBRU>Note disappear in GBNA/GBRU Note disappeared, though it doesn't open GBNA/GBRU, and it J or O Operation 001,010,301-307
doesn't store it.
3F00 <Operation>Authentication time out There was not physical intervention for authetication though the O Operation 016
specified time was passed.
3F01 <Operation>Authentication abort The physical intervention processing for authetication was aborted O Operation 016
by the host.
3F02 <Host interface>Impossible check download for Whether download was possible was not able to be checked S or H LPCB 013
authentication because the data length of the first block was less than 20 bytes.
3F03 <Operation>Authetication not support firmware The old firmware to which the authentication was not supported O or H Operation LPCB 017,307
download was downloaded.
3F04 <Host interface>Authentication invalid mode The specified mode in AF parameter cannot be executed. S or H LPCB 013
4*** relate with Unit Set & Full
4001 <Upper Unit>Upper unit was not set. Upper unit was not set at the start of a command. H or O ESC and UT UPCN UULC 004,301-307
4002 <Lower Unit>Lower unit was not set. Lower unit was not set at the start of a command. H or O LT and UT LB or UB ULPC 004,009,301-307
or Cradle
4003 <Lower Transport> Lower transport was not set. Lower transport was not set at the start of a command. H or O LT LB BLLC 004,301-307
4004 <Reject bin>Reject area was not set. Reject bin was not set at the start of a command. H or O RJ Bin UT URLC 004,005,301-307
4005 <Cassette 1>Cassette 1 was not set. Cassette 1 was not set at the start of a command. H or O CAS1 LB 005,006,301-
307,309

4006 <Cassette 2>Cassette 2 was not set. Cassette 2 was not set at the start of a command. H or O CAS2 LB 005,006,301-
307,309

4007 <Cassette 3>Cassette 3 was not set. Cassette 3 was not set at the start of a command. H or O CAS3 LB 005,006,301-
307,309

4008 <Cassette 4>Cassette 4 was not set. Cassette 4 was not set at the start of a command. H or O CAS4 LB 005,006,301-
307,309

4009 <Transport before BV>Transport before BV was not Transport in front of BV was not set at the start of a command. H or O BV URCN SBLC 004,301-307
set.
400A <Transport under Reject bin>Transport under Reject Transport under Reject bin was not set at the start of a command. H or O UT UGLC 004,301-307
bin was not set.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 14 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
400B <Top Transport>Top transport was not set. Top transport was not set at the start of a command. H or O ESC ETLC 004,301-307
400F <Host Interface>Immediately after a power supply ON Interlock was not set at the start of a command. H or O Interlock SW LB or PSU Interlock SW 003
or a power supply OFF
4300 <Counterfeit area>Counterfeit area fills with notes. Counterfeit area was full before note transport. H or O RJ Bin UT 007,010,225,227,30
1-307
4301 <Reject area>Reject area fills with notes. Reject area was full before note transport. H or O RJ Bin UT 007,010,225,227,30
1-307
4302 <Captured area>Captured area fills with notes. Captured area was full before note transport. H or O RJ Bin UT 007,010,225,227,30
1-307
4303 <Escrow>Escrow fills with notes. Escrow was full before note transport. H or O ESC 006,010,113,206,22
Escrow FULL detected during note transport. 6
4304 <Reservoir>Reservoir fills with notes. Reservoir was full before note transport. H or O ESC 006,010,114,115,22
Reservoir FULL detected during note transport. 6
4305 <Cassette 1>Cassette 1 fills with notes. Cassette 1 was full before note transport. H or O CAS1 007,301-307,309
Cassette 1 FULL detected during note transport.
4306 <Cassette 2>Cassette 2 fills with notes. Cassette 2 was full before note transport. H or O CAS2 007,301-307,309
Cassette 2 FULL detected during note transport.
4307 <Cassette 3>Cassette 3 fills with notes. Cassette 3 was full before note transport. H or O CAS3 007,301-307,309
Cassette 3 FULL detected during note transport.
4308 <Cassette 4>Cassette 4 fills with notes. Cassette 4 was full before note transport. H or O CAS4 007,301-307,309
Cassette 4 FULL detected during note transport.
4501 <Host Interface>Have different unit types.(BNA or PP/UC/BC/WC/SK commands were issued to BNA unit. S SW setting 006,301-306,309
BRU)
5*** relate with FRU memory Error
5001 <FRU Memory>Transmission failed The transmission is not completed in the regulation time. H or S LPCB 307,013
5002 <FRU Memory>Response timeout After the command had been sent, the response did not return in H or C FPCB SPCB or LPCB TERM 301,307
the regulation time.
5003 <FRU Memory>Response length error The data length invalid when receiving a response. H or C FPCB SPCB or LPCB TERM 301,307
5004 <FRU Memory>Response sum error The sum of a response received did not match. H or C FPCB SPCB or LPCB TERM 301,307
5005 <FRU Memory>Reponse illegal function code The function code of a response received is illegal code. H or C FPCB SPCB or LPCB TERM 301,307
5006 <FRU Memory>Sending data from BRU and Receiving The command is not supported on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
data from FRU memory controller is discode The communication error is detected on FRU memory controller.
Mismatch between data send command and data receive command
when receiving a response from FRU memory controller.
5100 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5101 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5110 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5111 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5112 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5113 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5114 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5115 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5120 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5121 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5122 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
512F <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 15 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
5130 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5131 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5132 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5133 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5134 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5135 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
513F <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5140 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5141 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5142 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5143 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5144 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5145 <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
514F <FRU Memory>FRU memory controller error The error category of a response received was invalid value. H or S FPCB SPCB or LPCB 307,013
5200 <FRU memory>No error code There is no error code though the error was reported. H or S FPCB SPCB or LPCB 307,013
5201 <Pre-acceptor>No memory The memory was not connected. H or C PAC FPCB or SPCB MEMCN 301,307
5210 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5211 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5212 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5213 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5214 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5215 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5220 <Pre-acceptor>Memory read error The error was detected by reading from the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5221 <Pre-acceptor>Memory read error The error was detected by reading from the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5222 <Pre-acceptor>Memory read error The error was detected by reading from the memory. H or C PAC FPCB or SPCB MEMCN 301,307
522F <Pre-acceptor>Memory read error The error was detected by reading from the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5230 <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5231 <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5232 <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5233 <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5234 <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5235 <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
523F <Pre-acceptor>Memory write error The error was detected by writting in the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5240 <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5241 <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5242 <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5243 <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5244 <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5245 <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
524F <Pre-acceptor>Memory erase error The error was detected by erasing the data of the memory. H or C PAC FPCB or SPCB MEMCN 301,307
5300 <FRU memory>No error code There is no error code though the error was reported. H or S FPCB SPCB or LPCB 307,013
5301 <Separator>No memory The memory was not connected. H or C SEP FPCB or SPCB MEMCN 301,307
5310 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5311 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5312 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5313 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 16 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
5314 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5315 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5320 <Separator>Memory read error The error was detected by reading from the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5321 <Separator>Memory read error The error was detected by reading from the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5322 <Separator>Memory read error The error was detected by reading from the memory. H or C SEP FPCB or SPCB MEMCN 301,307
532F <Separator>Memory read error The error was detected by reading from the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5330 <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5331 <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5332 <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5333 <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5334 <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5335 <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
533F <Separator>Memory write error The error was detected by writting in the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5340 <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5341 <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5342 <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5343 <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5344 <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5345 <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
534F <Separator>Memory erase error The error was detected by erasing the data of the memory. H or C SEP FPCB or SPCB MEMCN 301,307
5400 <FRU memory>No error code There is no error code though the error was reported. H or S FPCB SPCB or LPCB 307,013
5401 <Escrow>No memory The memory was not connected. H or C ESC FPCB or SPCB MEMCN 301,307
5410 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5411 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5412 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5413 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5414 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5415 <FRU memory>Communication error The communication error is detected on FRU memory controller. H or C FPCB SPCB or LPCB TERM 301,307
5420 <Escrow>Memory read error The error was detected by reading from the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5421 <Escrow>Memory read error The error was detected by reading from the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5422 <Escrow>Memory read error The error was detected by reading from the memory. H or C ESC FPCB or SPCB MEMCN 301,307
542F <Escrow>Memory read error The error was detected by reading from the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5430 <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5431 <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5432 <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5433 <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5434 <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5435 <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
543F <Escrow>Memory write error The error was detected by writting in the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5440 <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5441 <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5442 <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5443 <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5444 <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307
5445 <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307
544F <Escrow>Memory erase error The error was detected by erasing the data of the memory. H or C ESC FPCB or SPCB MEMCN 301,307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 17 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6*** Mechanical error at Pre-
acceptor,Separator,Shutter
6100 <Carrier>Carrier doesn't move forward. PCEC sensor was not blocked within the specified time when J or H ESC PAC or SEP or SE3 or SE7 ECHC/ECPC ESCM 004,101,102,103,10
Carrier moved forward. SPCB /ECCC/PCE 4,106,107,108,110,1
ECPC sensor was not cleared within the specified time when C 11,210,211,212,213,
Carrier moved forward. 301-307,312
ECCC sensor was not cleared within the specified time when
Carrier moved forward.
6101 <Carrier>Carrier doesn't move backward. ECHC sensor was not blocked within the specified time when J or H ESC PAC or SEP or SE3 or SE7 ECHC/ECPC ESCM 101,102,103,104,10
Carrier moved backward. SPCB /ECCC/PCE 6,107,108,110,111,2
ECCC sensor was not cleared within the specified time when C 10,211,212,213,301-
Carrier moved backward. 307,312
6102 <Carrier>Notes under the Carrier. When Carrier moved backward, ECCC sensor was not cleared and J ESC PAC or SEP or SE3 ECCC/ECHC 101,102,103,104,21
ECHC sensor was blocked. SPCB 0,211,213,301-
307,312

6103 <Carrier>Carrier drags notes on Bunch transport. When Carrier moved backward, ECCC sensor was blocked and J ESC PAC or SEP SE3 ECCC/EELS/ 101,102,103,104,21
EELS sensor or EERS sensor was blocked. EERS 0,211,213,301-
307,312

6120 <Pre-Acceptor>Tray doesn't move forward. PDPC sensor was not blocked within the specified time when Tray J or H PAC SE7 PDPC/PRPC/ PATM 001,002,010,101-
moved forward. PTPC 108,201,203,216,21
Step-out was detected at PTPC sensor before 8,301-307
PS1S/PS2S/PS3S/PS4S sensors were blocked when Tray was
moving forward.
Step-out was detected at PTPC sensor before PDPC sensor was
blocked when Tray was moving forward.
Step-out was detected at PTPC sensor when Tray was moving
forward by a specified number of steps.

6121 <Pre-Acceptor>Tray doesn't move backward. PLPC sensor was not blocked within the specified time when Tray J or H PAC SEP SE7 PDPC/PRPC/ PATM 001,002,010,101-
moved backward. PTPC 108,201,203,216,21
PRPC sensor was not blocked within the specified time when Tray 8,301-307
moved backward.
Step-out was detected at PTPC sensor before PRPC sensor was
detected when Tray was moving backward.
Step-out was detected at PTPC sensor before PLPC sensor was
detected when Tray was moving backward.
Step-out was detected at PTPC sensor when Tray was moving
backward by a specified number of steps.
6130 <Pre-Acceptor>Belt doesn't move forward. Step-out was detected at PBPC sensor when Belt was rotating H or J PAC Cable SE7 PBPC PABM 001,002,010,101-
forward. 108,201,202,205,21
4-216,220,301-307
6131 <Pre-Acceptor>Belt doesn't move backward. Step-out was detected at PBPC sensor when Belt was rotating H or J PAC Cable SE7 PBPC PABM 001,002,010,101-
backward. 108,2001,202,205,2
14-216,221,301-307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 18 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6140 <Pre-Acceptor>Clamp doesn't move downward. PTHC sensor was not blocked and POLC sensor was not cleared J or H PAC SEP SE7 PTHC/POLC PACM 001,002,010,101-
when Clamp moved down enough steps. 109,214-
216,220,221,301-
307

6141 <Pre-Acceptor>Clamp doesn't move upward. PTHC sensor was not cleared within the specified time when J or H PAC SEP SE7 PTHC/POLC PACM 001,002,010,101-
Clamp moved up. 109,214-
216,220,221,301-
307

6150 <Pre-Acceptor>Pre-Acceptor Connector doesn't Pre-acceptor connector removal detected when requesting Pre- S or C PAC and Cable FW version PA1 301,302,307
connect. Acceptor to move. or UPCB
6151 <Pre-Acceptor>Pre-Acceptor type doesn't right. Invalid Pre-Acceptor type signal detected when requesting Pre- S or C PAC and Cable FW version PA1 301,302,307
Acceptor to move. or UPCB
6180 <Separator>Pusher doesn't move downward. SPPC sensor was not cleared within the specified time when J or H SEP Cable or PAC SE5 SPPC/SPCC/ SEPM/PDM 001,002,101-
Separator Pusher moved down. PDAC G 108,111,210-
SPCC sensor was not blocked within the specified time when 212,221,301-307
Separator Pusher moved down.
6181 <Separator>Pusher doesn't move upward. SPUC sensor was not blocked within the specified time when J or H SEP Cable or PAC SE5 SPUC/SPBC SEPM 001,002,101-
Separator Pusher moved up. 108,111,210-
SPBC sensor was not blocked within the specified time when 212,221,301-307
Separator Pusher moved up.
6190 <Separator>Stage doesn't move downward. SSLC sensor was not blocked within the specified time when J or H SEP SE5 SSLC SESM 001,002,101-
Separator Stage moved down. 108,111,210-
212,221,301-307
6191 <Separator>Stage doesn't move upward. SSUC sensor was not blocked within the specified time when J or H SEP SE5 SSUC SESM 001,002,101-
Separator Stage moved up. 108,111,210-
212,221,301-307
61A0 <Shutter>Shutter doesn't open after several retry. Shutter Open sensor was not blocked within the specified time H SHT PAC or cable SHT Shutter Open Shutter motor 001,002,004,008,10
when Shutter opened. 9,116,301-307
61A1 <Shutter>Shutter doesn't close after several retry. Shutter Close sensor was not blocked within the specified time H SHT PAC or cable SHT Shutter Close Shutter motor 001,002,004,008,10
when Shutter closed. 9,116,301-307
61B1 <Shutter>Shutter doesn't close. Shutter was not closed at the start of SK command. H SHT PAC or cable SHT Shutter 001,002,004,008,10
Open/Shutter 9,116,301-307
Close
6210 <Carrier>Two or more sensor change was detected ECHC/ECCC/ECPC/PCEC sensors were following impossible H or J ESC PAC or SEP ES3 ECHC/ECPC 001,002,301-
simultaneously.(ECHC/ECCC/ECPC/PCEC) state at the start of mechanical operating. /ECCC/PCE 307,311,312
ECHC sensor : blocked & ECCC sensor : cleared & ECPC sensor : C
cleared & PCEC sensor : blocked
6211 <Carrier>Two or more sensor change was detected ECHC/ECCC/ECPC sensors were following impossible state at H or J ESC SEP or PAC ES3 ECHC/ECCC 001,002,301-
simultaneously.(ECHC/ECCC/ECPC) the start of mechanical operating. /ECPC 307,311
ECHC sensor : blocked & ECCC sensor : cleared & ECPC sensor :
cleared

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 19 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6212 <Carrier>Two or more sensor change was detected ECHC/ECCC/PCEC sensors were following impossible state at H or J ESC PAC or SEP ES3 ECHC/ECCC 001,002,301-
simultaneously.(ECHC/ECCC/PCEC) the start of mechanical operating. /PCEC 307,311,312
ECHC sensor : blocked & ECCC sensor : cleared & PCEC sensor :
blocked
6213 <Carrier>Two or more sensor change was detected ECHC/ECCC sensors were following impossible state at the start H or J ESC SEP or PAC ES3 ECHC/ECCC 001,002,301-
simultaneously.(ECHC/ECCC) of mechanical operating. 307,311
ECHC sensor : blocked & ECCC sensor : cleared
6214 <Carrier>Two or more sensor change was detected ECHC/ECPC/PCEC sensors were following impossible state at H or J ESC PAC or SEP ES3 ECHC/ECPC 001,002,301-
simultaneously.(ECHC/ECPC/PCEC) the start of mechanical operating. /PCEC 307,311,312
ECHC sensor : blocked & ECPC sensor : cleared & PCEC sensor :
blocked
6215 <Carrier>Two or more sensor change was detected ECHC/ECPC sensors were following impossible state at the start H or J ESC SEP or PAC ES3 ECHC/ECPC 001,002,301-
simultaneously.(ECHC/ECPC) of mechanical operating. 307,311
ECHC sensor : blocked & ECPC sensor : cleared
6216 <Carrier>Two or more sensor change was detected ECCC/ECPC/PCEC sensors were following impossible state at H or J ESC PAC or SEP ES3 ECCC/ECPC 001,002,301-
simultaneously.(ECCC/ECPC/PCEC) the start of mechanical operating. /PCEC 307,311,312
ECCC sensor : cleared & ECPC sensor : cleared & PCEC sensor :
blocked
6217 <Carrier>Two or more sensor change was detected ECCC/ECPC sensors were following impossible state at the start H or J ESC SEP or PAC ES3 ECCC/ECPC 001,002,301-
simultaneously.(ECCC/ECPC) of mechanical operating. 307,311
ECCC sensor : cleared & ECPC sensor : cleared
6218 <Carrier>Two or more sensor change was detected ECCC/PCEC sensors were following impossible state at the start H or J ESC SEP or PAC ES3 ECCC/PCEC 001,002,301-
simultaneously.(ECCC/PCEC) of mechanical operating. 307,311,312
ECCC sensor : cleared & PCEC sensor : blocked
6219 <Carrier>Two or more sensor change was detected ECPC/PCEC sensors were following impossible state at the start H or J ESC SEP or PAC ES3 ECPC/PCEC 001,002,301-
simultaneously.(ECPC/PCEC) of mechanical operating. 307,311,312
ECPC sensor : cleared & PCEC sensor : blocked
6220 <Pre-Acceptor>Two or more sensor change was PDPC/PLPC/PRPC sensors were following impossible state at the H or J PAC SE7 or PDPC/PLPC/ 001,002,301-
detected simultaneously.(PDPC/PLPC/PRPC) start of mechanical operating. RV2PH PRPC 307,311
PDPC sensor : blocked & PLPC sensor : blocked & PRPC sensor :
blocked
6221 <Pre-Acceptor>Two or more sensor change was PDPC/PLPC sensors were following impossible state at the start H or J PAC SE7 or PDPC/PLPC 001,002,301-
detected simultaneously.(PDPC/PLPC) of mechanical operating. RV2PH 307,311
PDPC sensor : blocked & PLPC sensor : blocked
6222 <Pre-Acceptor>Two or more sensor change was PDPC/PRPC sensors were following impossible state at the start H or J PAC SE7 or PDPC/PRPC 001,002,301-
detected simultaneously.(PDPC/PRPC) of mechanical operating. RV2PH or 307,311
PDPC sensor : blocked & PRPC sensor : blocked URCN
6223 <Pre-Acceptor>Two or more sensor change was PLPC/PRPC sensors were following impossible state at the start of H or J PAC SE7 or PLPC/PRPC 001,002,301-
detected simultaneously.(PLPC/PRPC) mechanical operating. RV2PH 307,311
PLPC sensor : blocked & PRPC sensor : blocked
6281 <Separator>Two or more sensor change was detected SPUC/SPBC sensors were following impossible state at the start H or J SEP SE5 SPUC/SPBC 001,002,301-
simultaneously.(SPUC/SPBC) of mechanical operating. 307,311
SPUC sensor : blocked & SPBC sensor : blocked
6282 <Separator>Two or more sensor change was detected SPUC/SPCC sensors were following impossible state at the start H or J SEP SE5 SPUC/SPCC 001,002,301-
simultaneously.(SPUC/SPCC) of mechanical operating. 307,311
SPUC sensor : blocked & SPCC sensor : blocked

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 20 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6290 <Separator>Two or more sensor change was detected SSUC/SSLC sensors were following impossible state at the start of H or J SEP SE5 SSUC/SSLC 001,002,301-
simultaneously.(SSUC/SSLC) mechanical operating. 307,311
SSUC sensor : blocked & SSLC sensor : blocked
62A0 <Separator>Comb doesn't move thrust direction. When SRMG switched on, SFOC sensor was not blocked after J or H SEP ESC SE5 or SE6 SFOC SRMG 001,002,101,102,10
waiting the specified time. 7-109,112,301-307
62A1 <Separator>Comb doesn't move escape direction. When SRMG switched off, SFIC sensor was not blocked after J or H SEP ESC SE5 or SE6 SFIC SRMG 001,002,101,102,10
waiting the specified time. 7-109,112,301-307
62A2 <Separator>Two or more sensor change was detected SFOC/SFIC sensors were following impossible state at the start of H or J SEP SE5 SFOC/SFIC 001,002,301-
simultaneously.(SFOC/SFIC) mechanical operating. 307,311
SFOC sensor : blocked & SFIC sensor : blocked
62B0 <Shutter>Shutter module break away or Illegal Shutter Open/Shutter Close sensors were following impossible H SHT SHT Shutter 001,002,116,219,30
detected sensor. state at the start of mechanical operating. Open/Shutter 1-307,311
Shutter Open sensor : blocked & Shutter Close sensor : blocked Close
6600 <Pre-Acceptor>Media remains at Pre-acceptor. Media remaining data of Pre-acceptor memorized by software had J or H PAC PS1S/PS2S/P 001,002,010,101-
been set at the start of a command. S3S/PS4S/PT 108,201,202,205,20
PS1S/PS2S/PS3S/PS4S/PTCS/PASS/PDSS sensors were blocked CS/PASS/PD 6,217,218,219,220,2
in the media remaining check processing. SS 21,301-307
6601 <Separator>Media remains at Separator. Media remaining data of Separator memorized by software had J or H SEP SE5 SSEC/SPCC SEFM 001,002,010,101-
been set at the start of a command. 108,111,112,203,20
Note was detected by SSEC sensor in Separator during MR 5,206,210-212,301-
command processing. 307
Note was detected by SSEC sensor in Separator after note
transport to Pre-acceptor.
6603 <Pre-Acceptor>Belt slipped and a medium has not PDSS sensor did not become clear within the specified time when J or H PAC SEP (Stage) or PA3 or SE7 PBPC/PDSS PABM 002,010,101,103,10
been moved. notes were transported to Pre-acceptor using Belt. ESC (Carrier) or PA1 4,105,106,201,202,2
05,206,214-217,220,
221,301-307
6604 <Pre-Acceptor>Jam, note can not be transported in Pre- PTCS/PS1S/PS2S/PS3S/PS4S sensors were blocked before PDSS J or H PAC PA3 or SE7 PBPC/PDSS/ PABM,PAM 002,010,101,103,10
acceptor. sensor become clear when notes were transported in Pre-acceptor or PA1 PS1S/PS2S/P G 4,105,106,201,202,2
using Belt. S3S/PS4S/PT 05,206,214-217,220,
CS 221,301-307
6605 <Pre-Acceptor>Media remains in Pre-acceptor at no The medium was detected with Pre-acceptor at the mode that did J or H PAC PA3 PDSS/PASS/ 002,010,101,103,10
using Hook. not use Hook. PTCS/PS1S/ 4,105,106,201,202,2
PS2S/PS3S/P 05,206,214-217,220,
S4S 221,301-307
6606 <Separator>Media detected at Pre-acceptor by the After the note had been fed from Separator, the medium was J or H SEP PAC SE5 or PA3 SSEC/SPCC/ 001,002,010,101-
additional check. detected at Pre-acceptor by the additional media remaining check PDSS/PASS/ 108,111,112,201,20
operation. PTCS/PS1S/ 2,203,205,206,210-
- In DP command, when the number of sheets of the stored note PS2S/PS3S/P 212,301-307
decreases.(When the error doesn't occur) S4S
- In RJ & MJ command, when the note was fed.(When the error
doesn't occur)

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 21 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6610 <Pre-Acceptor>Media detection at Pre-acceptor after PDSS sensor has blocked though it pushed with Tray to move the J or H PAC PA3 PDSS 001,002,010,101-
pussing the media to Separator medium to Separator. 108,201,202,205,20
6,218,219,221,301-
307

6611 <Pre-Acceptor>Media detection outside Tray after PDSS sensor was blocked after moving the media to Pre-Acceptor J or H PAC PA3 PDSS 001,002,010,101-
moving the media to Pre-acceptor and moving Tray forward a little. 108,201,202,205,20
6,218,219,221,301-
307

6612 <Pre-Acceptor>Media detection outside Separator During Pre-acceptor preparation for moving the media from J or H PAC PA3 PDSS 001,002,010,101-
during Pre-acceptor preparation Seprator to Pre-acceptor, PDSS sensor was blocked after moving 108,201,202,205,20
Tray forward a little because D-Stopper did not escape. 6,218,219,221,301-
307

6613 <Pre-Acceptor>Belt slipped and a medium has not PDSS sensor did not become clear within the specified time when J or H PAC SEP (Stage) or PA3 or SE7 PDSS PABM 001,002,010,101-
been moved to Pre-acceptor. notes were transported to Pre-acceptor using Belt. ESC (Carrier) or PA1 108,201,202,205,20
6,218,219,221,301-
307

6614 <Pre-Acceptor>Belt slipped and a medium has not PDSS sensor did not become clear within the specified time when J or H PAC PA3 or SE7 PDSS PABM 001,002,010,101-
been moved to Separator. notes were transported to Separator using Belt. or PA1 108,201,202,205,20
6,218,219,221,301-
307

6615 <Pre-Acceptor>Media detection outside Separator after PDSS sensor was blocked after moving the media to Separator and J or H PAC PA3 or PA1 PDSS PATM 001,002,010,101-
moving the media to Separator moving Tray forward a little. 108,201,202,205,20
6,218,219,221,301-
307

6616 <Pre-Acceptor>Media detection at the front of Pre- PS1S/PS2S/PS3S/PS4S sensor were blocked when Tray was J or H PAC PA3 PS1S/PS2S/P 001,002,010,101-
acceptor before Tray was moved backward moved backward. S3S/PS4S 108,201,202,205,20
6,218,219,221,301-
307

6617 <Pre-Acceptor>Media detection at the front of Pre- PS1S/PS2S/PS3S/PS4S sensor were blocked when Tray was J or H PAC PA3 PS1S/PS2S/P 001,002,010,101-
acceptor before Tray was moved forward moved forward. S3S/PS4S 108,201,202,205,20
6,218,219,221,301-
307

6618 <Pre-Acceptor>Media detection at the front of Pre- PDPC sensor was not blocked though Tray was moved forward a J or H PAC PA3 or PA1 PS1S/PS2S/P PATM 001,002,010,101-
acceptor, or Tray doesn't move forward little because PS1S/PS2S/PS3S/PS4S sensors had blocked. S3S/PS4S 108,201,202,205,20
6,218,219,221,301-
307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 22 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6619 <Pre-Acceptor>Media detection at the front of Pre- PS1S/PS2S/PS3S/PS4S sensors were blocked after Tray was J or H PAC PA3 PS1S/PS2S/P 001,002,010,101-
acceptor after Tray was moved backward moved to PRPC sensor blocked. S3S/PS4S 108,201,202,205,20
6,218,219,221,301-
307

661A <Pre-Acceptor>Media remains at Pre-acceptor. PHPC sensor was not blocked when Hook was thrusted in the J or H PAC RV2PH or PHPC PAMG 001,002,010,101-
media remaining check processing. PA1 108,201,202,205,20
6,217,218,219,301-
307

661B <Pre-Acceptor>Media remains at Pre-acceptor. PS1S/PS2S/PS3S/PS4S/PTCS sensors were blocked in the media J or H PAC PA3 PS1S/PS2S/P 001,002,010,101-
remaining check processing. S3S/PS4S/PT 108,201,202,205,20
CS 6,218,219,221,301-
307

661C <Pre-Acceptor>Media remains at Pre-acceptor. PS1S/PS2S/PS3S/PS4S/PTCS sensors were blocked after Hook/D- J or H PAC PA3 PS1S/PS2S/P 001,002,010,101-
stopper escape in the media remaining check processing. S3S/PS4S/PT 108,201,202,205,20
CS 6,217,218,219,221,3
01-307
661D <Pre-Acceptor>Media detection at the rear of Pre- PDSS sensor was blocked after moving the media to Separator J or H PAC PA3 or PA1 PDSS PABM 001,002,010,101-
acceptor after moving the media to Separator (PDSS sensor was cleared) and moving Belt backward a little in 108,201,202,205,20
the retry processing. 6,218,219,221,301-
307

661E <Pre-Acceptor>Media detection at the rear of Pre- PDSS sensor was blocked after moving the media to Separator J or H PAC PA3 PDSS 001,002,010,101-
acceptor after moving the media to Separator (PDSS sensor was cleared) and moving Clamp up in the retry 108,201,202,205,20
processing. 6,218,219,221,301-
307

6700 <Pre-Acceptor>Hook doesn't escape at Pre-acceptor. PHPC sensor was not blocked after waiting the specified time J or H PAC RV2PH PHPC PHMG, 001,002,010,101,10
when PHMG solenoid switched off. PDMG 2,107,217,220,221,3
01-307
6701 <Pre-Acceptor>Hook doesn't thrust at Pre-acceptor. PHPC sensor was not cleared after waiting the specified time J or H PAC RV2PH PHPC PHMG 001,002,010,101,10
when PHMG solenoid switched on. 2,107,217,220,221,3
01-307
6702 <Pre-Acceptor>D-stopper doesn't thrust at Pre- PDAC sensor was not blocked after waiting the specified time J or H PAC PDACor PA1 PDAC PDMG 001,002,010,101,10
acceptor. when PDMG solenoid switched on. 2,107,220,221,301-
307

6703 <Pre-Acceptor>D-stopper doesn't escape at Pre- PDAC sensor was not blocked after waiting the specified time J or H PAC PDACor PA1 PDAC PDMG 001,002,010,101,10
acceptor. when PDMG solenoid switched off. 2,107,220,221,301-
307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 23 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6704 <Pre-Acceptor>D-stopper thrust while the note was PDAC sensors were blocked drawing notes J or H PAC PDACor PA1 PDAC PDMG 001,002,010,101,10
moving. 2,107,220,221,301-
307

6710 <Pre-Acceptor>Hook doesn't escape at Pre-acceptor. PHPC sensor was not cleared after waiting the specified time J or H PAC RV2PH PHPC PAMG 001,002,010,101,10
when PAMG solenoid switched off. 2,107,217,301-307
6720 <Pre-Acceptor>Hook doesn't thrust at Pre-acceptor. PHPC sensor was not blocked after waiting the specified time J or H PAC RV2PH PHPC PAMG 001,002,010,101,10
when PAMG solenoid switched on. 2,107,217,301-307
6730 <Pre-Acceptor>D-stopper doesn't thrust at Pre- PDAC sensor was not cleared after waiting the specified time J or H PAC PDACor PA1 PDAC PHMG 001,002,010,101,10
acceptor. when PHMG solenoid switched on. 2,107,221,301-307
6731 <Pre-Acceptor>D-stopper doesn't thrust at Pre- PDAC sensor was not cleared after waiting the specified time J or H PAC PDACor PA1 PDAC PHMG 001,002,010,101,10
acceptor. when PHMG solenoid switched on.(After moving the media to the 2,107,221,301-307
Separator)
6740 <Pre-Acceptor>D-stopper doesn't escape at Pre- PDAC sensor was not blocked after waiting the specified time J or H PAC PDACor PA1 PDAC PHMG 001,002,010,101,10
acceptor. when PHMG solenoid switched off. 2,107,221,301-307
6750 <Pre-Acceptor>D-stopper fell during the Belt was PDAC sensor was cleared during the Belt was rotated to J or H PAC PDACor PA1 PDAC PHMG 001,002,010,101,10
rorated to backward. backward. 2,108,221,301-307
6800 <Separator>Separator doesn't feed backward. SFPC sensor was not cleared within the specified time when J or H SEP SE5 or SE4 SFPC SEFM 002,101-108,301-
SEFM motor rotated back. 307
6900 <Pre-Acceptor>Note remain in Pre-acceptor. PDSS sensor was not cleared after transport notes to Separator J or H PAC SEP PA3 or PA1 PDSS PDMG 010,104,201,202,21
from Pre-acceptor. 4-218,220,221,301-
307
6C00 <Pre-Acceptor>Note disappear from sensor.(PDSS) PDSS sensor was not blocked when Carrier moved until PCEC J or H PAC SEP or PA3 PDSS 001,010,301-307
sensor was blocked. ESC (Carrier)
6C02 <Pre-Acceptor>Note disappear in Pre-acceptor The medium disappeared at the time of moving to the point of Pre- J or H PAC SEP PA3 or SE7 PDPC/PTCS/ 001,010,301-307
acceptor, and Tray detected the PDPC sensor PS1S/PS2S/P
S3S/PS4S
6C11 <Pre-Acceptor>Notes disappeared from Pre-acceptor. Separator was empty when they were transported to Separator J or H PAC SEP PA3 or SE7 SSEC 001,010,301-307
from Pre-accceptor. or SE5 PTCS/PS1S/
PS2S/PS3S/P
S4S
6C21 <Separator>Notes disappeared from Separator. Separator was empty though there was note in Separator. J or H SEP SE5 SSEC 001,010,301-307
6F70 <Pre-Acceptor>Pre-acceptor fails to draw notes. PASS/PTCS/PS1S/PS2S/PS3S/PS4S sensors were blocked after J or H PAC SHT PA3 or SE7 PBPC/PTPC/ PATM,PAB 001,002,010,101-
drawing notes from Pre-acceptor top. or PA1 PASS/PTCS/ M 108,201-
PDSS 203,205,214-
216,218,301-307
6F71 <Pre-Acceptor>Pre-acceptor fails to prepare for PLPC sensor was not blocked when notes were drawn into Pre- J or H PAC RV2PH or PLPC/PRPC PATM,PAB 001,002,010,101-
drawing notes. acceptor until PRPC sensor was blocked. SE7 or PA1 M 108,201-
203,205,214-
216,218,301-307
6F80 <Separator>Separator doesn't feed note. SSRS/SSLS/SSOS sensors were not blocked within the specified J or H SEP SE5 or SE4 SFPC/SSEC/ SEFM 002,010,101-
time when picked up notes from Separator. SPPC/SPCC 108,203-206,301-
307

6F81 <Separator>Separator doesn't confirm empty. The empty was detected when transporting notes from Separator, J or H SEP SE5 or SE4 SFPC/SSEC/ SEFM 101-109,210-
but it was not empty when operating the mechanism after that. SPPC/SPCC 212,301-307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 24 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
6F82 <Separator>Poor rotation of motor.(SEFM) Step-out was detected at SFPC sensor during SEFM motor H SEP SE5 or SE4 SFPC SEFM 002,101-108,301-
rotating. 307

6F83 <Separator>The number of not recognized notes in The number of not recognized notes reached the maximum H BV SEP 001,002,010,011,01
Separator was exceeded. number while notes were transported from Separator. 2,203-
206,302,303,304,30
7,308
6F84 <Separator>The number of damaged notes in Separator The number of damaged notes reached the maximum number H BV SEP 001,002,010,011,01
was exceeded. when notes were transported from Separator. 2,203-
206,302,303,304,30
7,308
6F86 <Separator>The number of counterfeit notes in The number of counterfeit notes reached the maximum number H BV SEP 010,011
Separator was exceeded. when notes were transported from Separator.
6F88 <Separator>The number of suspect note / counterfeit The number of suspect note / counterfeit notes reached the H BV SEP 010,011
notes in Separator was exceeded. maximum number when notes were transported from Separator.
7*** Mechanical error at Escrow & Reservoir
7100 <Reservoir>Reservoir doesn't move downward. ERLC sensor was not blocked within the specified time when J or H ESC ES1 or ES2 ERLC/ERRC ERSM 001,002,010-
Reservoir Stage moved down. 108,111,114,115,20
ERRC sensor was not blocked within the specified time when 5,206,210-213,301-
Reservoir Stage moved down. 307
7101 <Reservoir>Reservoir doesn't move upward. ERRC sensor was not blocked within the specified time when J or H ESC ES1 or ES2 ERRC/ERUC ERSM 001,002,010-
Reservoir Stage moved up. 108,111,114,115,20
ERUC sensor was not blocked within the specified time when 5,206,210-213,301-
Reservoir Stage moved up. 307
7180 <Escrow>Escrow doesn't move downward. EEUC sensor was not blocked within the specified time when J or H ESC ES3 or ES2 EEUC/ETRS/ EESM 001,002,010-
Escrow Stage moved down. ETLS 108,111,113,205,20
ETRS/ETLS sensors were not blocked within the specified time 6,210-213,301-307
when Escrow Stage moved down.
ETRS/ETLS sensors were not cleared within the specified time
when Escrow Stage moved down.
7181 <Escrow>Escrow doesn't move upward. EERC sensor was not blocked within the specified time when J or H ESC ES1 or ES2 EERC EESM 001,002,010-
Escrow Stage moved up. 108,111,113,205,20
6,210-213,301-307
7200 <Reservoir>Unjust position Escrow. ERUC sensor was already blocked when trying to move Reservoir H ESC ES1 ERUC/ERRC 210-212,301-307
Stage to ERRC sensor.
7201 <Reservoir>Illegal detected sensor. ERLC sensor was blocked when Reservoir Stage moved down to H ESC ES1 ERLC/ERRC 301-307
ERRC sensor.
7202 <Reservoir>Two or more sensor change was detected ERUC/ERRC/ERLC sensors were following impossible state at H or J ESC ES1 ERUC/ERRC 301-307,311
simultaneously.(ERUC/ERRC/ERLC) the start of mechanical operating. /ERLC
ERUC sensor : blocked & ERRC sensor : blocked & ERLC sensor
: blocked
7203 <Reservoir>Two or more sensor change was detected ERUC/ERRC sensors were following impossible state at the start H or J ESC ES1 ERUC/ERRC 301-307,311
simultaneously.(ERUC/ERRC) of mechanical operating.
ERUC sensor : blocked & ERRC sensor : blocked

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 25 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
7204 <Reservoir>Two or more sensor change was detected ERUC/ERLC sensors were following impossible state at the start H or J ESC ES1 ERUC/ERLC 301-307,311
simultaneously.(ERUC/ERLC) of mechanical operating.
ERUC sensor : blocked & ERLC sensor : blocked
7205 <Reservoir>Two or more sensor change was detected ERRC/ERLC sensors were following impossible state at the start H or J ESC ES1 ERRC/ERLC 301-307,311
simultaneously.(ERRC/ERLC) of mechanical operating.
ERRC sensor : blocked & ERLC sensor : blocked
7280 <Escrow>Illegal detected sensor. EERC sensor was blocked when Escrow Stage moved up to EEUC H or J ESC ES3 EERC/EEUC 301-307
sensor.
7281 <Escrow>Two or more sensor change was detected EERC/EEUC/EELC sensors were following impossible state at the H or J ESC ES3 EERC/EEUC 301-307,311
simultaneously.(EERC/EEUC/EELC) start of mechanical operating. /EELC
EERC sensor : blocked & EEUC sensor : blocked & EELC sensor
: blocked
7282 <Escrow>Two or more sensor change was detected EERC/EEUC sensors were following impossible state at the start H or J ESC ES3 EERC/EEUC 301-307,311
simultaneously.(EERC/EEUC) of mechanical operating.
EERC sensor : blocked & EEUC sensor : blocked
7283 <Escrow>Two or more sensor change was detected EERC/EELC sensors were following impossible state at the start H or J ESC ES3 EERC/EELC 301-307,311
simultaneously.(EERC/EELC) of mechanical operating.
EERC sensor : blocked & EELC sensor : blocked
7284 <Escrow>Two or more sensor change was detected EEUC/EELC sensors were following impossible state at the start H or J ESC ES3 EEUC/EELC 301-307,311
simultaneously.(EEUC/EELC) of mechanical operating.
EEUC sensor : blocked & EELC sensor : blocked
72A0 <Escrow>Escrow stopper doesn't thrust. ESPC sensor did not become clear after waiting the specified time H or J ESC ES1 or ES2 ESPC ESMG 001,002,101,102,10
when ESMG solenoid switched on to thrust. 7,108,301-307
72A1 <Escrow>Escrow stopper doesn't escape. ESPC sensor did not become clear after waiting the specified time H or J ESC ES1 or ES2 ESPC ESMG 001,002,101,102,10
when ESMG solenoid switched on to escape. 7,108,301-307
7601 <Reservoir>Media remains at reservoir. Media remaining data of Reservoir memorized by software had S or J Reset with SW ESC 001,002,301-307
been set at the start of a command.
Note was stored in Reservoir when Transport motor was rotated at
Mechanical reset processing.
7681 <Escrow>Media remains at escrow. Media remaining data of Escrow memorized by software had been S or J Reset with SW ESC EECS 001,002,301-307
set at the start of a command.
Note was stored in Escrow when Transport motor was rotated at
Mechanical reset processing.
EECS sensor was blocked after note transport to Separator or Pre-
acceptor from Escrow.
7C01 <Reservoir>Media disappeared from reservoir. EERS/EELS sensors did not detect notes when they were J or H ESC SEP or UT ES4 or ES5 EERS/EELS 001,010,301-307
transported to Top Transport from Reservoir. SSEC
Separator was empty when they were transported to Separator
from Top Transpot.
7C81 <Escrow>Media disappeared from escrow. EERS/EELS sensors did not detect notes when they were J or H ESC SEP or UT ES4 or ES5 EERS/EELS 001,010,301-307
transported to Top Transport from Escrow. SSEC
Separator was empty when they were transported to Separator
from Top Transpot.
8*** Mechanical error at cassette-1

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 26 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
8100 <Cassette1>Cassette stage doesn't move downward. CT1S sensor was not cleared within the specified time when J or H CAS1 CM1 or Cable CS1 or LB1 CT1S BS1M 001,002,005,010-
Cassette 1 Stage moved down. or LPCB 108,111,210-
212,301-307
8101 <Cassette1>Cassette stage doesn't move upward. CT1S sensor was not blocked within the specified time when J or H CAS1 CM1 or Cable CS1 or LB1 CT1S/CP1C/ BS1M 001,002,005,010-
Cassette 1 Stage moved down. or LPCB NE1C 108,111,210-
CP1C sensor was not blocked within the specified time when 212,301-307
Cassette 1 Stage moved up at BRU.
CP1C/NE1C sensors were not blocked within the specified time
when Cassette 1 Stage moved up at BNA.
8120 <Cassette1>Pick up motor rotate but doesn't detect CV1C sensor was not cleared within the specified time while H or J CAS1 CM1 or Cable CS1 or LB1 CV1C BF1M 005,101-108,310-
vaned wheel phase sensor. phase adjustment of Cassette 1 Impeller. 307,309
8180 <Cassette1>Cassette stage doesn't move downward CT1S sensor was not cleared within the specified time when J or H CAS1 CM1 or Cable CS1 or LB1 CT1S BS1M 001,002,005,010-
with compulsory storing. Cassette 1 Stage moved down with compulsory storing. 108,111,210-
212,301-307
8181 <Cassette1>Cassette stage doesn't move upward with CT1S sensor was not blocked within the specified time when J or H CAS1 CM1 or Cable CS1 or LB1 CT1S/CP1C/ BS1M 001,002,005,010-
compulsory storing. Cassette 1 Stage moved down with compulsory storing. NE1C 108,111,210-
CP1C sensor was not blocked within the specified time when 212,301-307
Cassette 1 Stage moved up at BRU with compulsory storing.
CP1C/NE1C sensors were not blocked within the specified time
when Cassette 1 Stage moved up at BNA with compulsory storing.

81FF <Cassette1>Cassette cannot be used. Because the error occurred before, the cassette cannot be operated. H or J CAS1 CM1 or Cable CS1 or LB1 CT1S/CP1C/ BS1M/BF1M 001,002,005,010-
or LPCB NE1C/CF1C 108,111,210-
CV1C 212,301-307
8200 <Cassette1>Detect full sensor at stage press position. CF1C sensor was blocked when Cassette 1 Stage was moved H or J CAS1 Cable CS1 or LB1 CF1C/CP1C BS1M 007,301-307,309
down for Note Empty re-check.
8201 <Cassette1>Two or more sensor change was detected CE1C/NF1C sensors were following impossible state during H or J CAS1 CM1 or Cable CS1 CE1C/NF1C 301-307,309
simultaneously.(CE1C/NF1C) mechanical operation.
CE1C sensor : cleared & NF1C sensor : blocked
8202 <Cassette1>Two or more sensor change was detected NE1C/NF1C sensors were following impossible state during H or J CAS1 CM1 or Cable CS1 NE1C/NF1C 301-307,309
simultaneously.(NE1C/NF1C) mechanical operation at BRU.
NE1C sensor : blocked & NF1C sensor : blocked
8203 <Cassette1>Two or more sensor change was detected NE1C/NF1C sensors were following impossible state during H or J CAS1 CM1 or Cable CS1 NE1C/CF1C 301-307,309
simultaneously.(NE1C/NF1C/CF1C) mechanical operation at BNA.
NE1C sensor : blocked & NF1C sensor : blocked
NE1C/CF1C sensors were following impossible state during
mechanical operation at BRU.
NE1C sensor : blocked & CF1C sensor : blocked
8300 <Cassette1>Feed roller lock release is impossible. CO1C sensor was not blocked after waiting the specified time H or J CAS1 CM1 or Cable CS1 or LB1 CO1C BF1M/C1MG 005,101-108,301-
when C1MG solenoid switched on. 307,309
8400 <Cassette1 Transport>After jam with compulsory After jam is generated on cassette1 transport, the solvent wiping H or J CAS1 CM1 or LB 001,002,012
storing. removal is not done. with compulsory storing.
8E00 <Cassette1>Media remains at Transport of Cassette. CR1S/CL1S sensors were blocking even if BF1M motor was J or H CAS1 CM1 or LB CS1 or LB1 CL1S/CR1S BF1M 001,002,101-
rotated in the storing direction. 108,203-206,301-
307,309

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 27 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
8E01 <Cassette1>Unusual notes remained in cassette. After detecting empty by CE1C sensor, when Cassette 1 Stage J or H CAS1 CM1 or LB CS1 or LB1 CP1C/CE1C/ BS1M 001,002,010,302-
moved down on the specified time, media remains were detected CT1S 306,312
by CT1S sensor.
8E80 <Cassette1>Media remains at Transport of Cassette CR1S/CL1S sensors were blocking even if BF1M motor was J or H CAS1 CM1 or LB CS1 or LB1 CL1S/CR1S BF1M 001,002,101-
with compulsory storing. rotated in the storing direction with compulsory storing. 108,203-206,301-
307,309
8F00 <Cassette1>Cannot pick up note from cassette even CR1S/CL1S sensors were not blocked within the specified time J or H CAS1 CM1 or Cable CS1 or LB1 CP1C/CE1C BF1M 002,007,010,012,20
retry 60-times. when picked up notes from Cassette 1. or LB 3-206,312
8F01 <Cassette1>Unusual notes remained. The empty was detected when transporting notes from Cassette 1, H or J CAS1 Cable or LB CS1 or LB1 CP1C/CE1C BF1M 001,002,010,302-
but it was not empty when operating the mechanism after that. 306,312
8F02 <Cassette1>Poor rotation of motor. Step-out was detected at CS1C sensor during BF1M motor H or J CAS1 CM1 or Cable CS1 or LB1 CS1C BF1M 002,005,007,010,01
rotating. or LB 2,101-108,203-
206,301-307,309
8F03 <Cassette1>The number of not recognized notes in The number of not recognized notes reached the maximum H or S BV CAS1 or Cable 006,010,011
Cassette1 was exceeded. number while notes were transported from Cassette 1.
8F04 <Cassette1>The number of damaged notes in Cassette1 The number of damaged notes reached the maximum number H or S BV CAS1 or Cable 006,007,010,011,01
was exceeded. when notes were transported from Cassette 1. 2,201-208,224
8F05 <Cassette1>The number of different denomination The number of different denomination notes reached the H or S BV CAS1 or Cable 006,011
notes in Cassette1 was exceeded. maximum number when notes were transported from Cassette 1.
8F06 <Cassette1>The number of counterfeit notes in The number of counterfeit notes reached the maximum number H or S BV CAS1 or Cable 006,011
Cassette1 was exceeded. when notes were transported from Cassette 1.
8F07 <Cassette1>The number of rejected notes for payment The number of notes that were transported from Cassette 1 and H or S BV CAS1 or Cable 006,011
in Cassette1 was exceeded. stored in areas other than Escrow reached 30 at dispensing.
8F10 <Cassette1>The number of notes for payment in Cassette 1 became empty before dispensing the number of notes H or S CAS1 Cable CS1 CP1C/CE1C 006,011
Cassette1 was insufficient. requested.
9*** Mechanical error at cassette-2
9100 <Cassette2>Cassette stage doesn't move downward. CT2S sensor was not cleared within the specified time when J or H CAS2 CM2 or Cable CS2 or LB1 CT2S BS2M 001,002,005,010-
Cassette 2 Stage moved down. or LPCB 108,111,210-
212,301-307
9101 <Cassette2>Cassette stage doesn't move upward. CT2S sensor was not blocked within the specified time when J or H CAS2 CM2 or Cable CS2 or LB1 CT2S/CP2C/ BS2M 001,002,005,010-
Cassette 2 Stage moved down. or LPCB NE2C 108,111,210-
CP2C sensor was not blocked within the specified time when 212,301-307
Cassette 2 Stage moved up at BRU.
CP2C/NE2C sensors were not blocked within the specified time
when Cassette 2 Stage moved up at BNA.
9120 <Cassette2>Pick up motor rotate but doesn't detect CV2C sensor was not cleared within the specified time while H or J CAS2 CM2 or Cable CS2 or LB1 CV2C BF2M 005,101-108,310-
vaned wheel phase sensor. phase adjustment of Cassette 2 Impeller. 307,309
9180 <Cassette2>Cassette stage doesn't move downward CT2S sensor was not cleared within the specified time when J or H CAS2 CM2 or Cable CS2 or LB1 CT2S BS2M 001,002,005,010-
with compulsory storing. Cassette 2 Stage moved down with compulsory storing. 108,111,210-
212,301-307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 28 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
9181 <Cassette2>Cassette stage doesn't move upward with CT2S sensor was not blocked within the specified time when J or H CAS2 CM2 or Cable CS2 or LB1 CT2S/CP2C/ BS2M 001,002,005,010-
compulsory storing. Cassette 2 Stage moved down with compulsory storing. NE2C 108,111,210-
CP2C sensor was not blocked within the specified time when 212,301-307
Cassette 2 Stage moved up at BRU with compulsory storing.
CP2C/NE2C sensors were not blocked within the specified time
when Cassette 2 Stage moved up at BNA with compulsory storing.

91FF <Cassette2>Cassette cannot be used. Because the error occurred before, the cassette cannot be operated. H or J CAS2 CM2 or Cable CS2 or LB1 CT2S/CP2C/ BS2M/BF2M 001,002,005,010-
or LPCB NE2C/CF2C 108,111,210-
CV2C 212,301-307
9200 <Cassette2>Detect full sensor at stage press position. CF2C sensor was blocked when Cassette 2 Stage was moved H or J CAS2 Cable CS2 or LB1 CF2C/CP2C BS2M 007,301-307,309
down for Note Empty re-check.
9201 <Cassette2>Two or more sensor change was detected CE2C/NF2C sensors were following impossible state during H or J CAS2 CM2 or Cable CS2 CE2C/NF2C 301-307,309
simultaneously.(CE2C/NF2C) mechanical operation.
CE2C sensor : cleared & NF2C sensor : blocked
9202 <Cassette2>Two or more sensor change was detected NE2C/NF2C sensors were following impossible state during H or J CAS2 CM2 or Cable CS2 NE2C/NF2C 301-307,309
simultaneously.(NE2C/NF2C) mechanical operation at BRU.
NE2C sensor : blocked & NF2C sensor : blocked
9203 <Cassette2>Two or more sensor change was detected NE2C/NF2C sensors were following impossible state during H or J CAS2 CM2 or Cable CS2 NE2C/CF2C 301-307,309
simultaneously.(NE2C/NF2C/CF2C) mechanical operation at BNA.
NE2C sensor : blocked & NF2C sensor : blocked
NE2C/CF2C sensors were following impossible state during
mechanical operation at BRU.
NE2C sensor : blocked & CF2C sensor : blocked
9300 <Cassette2>Feed roller lock release is impossible CO2C sensor was not blocked after waiting the specified time H or J CAS2 CM2 or Cable CS2 or LB1 CO2C BF2M/C2MG 005,101-108,301-
when C2MG solenoid switched on. 307,309
9400 <Cassette2 Transport>After jam with compulsory After jam is generated on cassette2 transport, the solvent wiping H or J CAS2 CM2 or LB CS2 or LB1 001,002,012
storing. removal is not done. with compulsory storing.
9E00 <Cassette2>Media remains at Transport of Cassette. CR2S/CL2S sensors were blocking even if BF2M motor was J or H CAS2 CM2 or LB CS2 or LB1 CL2S/CR2S BF2M 001,002,101-
rotated in the storing direction. 108,203-206,301-
307,309
9E01 <Cassette2>Unusual notes remained in cassette. After detecting empty by CE2C sensor, when Cassette 2 Stage J or H CAS2 CM2 or LB CS2 or LB1 CP2C/CE2C/ BS2M 001,002,010,302-
moved down on the specified time, media remains were detected CT2S 306,312
by CT2S sensor.
9E80 <Cassette2>Media remains at Transport of Cassette CR2S/CL2S sensors were blocking even if BF2M motor was J or H CAS2 CM2 or LB CS2 or LB1 CL2S/CR2S BF2M 001,002,101-
with compulsory storing. rotated in the storing direction with compulsory storing. 108,203-206,301-
307,309
9F00 <Cassette2>Cannot pick up note from cassette even CR2S/CL2S sensors were not blocked within the specified time J or H CAS2 CM2 or Cable CS2 or LB1 CP2C/CE2C BF2M 002,007,010,012,20
retry 60-times. when picked up notes from Cassette 2. or LB 3-206,312
9F01 <Cassette2>Unusual notes remained The empty was detected when transporting notes from Cassette 2, H or J CAS2 Cable or LB CS2 or LB1 CP2C/CE2C BF2M 001,002,010,302-
but it was not empty when operating the mechanism after that. 306,312
9F02 <Cassette2>Poor rotation of motor Step-out was detected at CS2C sensor during BF2M motor H or J CAS2 CM2 or Cable CS2 or LB1 CS2C BF2M 002,005,007,010,01
rotating. or LB 2,101-108,203-
206,301-307,309
9F03 <Cassette2>The number of not recognized notes in The number of not recognized notes reached the maximum H or S BV CAS2 or Cable 006,010,011
Cassette2 was exceeded. number while notes were transported from Cassette 2.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 29 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
9F04 <Cassette2>The number of damaged notes in Cassette2 The number of damaged notes reached the maximum number H or S BV CAS2 or Cable 006,007,010,011,01
was exceeded. when notes were transported from Cassette 2. 2,201-208,224
9F05 <Cassette2>The number of different denomination The number of different denomination notes reached the H or S BV CAS2 or Cable 006,011
notes in Cassette2 was exceeded. maximum number when notes were transported from Cassette 2.
9F06 <Cassette2>The number of counterfeit notes in The number of counterfeit notes reached the maximum number H or S BV CAS2 or Cable 006,011
Cassette2 was exceeded. when notes were transported from Cassette 2.
9F07 <Cassette2>The number of rejected notes for payment The number of notes that were transported from Cassette 2 and H or S BV CAS2 or Cable 006,011
in Cassette2 was exceeded. stored in areas other than Escrow reached 30 at dispensing.
9F10 <Cassette2>The number of notes for payment in Cassette 2 became empty before dispensing the number of notes H or S CAS2 Cable CS2 CP2C/CE2C 006,011
Cassette2 was insufficient. requested.
A*** Mechanical error at cassette-3
A100 <Cassette3>Cassette stage doesn't move downward. CT3S sensor was not cleared within the specified time when J or H CAS3 CM3 or Cable CS3 or LB3 CT3S BS3M 001,002,005,010-
Cassette 3 Stage moved down. or LPCB 108,111,210-
212,301-307
A101 <Cassette3>Cassette stage doesn't move upward. CT3S sensor was not blocked within the specified time when J or H CAS3 CM3 or Cable CS3 or LB3 CT3S/CP3C/ BS3M 001,002,005,010-
Cassette 3 Stage moved down. or LPCB NE3C 108,111,210-
CP3C sensor was not blocked within the specified time when 212,301-307
Cassette 3 Stage moved up at BRU.
CP3C/NE3C sensors were not blocked within the specified time
when Cassette 3 Stage moved up at BNA.
A120 <Cassette3>Pick up motor rotate but doesn't detect CV3C sensor was not cleared within the specified time while H or J CAS3 CM3 or Cable CS3 or LB3 CV3C BF3M 005,101-108,310-
vaned wheel phase sensor. phase adjustment of Cassette 3 Impeller. 307,309
A180 <Cassette3>Cassette stage doesn't move downward CT3S sensor was not cleared within the specified time when J or H CAS3 CM3 or Cable CS3 or LB3 CT3S BS3M 001,002,005,010-
with compulsory storing. Cassette 3 Stage moved down with compulsory storing. 108,111,210-
212,301-307
A181 <Cassette3>Cassette stage doesn't move upward with CT3S sensor was not blocked within the specified time when J or H CAS3 CM3 or Cable CS3 or LB3 CT3S/CP3C/ BS3M 001,002,005,010-
compulsory storing. Cassette 3 Stage moved down with compulsory storing. NE3C 108,111,210-
CP3C sensor was not blocked within the specified time when 212,301-307
Cassette 3 Stage moved up at BRU with compulsory storing.
CP3C/NE3C sensors were not blocked within the specified time
when Cassette 3 Stage moved up at BNA with compulsory storing.

A1FF <Cassette3>Cassette cannot be used. Because the error occurred before, the cassette cannot be operated. H or J CAS3 CM3 or Cable CS3 or LB3 CT3S/CP3C/ BS3M/BF3M 001,002,005,010-
or LPCB NE3C/CF3C 108,111,210-
CV3C 212,301-307
A200 <Cassette3>Detect full sensor at stage press position. CF3C sensor was blocked when Cassette 3 Stage was moved H or J CAS3 Cable CS3 or LB3 CF3C/CP3C BS3M 007,301-307,309
down for Note Empty re-check.
A201 <Cassette3>Two or more sensor change was detected CE3C/NF3C sensors were following impossible state during H or J CAS3 CM3 or Cable CS3 CE3C/NF3C 301-307,309
simultaneously.(CE3C/NF3C) mechanical operation.
CE3C sensor : cleared & NF3C sensor : blocked
A202 <Cassette3>Two or more sensor change was detected NE3C/NF3C sensors were following impossible state during H or J CAS3 CM3 or Cable CS3 NE3C/NF3C 301-307,309
simultaneously.(NE3C/NF3C) mechanical operation at BRU.
NE3C sensor : blocked & NF3C sensor : blocked

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 30 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
A203 <Cassette3>Two or more sensor change was detected NE3C/NF3C sensors were following impossible state during H or J CAS3 CM3 or Cable CS3 NE3C/CF3C 301-307,309
simultaneously.(NE3C/NF3C/CF3C) mechanical operation at BNA.
NE3C sensor : blocked & NF3C sensor : blocked
NE3C/CF3C sensors were following impossible state during
mechanical operation at BRU.
NE3C sensor : blocked & CF3C sensor : blocked
A300 <Cassette3>Feed roller lock release is impossible CO3C sensor was not blocked after waiting the specified time H or J CAS3 CM3 or Cable CS3 or LB3 CO3C BF3M/C3MG 005,101-108,301-
when C3MG solenoid switched on. 307,309
A400 <Cassette3 Transport>After jam with compulsory After jam is generated on cassette3 transport, the solvent wiping H or J CAS3 CM3 or LB 001,002,012
storing. removal is not done. with compulsory storing.
AE00 <Cassette3>Media remains at Transport of Cassette. CR3S/CL3S sensors were blocking even if BF3M motor was J or H CAS3 CM3 or LB CS3 or LB3 CL3S/CR3S BF3M 001,002,101-
rotated in the storing direction. 108,203-206,301-
307,309
AE01 <Cassette3>Unusual notes remained in cassette. After detecting empty by CE3C sensor, when Cassette 3 Stage J or H CAS3 CM3 or LB CS3 or LB3 CP3C/CE3C/ BS3M 001,002,010,302-
moved down on the specified time, media remains were detected CT3S 306,312
by CT3S sensor.
AE80 <Cassette3>Media remains at Transport of Cassette CR3S/CL3S sensors were blocking even if BF3M motor was J or H CAS3 CM3 or LB CS3 or LB3 CL3S/CR3S BF3M 001,002,101-
with compulsory storing. rotated in the storing direction with compulsory storing. 108,203-206,301-
307,309
AF00 <Cassette3>Cannot pick up note from cassette even CR3S/CL3S sensors were not blocked within the specified time J or H CAS3 CM3 or Cable CS3 or LB3 CP3C/CE3C BF3M 002,007,010,012,20
retry 60-times. when picked up notes from Cassette 3. or LB 3-206,312
AF01 <Cassette3>Unusual notes remained The empty was detected when transporting notes from Cassette 3, H or J CAS3 Cable or LB CS3 or LB3 CP3C/CE3C BF3M 001,002,010,302-
but it was not empty when operating the mechanism after that. 306,312
AF02 <Cassette3>Poor rotation of motor Step-out was detected at CS3C sensor during BF3M motor H or J CAS3 CM3 or Cable CS3 or LB3 CS3C BF3M 002,005,007,010,01
rotating. or LB 2,101-108,203-
206,301-307,309
AF03 <Cassette3>The number of not recognized notes in The number of not recognized notes reached the maximum H or S BV CAS3 or Cable 006,010,011
Cassette3 was exceeded. number while notes were transported from Cassette 3.
AF04 <Cassette3>The number of damaged notes in Cassette3 The number of damaged notes reached the maximum number H or S BV CAS3 or Cable 006,007,010,011,01
was exceeded. when notes were transported from Cassette 3. 2,201-208,224
AF05 <Cassette3>The number of different denomination The number of different denomination notes reached the H or S BV CAS3 or Cable 006,011
notes in Cassette3 was exceeded. maximum number when notes were transported from Cassette 3.
AF06 <Cassette3>The number of counterfeit notes in The number of counterfeit notes reached the maximum number H or S BV CAS3 or Cable 006,011
Cassette3 was exceeded. when notes were transported from Cassette 3.
AF07 <Cassette3>The number of rejected notes for payment The number of notes that were transported from Cassette 3 and H or S BV CAS3 or Cable 006,011
in Cassette3 was exceeded. stored in areas other than Escrow reached 30 at dispensing.
AF10 <Cassette3>The number of notes for payment in Cassette 3 became empty before dispensing the number of notes H or S CAS3 Cable CS3 CP3C/CE3C 006,011
Cassette3 was insufficient. requested.
B*** Mechanical error at cassette-4
B100 <Cassette4>Cassette stage doesn't move downward. CT4S sensor was not cleared within the specified time when J or H CAS4 CM4 or Cable CS4 or LB4 CT4S BS4M 001,002,005,010-
Cassette 4 Stage moved down. or LPCB 108,111,210-
212,301-307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 31 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
B101 <Cassette4>Cassette stage doesn't move upward. CT4S sensor was not blocked within the specified time when J or H CAS4 CM4 or Cable CS4 or LB4 CT4S/CP4C/ BS4M 001,002,005,010-
Cassette 4 Stage moved down. or LPCB NE4C 108,111,210-
CP4C sensor was not blocked within the specified time when 212,301-307
Cassette 4 Stage moved up at BRU.
CP4C/NE4C sensors were not blocked within the specified time
when Cassette 4 Stage moved up at BNA.
B120 <Cassette4>Pick up motor rotate but doesn't detect CV4C sensor was not cleared within the specified time while H or J CAS4 CM4 or Cable CS4 or LB4 CV4C BF4M 005,101-108,310-
vaned wheel phase sensor. phase adjustment of Cassette 4 Impeller. 307,309
B180 <Cassette4>Cassette stage doesn't move downward CT4S sensor was not cleared within the specified time when J or H CAS4 CM4 or Cable CS4 or LB4 CT4S BS4M 001,002,005,010-
with compulsory storing. Cassette 4 Stage moved down with compulsory storing. 108,111,210-
212,301-307
B181 <Cassette4>Cassette stage doesn't move upward with CT4S sensor was not blocked within the specified time when J or H CAS4 CM4 or Cable CS4 or LB4 CT4S/CP4C/ BS4M 001,002,005,010-
compulsory storing. Cassette 4 Stage moved down with compulsory storing. NE4C 108,111,210-
CP4C sensor was not blocked within the specified time when 212,301-307
Cassette 4 Stage moved up at BRU with compulsory storing.
CP4C/NE4C sensors were not blocked within the specified time
when Cassette 4 Stage moved up at BNA with compulsory storing.

B1FF <Cassette4>Cassette cannot be used. Because the error occurred before, the cassette cannot be operated. H or J CAS4 CM4 or Cable CS4 or LB4 CT4S/CP4C/ BS4M/BF4M 001,002,005,010-
or LPCB NE4C/CF4C 108,111,210-
CV4C 212,301-307
B200 <Cassette4>Detect full sensor at stage press position. CF4C sensor was blocked when Cassette 4 Stage was moved H or J CAS4 Cable CS4 or LB4 CF4C/CP4C BS4M 007,301-307,309
down for Note Empty re-check.
B201 <Cassette4>Two or more sensor change was detected CE4C/NF4C sensors were following impossible state during H or J CAS4 CM4 or Cable CS4 CE4C/NF4C 301-307,309
simultaneously.(CE4C/NF4C) mechanical operation.
CE4C sensor : cleared & NF4C sensor : blocked
B202 <Cassette4>Two or more sensor change was detected NE4C/NF4C sensors were following impossible state during H or J CAS4 CM4 or Cable CS4 NE4C/NF4C 301-307,309
simultaneously.(NE4C/NF4C) mechanical operation at BRU.
NE4C sensor : blocked & NF4C sensor : blocked
B203 <Cassette4>Two or more sensor change was detected NE4C/NF4C sensors were following impossible state during H or J CAS4 CM4 or Cable CS4 NE4C/CF4C 301-307,309
simultaneously.(NE4C/NF4C/CF4C) mechanical operation at BNA.
NE4C sensor : blocked & NF4C sensor : blocked
NE4C/CF4C sensors were following impossible state during
mechanical operation at BRU.
NE4C sensor : blocked & CF4C sensor : blocked
B300 <Cassette4>Feed roller lock release is impossible CO4C sensor was not blocked after waiting the specified time H or J CAS4 CM4 or Cable CS4 or LB4 CO4C BF4M/C4MG 005,101-108,301-
when C4MG solenoid switched on. 307,309
B400 <Cassette4 Transport>After jam with compulsory After jam is generated on cassette4 transport, the solvent wiping H or J CAS4 CM4 or LB CS4 or LB4 001,002,012
storing. removal is not done. with compulsory storing.
BE00 <Cassette4>Media remains at Transport of Cassette. CR4S/CL4S sensors were blocking even if BF4M motor was J or H CAS4 CM4 or LB CS4 or LB4 CL4S/CR4S BF4M 001,002,101-
rotated in the storing direction. 108,203-206,301-
307,309
BE01 <Cassette4>Unusual notes remained in cassette. After detecting empty by CE4C sensor, when Cassette 4 Stage J or H CAS4 CM4 or LB CS4 or LB4 CP4C/CE4C/ BS4M 001,002,010,302-
moved down on the specified time, media remains were detected CT4S 306,312
by CT4S sensor.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 32 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
BE80 <Cassette4>Media remains at Transport of Cassette CR4S/CL4S sensors were blocking even if BF4M motor was J or H CAS4 CM4 or LB CS4 or LB4 CL4S/CR4S BF4M 001,002,101-
with compulsory storing. rotated in the storing direction with compulsory storing. 108,203-206,301-
307,309
BF00 <Cassette4>Cannot pick up note from cassette even CR4S/CL4S sensors were not blocked within the specified time J or H CAS4 CM4 or Cable CS4 or LB4 CP4C/CE4C BF4M 002,007,010,012,20
retry 60-times. when picked up notes from Cassette 4. or LB 3-206,312
BF01 <Cassette4>Unusual notes remained The empty was detected when transporting notes from Cassette 4, H or J CAS1 Cable or LB CS4 or LB4 CP4C/CE4C BF4M 001,002,010,302-
but it was not empty when operating the mechanism after that. 306,312
BF02 <Cassette4>Poor rotation of motor Step-out was detected at CS4C sensor during BF4M motor H or J CAS4 CM4 or Cable CS4 or LB4 CS4C BF4M 002,005,007,010,01
rotating. or LB 2,101-108,203-
206,301-307,309
BF03 <Cassette4>The number of not recognized notes in The number of not recognized notes reached the maximum H or S BV CAS4 or Cable 006,010,011
Cassette4 was exceeded. number while notes were transported from Cassette 4.
BF04 <Cassette4>The number of damaged notes in Cassette4 The number of damaged notes reached the maximum number H or S BV CAS4 or Cable 006,007,010,011,01
was exceeded. when notes were transported from Cassette 4. 2,201-208,224
BF05 <Cassette4>The number of different denomination The number of different denomination notes reached the H or S BV CAS4 or Cable 006,011
notes in Cassette4 was exceeded. maximum number when notes were transported from Cassette 4.
BF06 <Cassette4>The number of counterfeit notes in The number of counterfeit notes reached the maximum number H or S BV CAS4 or Cable 006,011
Cassette4 was exceeded. when notes were transported from Cassette 4.
BF07 <Cassette4>The number of rejected notes for payment The number of notes that were transported from Cassette 4 and H or S BV CAS4 or Cable 006,011
in Cassette4 was exceeded. stored in areas other than Escrow reached 30 at dispensing.
BF10 <Cassette4>The number of notes for payment in Cassette 4 became empty before dispensing the number of notes H or S CAS4 Cable CS4 CP4C/CE4C 006,011
Cassette4 was insufficient. requested.
C*** Des relation
C001 <DES>Encryption key is not set. Encryption key was not set when DES encryption mode was H or S LPCB 008,313,314
specified.
E1** Jam, detect unexpected note or note teared.
E001 <BV>Validation data error No validation data from BV when notes were detected at UGAS H or C BV LPCB BV LAN 315-318,011
sensor during note transport.
E101 <Cassette1 Transport>Jam, detect unexpected note or During note transport, CR1S/CL1S sensors were blocked although J CAS1 LT CR1S/CL1S 001,002,010,012,10
note teared at CR1S/CL1S sensor. notes could not have reached them. 3,107,108,203-209,
226,301-304,306,
307,309,311
E102 <Cassette2 Transport>Jam, detect unexpected note or During note transport, CR2S/CL2S sensors were blocked although J CAS2 LT CR2S/CL2S 001,002,010,012,10
note teared at CR2S/CL2S sensor. notes could not have reached them. 3,107,108,203-209,
226,301-304,306,
307,309,311
E103 <Cassette3 Transport>Jam, detect unexpected note or During note transport, CR3S/CL3S sensors were blocked although J CAS3 LT CR3S/CL3S 001,002,010,012,10
note teared at CR3S/CL3S sensor. notes could not have reached them. 3,107,108,203-209,
226,301-304,306,
307,309,311
E104 <Cassette4 Transport>Jam, detect unexpected note or During note transport, CR4S/CL4S sensors were blocked although J CAS4 LT CR4S/CL4S 001,002,010,012,10
note teared at CR4S/CL4S sensor. notes could not have reached them. 3,107,108,203-209,
226,301-304,306,
307,309,311

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 33 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
E105 <Transport after BV>Jam, detect unexpected note or During note transport, UGAS sensor was blocked although notes J UT BV or BVE UGAS 001,002,010,103-
note teared at UGAS sensor. could not have reached them. 108,201-
206,224,301-
304,306,307,311
E106 <Escrow Transport>Jam, detect unexpected note or During note transport, ERRS/ERLS sensors were blocked J ESC UT or ERRS/ERLS 001,002,010,103-
note teared at ERRS/ERLS sensor. although notes could not have reached them. SPCB 108,201-
208,224,301-
304,306,307,311
E107 <Escrow Transport>Jam, detect unexpected note or During note transport, EDRS/EDLS sensors were blocked J ESC UT EDRS/EDLS 001,002,010,103-
note teared at EDRS/EDLS sensor. although notes could not have reached them. 108,201-
208,224,301-
304,306,307,311
E108 <Reject Transport>Jam, detect unexpected note or note During note transport, UGDS sensor was blocked although notes J UT RJ Bin UGDS 001,002,010,103-
teared at UGDS sensor. could not have reached them. 108,201-
208,224,301-
304,306,307,311
E109 <Reject Transport>Jam, detect unexpected note or note During note transport, UEFS sensor was blocked although notes J UT RJ Bin UEFS 001,002,010,103-
teared at UEFS sensor. could not have reached them. 108,201-
208,224,301-
304,306,307,311
E10A <Reject Transport>Jam, detect unexpected note or note During note transport, UERS sensor was blocked although notes J UT RJ Bin UERS 001,002,010,103-
teared at UERS sensor. could not have reached them. 108,201-
208,224,301-
304,306,307,311
E10B <Reject Transport>Jam, detect unexpected note or note During note transport, UECS sensor was blocked although notes J UT RJ Bin UECS 001,002,010,103-
teared at UECS sensor. could not have reached them. 108,201-
208,224,301-
304,306,307,311
E10C <Cassettes Transport>Jam, detect unexpected note or During note transport, URHS sensor was blocked although notes J UT LT URHS 001,002,009,010,10
note teared at URHS sensor. could not have reached them. 3-108,201-
206,224,301-
304,306,307,311
E10D <Transport before BV>Jam, detect unexpected note or During note transport, UFHS sensor was blocked although notes J UT LT UFHS 001,002,009,010,10
note teared at UFHS sensor. could not have reached them. 3-108,201-
206,224,301-
304,306,307,311
E10E <Cassette3 Transport>Jam, detect unexpected note or During note transport, LT3S sensor was blocked although notes J LT UT LT3S 001,002,009,010,10
note teared at LT3S sensor. could not have reached them. 3-108,201-
208,224,301-
304,306,307,311
E10F <Separator Transport>Jam, detect unexpected note or During note transport, SSRS/SSLS/SSOS sensors were blocked J SEP SSRS/SSLS/ 001,002,010,012,10
note teared at SSRS/SSLS/SSOS sensor. although notes could not have reached them. SSOS 3-108,201-206,301-
304,306,307,311

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 34 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
E110 <BV Transport>Jam, detect unexpected note or note During note transport, BVIN sensor was blocked although notes J BV BVE or SEP or BVIN 001,002,010,011,10
teared at BVIN sensor. could not have reached them. LT 3-108,201-
206,224,301-
304,306,307,311
E111 <Separator Transport>Jam, detect unexpected note or During note transport, SDIS sensor was blocked although notes J SEP SDIS 001,002,010,012,10
note teared at SDIS sensor. could not have reached them. 3-108,201-206,301-
304,306,307,311
E112 <Cassette1 Transport>Jam, detect unexpected note or During note transport, CR1S/CL1S sensors were blocked although J CAS1 LT CR1S/CL1S 001,002,010,012,10
note teared at CR1S/CL1S sensor with compulsory notes could not have reached them with compulsory storing. 3,107,108,203-209,
storing. 226,301-304,306,
307,309,311
E113 <Cassette2 Transport>Jam, detect unexpected note or During note transport, CR2S/CL2S sensors were blocked although J CAS2 LT CR2S/CL2S 001,002,010,012,10
note teared at CR2S/CL2S sensor with compulsory notes could not have reached them with compulsory storing. 3,107,108,203-209,
storing. 226,301-304,306,
307,309,311
E114 <Cassette3 Transport>Jam, detect unexpected note or During note transport, CR3S/CL3S sensors were blocked although J CAS3 LT CR3S/CL3S 001,002,010,012,10
note teared at CR3S/CL3S sensor with compulsory notes could not have reached them with compulsory storing. 3,107,108,203-209,
storing. 226,301-304,306,
307,309,311
E115 <Cassette4 Transport>Jam, detect unexpected note or During note transport, CR4S/CL4S sensors were blocked although J CAS4 LT CR4S/CL4S 001,002,010,012,10
note teared at CR4S/CL4S sensor with compulsory notes could not have reached them with compulsory storing. 3,107,108,203-209,
storing. 226,301-304,306,
307,309,311
E2** Jam, note doesn't reach to the sensor in time.
E201 <Cassette1 Transport>Jam, note doesn't reach to During note transport, notes did not reach CR1S/CL1S sensors J CAS1 LT or UT CR1S/CL1S 001,002,010,012,10
CR1S/CL1S sensor. within the specified time resulting in timeout. 3,107,108,203-
209,226,302,306,30
7,309
E202 <Cassette2 Transport>Jam, note doesn't reaed to During note transport, notes did not reach CR2S/CL2S sensors J CAS2 LT or UT CR2S/CL2S 001,002,010,012,10
CR2S/CL2S sensor. within the specified time resulting in timeout. 3,107,108,203-
209,226,302,306,30
7,309
E203 <Cassette3 Transport>Jam, note doesn't reach to During note transport, notes did not reach CR3S/CL3S sensors J CAS3 LT or UT CR3S/CL3S 001,002,010,012,10
CR3S/CL3S sensor. within the specified time resulting in timeout. 3,107,108,203-
209,226,302,306,30
7,309
E204 <Cassette4 Transport>Jam, note doesn't reach to During note transport, notes did not reach CR4S/CL4S sensors J CAS4 LT or UT CR4S/CL4S 001,002,010,012,10
CR4S/CL4S sensor. within the specified time resulting in timeout. 3,107,108,203-
209,226,302,306,30
7,309
E205 <BV Transport>Jam, note doesn't reach to UGAS During note transport, notes did not reach UGAS sensor within the J BVE BV or SEP UGAS 001,002,010,103-
sensor. specified time resulting in timeout. 108,201-206,224,
302,306,307
E206 <Escrow Transport>Jam, note doesn't reach to During note transport, notes did not reach ERRS/ERLS sensors J ESC UT ERRS/ERLS 001,002,010,103-
ERRS/ERLS sensor. within the specified time resulting in timeout. 108,201-208,224,
302,306,307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 35 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
E207 <Escrow Transport>Jam, note doesn't reacd to During note transport, notes did not reach EDRS/EDLS sensors J ESC UT EDRS/EDLS 001,002,010,103-
EDRS/EDLS sensor. within the specified time resulting in timeout. 108,201-208,224,
302,306,307
E208 <Reject Transport>Jam, note doesn't reach to UGDS During note transport, notes did not reach UGDS sensor within the J UT UGDS 001,002,010,103-
sensor. specified time resulting in timeout. 108,201-208,224,
302,306,307
E209 <Reject Transport>Jam, note doesn't reach to UEFS During note transport, notes did not reach UEFS sensor within the J UT RJ Bin UEFS 001,002,010,103-
sensor. specified time resulting in timeout. 108,201-208,224,
302,306,307
E20A <Reject Transport>Jam, note doesn't reach to UERS During note transport, notes did not reach UERS sensor within the J UT RJ Bin UERS 001,002,010,103-
sensor. specified time resulting in timeout. 108,201-208,224,
302,306,307
E20B <Reject Transport>Jam, note doesn't reach to UECS During note transport, notes did not reach UECS sensor within the J UT RJ Bin UECS 001,002,010,103-
sensor. specified time resulting in timeout. 108,201-208,224,
302,306,307
E20C <Cassettes Transport>Jam, note doesn't reach to URHS During note transport, notes did not reach URHS sensor within the J UT URHS 001,002,009,010,10
sensor. specified time resulting in timeout. 3-108,201-206,224,
302,306,307
E20D <Transport before BV>Jam, note doesn't reach to During note transport, notes did not reach UFHS sensor within the J LT UT UFHS 001,002,009,010,10
UFHS sensor. specified time resulting in timeout. 3-108,201-206,224,
302,306,307
E20E <Cassette3 Transport>Jam, note doesn't reach to LT3S During note transport, notes did not reach LT3S sensor within the J CAS LT LT3S 001,002,009,010,10
sensor. specified time resulting in timeout. 3-108,201-208,224,
302,306,307
E20F <Transport before BV>Jam, note doesn't reach to BVIN During note transport, notes did not reach BVIN sensor within the J BVE BV or SEP or BVIN 001,002,010,011,10
sensor. specified time resulting in timeout. LT 3-108,201-206,224,
302,306,307
E210 <Separator Transport>Jam, note doesn't reach to SDIS During note transport, notes did not reach SDIS sensor within the J SEP SDIS 001,002,010,012,10
sensor. specified time resulting in timeout. 3-108,201-
206,302,306,307
E211 <Reject area>Reject area full is detected during note During note transport, notes did not reach UERS sensor within the J UT RJ Bin UERS 001,002,007,010,10
transport. (Jam, note doesn't reach to UERS sensor.) specified time resulting in timeout, and then URFC sensor was 3-108,201-
blocked. 208,224,225,227,30
1-307
E212 <Counterfeit area>Counterfeit area full is detected During note transport, notes did not reach UEFS sensor within the J UT RJ Bin UEFS 001,002,007,010,10
during note transport. (Jam, note doesn't reach to UEFS specified time resulting in timeout, and then UFFC sensor was 3-108,201-
sensor.) blocked. 208,224,225,227,30
1-307
E213 <Captured area>Captured area full is detected during During note transport, notes did not reach UECS sensor within the J UT RJ Bin UECS 001,002,007,010,10
note transport. (Jam, note doesn't reach to UECS specified time resulting in timeout, and then UCFC sensor was 3-108,201-
sensor.) blocked. 208,224,225,227,30
1-307
E214 <Cassette1 Transport>Jam, note doesn't reach to During note transport, notes did not reach CR1S/CL1S sensors J CAS1 LT or UT CR1S/CL1S 001,002,010,012,10
CR1S/CL1S sensor with compulsory storing. within the specified time resulting in timeout with compulsory 3,107,108,203-
storing. 209,226,302,306,30
7,309

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 36 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
E215 <Cassette2 Transport>Jam, note doesn't reaed to During note transport, notes did not reach CR2S/CL2S sensors J CAS2 LT or UT CR2S/CL2S 001,002,010,012,10
CR2S/CL2S sensor with compulsory storing. within the specified time resulting in timeout with compulsory 3,107,108,203-
storing. 209,226,302,306,30
7,309
E216 <Cassette3 Transport>Jam, note doesn't reach to During note transport, notes did not reach CR3S/CL3S sensors J CAS3 LT or UT CR3S/CL3S 001,002,010,012,10
CR3S/CL3S sensor with compulsory storing. within the specified time resulting in timeout with compulsory 3,107,108,203-
storing. 209,226,302,306,30
7,309
E217 <Cassette4 Transport>Jam, note doesn't reach to During note transport, notes did not reach CR4S/CL4S sensors J CAS4 LT or UT CR4S/CL4S 001,002,010,012,10
CR4S/CL4S sensor with compulsory storing. within the specified time resulting in timeout with compulsory 3,107,108,203-
storing. 209,226,302,306,30
7,309
E3** Jam, note doesn't pass through the sensor in
time.
E301 <Cassette1 Transport>Jam, note doesn't pass through During note transport, CR1S/CL1S sensors did not become clear J CAS1 LT CR1S/CL1S 001,002,010,012,10
CR1S/CL1S sensor. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout. 226,301-304,306,
307,309,311
E302 <Cassette2 Transport>Jam, note doesn't pass through During note transport, CR2S/CL2S sensors did not become clear J CAS2 LT CR2S/CL2S 001,002,010,012,10
CR2S/CL2S sensor. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout. 226,301-304,306,
307,309,311
E303 <Cassette3 Transport>Jam, note doesn't pass through During note transport, CR3S/CL3S sensors did not become clear J CAS3 LT CR3S/CL3S 001,002,010,012,10
CR3S/CL3S sensor. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout. 226,301-304,306,
307,309,311
E304 <Cassette4 Transport>Jam, note doesn't pass through During note transport, CR4S/CL4S sensors did not become clear J CAS4 LT CR4S/CL4S 001,002,010,012,10
CR4S/CL4S sensor. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout. 226,301-304,306,
307,309,311
E305 <Escrow Transport>Jam, note doesn't pass through During note transport, ERRS/ERLS sensors did not become clear J ESC UT ERRS/ERLS 001,002,010,103-
ERRS/ERLS sensor. within the specified time after they were blocked, resulting in 108,201-
timeout. 208,224,301-
304,306,307,311
E306 <Escrow Transport>Jam, note doesn't pass through During note transport, EDRS/EDLS sensors did not become clear J ESC UT EDRS/EDLS 001,002,010,103-
EDRS/EDLS sensor. within the specified time after they were blocked, resulting in 108,201-
timeout. 208,224,301-
304,306,307,311
E307 <Reject Transport>Jam, note doesn't pass through During note transport, UEFS sensor did not become clear within J UT UEFS 001,002,010,103-
UEFS sensor. the specified time after it was blocked, resulting in timeout. 108,201-
208,224,301-
304,306,307,311
E308 <Reject Transport>Jam, note doesn't pass through During note transport, UERS sensor did not become clear within J UT UERS 001,002,010,103-
UERS sensor. the specified time after it was blocked, resulting in timeout. 108,201-
208,224,301-
304,306,307,311

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 37 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
E309 <Reject Transport>Jam, note doesn't pass through During note transport, UECS sensor did not become clear within J UT UECS 001,002,010,103-
UECS sensor. the specified time after it was blocked, resulting in timeout. 108,201-
208,224,301-
304,306,307,311
E30A <Transport before BV>Jam, note doesn't pass through During note transport, SSRS/SSLS/SSOS sensors did not become J SEP SSRS/SSLS/ 001,002,010,012,10
SSRS/SSLS/SSOS sensor. clear within the specified time after they were blocked, resulting in SSOS 3-108,201-206,301-
timeout. 304,306,307,311
E30B <Reject area>Reject area full is detected during note During note transport, UERS sensor did not become clear within J UT UERS 001,002,007,010,10
transport. (Jam, note doesn't pass through UERS the specified time after it was blocked, resulting in timeout, and 3-108,201-
sensor.) then URFC sensor was blocked. 208,224,225,227,30
1-307,311
E30C <Counterfeit area>Counterfeit area full is detected During note transport, UEFS sensor did not become clear within J UT UEFS 001,002,007,010,10
during note transport. (Jam, note doesn't pass through the specified time after it was blocked, resulting in timeout, and 3-108,201-
UEFS sensor.) then UFFC sensor was blocked. 208,224,225,227,30
1-307,311
E30D <Captured area>Captured area full is detected during During note transport, UECS sensor did not become clear within J UT UECS 001,002,007,010,10
note transport. (Jam, note doesn't pass through UECS the specified time after it was blocked, resulting in timeout, and 3-108,201-
sensor.) then UCFC sensor was blocked. 208,224,225,227,30
1-307,311
E30E <Cassette1 Transport>Jam, note doesn't pass through During note transport, CR1S/CL1S sensors did not become clear J CAS1 LT CR1S/CL1S 001,002,010,012,10
CR1S/CL1S sensor with compulsory storing. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout with compulsory storing. 226,301-304,306,
307,309,311
E30F <Cassette2 Transport>Jam, note doesn't pass through During note transport, CR2S/CL2S sensors did not become clear J CAS2 LT CR2S/CL2S 001,002,010,012,10
CR2S/CL2S sensor with compulsory storing. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout with compulsory storing. 226,301-304,306,
307,309,311
E310 <Cassette3 Transport>Jam, note doesn't pass through During note transport, CR3S/CL3S sensors did not become clear J CAS3 LT CR3S/CL3S 001,002,010,012,10
CR3S/CL3S sensor with compulsory storing. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout with compulsory storing. 226,301-304,306,
307,309,311
E311 <Cassette4 Transport>Jam, note doesn't pass through During note transport, CR4S/CL4S sensors did not become clear J CAS4 LT CR4S/CL4S 001,002,010,012,10
CR4S/CL4S sensor with compulsory storing. within the specified time after they were blocked, resulting in 3,107,108,203-209,
timeout. 226,301-304,306,
307,309,311
E4** Get transport data error.
E401 <Cassette1 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS1 013,307
about CR1S/CL1S sensor. CR1S/CL1S sensors.
E402 <Cassette2 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS2 013,307
about CR2S/CL2S sensor. CR2S/CL2S sensors.
E403 <Cassette3 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS3 013,307
about CR3S/CL3S sensor. CR3S/CL3S sensors.
E404 <Cassette4 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS4 013,307
about CR4S/CL4S sensor. CR4S/CL4S sensors.
E405 <Transport after BV>Error of getting transport data During note transport, could not get note transport data at UGAS J UT 013,307
about UGAS sensor. sensor.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 38 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
E406 <Escrow Transport>Error of getting transport data During note transport, could not get note transport data at J ESC 013,307
about ERRS/ERLS sensor. ERRS/ERLS sensors.
E407 <Escrow Transport>Error of getting transport data During note transport, could not get note transport data at J ESC 013,307
about EDRS/EDLS sensor. EDRS/EDLS sensors.
E408 <Reject Transport>Error of getting transport data about During note transport, could not get note transport data at UGDS J UT 013,307
UGDS sensor. sensor.
E409 <Reject Transport>Error of getting transport data about During note transport, could not get note transport data at UEFS J UT 013,307
UEFS sensor. sensor.
E40A <Reject Transport>Error of getting transport data about During note transport, could not get note transport data at UERS J UT 013,307
UERS sensor. sensor.
E40B <Reject Transport>Error of getting transport data about During note transport, could not get note transport data at UECS J UT 013,307
UECS sensor. sensor.
E40C <Cassettes Transport>Error of getting transport data During note transport, could not get note transport data at URHS J UT 013,307
about URHS sensor. sensor.
E40D <Transport before BV>Error of getting transport data During note transport, could not get note transport data at UFHS J UT 013,307
about UFHS sensor. sensor.
E40E <Cassette3 Transport>Error of getting transport data During note transport, could not get note transport data at LT3S J LT 013,307
about LT3S sensor. sensor.
E40F <BV Transport>Error of getting transport data about During note transport, could not get note transport data at BVIN J BV 013,307
BVIN sensor. sensor.
E410 <Separator Transport>Error of getting transport data During note transport, could not get note transport data at SDIS J SEP 013,307
about SDIS sensor. sensor.
E411 <Cassette1 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS1 013,307
about CR1S/CL1S sensor with compulsory storing. CR1S/CL1S sensors with compulsory storing.
E412 <Cassette2 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS2 013,307
about CR2S/CL2S sensor with compulsory storing. CR2S/CL2S sensors with compulsory storing.
E413 <Cassette3 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS3 013,307
about CR3S/CL3S sensor with compulsory storing. CR3S/CL3S sensors with compulsory storing.
E414 <Cassette4 Transport>Error of getting transport data During note transport, could not get note transport data at J CAS4 013,307
about CR4S/CL4S sensor with compulsory storing. CR4S/CL4S sensors with compulsory storing.
E480 <Transport after BV>Error of getting transport data During note transport, could not get note transport data of trailing J BV 013,307
about trailing edge. edge.
F1** Error of PCB communication.
F100 <PCB>Communication error between Upper PCB and RSTD (Communication error detect) bit was set at the start of a H or C UPCB and Cable UPCN 301,302,307
Lower PCB. mechanical operation command. LPCB
F2** Error of sensor level set
F210 <PCB>Error of sensor level set at upper PCB. During sensor level settings, Upper PCB DAC did not remove H UPCB 307
Busy signal even if waiting the specified time.
F211 <PCB>Error of sensor level set at lower PCB. During sensor level settings, Lower PCB DAC did not remove H LPCB 307
Busy signal even if waiting the specified time.
F3** Error of main tranport mortor
F300 <PCB>Error of main tranport motor. Transport DC motor did not reach the specified speed within the H UT UPCB UTMM 001,002,009,101-
specified time after activated. 108,301,302,307
F301 <PCB>Error of main tranport motor (FLT). An error signal detected during transport DC motor rotation. H UT UPCB UTMM 301,302,307,311
F4** <Over-current detection

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 39 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F400 <Over-current>Over-current detection at Pre-acceptor Overcurrent detected. This was caused because FL5VPA bit had H or C SPCB SEP(PT cover) SE7 PTHC,POLC, PABM, 302,307
5V line (FL5VPA) been set. PDPC,PRPC, PATM,
PCEC,PTPC, PACM
PBPC

F401 <Over-current>Over-current detection at Upper Base Overcurrent detected. This was caused because FL5VUB bit had H or C UPCB UB1,UB2 UULC,UCFC 302,307
5V line (FL5VUB) been set. ,URFC,UFFC
,UGAS,URH
S,UFHS,UG
DS,URLC,U
LPC,UECS,U
EFS,UERS,U
GLC
F402 <Over-current>Over-current detection at Escrow 5V Overcurrent detected. This was caused because FL5VES bit had H or C UPCB SE2 EECS,ETSS, 302,307
line (FL5VES) been set. EELS,EERS,
EDLS,EDRS,
ERLS,ERRS
F403 <Over-current>Over-current detection at Separator 5V Overcurrent detected. This was caused because FL5VSE bit had H or C UPCB SE1, PS1S,PS2S,P 302,307
line (FL5VSE) been set. S3S,PS4S,PT
CS,PASS,PD
SS,SDIS,SD
OS,SSLS,SS
RS,SSOS
F404 <Over-current>Over-current detection (FL5VRV) Overcurrent detected. This was caused because FL5VRV bit had H or C UPCB RV2S, PHPC,PLPC, 302,307
been set. RV2PH PDAC,ETRS
F405 <Over-current>Over-current detection at Separator 5V Overcurrent detected. This was caused because FL5VSE4 bit had H or C SPCB SE5,SE7, SPUC,SPPC, SEDM, 302,307
line (FL5VSE4) been set. SPWR SPBC,SSUC, SEPM,
SSLC,SSEC, SESM
SFIC,SFOC,S
PCC,SFPC,S
BLC,SCDC,S
HDC
F406 <Over-current>Over-current detection at Escrow 5V Overcurrent detected. This was caused because FL5VES4 bit had H or C SPCB ES1,ES3 ERUC,ERRC EESM, 302,307
line (FL5VES4) been set. ,ERLC,EVPC ERSM
,EELC,EERC
,EEUC,ECR
C,ECPC,EC
CC,ECHC
F408 <Over-current>Over-current detection at Separator 24V Overcurrent detected. This was caused because FL24VSE bit had H or C UPCB SE4,SPWR, SEFM, 302,307
line (FL24VSE) been set. (or SPCB) SE6,SPWR ESCM,
SEPM,
SESM,
SEDM,
SRMG

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 40 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F409 <Over-current>Over-current detection at Upper Base Overcurrent detected. This was caused because FL24VUB bit had H or C UPCB UB3, UAMG, 302,307
24V line (FL24VUB) been set. RV2MG UCMG,
UDMG,
UEMG,
R5MG,
R6MG,
DCM
F40A <Over-current>Over-current detection at Escrow 24V Overcurrent detected. This was caused because FL24VES bit had H or C SPCB SPWR,ES2 ERSM, 302,307
line (FL24VES) been set. EESM,
EBMG,
ESMG
F40B <Over-current>Over-current detection (FL24VRV) Overcurrent detected. This was caused because FL24VRV bit had H or C SPCB SPWR,PA1 PDMG, 302,307
been set. PHMG,
PABM,
PACM,
PATM,
PAMG
F410 <Over-current>Over-current detection at Lower Overcurrent detected. This was caused because FL5VLT bit had H or C LPCB LT1 LT3S,LFHS, 302,307
Transport 5V line (FL5VLT) been set. BLLC

F411 <Over-current>Over-current detection at Shutter 5V Overcurrent detected. This was caused because FL5VSH bit had H or C LPCB SHT2 SHOC,SHCC 302,307
line (FL5VSH) been set.
F412 <Over-current>Over-current detection (FL5VEX) Overcurrent detected. This was caused because FL5VEX bit had H or C LPCB (EXT) 302,307
been set.
F413 <Over-current>Over-current detection (FL5VRV) Overcurrent detected. This was caused because FL5VRV bit had H or C LPCB (RV1PH) 302,307
been set. (RSVS)
F414 <Over-current>Over-current detection at Cassette Overcurrent detected. This was caused because FL5VCS1 bit had H or C LPCB CS1 302,307
Position 1 5V line (FL5VCS1) been set.
F415 <Over-current>Over-current detection at Cassette Overcurrent detected. This was caused because FL5VCS2 bit had H or C LPCB CS2 302,307
Position 2 5V line (FL5VCS2) been set.
F416 <Over-current>Over-current detection at Cassette Overcurrent detected. This was caused because FL5VCS3 bit had H or C LPCB CS3 302,307
Position 3 5V line (FL5VCS3) been set.
F417 <Over-current>Over-current detection at Cassette Overcurrent detected. This was caused because FL5VCS4 bit had H or C LPCB CS4 302,307
Position 4 5V line (FL5VCS4) been set.
F418 <Over-current>Over-current detection at Lower Base Overcurrent detected. This was caused because FL24VLB1 bit had H or C LPCB LB1 BS1M, 302,307
24V line (FL24VLB1) been set. BF1M,
BS2M,
BF2M
F419 <Over-current>Over-current detection at Lower Base Overcurrent detected. This was caused because FL24VLB2 bit had H or C LPCB LB3,LB4 BS3M, 302,307
24V line (FL24VLB2) been set. BF3M,
BS4M,
BF4M
F41A <Over-current>Over-current detection at Lower Overcurrent detected. This was caused because FL24VLT bit had H or C LPCB LT1 L1MG, 302,307
Transport 24V line (FL24VLT) been set. L2MG,
L3MG,
L4MG

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 41 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F41B <Over-current>Over-current detection at Cassette 24V Overcurrent detected. This was caused because FL24VCS bit had H or C LPCB CS1,CS2, C1MG, 302,307
line (FL24VCS) been set. CS3,CS4 C2MG,
C3MG,
C4MG
F41C <Over-current>Over-current detection (FL24VEX) Overcurrent detected. This was caused because FL24VEX bit had H or C LPCB (EXT) 302,307
been set.
F41D <Over-current>Over-current detection at Shutter 24V Overcurrent detected. This was caused because FL24VSH bit had H or C LPCB SHT2 302,307
line (FL24VSH) been set.
F4FF <Over-current>Over-current detection at unfixed place Overcurrent detected. But the location of overcurrent was not set. H or C LPCB 302,307
F5** Notes remain in module After clearing jam by hands, it should be reset (jam clear command :JA or MJ) with SW because GBxx FW memorizes error information.
F500 <Separator Transport>Notes remains between Media remaining data between SSRS/SSLS/SSOS and SDIS S Reset with SW SEP remaining SE1 001,002,103-
SSRS/SSLS/SSOS sensor and SDIS sensor and on the sensors memorized by software had been set when a command or note checking 108,201-206
outskirts of it. note transport started. or UPCB
F501 <Transport after BV>Notes remains between BVIN Media remaining data between BVIN and UGAS sensors S Reset with SW BV and UT BV LAN 001,002,011,103-
sensor and UGAS sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note UB1 108,201-206
transport started. checking
or UPCB
F502 <Escrow Transport>Notes remains between UGAS Media remaining data between UGAS and EDRS/EDLS sensors S Reset with SW UT and ESC SE2,UB1 001,002,103-
sensor and EDxS sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note 108,201-208
transport started. checking
or UPCB
F503 <Escrow Transport>Notes remains between UGAS Media remaining data between UGAS and ERRS/ERLS sensors S Reset with SW UT and ESC SE2,UB1 001,002,103-
sensor and ERxS sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note 108,201-208
transport started. checking
or UPCB
F504 <Transport after BV>Notes remains between UGAS Media remaining data between UGAS and UGDS sensors S Reset with SW UT remaining UB1 001,002,103-
sensor and UGDS sensor and on the outskirts of it. memorized by software had been set when a command or note note checking 108,201-208
transport started. or UPCB
F505 <Cassettes Transport>Notes remains between UGAS Media remaining data between UGAS and URHS sensors S Reset with SW UT remaining UB1 001,002,103-
sensor and URHS sensor and on the outskirts of it. memorized by software had been set when a command or note note checking 108,201-208
transport started. or UPCB
F506 <Reject Transport>Notes remains between UGDS Media remaining data between UGDS and UECS sensors S Reset with SW UT remaining UB1,UB2 001,002,103-
sensor and UECS sensor and on the outskirts of it. memorized by software had been set when a command or note note checking 108,201-208
transport started. or UPCB
F507 <Reject Transport>Notes remains between UGDS Media remaining data between UGDS and UERS sensors S Reset with SW UT remaining UB1,UB2 001,002,103-
sensor and UERS sensor and on the outskirts of it. memorized by software had been set when a command or note note checking 108,201-208
transport started. or UPCB
F508 <Reject Transport>Notes remains between UGDS Media remaining data between UGDS and UEFS sensors S Reset with SW UT remaining UB1.UB2 001,002,103-
sensor and UEFS sensor and on the outskirts of it. memorized by software had been set when a command or note note checking 108,201-208
transport started. or UPCB
F509 <Cassette1 Transport>Notes remains between URHS Media remaining data between URHS and CR1S/CL1S sensors S Reset with SW UT, LT and UB1 001,002,009,103-
sensor and Cx1S sensor and on the outskirts of it. memorized by software had been set when a command or note CAS remaining CS1 108,201-208
transport started. note checking
or UPCB

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 42 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F50A <Cassette2 Transport>Notes remains between URHS Media remaining data between URHS and CR2S/CL2S sensors S Reset with SW UT, LT and UB1 001,002,009,103-
sensor and Cx2S sensor and on the outskirts of it. memorized by software had been set when a command or note CAS remaining CS2 108,201-208
transport started. note checking
or UPCB
F50B <Cassette2 Transport>Notes remains between URHS Media remaining data between URHS and LT3S sensors S Reset with SW UT and LT UB1 001,002,009,103-
sensor and LT3S sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note LT1 108,201-208
transport started. checking
or UPCB
F50C <Cassette3 Transport>Notes remains between LT3S Media remaining data between LT3S and CR3S/CL3S sensors S Reset with SW LT and CAS LT1 001,002,103-
sensor and Cx3S sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note CS3 108,201-208
transport started. checking
or UPCB
F50D <Cassette4 Transport>Notes remains between LT3S Media remaining data between LT3S and CR4S/CL4S sensors S Reset with SW LT and CAS LT1 001,002,103-
sensor and Cx4S sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note CS４ 108,201-208
transport started. checking
or UPCB
F50E <Cassette4 Transport>Notes remains between LT3S Media remaining data between LT3S and UFHS sensors S Reset with SW LT and UT LT1 001,002,009,103-
sensor and UFHS sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note UB1 108,201-208
transport started. checking
or UPCB
F50F <Transport before BV>Notes remains between UFHS Media remaining data between UFHS and BVIN sensors S Reset with SW BVE and BV UB1 001,002,009,103-
sensor and BVIN sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note BV LAN 108,201-208
transport started. checking
or UPCB
F510 <Cassette1 Transport>Notes remains between Cx1S Media remaining data between CR1S/CL1S and UFHS sensors S Reset with SW CAS1, LT and CS1 001,002,009,103-
sensor and UFHS sensor and on the outskirts of it. memorized by software had been set when a command or note UT remaining UB1 108,201-208
transport started. note checking
or UPCB
F511 <Cassette2 Transport>Notes remains between Cx2S Media remaining data between CR2S/CL2S and UFHS sensors S Reset with SW CAS2, LT and CS2 001,002,009,103-
sensor and UFHS sensor and on the outskirts of it. memorized by software had been set when a command or note UT remaining UB1 108,201-208
transport started. note checking
or UPCB
F512 <Cassette3 Transport>Notes remains between Cx3S Media remaining data between CR3S/CL3S and UFHS sensors S Reset with SW CAS3, LT and CS3 001,002,009,103-
sensor and UFHS sensor and on the outskirts of it. memorized by software had been set when a command or note UT remaining UB1 108,201-208
transport started. note checking
or UPCB
F513 <Cassette4 Transport>Notes remains between Cx4S Media remaining data between CR4S/CL4S and UFHS sensors S Reset with SW CAS4, LT and CS4 001,002,009,103-
sensor and UFHS sensor and on the outskirts of it. memorized by software had been set when a command or note UT remaining UB1 108,201-208
transport started. note checking
or UPCB
F514 <Separator Transport>Notes remains on Media remaining data of SSRS/SSLS/SSOS sensors memorized by S Reset with SW SEP remaining SE1 001,002,010,012,10
SSRS/SSLS/SSOS sensor. software when a command or note transport started. note checking 3-108,203-206,301-
or UPCB 307
F515 <Transport after BV>Notes remains on UGAS sensor. Media remaining data of UGAS sensor memorized by software S Reset with SW UT remaining UB1 001,002,010,103-
when a command or note transport started. note checking 108,201-208,301-
or UPCB 307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 43 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F516 <Reject Transport>Notes remains on UGDS sensor. Media remaining data of UGDS sensor memorized by software S Reset with SW UT remaining UB1 001,002,010,103-
when a command or note transport started. note checking 108,201-208,301-
or UPCB 307
F517 <Escrow Transport>Notes remains on EDxS sensor. Media remaining data of EDRS/EDLS sensors memorized by S Reset with SW ESC remaining SE2 001,002,010,103-
software when a command or note transport started. note checking 108,201-208,301-
or UPCB 307
F518 <Escrow Transport>Notes remains on ERxS sensor. Media remaining data of ERRS/ERLS sensors memorized by S Reset with SW ESC remaining SE2 001,002,010,103-
software when a command or note transport started. note checking 108,201-208,301-
or UPCB 307
F519 <Reject Transport>Notes remains on UECS sensor. Media remaining data of UECS sensor memorized by software S Reset with SW UT remaining UB2 001,002,010,103-
when a command or note transport started. note checking 108,201-208,301-
or UPCB 307
F51A <Reject Transport>Notes remains on UERS sensor. Media remaining data of UERS sensor memorized by software S Reset with SW UT remaining UB2 001,002,010,103-
when a command or note transport started. note checking 108,201-208,301-
or UPCB 307
F51B <Reject Transport>Notes remains on UEFS sensor. Media remaining data of UEFS sensor memorized by software S Reset with SW UT remaining UB2 001,002,010,103-
when a command or note transport started. note checking 108,201-208,301-
or UPCB 307
F51C <Cassettes Transport>Notes remains on URHS sensor. Media remaining data of URHS sensor memorized by software S Reset with SW UT remaining UB1 001,002,009,010,10
when a command or note transport started. note checking 3-108,201-208,301-
or UPCB 307
F51D <Transport before BV>Notes remains on UFHS sensor. Media remaining data of UFHS sensor memorized by software S Reset with SW UT remaining UB1 001,002,009,010,10
when a command or note transport started. note checking 3-108,201-208,301-
or UPCB 307
F51E <Transport before BV>Notes remains on LFHS sensor. Media remaining data of LFHS sensor memorized by software S Reset with SW LT remaining LT1 001,002,009,010,10
when a command or note transport started. note checking 3-108,201-208,301-
or LPCB 307
F51F <Cassette3 Transport>Notes remains on LT3S sensor. Media remaining data of LT3S sensor memorized by software S Reset with SW LT remaining LT1 001,002,010,103-
when a command or note transport started. note checking 108,201-208,301-
or LPCB 307
F520 <Cassette1 Transport>Notes remains on Cx1S sensor. Media remaining data of CR1S/CL1S sensors memorized by S Reset with SW CAS1 remaining CS1 001,002,010,103-
software when a command or note transport started. note checking 108,203-
or LPCB 209,226,301-307
F521 <Cassette2 Transport>Notes remains on Cx2S sensor. Media remaining data of CR2S/CL2S sensors memorized by S Reset with SW CAS2 remaining CS2 001,002,010,103-
software when a command or note transport started. note checking 108,203-
or LPCB 209,226,301-307
F522 <Cassette3 Transport>Notes remains on Cx3S sensor. Media remaining data of CR3S/CL3S sensors memorized by S Reset with SW CAS3 remaining CS3 001,002,010,103-
software when a command or note transport started. note checking 108,203-
or LPCB 209,226,301-307
F523 <Cassette4 Transport>Notes remains on Cx4S sensor. Media remaining data of CR4S/CL4S sensors memorized by S Reset with SW CAS4 remaining CS4 001,002,010,103-
software when a command or note transport started. note checking 108,203-
or LPCB 209,226,301-307
F524 <Cassette2 Transport>Notes remains between Cx1S Media remaining data between CR1S/CL1S and CR2S/CL2S S Reset with SW CAS1 and CS1,CS2 001,002,010,103-
sensor and Cx2S sensor and on the outskirts of it. sensors memorized by software had been set when a command or CAS2 108,201-208,301-
note transport started. remaining note 307
checking

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 44 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F525 <Cassette4 Transport>Notes remains between Cx3S Media remaining data between CR3S/CL3S and CR4S/CL4S S Reset with SW CAS3 and CS3,CS4 001,002,010,103-
sensor and Cx4S sensor and on the outskirts of it. sensors memorized by software had been set when a command or CAS4 108,201-208,301-
note transport started. remaining note 307
checking
F526 <Cassette2 Transport>Notes remains between Cx1S Media remaining data between CR1S/CL1S and LT3S sensors S Reset with SW CAS1 and LT CS1,LT1 001,002,010,103-
sensor and LT3S sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note 108,201-208,301-
transport started. checking 307
or LPCB
F527 <Cassette2 Transport>Notes remains between Cx2S Media remaining data between CR2S/CL2S and LT3S sensors S Reset with SW CAS2 and LT CS2,LT1 001,002,010,103-
sensor and LT3S sensor and on the outskirts of it. memorized by software had been set when a command or note remaining note 108,201-208,301-
transport started. checking 307
or LPCB
F528 <BV>Notes remains on BVIN sensor. Media remaining data of BVIN sensor memorized by software S Reset with SW BV remaining BV LAN 001,002,010,011,10
when a command or note transport started. note checking 3-108,203-
or UPCB 206,224,301-307
F529 <BV>Notes remains on BVOUT sensor. Media remaining data of BVOUT sensor memorized by software S Reset with SW BV remaining BV LAN 001,002,010,011,10
when a command or note transport started. note checking 3-108,203-
or UPCB 206,224,301-307
F52A <Separator Transport>Notes remains between SDIS Media remaining data between SDIS and BVIN sensors S Reset with SW SEP, BVE and SE1 001,002,010,103-
sensor and BVIN sensor and on the outskirts of it. memorized by software had been set when a command or note BV remaining BV LAN 108,201-
transport started. note checking 206,223,224,301-
or UPCB 307
F52B <Separator Transport>Notes remains on SDIS sensor. Media remaining data of SDIS sensor memorized by software S Reset with SW SEP remaining SE1 001,002,010,103-
when a command or note transport started. note checking 108,201-
or UPCB 206,222,301-307
F6** Notes remain in module
F601 <Separator Transport>Notes remains at SSRS/SSLS/SSOS sensors had been blocked when a command or J or C SEP remaining UPCB SE1 001,002,010,012,10
SSRS/SSLS/SSOS sensor. note transport started. note checking 3-108,203-206,301-
SSRS/SSLS/SSOS sensors were blocked after transport rotation by 307
MR comamnd.
SSRS/SSLS/SSOS sensors were still blocked after jam clear
processing by JA and MJ commands.
F602 <Separator Transport>Notes remain at SDIS sensor. SDIS sensor had been blocked when a command or note transport J or C SEP remaining UPCB SE1 001,002,010,103-
started. note checking 108,201-
SDIS sensor was blocked after transport path rotation by MR 206,222,301-307
comamnd.
SDIS sensor was still blocked after jam clear processing by JA and
MJ commands.
F603 <Separator Transport>Notes remains at SDOS sensor. SDOS sensor had been blocked when a command or note transport J or C SEP remaining UPCB SE1 001,002,010,103-
started. note checking 108,201-
SDOS sensor was blocked after transport path rotation by MR 206,222,223,,301-
comamnd. 307
F604 <Transport before BV>Notes remains at UFHS sensor. UFHS sensor had been blocked when a command or note transport J or C UT remaining LT remaining UB1 001,002,009,010,10
started. note checking note checking or 3-108,201-208,301-
UFHS sensor was blocked after transport path rotation by MR UPCB 307
comamnd.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 45 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F605 <Cassettes Transport>Notes remains at URHS sensor. URHS sensor had been blocked when a command or note J or C UT remaining LT remaining UB1 001,002,009,010,10
transport started. note checking note checking or 3-108,201-208,301-
URHS sensor was blocked after transport path rotation by MR UPCB 307
comamnd.
F606 <Transport after BV>Notes remains at UGAS sensor. UGAS sensor had been blocked when a command or note J or C UT remaining BV remaining UB1 001,002,010,103-
transport started. note checking note checking 108,201-208,301-
UGAS sensor was blocked after transport path rotation by MR or UPCＢ 307
comamnd.
F607 <Escrow Transport>Notes remains at EDRS/EDLS EDRS/EDLS sensors had been blocked when a command or note J or C ESC remaining UT remaining SE2 001,002,010,103-
sensor. transport started. note checking note checking 108,201-208,301-
EDRS/EDLS sensors were blocked after transport path rotation by or UPCＢ 307
MR comamnd.
F608 <Escrow Transport>Notes remains at ERRS/ERLS ERRS/ERLS sensors had been blocked when a command or note J or C ESC remaining UT remaining SE2 001,002,010,103-
sensor. transport started. note checking note checking 108,201-208,301-
ERRS/ERLS sensors were blocked after transport path rotation by or UPCＢ 307
MR comamnd.
F609 <Reject Transport>Notes remains at UGDS sensor. UGDS sensor had been blocked when a command or note J or C UT remaining UPCＢ UB1 001,002,010,103-
transport started. note checking 108,201-208,301-
UGDS sensor was blocked after transport path rotation by MR 307
comamnd.
F60A <Reject Transport>Notes remains at UEFS sensor. UEFS sensor had been blocked when a command or note transport J or C UT remaining RJ Bin UB2 001,002,010,103-
started. note checking remaining note 108,201-208,301-
UEFS sensor was blocked after transport path rotation by MR checking 307
comamnd.
F60B <Reject Transport>Notes remains at UERS sensor. UERS sensor had been blocked when a command or note transport J or C UT remaining RJ Bin UB2 001,002,010,103-
started. note checking remaining note 108,201-208,301-
UERS sensor was blocked after transport path rotation by MR checking 307
comamnd.
F60C <Reject Transport>Notes remains at UECS sensor. UECS sensor had been blocked when a command or note transport J or C UT remaining RJ Bin UB2 001,002,010,103-
started. note checking remaining note 108,201-208,301-
UECS sensor was blocked after transport path rotation by MR checking 307
comamnd.
F60D <Cassette1 Transport>Notes remains at CR1S/CL1S CR1S/CL1S sensors had been blocked when a command or note J or C CAS1 remaining LT remaining CS1 001,002,010,103-
sensor. transport started. note checking note checking 108,201-208,301-
CR1S/CL1S sensors were blocked after transport path rotation by or LPCＢ 307
MR comamnd.
F60E <Cassette2 Transport>Notes remains at CR2S/CL2S CR2S/CL2S sensors had been blocked when a command or note J or C CAS2 remaining LT remaining CS2 001,002,010,103-
sensor. transport started. note checking note checking 108,201-208,301-
CR2S/CL2S sensors were blocked after transport path rotation by or LPCＢ 307
MR comamnd.
F60F <Cassette3 Transport>Notes remains at CR3S/CL3S CR3S/CL3S sensors had been blocked when a command or note J or C CAS3 remaining LT remaining CS3 001,002,010,103-
sensor. transport started. note checking note checking 108,201-208,301-
CR3S/CL3S sensors were blocked after transport path rotation by or LPCＢ 307
MR comamnd.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 46 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F610 <Cassette4 Transport>Notes remains at CR4S/CL4S CR4S/CL4S sensors had been blocked when a command or note J or C CAS4 remaining LT remaining CS4 001,002,010,103-
sensor. transport started. note checking note checking 108,201-208,301-
CR4S/CL4S sensors were blocked after transport path rotation by or LPCＢ 307
MR comamnd.
F611 <Cassette3 Transport>Notes remains at LT3S sensor. LT3S sensor had been blocked when a command or note transport J or C LT remaining LPCＢ LT1 001,002,010,103-
started. note checking 108,201-208,301-
LT3S sensor was blocked after transport path rotation by MR 307
comamnd.
LT3S sensor was still blocked after jam clear processing by JA and
MJ commands.
F612 <Transport before BV>Notes remains at LFHS sensor. LFHS sensor had been blocked when a command or note transport J or C LT remaining LPCＢ LT1 001,002,009,010,10
started. note checking 3-108,201-208,301-
LFHS sensor was blocked after transport path rotation by MR 307
comamnd.
F620 <Bunch Transport>Notes remains at EELS sensor. EELS sensor was blocked during MR command. J or C ESC remaining UPCB SE2 001,002,010,103-
note checking 108,110,210-
213,301-307
F621 <Bunch Transport>Notes remains at EERS sensor. EERS sensor was blocked during MR command. J or C ESC remaining UPCB SE2 001,002,010,103-
note checking 108,110,210-
213,301-307
F624 <Pre-Acceptor>Notes remains at PTCS sensor. PTCS sensor was blocked during MR command. J or C PAC remaining UPCB SE1 001,002,010,103-
note checking 108,201,202,205,20
6,214-218,220,301-
307

F625 <Pre-Acceptor>Notes remains at PS1S sensor. PS1S sensor was blocked during MR command. J or C PAC remaining UPCB SE1 001,002,010,103-
note checking 108,116,201-206,
214-220,301-307
F626 <Pre-Acceptor>Notes remains at PS2S sensor. PS2S sensor was blocked during MR command. J or C PAC remaining UPCB SE1 001,002,010,103-
note checking 108,116,201-206,
214-220,301-307
F627 <Pre-Acceptor>Notes remains at PS3S sensor. PS3S sensor was blocked during MR command. J or C PAC remaining UPCB SE1 001,002,010,103-
note checking 108,116,201-206,
214-220,301-307
F628 <Pre-Acceptor>Notes remains at PS4S sensor. PS4S sensor was blocked during MR command. J or C PAC remaining UPCB SE1 001,002,010,103-
note checking 108,116,201-206,
214-220,301-307
F629 <Bunch Transport>Notes remains at Bunch transport. EERS/EELS sensors were blocked. J or C ESC remaining PAC or SEP SE1 001,002,010,103-
Media remaining data of Top transport memorized by software had note checking remaining note 108,116,201-206,
been set when a command or note transport started. checking 214-221,301-307
or UPCB
F631 <Separator Transport>Notes stay at SSRS/SSLS/SSOS During jam clear processing, SSRS/SSLS/SSOS sensors did not J or C SEP remaining UPCB SE1 001,002,010,012,10
sensor become clear within the specified time. note checking 3-108,203-206,301-
307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 47 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F632 <Separator Transport>Notes stay at SDIS sensor During jam clear processing, SDIS sensor did not become clear J or C SEP remaining UPCB SE1 001,002,010,103-
within the specified time. note checking 108,201-
206,222,301-307
F633 <Separator Transport>Notes stay at SDOS sensor During jam clear processing, SDOS sensor did not become clear J or C SEP remaining UPCB SE1 001,002,010,103-
within the specified time. note checking 108,201-
206,222,223,,301-
307
F634 <Transport before BV>Notes stay at UFHS sensor During jam clear processing, UFHS sensor did not become clear J or C UT remaining LT remaining UB1 001,002,009,010,10
within the specified time. note checking note checking 3-108,201-208,301-
or UPCＢ 307
F635 <Cassettes Transport>Notes stay at URHS sensor During jam clear processing, URHS sensor did not become clear J or C UT remaining LT remaining UB1 001,002,009,010,10
within the specified time. note checking note checking 3-108,201-208,301-
or UPCＢ 307
F636 <Transport after BV>Notes stay at UGAS sensor During jam clear processing, UGAS sensor did not become clear J or C UT remaining UPCB UB1 001,002,010,103-
within the specified time. note checking 108,201-208,301-
307

F637 <Escrow Transport>Notes stay at EDRS/EDLS sensor During jam clear processing, EDRS/EDLS sensors did not become J or C ESC remaining UT remaining SE2 001,002,010,103-
clear within the specified time. note checking note checking 108,201-208,301-
or UPCB 307
F638 <Escrow Transport>Notes stay at ERRS/ERLS sensor During jam clear processing, ERRS/ERLS sensors did not become J or C ESC remaining UT remaining SE2 001,002,010,103-
clear within the specified time. note checking note checking 108,201-208,301-
or UPCB 307
F639 <Reject Transport>Notes stay at UGDS sensor During jam clear processing, UGDS sensor did not become clear J or C UT remaining UPCB UB1 001,002,010,103-
within the specified time. note checking 108,201-208,301-
307

F63A <Reject Transport>Notes stay at UEFS sensor During jam clear processing, UEFS sensor did not become clear J or C UT remaining RJ Bin UB2 001,002,010,103-
within the specified time. note checking remaining note 108,201-208,301-
checking 307
F63B <Reject Transport>Notes stay at UERS sensor During jam clear processing, UERS sensor did not become clear J or C UT remaining RJ Bin UB2 001,002,010,103-
within the specified time. note checking remaining note 108,201-208,301-
checking 307
F63C <Reject Transport>Notes stay at UECS sensor During jam clear processing, UECS sensor did not become clear J or C UT remaining RJ Bin UB2 001,002,010,103-
within the specified time. note checking remaining note 108,201-208,301-
checking 307
F63D <Cassette1 Transport>Notes stay at CR1S/CL1S sensor During jam clear processing, CR1S/CL1S sensors did not become J or C CAS1 remaining LT remaining CS1 001,002,010,103-
clear within the specified time. note checking note checking UPCN 108,201-208,301-
or LPCＢ 307
F63E <CAssette2 Transport>Notes stay at CR2S/CL2S During jam clear processing, CR2S/CL2S sensors did not become J or C CAS2 remaining LT remaining CS2 001,002,010,103-
sensor clear within the specified time. note checking note checking UPCN 108,201-208,301-
or LPCＢ 307
F63F <Cassette3 Transport>Notes stay at CR3S/CL3S sensor During jam clear processing, CR3S/CL3S sensors did not become J or C CAS3 remaining LT remaining CS3 001,002,010,103-
clear within the specified time. note checking note checking UPCN 108,201-208,301-
or LPCＢ 307

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 48 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F640 <CAssette4 Transport>Notes stay at CR4S/CL4S During jam clear processing, CR4S/CL4S sensors did not become J or C CAS4 remaining LT remaining CS4 001,002,010,103-
sensor clear within the specified time. note checking note checking UPCN 108,201-208,301-
or LPCＢ 307
F641 <Cassette3 Transport>Notes stay at LT3S sensor During jam clear processing, LT3S sensor did not become clear J or C LT remaining LPCＢ LT1 001,002,010,103-
within the specified time. note checking 108,201-208,301-
307

F64B <Transport before BV>Notes stay at LFHS sensor During jam clear processing, LFHS sensor did not become clear J or C LT remaining LPCＢ LT1 001,002,009,010,10
within the specified time. note checking 3-108,201-208,301-
307
F64C <BV>Notes stay in BV During jam clear processing, BVIN sensor did not become clear J or C BV remaining UPCＢ BV LAN 001,002,010,103-
within the specified time. note checking 108,201-
206,224,301-307
F64D <BV>Notes stay in BV During jam clear processing, BVOUT sensor did not become clear J or C BV remaining UPCＢ BV LAN 001,002,010,103-
within the specified time. note checking 108,201-
206,224,301-307
F64E <Cassette1 Transport>Notes stay at CR1S/CL1S sensor During jam clear processing, CR1S/CL1S sensors did not become J or C CAS1 remaining LT remaining CS1 001,002,010,103-
with compulsory storing clear within the specified time with compulsory storing. note checking note checking 108,201-208,301-
or LPCＢ 307
F64F <CAssette2 Transport>Notes stay at CR2S/CL2S During jam clear processing, CR2S/CL2S sensors did not become J or C CAS2 remaining LT remaining CS2 001,002,010,103-
sensor with compulsory storing clear within the specified time with compulsory storing. note checking note checking 108,201-208,301-
or LPCＢ 307
F650 <Cassette3 Transport>Notes stay at CR3S/CL3S sensor During jam clear processing, CR3S/CL3S sensors did not become J or C CAS3 remaining LT remaining CS3 001,002,010,103-
with compulsory storing clear within the specified time with compulsory storing. note checking note checking 108,201-208,301-
or LPCＢ 307
F651 <CAssette4 Transport>Notes stay at CR4S/CL4S During jam clear processing, CR4S/CL4S sensors did not become J or C CAS4 remaining LT remaining CS4 001,002,010,103-
sensor with compulsory storing clear within the specified time with compulsory storing. note checking note checking 108,201-208,301-
or LPCＢ 307
F7** Illegal Sensor Error
F700 <Separator Transport>Illegal sensor detect Illegal change of SSRS/SSLS/SSOS sensors detected during H SEP SSRS/SSLS/ 001,002,301-
SSRS/SSLS/SSOS command processing. SSOS 307,311
F701 <Transport after BV>Illegal sensor detect UGAS Illegal change of UGAS sensor detected during command H UT UGAS 001,002,301-
processing. 307,311

F702 <Reject Transport>Illegal sensor detect UGDS Illegal change of UGDS sensor detected during command H UT UGDS 001,002,301-
processing. 307,311

F703 <Escrow Transport>Illegal sensor detect EDRS/EDLS Illegal change of EDRS/EDLS sensors detected during command H ESC EDRS/EDLS 001,002,301-
processing. 307,311
F704 <Escrow Transport>Illegal sensor detect ERRS/ERLS Illegal change of ERRS/ERLS sensors detected during command H ESC ERRS/ERLS 001,002,301-
processing. 307,311
F705 <Reject Transport>Illegal sensor detect UECS Illegal change of UECS sensor detected during command H UT UECS 001,002,301-
processing. 307,311
F706 <Reject Transport>Illegal sensor detect UERS Illegal change of UERS sensor detected during command H UT UERS 001,002,301-
processing. 307,311

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 49 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F707 <Reject Transport>Illegal sensor detect UEFS Illegal change of UEFS sensor detected during command H UT UEFS 001,002,301-
processing. 307,311
F708 <Cassettes Transport>Illegal sensor detect URHS Illegal change of URHS sensor detected during command H UT URHS 001,002,301-
processing. 307,311

F709 <Transport before BV>Illegal sensor detect UFHS Illegal change of UFHS sensor detected during command H UT UFHS 001,002,301-
processing. 307,311

F70A <Cassette3 Transport>Illegal sensor detect LT3S Illegal change of LT3S sensor detected during command H LT LT3S 001,002,301-
processing. 307,311
F70B <Cassette1 Transport>Illegal sensor detect CR1S/CL1S Illegal change of CR1S/CL1S sensors detected during command H CAS1 CR1S/CL1S 001,002,301-
processing. 307,311
F70C <Cassette2 Transport>Illegal sensor detect CR2S/CL2S Illegal change of CR2S/CL2S sensors detected during command H CAS2 CR2S/CL2S 001,002,301-
processing. 307,311
F70D <Cassette3 Transport>Illegal sensor detect CR3S/CL3S Illegal change of CR3S/CL3S sensors detected during command H CAS3 CR3S/CL3S 001,002,301-
processing. 307,311
F70E <Cassette4 Transport>Illegal sensor detect CR4S/CL4S Illegal change of CR4S/CL4S sensors detected during command H CAS4 CR4S/CL4S 001,002,301-
processing. 307,311
F70F <Transport before BV>Illegal sensor detect LFHS Illegal change of LFHS sensor detected during command H LT LFHS 001,002,301-
processing. 307,311
F710 <Upper Unit>Upper unit come off during processing Illegal change of UULC sensor detected during command H UT UULC 001,002,301-
processing. 307,311

F711 <Lower Unit>Lower unit come off during processing Illegal change of ULPC sensor detected during command H UT LT or Cradle ULPC 001,002,301-
processing. 307,311

F712 <Reject bin>Reject bin come off during processing Illegal change of URLC sensor detected during command H UT URLC 001,002,301-
processing. 307,311

F713 <Lower Transport>Lower transport come off during Illegal change of BLLC sensor detected during command H LT BLLC 001,002,301-
processing processing. 307,311
F714 <BV>Illegal sensor detect in BV Illegal change of BVIN sensor detected during command H BV BVIN 001,002,301-
processing. 307,311
F715 <BV>Illegal sensor detect in BV Illegal change of BVOUT sensor detected during command H BV BVOUT 001,002,301-
processing. 307,311
F716 <Shutter>Illegal sensor detect SHCC Illegal change of SHCC sensor detected during command H SHT SHCC 001,002,301-
processing. 307,311

F717 <Transport before BV>Transport before BV come off Illegal change of SBLC sensor detected during command H SEP SBLC 001,002,301-
during processing processing. 307,311
F718 <Transport under Reject bin>Transport under Reject Illegal change of UGLC sensor detected during command H UT UGLC 001,002,301-
bin come off during processing processing. 307,311

F719 <Top Transport>Top transport come off during Illegal change of ETLC sensor detected during command H ESC ETLC 001,002,301-
processing processing. 307,311

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 50 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
F71A <Interlock>Interlock come off during processing Illegal change of ILOF sensor detected during command H LB ILOF 001,002,301-
processing. 307,311
F71B <Pre-Acceptor>Illegal sensor detect PS1S Illegal change of PS1S sensor detected during command H PAC PS1S 001,002,301-
processing. 307,311
F71C <Pre-Acceptor>Illegal sensor detect PS2S Illegal change of PS2S sensor detected during command H PAC PS2S 001,002,301-
processing. 307,311
F71D <Pre-Acceptor>Illegal sensor detect PS3S Illegal change of PS3S sensor detected during command H PAC PS3S 001,002,301-
processing. 307,311
F71E <Pre-Acceptor>Illegal sensor detect PS4S Illegal change of PS4S sensor detected during command H PAC PS4S 001,002,301-
processing. 307,311
F71F <Pre-Acceptor>Illegal sensor detect PTCS Illegal change of PTCS sensor detected during command H PAC PTCS 001,002,301-
processing. 307,311
F720 <Pre-Acceptor Transport>Illegal sensor detect PASS Illegal change of PASS sensor detected during command H PAC PASS 001,002,301-
processing. 307,311
F721 <Pre-Acceptor Transport>Illegal sensor detect PDSS Illegal change of PDSS sensor detected during command H PAC PDSS 001,002,301-
processing. 307,311
F722 <Bunch Transport>Illegal sensor detect EERS Illegal change of EERS sensor detected during command H ESC EERS 001,002,301-
processing. 307,311
F723 <Bunch Transport>Illegal sensor detect EELS Illegal change of EELS sensor detected during command H ESC EELS 001,002,301-
processing. 307,311
F724 <Bunch Transport>Illegal sensor detect EECS Illegal change of EECS sensor detected during command H ESC EECS 001,002,301-
processing. 307,311
F725 <Pre-Acceptor Transport>Illegal sensor detect PTPC Illegal change of PTPC sensor detected during command H PAC PTPC 001,002,301-
processing. 307,311
F726 <Pre-Acceptor Transport>Illegal sensor detect PBPC Illegal change of PBPC sensor detected during command H PAC PBPC 001,002,301-
processing. 307,311
F727 <Cassette1 Transport>Illegal sensor detect CR1S/CL1S Illegal change of CR1S/CL1S sensors detected during command H CAS1 CR1S/CL1S 001,002,301-
with compulsory storing processing. 307,311
F728 <Cassette2 Transport>Illegal sensor detect CR2S/CL2S Illegal change of CR2S/CL2S sensors detected during command H CAS2 CR2S/CL2S 001,002,301-
with compulsory storing processing with compulsory storing. 307,311
F729 <Cassette3 Transport>Illegal sensor detect CR3S/CL3S Illegal change of CR3S/CL3S sensors detected during command H CAS3 CR3S/CL3S 001,002,301-
with compulsory storing processing with compulsory storing. 307,311
F72A <Cassette4 Transport>Illegal sensor detect CR4S/CL4S Illegal change of CR4S/CL4S sensors detected during command H CAS4 CR4S/CL4S 001,002,301-
with compulsory storing processing with compulsory storing. 307,311
FF** Over max light sensor level
FF00 <Pre-Acceptor>Over max light PS1S sensor At the time of sensor level adjustment, PS1S sensor was not H Sensor cleaning PAC PS1S 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.
FF01 <Pre-Acceptor>Over max light PS2S sensor At the time of sensor level adjustment, PS2S sensor was not H Sensor cleaning PAC PS2S 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.
FF02 <Pre-Acceptor>Over max light PS3S sensor At the time of sensor level adjustment, PS3S sensor was not H Sensor cleaning PAC PS3S 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 51 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
FF03 <Pre-Acceptor>Over max light PS4S sensor At the time of sensor level adjustment, PS4S sensor was not H Sensor cleaning PAC PS4S 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.
FF04 <Pre-Acceptor>Over max light PTCS sensor At the time of sensor level adjustment, PTCS sensor was not H Sensor cleaning PAC PTCS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF05 <Pre-Acceptor>Over max light PASS sensor At the time of sensor level adjustment, PASS sensor was not H Sensor cleaning PAC PASS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF06 <Pre-Acceptor>Over max light PDSS sensor At the time of sensor level adjustment, PDSS sensor was not H Sensor cleaning PAC PDSS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF07 <Separator Transport>Over max light SDIS sensor At the time of sensor level adjustment, SDIS sensor was not H Sensor cleaning SEP SDIS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.
FF08 <Separator Transport>Over max light SDOS sensor At the time of sensor level adjustment, SDOS sensor was not H Sensor cleaning SEP SDOS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF09 <Separator Transport>Over max light SSLS sensor At the time of sensor level adjustment, SSLS sensor was not H Sensor cleaning SEP SSLS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.
FF0A <Separator Transport>Over max light SSRS sensor At the time of sensor level adjustment, SSRS sensor was not H Sensor cleaning SEP SSRS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF0B <Separator Transport>Over max light SSOS sensor At the time of sensor level adjustment, SSOS sensor was not H Sensor cleaning SEP SSOS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF0C <Escrow>Over max light EECS sensor At the time of sensor level adjustment, EECS sensor was not H Sensor cleaning ESC EECS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF0D <Escrow>Over max light ETLS sensor At the time of sensor level adjustment, ETLS sensor was not H Sensor cleaning ESC ETLS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF0E <Bunch Transport>Over max light EELS sensor At the time of sensor level adjustment, EELS sensor was not H Sensor cleaning ESC EELS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 52 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
FF0F <Bunch Transport>Over max light EERS sensor At the time of sensor level adjustment, EERS sensor was not H Sensor cleaning ESC EERS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF10 <Escrow Transport>Over max light EDLS sensor At the time of sensor level adjustment, EDLS sensor was not H Sensor cleaning ESC EDLS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF11 <Escrow Transport>Over max light EDRS sensor At the time of sensor level adjustment, EDRS sensor was not H Sensor cleaning ESC EDRS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF12 <Escrow Transport>Over max light ERLS sensor At the time of sensor level adjustment, ERLS sensor was not H Sensor cleaning ESC ERLS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF13 <Escrow Transport>Over max light ERRS sensor At the time of sensor level adjustment, ERRS sensor was not H Sensor cleaning ESC ERRS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF14 <Transport after BV>Over max light UGAS sensor At the time of sensor level adjustment, UGAS sensor was not H Sensor cleaning UT UGAS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF15 <Cassettes Transport>Over max light URHS sensor At the time of sensor level adjustment, URHS sensor was not H Sensor cleaning UT URHS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF16 <Transport before BV>Over max light UFHS sensor At the time of sensor level adjustment, UFHS sensor was not H Sensor cleaning UT UFHS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF17 <Reject Transport>Over max light UGDS sensor At the time of sensor level adjustment, UGDS sensor was not H Sensor cleaning UT UGDS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF18 <Reject Transport>Over max light UECS sensor At the time of sensor level adjustment, UECS sensor was not H Sensor cleaning UT UECS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF19 <Reject Transport>Over max light UEFS sensor At the time of sensor level adjustment, UEFS sensor was not H Sensor cleaning UT UEFS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 53 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
FF1A <Reject Transport>Over max light UERS sensor At the time of sensor level adjustment, UERS sensor was not H Sensor cleaning UT UERS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF1B <Cassette3 Transport>Over max light LT3S sensor At the time of sensor level adjustment, LT3S sensor was not H Sensor cleaning LT LT3S 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF1C <Cassette4 Transport>Over max light LFHS sensor At the time of sensor level adjustment, LFHS sensor was not H Sensor cleaning LT LFHS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF1D <Cassette1>Over max light CL1S sensor At the time of sensor level adjustment, CL1S sensor was not H Sensor cleaning CAS1 CL1S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF1E <Cassette1>Over max light CR1S sensor At the time of sensor level adjustment, CR1S sensor was not H Sensor cleaning CAS1 CR1S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF1F <Cassette2>Over max light CL2S sensor At the time of sensor level adjustment, CL2S sensor was not H Sensor cleaning CAS2 CL2S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF20 <Cassette2>Over max light CR2S sensor At the time of sensor level adjustment, CR2S sensor was not H Sensor cleaning CAS2 CR2S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF21 <Cassette3>Over max light CL3S sensor At the time of sensor level adjustment, CL3S sensor was not H Sensor cleaning CAS3 CL3S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF22 <Cassette3>Over max light CR3S sensor At the time of sensor level adjustment, CR3S sensor was not H Sensor cleaning CAS3 CR3S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF23 <Cassette4>Over max light CL4S sensor At the time of sensor level adjustment, CL4S sensor was not H Sensor cleaning CAS4 CL4S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF24 <Cassette4>Over max light CR4S sensor At the time of sensor level adjustment, CR4S sensor was not H Sensor cleaning CAS4 CR4S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 54 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
FF25 <Cassette1>Over max light CT1S sensor At the time of sensor level adjustment, CT1S sensor was not H Sensor cleaning CAS1 CT1S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF26 <Cassette2>Over max light CT2S sensor At the time of sensor level adjustment, CT2S sensor was not H Sensor cleaning CAS2 CT2S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF27 <Cassette3>Over max light CT3S sensor At the time of sensor level adjustment, CT3S sensor was not H Sensor cleaning CAS3 CT3S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF28 <Cassette4>Over max light CT4S sensor At the time of sensor level adjustment, CT4S sensor was not H Sensor cleaning CAS4 CT4S 301-304,307,309
cleared even if maximum level. Or a margin was not able to be
gotten.

FF29 <Escrow>Over max light ETRS sensor At the time of sensor level adjustment, ETRS sensor was not H or C Sensor cleaning ESC SE2 ETRS 301-304,307
cleared even if maximum level. Or a margin was not able to be
gotten.

FF** Sensor off error.Sensor is light even turn off

the sensor
FF50 <Pre-Acceptor>PS1S sensor off error PS1S sensor was not blocked even when turned off at sensor level H PAC PS1S 302,306,307
adjustment.
FF51 <Pre-Acceptor>PS2S sensor off error PS2S sensor was not blocked even when turned off at sensor level H PAC PS2S 302,306,307
adjustment.
FF52 <Pre-Acceptor>PS3S sensor off error PS3S sensor was not blocked even when turned off at sensor level H PAC PS3S 302,306,307
adjustment.
FF53 <Pre-Acceptor>PS4S sensor off error PS4S sensor was not blocked even when turned off at sensor level H PAC PS4S 302,306,307
adjustment.
FF54 <Pre-Acceptor>PTCS sensor off error PTCS sensor was not blocked even when turned off at sensor level H PAC PTCS 302,306,307
adjustment.
FF55 <Pre-Acceptor>PASS sensor off error PASS sensor was not blocked even when turned off at sensor level H PAC PASS 302,306,307
adjustment.
FF56 <Pre-Acceptor>PDSS sensor off error PDSS sensor was not blocked even when turned off at sensor level H PAC PDSS 302,306,307
adjustment.
FF57 <Separator Transport>SDIS sensor off error SDIS sensor was not blocked even when turned off at sensor level H or C SEP SE1 SDIS 302,306,307
adjustment.
FF58 <Separator Transport>SDOS sensor off error SDOS sensor was not blocked even when turned off at sensor H or C SEP SE1 SDOS 302,306,307
level adjustment.
FF59 <Separator Transport>SSLS sensor off error SSLS sensor was not blocked even when turned off at sensor level H or C SEP SE1 SSLS 302,306,307
adjustment.
FF5A <Separator Transport>SSRS sensor off error SSRS sensor was not blocked even when turned off at sensor level H or C SEP SE1 SSRS 302,306,307
adjustment.
FF5B <Separator Transport>SSOS sensor off error SSOS sensor was not blocked even when turned off at sensor level H or C SEP SE1 SSOS 302,306,307
adjustment.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 55 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
FF5C <Escrow>EECS sensor off error EECS sensor was not blocked even when turned off at sensor level H ESC EECS 302,306,307
adjustment.
FF5D <Escrow>ETLS sensor off error ETLS sensor was not blocked even when turned off at sensor level H ESC ETLS 302,306,307
adjustment.
FF5E <Bunch Transport>EELS sensor off error EELS sensor was not blocked even when turned off at sensor level H ESC EELS 302,306,307
adjustment.
FF5F <Bunch Transport>EERS sensor off error EERS sensor was not blocked even when turned off at sensor level H ESC EERS 302,306,307
adjustment.
FF60 <Escrow Transport>EDLS sensor off error EDLS sensor was not blocked even when turned off at sensor level H ESC EDLS 302,306,307
adjustment.
FF61 <Escrow Transport>EDRS sensor off error EDRS sensor was not blocked even when turned off at sensor H ESC EDRS 302,306,307
level adjustment.
FF62 <Escrow Transport>ERLS sensor off error ERLS sensor was not blocked even when turned off at sensor level H ESC ERLS 302,306,307
adjustment.
FF63 <Escrow Transport>ERRS sensor off error ERRS sensor was not blocked even when turned off at sensor level H ESC ERRS 302,306,307
adjustment.
FF64 <Transport after BV>UGAS sensor off error UGAS sensor was not blocked even when turned off at sensor H UT UGAS 302,306,307
level adjustment.
FF65 <Cassettes Transport>URHS sensor off error URHS sensor was not blocked even when turned off at sensor H UT URHS 302,306,307
level adjustment.
FF66 <Transport before BV>UFHS sensor off error UFHS sensor was not blocked even when turned off at sensor level H UT UFHS 302,306,307
adjustment.
FF67 <Reject Transport>UGDS sensor off error UGDS sensor was not blocked even when turned off at sensor H UT UGDS 302,306,307
level adjustment.
FF68 <Reject Transport>UECS sensor off error UECS sensor was not blocked even when turned off at sensor H UT UECS 302,306,307
level adjustment.
FF69 <Reject Transport>UEFS sensor off error UEFS sensor was not blocked even when turned off at sensor level H UT UEFS 302,306,307
adjustment.
FF6A <Reject Transport>UERS sensor off error UERS sensor was not blocked even when turned off at sensor H UT UERS 302,306,307
level adjustment.
FF6B <Cassette3 Transport>LT3S sensor off error LT3S sensor was not blocked even when turned off at sensor level H LT LT3S 302,306,307
adjustment.
FF6C <Cassette4 Transport>LFHS sensor off error LFHS sensor was not blocked even when turned off at sensor level H LT LFHS 302,306,307
adjustment.
FF6D <Cassette1>CL1S sensor off error CL1S sensor was not blocked even when turned off at sensor level H CAS1 CL1S 302,306,307,309
adjustment.
FF6E <Cassette1>CR1S sensor off error CR1S sensor was not blocked even when turned off at sensor level H CAS1 CR1S 302,306,307,309
adjustment.
FF6F <Cassette2>CL2S sensor off error CL2S sensor was not blocked even when turned off at sensor level H CAS2 CL2S 302,306,307,309
adjustment.
FF70 <Cassette2>CR2S sensor off error CR2S sensor was not blocked even when turned off at sensor level H CAS2 CR2S 302,306,307,309
adjustment.
FF71 <Cassette3>CL3S sensor off error CL3S sensor was not blocked even when turned off at sensor level H CAS3 CL3S 302,306,307,309
adjustment.
FF72 <Cassette3>CR3S sensor off error CR3S sensor was not blocked even when turned off at sensor level H CAS3 CR3S 302,306,307,309
adjustment.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 56 / 57
4. Error Code (Category + Detail)
*H=HW, J=Jam, C=Connection, S=SW and Setting, O=Operation
Related FRU Probable causes
Error Error Motor/
Error message How to when to detect error Check & Repalce Connector Sensor of errors
code category Solenoid
Main Other (Chapter 5)
FF73 <Cassette4>CL4S sensor off error CL4S sensor was not blocked even when turned off at sensor level H CAS4 CL4S 302,306,307,309
adjustment.
FF74 <Cassette4>CR4S sensor off error CR4S sensor was not blocked even when turned off at sensor level H CAS4 CR4S 302,306,307,309
adjustment.
FF75 <Cassette1>CT1S sensor off error CT1S sensor was not blocked even when turned off at sensor level H CAS1 CT1S 302,306,307,309
adjustment.
FF76 <Cassette2>CT2S sensor off error CT2S sensor was not blocked even when turned off at sensor level H CAS2 CT2S 302,306,307,309
adjustment.
FF77 <Cassette3>CT3S sensor off error CT3S sensor was not blocked even when turned off at sensor level H CAS3 CT3S 302,306,307,309
adjustment.
FF78 <Cassette4>CT4S sensor off error CT4S sensor was not blocked even when turned off at sensor level H CAS4 CT4S 302,306,307,309
adjustment.
FF79 <Escrow>ETRS sensor off error ETRS sensor was not blocked even when turned off at sensor level H ESC ETRS 302,306,307
adjustment.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002 57 / 57
5. Probable causes of errors
note 1) When errors are not fixed by the following measures or the measures cannot be taken because of missing parts, replace parts or FRUs.
2) Basically, deformed/damaged/worn parts shall be replaced, but if such parts are fixed by bending as an emergency measure, they shall be replaced later as
soon as possible.
3) All mechanical errors are likely to relate to parts missing. In particular, springs and fixing parts are easy to be lost. Therefore, visual check is always required
to see if all springs and fixing parts are installed in the area where an error has occurred.
4) Check the conditions of notes delivered to Reject bin to find a hint of what caused an error. (eg: When frequent scratches found, you can check error 012.)

How to check whether fixed : Execute Reset (Mechanical reset & Jam clear) and Deposit / Dispense operation using note.

Where to check Measures to be taken

General error

001 Note remain Is any note or a piece of note remaining on the transport rout? Remove remaining notes or a piece of note if any.
(Visual check)
002 Foreign object remain Is any dust, clips, coins or a piece of paper remaining on the transport rout? Remove remaining foreign object if any.
(Visual check)
003 Improper module setting Check if GBRU/GBNA is properly locked on Cradle having correct clearance When mounting, push the module until it is properly locked.
by moving it manually. If the module does not move smoothly, adjust the lock position to create
clearance of 0.3mm - 0.8mm.
004 Jam clearance areas not fully locked Are jam clearance areas completely closed and fully locked? Close all jam clearance areas until they are locked.
005 Improper cassette setting Is CASSETTE/RJ-BIN properly set? Insert a Cassette into a proper position.
When mounting, push RJ-bin until it is locked.
006 Unit information setting error Are the unit information settings about denomination, maximum number of Check denomination settings and if magnet positions or note width guide
notes or etc. appropriate? positions do not correspond to the settings, correct them.

007 Inappropriate note amount loaded Is the number of notes loaded in a cassette appropriate? (Cassette Full? Load appropriate number of notes.
Cassette Empty?)
Is note denomination correct?
008 Power supply and connection failure Are the power supply and controller connected properly? If they are not, reconnect them properly.
009 Module set unbalanced Are upper and lower modules mounted with a tilt or misalignment (between Adjust the module position and refasten a fixing screw for the slide rail.
upper and lower, left and right, front and back)? Are all the fixing parts
fastened? (Visual check)
010 Bad note quality Check condition of notes to be loaded. Check if notes are seriously damaged or have any adhesion of dirt on the
surface.
011 BV unit error - Reset
012 Pick-up mechanism adjustment failure Check the way how notes are rejected. Frequent errors caused by abnormal Separator: In the case of frequent errors due to abnormal note distance,
note distance, abnormal note length, double feed, skew? double feed and note length, turn the dial by 45 degrees counterclockwise.
Separator: In the case of frequent skew errors, turn the dial by 45 degrees
clockwise.
If the measures above show no improvement or deteriorate the problem, or
cause another problem, it is recommended to replace the modules.
Cassette: Replace cassettes.
013 Software problem - Power off & on
014 Firmware not downloading - Download the firmware.
015 RAS operation miss - -
016 Authentication operation miss - Authenticate communication
017 Authentication level not match - Execute RAS-FA using switch

Drive system error

101 Motor/Solenoid failure or damage Check if motor is rotating and solenoid is activating by a mechanical reset. Replace motors/solenoids.
Check for abnormal sound.
102 Motor/solenoid not fixed securely Is motor/solenoid mounted firmly? Is there any damage and deformation to Fix motor/solenoid properly.
the fixing brackets? (Visual check)
103 Pulley/Gear improper rotation Are pulley/gear properly fixed with a shaft and sliding smoothly without Fix the fixing part of pulley/gear properly again.
interfering surrounding parts? When pulley/gear do not move smoothly, disassemble them and then clean
(Check visually and manually) and remove foreign objects if any. When pulley/gear interfere with
surrounding parts, check for deformation.
104 Belt come off/torn off Visual check. Place a belt to a proper position. If belt still comes off, adjust belt tension.
Replace belts if torn or damaged.
105 Belt tension failure Check belt tension. Readjust belt tension.
106 Inappropriate Gear backlash Check the amount of gear backlash using a manual handle. If gears have a same diameter, try changing phase of gear engagement.
Lubricate gears.
107 Bearing rotation not smooth Check if bearing is deformed, damaged, or catching foreign objects, or if Remove foreign objects if any.
shaft is worn using a manual knob handle.
108 Thrust clearance of shaft insufficient Confirm that thrust clearance of shaft is not 0mm by hand. Remove foreign objects if any. If there is no foreign object, check for parts
deformation.
109 Link mechanism operation failure Is link/stud/hub deformed or catching foreign objects? (Check visually and Remove any foreign objects or lubricate. If the failure still arises, check for
manually) parts deformation.
Is link/stud/hub well lubricated? (Visual check)
110 Carrier drive cam phase missynchronous Check the engagement of cam by moving Carrier back and forth using a To adjust cam phase, align the matching marks on pulleys with those on the
manual handle. frame and then reattach Carrier drive belt.
111 Stage/Pusher belt connection part disengaged Is belt connection part removed from Stage/Pusher? (Visual check) Connect the belt connection part to Stage/Pusher again.
112 Fork operation failure Is Separator fork deformed or damaged? (Visual check) Remove any foreign object or lubricate. If the failure still arises, check for
Check if Solenoid moves smoothly by pushing it by hand. parts deformation.
113 Escrow alignment lever operation failure Is ESC alignment lever deformed or damaged? (Visual check) Remove any foreign object or lubricate. If thrust clearance is needed, bend
Is there appropriate thrust clearance? the bracket slightly as an emergency measure. If the failure still arises, parts
Are notes stored in a proper position in ESC? may have been deformed or damaged to the extent that it is hard to repair.
114 Reservoir alignment lever operation failure Is RSV alignment lever deformed or damaged? (Visual check) Remove any foreign object or lubricate. If thrust clearance is needed, bend
Is there appropriate thrust play? the bracket slightly as an emergency measure. If the failure still arises, parts
Does RSV alignment lever move properly associated with RSV stage may have been deformed or damaged to the extent that it is hard to repair.
movement?
115 RSV storing lever operation failure Is RSV storing lever deformed or damaged? (Visual check) Remove any foreign object or lubricate. If the failure still arises, check for
Does RSV storing lever move properly associated with RSV stage movement? parts deformation.

116 Shutter open/close operation failure Is shutter deformed or damaged? (Visual check) Remove any foreign object or lubricate. If the failure still arises, check for
Check if shutter moves smoothly by opening and closing it by hand. parts deformation.
117

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/2
Transport system error

201 Flat belt come off/torn/damaged Visual check Replace flat belts.
202 Flat belt slip Does flat belt slip against flat pulley? (Check manually) Clean flat belt/flat pulley with alcohol. If flat pulley does not rotate smoothly,
disassemble it and clean its hole and the shaft.
203 Transport roller disengaged/worn/damaged Visual check If transport roller is out of position, return it in place.
204 Transport roller slip Does transport roller maintain sufficient transport force? Put a note between Clean roller surface with alcohol if transport force is significantly reduced.
transport rollers and pull it by hand to check transport force.
205 Transport guide deformation, Is transport guide deformed or damaged? Properly mounted? (Visual check) In the case of improper installation, re-mount transport guide properly.
mounting failure
206 Scratch, burr, adhesion of foreign object, protrusion on Is transport surface smooth? Remove any foreign objects adhered on transport surface. Try to plane away
transport surface any scratches and burrs. Smooth surface required.
207 Gate not smooth Confirm that thrust clearance of gate joint is not 0mm by moving it manually. Loosen a gate joint screw so as to generate thrust clearance of axis and fix it
Does gate interfere with surrounding parts? (Visual check) again.
208 Gate angle failure Is point of gate_fin protruding to transport surface? (Visual check) Loosen a gate joint screw and adjust gate position using turning clearance,
and then fix the screw again.
Or adjust the guide that covers the point of gate_fin and fix it again.
209 Rubber fin roller broken, disengaged Is any fin missing? Does rubber fin roller rotate stably? If some fins are lost, replace the module.
Note) The rubber fin roller of cassette is intermittent originally shape.
210 Carrier and Stage/Pusher tilted Are Carrier and Stage/Pusher assembled horizontally? (Visual check)y Level Stage/Pusher by adjusting drive belt phase.
211 Carrier and Stage/Pusher deformed or damaged Visual check Replace them.
212 Carrier and Stage/Pusher stopping position error Perform a mechanical reset to see if wrong positioning of Carrier and In the case of sensor disengagement, fix it.
Stage/Pusher interfere with Carrier movement and causes note collision.
213 Carrier interference Check if Carrier and Reservoir stage rubber interfere each other and also if If stage positioning sensor is disengaged, fix it.
Carrier is deformed or damaged visually.
214 Pre-Acceptor clamp tilted Is clamp flush against bottom transport belt? (check 4 points-left, right, front Readjust clamp using an adjustment screw if it is tilted.
and rear)
215 Pre-Acceptor clamp transport belt tension failure Is transport belt tension for clamp appropriate? Readjust belt tension.
216 Pre-Acceptor clamp up/down movement failure Check if clamp can move up to a required height, stay there and move down Readjust clamp tilt. In the case of sensor disengagement, fix it. Readjust
until it reaches bottom transport belt by performing a mechanical reset. surrounding drive belt tension/transport belt tension if necessary.
(Visual check)
217 Pre-Acceptor hook operation failure Check if hook can stand vertically and also lie down horizontally in RAS Adjust mounting position of hook drive solenoid.
mode.
Check if a standing hook is not easily fallen down when pushed by hand.
218 Pre-Acceptor tray operation failure Is tray deformed or damaged, or interfering with bottom surface? (Visual Replace trays if deformed or damaged.
check) Adjust drive belt tension.
Is there any foreign objects under tray? (Visual check) Remove foreign objects if any.
219 Pre-Acceptor and shutter engagement failure Is Pre-Acceptor transport surface connected to shutter with no gap and Readjust facing with Fascia.
without being pushed too much by Fascia. (Visual check)
220 A-stopper operation failure Check if A-stopper can stand vertically and also lie down horizontally in Readjust a position where A-stopper solenoid is fixed.
RAS mode, and check if a standing hook is not easily fallen down when
pushed by hand.
221 D stopper operation failure Check if D-stopper can stand vertically and also lie down horizontally in Readjust a position where D-stopper solenoid is fixed.
RAS mode.
222 Deskew roller operation failure Check if skew correction rollers and pinch rollers are not worn and can rotate Replace rollers if worn. Remove any foreign objects and clean.
smoothly.
223 Free gate operation failure Check if free gate moves smoothly and is not deformed/damaged. (Check Remove any foreign objects and clean.
manually and visually.)
224 BV does not face to transport guide Check if BV is mounted on Upper base without gap by visual check and if Adjust and fix BV/transport guide again.
transport guide is deformed/damaged.
225 Leaf spring failure at the entrance of reject bin Is the leaf spring located at the entrance of Reject box/Reject bin deformed? Replace leaf springs.
(Visual check)
226 Discharge brush failure Check if discharge brush is attached and is not worn out by visual check. Replace discharge brushes.
Check the continuity using a tester.
227 Reject Full detection lever operation failure Check if Note Full detection lever inside Reject bin moves smoothly by hand. Remove any foreign objects, clean and lubricate.
228
229
230

Electric system error

301 Connector not fully attached/Wrong connection Visual check Connect properly.
302 Breaking of cable/Short-circuit Visual check. Replace cables.
Check the continuity using a tester.
303 Sensor/Prism removal, optical axis misalignment Are sensor/prism/fixing parts removed or deformed? (Visual check) Fix sensor/prism.
304 Sensor/Prism dirty, scratched Check light receiving/emitting face of Sensor/Prism visually. Cleaning required. Or replace them if remarkable scratches found.
305 Sensor block plate deformed Visual check Repair deformed parts or replace.
306 Sensor damaged Check sensor output in RAS mode. Replace sensors.
Replace sensors and then check the output in RAS mode.
307 PCB or ROM failure Replace PCBs and then check the operation. Replace PCBs.
308 Overload detection failure Check cable connection and scratches visually. Refer to 301 - 307.
Check if sensor is damaged or removed.
309 Floating connector failure Is floating connector damaged/deformed or catching any foreign objects? Remove any foreign objects and clean.
(Visual check)
310 Fuse blown Visual check Replace fuses.
311 External noise Check ground connection. Fix earth connection, change cable layout.
312 Lever detection plate operation failure (Note Empty Check if detection plate fulcrum moves smoothly by hand. Repair deformed parts or replace.
check or others) Is lever detection plate deformed/damaged? (Visual check)
313 USB cable pulled out Visual check Connect properly.
314 USB cable damaged Visual check Replace the cable.
315 LAN cable between BRU and BV pulled out Visual check Connect properly.
316 LAN cable between BRU and BV damaged Visual check Replace the cable.
317 Power cable for BV pulled out Visual check Connect properly.
318 Power cable for BV damaged Visual check Replace the cable.

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
2/2
6. FRU code

FRU CODE Description

Mechanical
PAC Pre-acceptor (140/178/240/354mm)
SEP Separator
ESC Escrow and Reservoir
UT Upper transport (Removable reject bin/Fixed reject bin)
BVE BV Entry Transport
LT Lower transport (BRU4/BNA4/BNA2)
SHT Shutter
Sensor
BV BV Module (Single/Dual Sensor)
Electronic
UPCB Upper PCB with 7 segments LED
SPCB Separator PCB
LPCB Lower PCB (GBRU/BNA4/BNA2)
FPCB MCU (FRU memory controller) PCB
LSW Lead Switch for cassette setting
PSU Power supply
CM[1-4] Motor assembly for cassette (Recycle/Deposit)
FAN Fan for BV
Media Containers
CAS[1-4] Currency Cassette (Recycle/Deposit)
RJ Bin Reject Bin (removable)
Cabinetry & Harnessing
UB Upper Base
LB Lower base (BRU4/BNA4/BNA2)

ERROR CODE LIST of GBNA/GBRU

A3KD02160-A002
1/1