Manuals+ — User Manuals Simplified.

Sinco Intelligent Technology CUBE-BABY Combined Effect

Pedal User Manual

Home » Sinco Intelligent Technology » Sinco Intelligent Technology CUBE-BABY Combined Effect Pedal User
Manual

Sinco Intelligent Technology CUBE-BABY Combined Effect Pedal User Manual

CUBE BABY is a kind of portable and multi functional bass guitar effects. It preset three sets of original tone from
factory, the users can edit tone and save, and the method of operation is simple and intuitive. This effects has
built-in battery, which solves the problem of long distance power supply. CUBE BABY has contained 9 classic IR,
two effects of modulation (chorus, phase shift), one tape delay, one reverb effect, eight classic IR box models and
a high precision audio radiance. Besides, CUBE BABY is also equipped with recording function in mobile phone,
wireless music playback and audio interface. It is integrated a variety of effects and function in one, small size,
good performance, portable and excellent sound! It could be a good partner of your guitar.

Contents
1 The power supply
2 Effects module link
3 Rear Panel
4 Front panel
5 Effect module
6 LIVE/PRESET Mode
7 How to edit a tone
8 Technical Parameters
9 FCC Warning Statement
10 Documents /
Resources
11 Related Posts

The power supply

 It is equipped with built-in battery for power supply, which can last for 6 hours after full charge.
It can be directly used to power the device by mobile phone charging power supply or charging treasure. It
supports charging/electricity simultaneously.
The charging time depends on the output power of the charging transformer. For example, the charging head
with an output power of dc5.0v / 2.0A can be fully charged within 2 hours when the built-in battery is
exhausted.

Effects module link

Tuner , Pre-Amp , Modulation effect Delay effect —■ Reverb effect —> IR CAB

Rear Panel

1. IN:Used to connect signal input of guitar.

2. Power switch
3. USB port: Used to charging, built-in USB audio interface function. It can be connected to the computer for
recording playback, support computer software import third party IR CAB.
4. Mobile phone port: Used for recording and playback of mobile phones.
5. Headphone output: Connect to the listening headphone.
6. OUT:Mono output, connected to a speaker or mixer.

Front panel
 1. TYPE: Select different type of tone
2. GAIN: Distortion gain knob
3. TONE: Tone Brightness Knob
4. MOD: PHASER/CHORUS effect knob
5. TIME: Delay time button
6. FB: Feedback knob
7. MIX: Dry and wet ratio knob
8. REVERB: Reverb knob
9. IR CAB: Box simulation
10. VOLUME: Output volume knob
11. Wireless accompaniment light
12. Wireless music playback light
13. Charging light
14. C function foot switch
15. B function foot switch
16. A function foot switch

Effect module

1. AMP IR timbre module TYPE knob: select the TYPE of IR. Please refer to the following list for specific TYPE.
 IR NAME Tone type Gear

US GOLD 50 B surd 1

UK Gold Clean surd 2

Cali-MK 3 Clean overload 3

Power-Zone Dist overload 4 GAIN knob: Select box tone, specific model
please refer to Follow the list on the right.
TGAIN knob: Adjust distortion. MOD module
Power-Zone Clean overload 5 TONE knob: Adjust the brightness of the tone.

US Gold 100 Clean distortion 6

Cali JPA distortion 7

Cali JP B distortion 8

Gas Station Clean distortion 9

2. .DELAY module
TIME Knob : Control the delay time.
FB Knob : Control feedback size.
MIX Knob : Adjust the wet/dry ratio, and turn the MIX knob to the far left to turn off delay, the knob
indicator light off.
3. REVERB module
REVERB Knob : Turn to the far left to turn off, at which point the knob light goes out. The amount of
reverb to the right gradually increases. The REVERB knob light goes out when the REVERB module is
turned off.
4. IR module
IR CAB knob : A total of 9 gears, the first gear is closed gear, 2 to 9 gears are 8 different sizes of the box,
the following table is the factory preset box.
 The body name Box specifications The gear

Closed box mold 1

Fender Pro Princeton 1X12 2

Fender Pro Princeton II 1X12 3

Fender Pro Junioor 1X10 4

GH Dual Rectifier 4X12 5

Line 6 Vetta 1X10 6

Soldano 2×12 7

Recabinet Mesa Boogie Standard 4X12 8

Marshall 1960A & 1960B 2×12 9

CUBE BABY allows users to load third-party IR, using the USB cable that comes with the product to
import third-party IR box simulation files via the manufacturer’s free software cube-suite online computer.
Users can import IR files that cover the original factory for the loading location of the list above. >KWhen
the original IR documents are covered and replaced, they cannot be recalled, please be careful before
doing so.

5. TUNER Module
CUBE BABY contains a highly sensitive tuner, which is used as follows; Long step combination foot nail
“B+C” into TUNER tuning mode, the tuning meter using the parameter knob light on the host panel to
display the tuning of the tone and instant pitch, please see the illustration:

After tuning, press any pin to exit TUNER mode.

6. Wireless accompaniment input function
CUBE BABY includes wireless music playback, which allows users to play accompaniment during
practice or performance, and long-term stepping on the combination of “A+B” to turn on or off the
wireless accompaniment function. When the device is not connected successfully, the wireless light
flashes slowly, and when the connection to the phone/tablet settings is successful, the light lights up blue.
 Press the “A+B” pin again until the light goes out to exit this function.
7. Mobile recording function CUBE BABY includes high-quality phone recording capabilities that connect the
device’s phone socket to your phone/tablet via a random internal recording dedicated cable, and enable high-
quality recording using your phone/tablet recording software.

LIVE/PRESET Mode

CUBE BABY has two modes of operation, LIVE for real-time editing mode and PRESET mode. The initial power-
on default enters PRESET mode, short press the combination nail “B+C” for LIVE PRESET mode switching.

A. LIVE Mode In LIVE mode, the “A/B/C” function pin is responsible for turning the corresponding effect module
on/off, and the corresponding function light is always on or off. In LIVE mode, the user can edit the tone effect
chain and hold the pin for long to save.

B. PRESET Mode

1. this effect device for the user preset three classic tones for the factory tone;

Sound position Effect chain Type

A Foot switch Cali JP B +DELAY+REVEBR+IR CAB:Soldano 2X12 Distortion

Power-Zone Dist+DELAY +REVEBR+IR CAB: Fender Pro Princeton II 1X1

B Foot switch Overload
2

UK Gold Clean+CHORUS +DELAY +REVEBR+IR CAB:Fender Pro Junioo

C Foot switch Voiceless
r 1X10

2. In PRESET mode, use the A/B/C function to pin to select the factory tone or the user saves the tone. Unlimited
switching between preset three sets of tones, with the staple indicator for the selected tone flashing.

How to edit a tone

1. Power-on initialization; when the built-in battery is fully charged or the power supply USB cable is connected,
please turn off the power switch . At this time, the parameter button turns on from left to right and then from
right to left to self-test . After the host self-test is completed, the system defaults to the PRESET mode. The
tone on the current A / B / C pedal become the factory tone.
2. Press the B and C pedals at the same time to switch to LIVE mode. Then, please check whether all the
parameter buttons are turned off.Turn the VOLUME to the appropriate level, and the output volume should not
be too high, that will avoid damage to the connected speaker equipment.
3. To start editing the tone, press the C foot switch to open the become tone module, and set the TYPE button to
 the 7th position (please refer to the become data sheet for item 1 of question 4 in this guide) and select the
distorted tone named Cali JP B . Next, turn the GAIN distortion gain button to the 3 o’clock position, and select
the brightness of the tone you want.
I set the TONE parameter to the 12 o’clock position of the clock (the users can evaluates the distortion gain
and tone brightness parameters that needed).
4. Next, we step on the B foot switch to turn on the MOD and DELAY modules. Because I expected to adjust a
relatively pure distortion SOLO tone, I did not consider the effect of using MOD. Please turn the MOD knob to
the clock at 12 o’clock. The MOD effect is turned off, and the knob indicator is turned off. Then turn the MIX
button to turn on the DELAY effect. Turn the MIX knob to the 9 o’clock position, the FB knob to the 11 o’clock
position, and the TIME button to the 2 o’clock position. I need this tone with sufficient delay effect so that I can
play more smoothly with slower phrases.
5. Next we will on the A pedal to turn on the REVERB and IR CAB modules. Please adjust REVERB to the 11
o’clock position to make this tone reflect more space. Then I moved the IR CAB knob to the seventh position,
and I chose a Soldano 2X12 cabinet.
6. Next we need to adjust the output volume of the edited tone. I set the VOLUME knob to the 1-point position of
the clock. (It is recommended that you set the output volume value of the VOLUME knob according to your
needs)
7. When it is determined that the tone has been edited and the output volume is adjusted, we can save the edited
tone in the PRESET mode, so that we can call the edited tone at any time when playing. Please select the stud
positions you want to store (this effect supports the storage of three tones, which, the A / B / C stud positions in
the preset mode). Here I choose the A stud positions and long A stepping on the nail, the prompt of A stepping
on the foot switch will flash quickly, indicating that the tone is being stored, until the flashing stops, and the tone
has been stored.
8. At this time, the tone that was just edited has been successfully stored in the PRESET mode, covering the tone
preset by the factory in the A-stamp. We stepped on the B and C at the same time to switch from the LIVE
mode to the PRESET mode. Step on the A pedal to find the Cali .1P B distortion solo sound you Just saved.

Technical Parameters
 Input Standard 1/4″ interface mono/TS

Output Standard 1/4″ interface mono/TS

Sample rate 48K/24bit

Battery capacity 600mah

Size 162(D)X61(W)X23(H)mm

Weight 260g

Attachment Instructions, charging data cables, internal cables

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

Documents / Resources

Sinco Intelligent Technology CUBE-BABY Combined Effect Pedal [pdf] User Manual
CUBE-BABY, CUBEBABY, 2ARCP-CUBE-BABY, 2ARCPCUBEBABY, CUBE-BABY Combined
Effect Pedal, CUBE-BABY, Combined Effect Pedal

Manuals+, home privacy