c2k_spi_probe c2k_otp_probe. cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000 class init complete tmu init complete bmu1 init: done bmu2 init: done util init complete GPI1 init complete GPI2 init complete HGPI init complete HIF rx desc: base_va: 03e80000, base_pa: 03e80000 HIF tx desc: base_va: 03e80400, base_pa: 03e80400 HIF init complete bmu1 enabled bmu2 enabled pfe_hw_init: done pfe_firmware_init pfe_load_elf pfe_load_elf no of sections: 10 pfe_firmware_init: class firmware loaded pfe_load_elf pfe_load_elf no of sections: 10 pfe_firmware_init: tmu firmware loaded pfe_load_elf pfe_load_elf no of sections: 14 pfe_firmware_init: util firmware loaded miidev_restart_aneg for PHY4 miidev_restart_aneg for PHY0 Using ENV from SPI Flash. nand_probe: comcerto_nand base: 0xc8300000 size: 0x2048 MB NAND type unknown: 00,00 No NAND device found!!! Malloc space: 0x00b00000 -> 0x01000000 (size 5 MB) Stack space : 0x00af8000 -> 0x00b00000 (size 32 kB) running /env/bin/init... Button VAR: btn_status set to 0 [INFO] Waiting for WD Magic Packet (5 sec): CTRL+C to skip...
Hit any key to stop autoboot: 1
init_sata: serdes: 24Mhz ref clk Serdes 1 : CMU OK Serdes 1 : Lane OK Serdes 2 : CMU OK Serdes 2 : Lane OK cap 0x6f26ff81 port_map 0x3 n_ports 2 P#SERR 0x4050002 IS 0x0 Port 0 control: 0x300 Port 0 status: 0x123 P#SERR 0x0 IS 0x0 Port 1 control: 0x300 Port 1 status: 0x0 GHC 0x80000000 GHC 0x80000002 ahci_init_one: SUCCESS
SATA Controller Info:
AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part Enter start port: 0 Port 0 status: 123 cmd_slot = 0xb06000 cmd_tbl_dma = 0xb06500 Exit start port 0 ahci_exec_ata_cmd: 512 byte transferred. Device support LBA48 pio 0003, udma 007f ahci_exec_ata_cmd: 0 byte transferred.
SATA Device Info:
Serial Number : WD-WMC4N1107889 Product model number : WDC WD20EFRX-68EUZN0 Firmware version : 80.00A80 Capacity : -387938128 sectors ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 1024 byte transferred. sataenv: partition 7 loading size 522 Button VAR: btn_status set to 0 ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 512 byte transferred. ahci_exec_ata_cmd: 10485760 byte transferred. Success: 20480 sectors read into address 03008000 from sector 0x0089d000 Verifying Checksum ... OK Image Name: Linux-3.2.26 Created: 2015-07-09 18:30:50 UTC Image Type: <NULL> <NULL> <NULL> (<NULL>) Data Size: 3806072 Bytes = 3.6 MB Load Address: 0f008000 Entry Point: 0f008000 OK