Department of Mechanical Engineering

ASSIGNMENT QUESTIONS - I
Computer Aided Engineering and Drawing (BCEDK203)
Projections of Lines

Draw the front and top views of a line AB 70 mm long when it is placed parallel to HP
1 and Perpendicular to VP. Rear end of the line is 20 mm in front of VP and the line is 40
mm above HP.

A line AB 80 mm long has its end A 20 mm above the HP and 30mm Infront of VP. It is
2 inclined at 30° to HP and 45° to VP. Draw the projections of the line and find apparent
lengths and apparent inclinations

The top view PQ of a straight line is 70 mm and makes an angle of 600 with XY line.
The end P is 10 mm Infront of VP and 30 mm above HP. The difference between the
3
distances of P and Q above the HP is 45 mm. Draw its projections. Determine its true
lengths and true inclinations with HP and VP.

A line AB measuring 70 mm has its end A 15 mm Infront of VP and 20 mm above the

HP and the other end B is 60 mm Infront of VP and 50 mm above HP. Draw the
4
projections of the line and find inclinations of the line with both the reference planes of
projection.

A line PQ measures 80 mm in length. The point P is above HP and Infront of VP by 20

mm and 30 mm respectively. The distance between the end projectors is 50 mm. The
5
line is inclined to HP by 30°. Draw the projections of the line and specify its true
inclination with VP.
 Department of Mechanical Engineering
ASSIGNMENT QUESTIONS - I
Computer Aided Engineering and Drawing (BCEDK203)
Projections of Planes

Triangular lamina of 25mm side is resting on HP one of its corners, such that the
surface of lamina makes an angle of 60deg with HP. If the side opposite to the
1
corner on which the lamina rests makes an angle of 30deg with VP. Draws the
projection.

A regular pentagonal lamina of 25mm side is resting on VP with one of its sides
2 such that the surface makes an angle of 60deg with VP. The edge on which it rests
is inclined at 45deg to HP. Draw the projections

A hexagonal lamina of sides 25mm rests on one of its corners on HP. The lamina
3 makes 45deg to HP and the diagonal passing through the corner on which it rests
appears to be inclined at 30deg to VP. Draw the projections.

A Pentagonal lamina of edges 25mm is resting on VP with one if its corner such
that surface makes an of 300 to VP and the perpendicular bisector of the edges
4
passing through the corners on which lamina rests 450 to HP. Draw the TV and
FV of the lamina.

A pentagonal lamina of sides 25mm is having a side both on HP and VP. The
5 surface of the lamina is inclined at an angle of 60deg with HP. draw the TV and
FV of the lamina
 Department of Mechanical Engineering
ASSIGNMENT QUESTIONS - II
Computer Aided Engineering and Drawing (BCEDK203)
Projections of Solids

A hexagonal prism 25mm sides of the base and 50mm axis length rests on HP on one its
1 edges of the base. Draw the projection of the prism when the axis of the prism is inclined
to HP at 45 deg and VP at 30deg.

A pentagonal prism 25mm sides of base and 50mm axis length rest on HP on one of its
corners of the base such that the two base edges containing the corner on which it rests
2
make equal inclination with HP. Draw the projection of the prism when the axis of the
prism is inclined to HP at 40deg and inclined to VP at 30 deg.

A square pyramid 35mm sides of base and 60mm axis length rests on HP on one of its
3 slant triangular face. Draw the projection of the pyramid when the axis of the pyramid to
be inclined to VP at 45deg.

A hexagonal pyramid of 25mm sides of base and 50mm axis length rests on one of its
4 edges of the base which is inclined VP at 30 deg. Draw the projection of the pyramid
when the axis is inclined to HP at 45deg.

A square pyramids 35mm sides of base and 60mm axis length rests on HP one of its
corners of the base such that the two base edges containing the corner on which it rests
5
make equal inclination with HP. Draw the projection of the pyramid when the axis of the
pyramid is inclined to HP at 40deg and appears to be inclined to VP at 45deg.
 Department of Mechanical Engineering
ASSIGNMENT QUESTIONS - III
Computer Aided Engineering and Drawing (BCEDK203)
Isometric Projections

A triangular pyramid base side -40mm and height 50mm is placed centrally on a square
1
slab side 80mm and 20mm thick. Draw the isometric projection of the combination.

The frustum of a square pyramid of sides 40mm,20mm and height 60mm rest on the top
face of the square block of side 60mm and height 20mm. the base edges of the pyramid
2
are parallel to the top face of the square block. Draw the isometric projection of the
combination

A cone of base diameter 50mm and height 40mm is placed centrally on the top face of
3 square slab side-80mm and height 20mm. Draw the isometric projection of the
combination

A frustum of cone base dia50mm,top dia 25mm and height 50mm is placed centrally on
4 the top face of a cylinder dia 100mm and height 30mm. Draw the isometric projection of
the combination.

A hemisphere of diameter 50mm is centrally resting on top of a square prism of base

5 side 60mm and height 30mm such that the curved surface of the hemisphere is touching
the top face of the prism. Draw the isometric projection of the combination of the solids.
 Department of Mechanical Engineering
ASSIGNMENT QUESTIONS - III

Computer Aided Engineering and Drawing (BCEDK203)

Development of Lateral Surfaces of the Solids

Draw the development of lateral surface of a square pyramid with a 40mm base side and
1 a 60mm long axis, resting on its base on the HP such that two of its sides of the base are
parallel to VP.

Draw the development of lateral surface of the cone whose base diameter is 50mm and
2
axis is 60 mm long. The cone is resting on HP on its base

A square prism of base side 30mm and axis length 60mm is resting on HP on its base
with all the vertical faces being equally inclined to VP. It is cut by an inclined plane 60°
3
to HP and perpendicular to VP and is passing through a point on the axis at a distance
15mm from the top face. Draw the development of the lower portion of the prism.

A rectangular prism of base 30mmx20mm and height 60mm rests on HP on its base with
the longer base side inclined at 40° to VP. it is cut by a plane inclined at 45° to HP,
4
perpendicular to VP and bisects the axis. Draw the development of the lateral surface of
the prism.

A regular pentagonal prism of height 60mm and base edge 30mm rests with its base on
5 HP. The vertical face closet to VP is 30° to it. Draw the development of the truncated
prism with its surface inclined at 60° to its axis and bisecting it.