621E/XT/XR

ARTICULATED WHEEL LOADER TIER III CERTIFIED

ENGINE DRIVETRAIN HYDRAULICS

Model Case Family IV, Transmission Pump (steering/implement)
667TA/EDB, Tier III certified 4F/3R Proportional w/Electronic Control Closed centered pressure/flow compensated
Type 4-stroke, turbocharged Module torque sensing autoshift/manual shift
Variable displacement
and air to air cooled and modulation
5.49 in3/rev 45.2 gpm @ 2000 rpm @ 3600 psi
Cylinders 6 Gears Helical cut
(171 L/min @ 2000 rpm @ 24 822 kPa)
Bore/Stroke 4.11 in x 5.20 in Gear ratios Forward Reverse
Loader control valve
(104 X 132 mm) 1st 4.012 3.804
Closed-center, sectional 2, 3 or 4-spool with
Displacement 409 in3 (6.7 L) 2nd 2.174 2.061 pilot control for lift, tilt and auxiliary
3rd 1.088 1.031 hydraulics, electromagnetic detents in float,
Fuel injection Electronic
4th 0.619 NA raise and rollback
Fuel #2 Diesel
Torque converter Loader auxiliary steering
Fuel filter Replaceable, full flow Hydraulic orbital center-pivot articulating
Stall ratio 2.66:1
spin-on cartridge w/on-demand oil flow
Differential Limited slip
Air filter Dry type element High pressure standby 3625 psi
w/45% transfer on front
w/warning restriction indicator (25 000 kPa)
and rear axles
Mid-mount cooling module Filtration
Front and rear axle
External independent mounted coolers 10-micron, full flow replaceable cartridges on
Differential ratio 3.18
Fan return line, condition indicator light for filter
Planetary ratio 6.40
Style 8 blade puller Final axle ratio 20.36
Diameter 32 in (813 mm)
Planetaries Outboard CYLINDERS
Water pump
Service brakes Lift cylinder
Style Integral
Hydraulically actuated, maintenance-free, Bore diameter 4.75 in (120.6 mm)
Engine oil multiple wet disc w/accumulator to all four Rod diameter 2.50 in (63.5 mm)
Pump operating angle ratings wheels
Stroke 31.00 in (787.6 mm)
Side-to-side Rated 35° Brake surface area 355 in2 per hub
Fore and aft Rated 35° (0.229 m2) Dump cylinder (Z-Bar & XR)
Oil filtration Replaceable, Bore diameter 5.00 in (127.0 mm)
full flow spin-on cartridge Parking brakes
Rod diameter 3.00 in (76.2 mm)
Spring-applied hydraulic release disc on
Horsepower – Peak Stroke 24.40 in (619.7 mm)
transmission output shaft
Max Power
Travel speeds – mph (km/h) w/20.5 x 25 L3 tires Dump cylinders (XT)
Gross 172 (128 kW) @ 1800 rpm
Net 162 (121 kW) @ 1800 rpm Forward Reverse Bore diameter 4.50 in (114.3 mm)
Standard Power 1st 4.3 (6.9) 4.5 (7.3) Rod diameter 2.50 in (63.5 mm)
Gross 156 (116 kW) @ 1800 rpm Stroke 32.58 in (819.9 mm)
Net 146 (109 kW) @ 1800 rpm 2nd 8.4 (13.5) 8.8 (14.2)
Economy Power 3rd 14.9 (23.9) 15.6 (25.0)
Gross 133 (99 kW) @ 1500 rpm 4th 24.0 (38.6) NA
Net 125 (93 kW) @ 1500 rpm
NOTE: Travel speeds at full engine throttle.
Torque – Peak
Max Power
Gross 538 lb·ft (730 N·m) @ 1600 rpm ELECTRICAL
Net 510 lb·ft (692 N·m) @ 1600 rpm Voltage 24 Volts, negative ground
Standard Power
Gross 530 lb·ft (719 N·m) @ 1300 rpm Alternator 65 amp
Net 508 lb·ft (689 N·m) @ 1000 rpm Batteries (2) 12 Volt
Economy Power
Gross 527 lb·ft (715 N·m) @ 1200 rpm
Net 508 lb·ft (689 N·m) @ 1200 rpm
Torque rise 33%
NOTE: Gross horsepower and torque per SAE J1995.
Net horsepower and torque per SAE J1349.

Page 1 of 6
 E
J
F
K
A
H
D

B L
G

DIMENSIONS
Height to –
A. Top of ROPS cab 133.6 in (3393 mm)
Drawbar 39.0 in (992 mm)
B. Wheelbase 114.2 in (2900 mm)
C. Ground clearance 14.4 in (365 mm)
D. Angle of departure 32°
Width –
Overall* w/o bucket 99.3 in (2523 mm)
Centerline tread 76.8 in (1950 mm)
Turning radius* – outside 206.7 in (5250 mm)
Turning angle –
From center 40°
Total angle 80°
Rear axle oscillation, total 24°
NOTE: *Dimensions taken with 20.5x25 L2/L3/XTLA TL tires. Additional dimensions on pages 3 & 4.

WEIGHT ADJUSTMENTS
Tipping Load Tipping Load
Weight Adjustment Adjustment
Select Options Adjustment Straight 40° Turn
20.5x25 12 ply L2 tires -100 lb (-45 kg) -76 lb (-35 kg) -67 lb (-30 kg)
20.5x25 12 ply L3 tires +228 lb (+104 kg) +173 lb (+78 kg) +153 lb (+69 kg)
20.5R25 XHA TL tires +380 lb (+172 kg) +288 lb (+131 kg) +255 lb (+116 kg)
Standard counterweight -854 lb (-387 kg) -2,044 lb (-927 kg) -1,713 lb (-777 kg)
Open ROPS -295 lb (-134 kg) -299 lb (-136 kg) -276 lb (-125 kg)
NOTE: **Unit equipped with Z-Bar loader arms, 2.5 yd3 (1.96 m3) general purpose pin on bucket w/bolt-on edge, 20.5R25 XTLA Michelin tires, ROPS cab with heater and A/C,
full counterweight, standard batteries, front and rear fenders, full fuel and 175 lb (79 kg) operator. Adjust select options from rated weight.

621E/XT/XR Page 2 of 6
 PERFORMANCE DATA
3.0 yd3 GP (2.29 m3) 2.75 yd3 GP (2.10 m3) 2.75 yd3 GP (2.10 m3)
621E Z-Bar* Bucket w/Bolt-on Edge Bucket w/Bolt-on Edge Bucket w/Teeth & Segments
SAE bucket capacity – struck 2.56 yd3 (1.96 m3) 2.32 yd3 (1.77 m3) 2.32 yd3 (1.77 m3)
Heaped 3.00 yd3 (2.29 m3) 2.75 yd3 (2.10 m3) 2.75 yd3 (2.10 m3)
Bucket width – outside 102.4 in (2602 mm) 102.4 in (2602 mm) 102.4 in (2602 mm)
Bucket weight 1,951 lb (885 kg) 1,856 lb (842 kg) 1,923 lb (872 kg)
E. Operating height – fully raised w/spillguard 198.1 in (5032 mm) 195.1 in (4955 mm) 195.1 in (4955 mm)
F. Hinge pin height – fully raised 150.8 in (3830 mm) 150.8 in (3830 mm) 150.8 in (3830 mm)
G. Overall length – bucket level on ground 290.7 in (7384 mm) 288.0 in (7316 mm) 293.8 in (7463 mm)
Dump angle – fully raised 55° 55° 55°
H. Dump height – fully raised, 45° dump 110.3 in (2801 mm) 112.0 in (2845 mm) 108.2 in (2749 mm)
J. Bucket reach – fully raised, 45° dump 39.9 in (1013 mm) 38.1 in (969 mm) 42.2 in (1071 mm)
K. Bucket reach – 7 ft 0 in (2.13 m) height, 45° dump 59.6 in (1515 mm) 58.8 in (1493 mm) 60.8 in (1544 mm)
Operating load – ISO 9,918 lb (4499 kg) 10,063 lb (4564 kg) 10,019 lb (4544 kg)
Maximum material density – ISO 3,306 lb/yd3 (1962 kg/m3) 3,659 lb/yd3 (2171 kg/m3) 3,643 lb/yd3 (2162 kg/m3)
Tipping load – ISO
Straight 22,795 lb (10 339 kg) 23,098 lb (10 477 kg) 23,009 lb (10 437 kg)
40° turn 19,836 lb (8998 kg) 20,126 lb (9129 kg) 20,037 lb (9089 kg)
Lift capacity –
Full height 16,363 lb (7422 kg) 16,464 lb (7468 kg) 16,396 lb (7437 kg)
Maximum reach 23,114 lb (10 484 kg) 23,221 lb (10 533 kg) 23,153 lb (10,502 kg)
Ground 22,841 lb (10 360 kg) 24,369 lb (11 054 kg) 24,323 lb (11 033 kg)
Breakout force w/tilt cylinder 23,249 lb (10 546 kg) 24,827 lb (11 261 kg) 24,762 lb (11 232 kg)
Maximum rollback –
Ground 41° 40° 41°
Carry position 44° 44° 44°
@ Maximum reach 53° 53° 53°
@ Full height 55° 55° 55°
L. Dig depth 3.4 in (87 mm) 3.2 in (81 mm) 3.5 in (89 mm)
Maximum grading angle w/bucket – back dragging 61° 60° 62°
Loader clearance circle 454.7 in (11 549 mm) 453.1 in (11 507 mm) 456.5 in (11 595 mm)

3.0 yd3 GP (2.4 m3) 2.5 yd3 GP (1.96 m3)

621E XT ACS Bucket w/Edge** ACS Bucket w/Edge**
E. Operating height – fully raised w/spillguard 215.8 in (5482 mm) 210.5 in (5347 mm)
F. Hinge pin height – fully raised 155.8 in (3956 mm) 155.8 in (3956 mm)
G. Overall length – bucket level on ground 298.9 in (7593 mm) 294.0 in (7468 mm)
Dump angle – fully raised 55° 55°
H. Dump height – fully raised, 45° dump 109.9 in (2792 mm) 113.1 in (2872 mm)
J. Bucket reach – fully raised, 45° dump 48.7 in (1141 mm) 44.9 in (1141 mm)
K. Bucket reach – 7 ft 0 in (2.13 m) height, 45° dump 66.7 in (1694 mm) 66.6 in (1692 mm)
Operating load – ISO 8,435 lb (3826 kg) 8,512 lb (3861 kg)
Maximum material density – ISO 2,669 lb/yd3 (1584 kg/m3) 3,200 lb/yd3 (1899 kg/m3)
Tipping load – ISO
Straight 19,489 lb (8840 kg) 19,690 lb (8931kg)
40° turn 16,869lb (7652 kg) 17,024 lb (7722 kg)
Lift capacity –
Full height 14,316 lb (6494 kg) 14,246 lb (6462 kg)
Maximum reach 20,401 lb (9254 kg) 20,275 lb (9197 kg)
Ground 36,131 lb (16 389 kg) 35,388 lb (16 052 kg)
Breakout force – dump cylinder 24,298 lb (11 021 kg) 26,756 lb (12 137 kg)
Loader clearance circle 452.3 in (11 489 mm) 450.3 in (11 438 mm)

3.0 yd3GP (2.29 m3) 2.75 yd3 GP (2.10 m3) 2.75 yd3 GP (2.10 m3)
621E XR Bucket w/Bolt-on Edge Bucket w/Bolt-on Edge Bucket w/Teeth & Segments
E. Operating height – fully raised w/spillguard 214.4 in (5445 mm) 211.3 in (5368 mm) 211.3 in (5368 mm)
F. Hinge pin height – fully raised 167.0 in (4243 mm) 167.1 in (4243 mm) 167.1 in (4243 mm)
G. Overall length – bucket level on ground 306.8 in (7792 mm) 304.1 in (7725 mm) 309.9 in (7871 mm)
Dump angle – fully raised 50° 50° 50°
H. Dump height – fully raised, 45° dump 126.5 in (3214 mm) 128.3 in (3259 mm) 124.5 in (3162 mm)
J. Bucket reach – fully raised, 45° dump 40.5 in (1029 mm) 38.7 in (984 mm) 42.8 in (1086 mm)
K. Bucket reach – 7 ft 0 in (2.13 m) height, 45° dump 73.7 in (1873 mm) 72.8 in (1850 mm) 75.1 in (1908 mm)
Operating load – ISO 8,089 lb (3669 kg) 8,210 lb (3724 kg) 8,167 lb (3705 kg)
Maximum material density – ISO 2,696 lb/yd3 (1600 kg/m3) 2,986 lb/yd3 (1772 kg/m3) 2,970 lb/yd3 (1762 kg/m3)
Tipping load – ISO
Straight 18,680 lb (8473 kg) 18,931 lb (8587 kg) 18,845 lb (8548 kg)
40° turn 16,178 lb (7338 kg) 16,420 lb (7448 kg) 16,335 lb (7409 kg)
Lift capacity –
Full height 15,884 lb (7205 kg) 15,981 lb (7249 kg) 15,914 lb (7218 kg)
Maximum reach 20,521 lb (9308 kg) 20,641 lb (9363 kg) 20,571 lb (9331 kg)
Ground 25,153 lb (11 409 kg) 25,433 lb (11 536 kg) 25,361 lb (11 504 kg)
Breakout force w/tilt cylinder 23,925 lb (10 852 kg) 25,557 lb (11 593 kg) 25,470 lb (11 553 kg)
Loader clearance circle 469.7 in (11 931 mm) 468.0 in (11 887 mm) 471.8 in (11 983 mm)

621E/XT/XR Page 3 of 6
 PERFORMANCE DATA
2.5 yd3 GP (1.96 m3) 2.5 yd3 GP (1.96 m3)
621E Z-Bar* Bucket w/Bolt-on Edge Bucket w/Teeth & Segments
SAE bucket capacity – struck 2.17 yd3 (1.66 m3) 2.17 yd3 (1.66 m3)
Heaped 2.56 yd3 (1.96 m3) 2.56 yd3 (1.96 m3)
Bucket width – outside 102.4 in (2602 mm) 102.4 in (2602 mm)
Bucket weight 1,792 lb (813 kg) 1,859 lb (843 kg)
E. Operating height – fully raised w/spillguard 194.0 in (4927 mm) 194.0 in (4927 mm)
F. Hinge pin height – fully raised 150.8 in (3830 mm) 150.8 in (3830 mm)
G. Overall length – bucket level on ground 285.1 in (7241 mm) 290.8 in (7387 mm)
Dump angle – fully raised 55° 55°
H. Dump height – fully raised, 45° dump 114.0 in (2895 mm) 110.2 in (2799 mm)
J. Bucket reach – fully raised, 45° dump 36.2 in (919 mm) 40.2 in (1021 mm)
K. Bucket reach – 7 ft 0 in (2.13 m) height, 45° dump 57.8 in (1467 mm) 59.9 in (1521 mm)
Operating load – ISO 10,190 lb (4622 kg) 10,146 lb (4602 kg)
Maximum material density – ISO 3,980 lb/yd3 (2362 kg/m3) 3,963 lb/yd3 (2352 kg/m3)
Tipping load – ISO
Straight 23,376 lb (10 603 kg) 23,289 lb (10 564 kg)
40° turn 20,379 lb (9244 kg) 20,292 lb (9204 kg)
Lift capacity –
Full height 16,533 lb (7499 kg) 16,465 lb (7469 kg)
Maximum reach 23,296 lb (10 567 kg) 23,228 lb (10 536 kg)
Ground 25,806 lb (11 705 kg) 25,768 lb (11 688 kg)
Breakout force w/tilt cylinder 26,577 lb (12 055 kg) 26,513 lb (12 026 kg)
Maximum rollback –
Ground 40° 40°
Carry position 44° 44°
@ Maximum reach 53° 53°
@ Full height 55° 55°
L. Dig depth 3.0 in (75 mm) 3.3 in (83 mm)
Maximum grading angle w/bucket – back dragging 60° 61°
Loader clearance circle 451.4 in (11 466 mm) 454.7 in (11 551 mm)

2.5 yd3 GP (1.96 m3) 2.5 yd3 GP (1.96 m3)

621E XT Case Bucket w/Edge*** Case Bucket w/Teeth
E. Operating height – fully raised w/spillguard 210.7 in (5353 mm) 210.7 in (5352 mm) NOTE: *Z-Bar performance data
F. Hinge pin height – fully raised 155.8 in (3957 mm) 155.8 in (3957 mm) shown w/full counterweight
**XT lift arm with buckets for
G. Overall length – bucket level on ground 300.8 in (7640 mm) 306.7 in (7791 mm)
ACS Pro Series 2000® size 30
Dump angle – fully raised 55° 55°
HD coupler.
H. Dump height – fully raised, 45° dump 108.7 in (2761 mm) 104.9 in (2663 mm)
***XT lift arm with bucket for
J. Bucket reach – fully raised, 45° dump 50.2 in (1275 mm) 54.1 in (1375 mm) Case coupler
K. Bucket reach – 7 ft 0 in (2.13 m) height, 45° dump 69.5 in (1766 mm) 71.2 in (1809 mm)
Operating load – ISO 8,267 lb (3750 kg) 8,206 lb (3722 kg) Performance data unit
Maximum material density – ISO 3,327 lb/yd3 (1974 kg/m3) 3,302 lb/yd3 (1959 kg/m3) equipped with 20.5R25 XTLA
Tipping load – ISO tires, ROPS cab w/heater and
Straight 19,068 lb (8649 kg) 18,945 lb (8593 kg) A/C, full counterweight,
40° turn 16,534 lb (7500 kg) 16,411 lb (7444 kg) standard batteries, front and
Lift capacity – rear fenders, full fuel and
Full height 14,899 lb (6758 kg) 14,786 lb (6707 kg) 175 lb (79 kg) operator.
Maximum reach 20,650 lb (9367 kg) 20,545 lb (9319 kg) Specifications per SAE J732,
Ground 33,099 lb (15 013 kg) 32,921 lb (14 933 kg) J1234, J695, J742
and J818.
Breakout force – dump cylinder 23,531 lb (10 674 kg) 21,376 lb (9696 kg)
Loader clearance circle 453.1 in (11 508 mm) 455.7 in (11 574 mm)

2.5 yd3 GP (1.96 m3) 2.5 yd3 GP (1.96 m3)

621E XR Bucket w/Bolt-on Edge Bucket w/Teeth & Segments
E. Operating height – fully raised w/spillguard 210.3 in (5340 mm) 210.3 in (5340 mm)
F. Hinge pin height – fully raised 167.1 in (4243 mm) 167.1 in (4243 mm)
G. Overall length – bucket level on ground 301.2 in (7651 mm) 306.9 in (7796 mm)
Dump angle – fully raised 50° 50°
H. Dump height – fully raised, 45° dump 130.3 in (3308 mm) 126.5 in (3212 mm)
J. Bucket reach – fully raised, 45° dump 36.8 in (934 mm) 40.8 in (1036 mm)
K. Bucket reach – 7 ft 0 in (2.13 m) height, 45° dump 71.6 in (1819 mm) 74.0 in (1880 mm)
Operating load – ISO 8,309 lb (3769 kg) 8,266 lb (3794 kg)
Maximum material density – ISO 3,246 lb/yd3 (1926 kg/m3) 3,229 lb/yd3 (1916 kg/m3)
Tipping load – ISO
Straight 19,145 lb (8684 kg) 19,060 lb (8646 kg)
40° turn 16,617 lb (7537 kg) 16,532 lb (7499 kg)
Lift capacity –
Full height 16,047 lb (7279 kg) 15,980 lb (7248 kg)
Maximum reach 20,729 lb (9402 kg) 20,659 lb (9371 kg)
Ground 25,667 lb (11 642 kg) 25,593 lb (11 609 kg)
Breakout force w/tilt cylinder 27,375 lb (12 417 kg) 27,287 lb (12 377 kg)
Loader clearance circle 466.0 in (11 836 mm) 469.8 in (11 932 mm)

621E/XT/XR Page 4 of 6
INSTRUMENTATION OPERATOR ENVIRONMENT SERVICE CAPACITIES
Electronic Information Center ROPS cab w/ heat Fuel tank 65 gal (246 L)
Displays/Gauges – Key start Hydraulic system
Speedometer Articulated power steering w/tilt column Total 39 gal (147.6 L)
Tachometer Reservoir 24 gal (90.8 L)
Fully adjustable, suspension seat
Direction selected F/N/R Transmission
Foot throttle
Transmission modes – Auto shift/Manual shift Service w/filter 5.0 gal (18.9 L)
Gear position 1-Lever loader control w/wrist rest
Front and rear axle
Engine coolant temperature Cup holder
Front axle 23.2 qt (22.0 L)
Fuel level Coat hook Rear axle 23.2 qt (22.0 L)
Transmission oil temperature
(1) Interior rearview mirror Engine oil w/filter 13.9 qt (13.2 L)
Hydraulic oil temperature
2 in (51 mm) retractable seat belt Cooling system (-40) 38 qt (36.0 L)
Hourmeter
Work mode Storage tray behind seat

Indicator lights – Cooled lunch box

OPERATING WEIGHTS
Low fuel Single brake pedal
Z-Bar
Turn signals F/N/R shuttle switch
Unit equipped with ROPS cab with heater and
High beam lights External rear view mirrors A/C, full counterweight, 20.5R25 XTLA Michelin
Grid heater* tires, front and rear fenders, 2.5 yd3 (1.96 m3)
Lock box
Brake pressure general purpose loader bucket w/edge,
Master indicator Pressurized air filtering full fuel, 175 lb (79 kg)
Anti-glare window strip operator 27,406 lb (12 431 kg)
Secondary steering*
Parking brake Defroster XT

Audible alarms – Side window, partial/fully open Unit equipped with ROPS cab with heater and
Caution alarm A/C, full counterweight, 20.5R25 XTLA Michelin
Dome light tires, 2.5 yd3 (1.96 m3) ACS loader bucket,
Critical alarm
Wipers, rear and intermittent front standard batteries, full fuel, 175 lb (79 kg)
Backup alarm operator 28,709 lb (13 022 kg)
Windshield washers, front and rear
Horn XR
Rubber floor mat
NOTE: *If equipped with option. Unit equipped with ROPS cab with heater and
A/C, full counterweight, 20.5R25 XTLA Michelin
LOADER tires, front and rear fenders, 2.5 yd3 (1.96 m3)
general purpose loader bucket w/edge,
Z-bar loader linkage full fuel, 175 lb (79 kg)
Single control for lift and tilt operator 27,604 lb (12 521 kg)

Positive hold float

Automatic return-to-dig
Automatic height control
Automatic return-to-travel
Brake pedal transmission disconnect
Bucket position indicator on bucket

CYCLE TIME
Raise w/rated bucket load 6.3 sec
Dump w/rated bucket load
Z-Bar 1.3 sec
XT 1.7 sec
Lower (empty)
Power down 4.7 sec
Float down 4.6 sec

621E/XT/XR Page 5 of 6
STANDARD EQUIPMENT
OPERATOR’S ENVIRONMENT LOADER HYDRAULICS
See page 5 See page 5 Single lever 2-spool loader control valve
ENGINE DRIVETRAIN Low-effort steering
Case Family IV 667TA/EDB 4-wheel drive Hydraulic driven fan
Tier III certified 4F/3R Selectable autoshift/manual shift (8) Diagnostic quick couplers
Selectable work modes transmission OTHER
Max power Electronic Control Module – Programmable, Electric hood lift
computer controlled proportional shifting with
Auto power Front and rear fenders
programmable gear selection
Standard power Lights –
Onboard diagnostics
Economy power (2) Front driving headlights (high/low beam)
Single lever electronic shift control
Turbocharger (2) Front flood
F/N/R switch in loader control handle
Charge air cooling (2) LED stop and tail lights
Downshift button
Automatic fan belt tensioner (2) Rear flood
Torque converter
Integral engine oil cooling Front and rear turn signal/flash
Outboard planetary axles
Fuel filter w/water trap Standard counterweight
Limited-slip differentials
Dual element air cleaner Drawbar hitch
Transmission oil cooler
65 amp alternator Articulation locking bar
Brake pedal transmission disconnect
(2) 700 CCA 12-volt batteries Lift arm locking bar
Hydraulic wet disc brakes
Liquid-cooled radiator Lift and tie-down points – front/rear
Spring-applied hydraulic release parking brake
Non spark-arresting muffler Backup alarm
Limp-Home Mode
Mid-mounted cooling module Remote drain points
Lubed-for-life drive shaft
Common rail electronic fuel injection

OPTIONAL EQUIPMENT
OPERATOR’S COMPARTMENT ENGINE TIRES
Cloth-covered air-suspension seat Cold weather package 20.5-25 12 PR L3 bias (rock)
Sound Shield noise suppression package Heavy-duty batteries 20.5 R25 radial (dirt/traction)
Cab air-conditioning w/heater Fuel heater 20.5 R25 radial (rock)
Radio Hydraulic oil cooler bypass
OTHER
Radio-ready (12 or 24-volt) Low temperature hydraulic oil
Special paint
Auxiliary power (12-volt) Grid heater
Full coverage fenders
Cab convenience package LOADER Belly pan
RH steps and platform Hydraulic attachment coupler systems Tool box
Rotating beacon Attachment auxiliary hydraulics Full counterweight - Z-Bar
Second brake pedal Buckets (see page 3 & 4) Temperature controlled fan
Open ROPS XT Linkage
Joystick steering XR Extended reach
HYDRAULICS
Auxiliary hydraulics
Ride Control
Secondary steering
3 or 4-spool loader valves with 2 or 3-lever
loader control
Hydraulic reversing fan
Hydraulic cooler

NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices,
where applicable.
NOTE: All engines meet current EPA emissions requirements.
IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifications
without notice and without incurring any obligation relating to such change. Case Construction
Equipment Inc. does not warrant the safety or reliability of attachments from other manufacturers.
Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods www.casece.com
and/or services of companies other than CNH America LLC, are the property of those respective companies.

Form No. CCE6230802R Printed in U.S.A. © 2009 CNH America LLC

Replaces form no. CCE6230802 All Rights Reserved

All Case construction equipment is biodiesel ready.