Scribd
Upload
48 views1 page

En Quick Start Guide TIA V13 Tool Calling Interface

Uploaded by

chikov.pvl
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views1 page

En Quick Start Guide TIA V13 Tool Calling Interface

Uploaded by

chikov.pvl
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Quick Start – TIA V13 - Tool Calling Interface (TCI)

1 Hardware

PROFINET 1.4 Note: This example assumes


(BW2528) Quick-Setup
an S7 – 1500 and a “BWU2828”
stainless steel Profinet Gateway.
Diagnosis The same applies for Profibus
and all Safety Gateways.
Slave Adr Tool

1.2 Pressing the “OK” key takes you to 1.5 For Gateways with integrated
the Gateway menu. Go to “Quick-Setup” safety monitor we recommend first
and run the “Store+Run” command. This referring to the “Quick Start –
1.1 Connect for example a EMERGENCY STOP”.
projects the slaves and brings them into
Bihl+Wiedemann AS-i light button
the data exchange. 1.3 Connect your PLC to the stainless steel
module (BW2528) having Address 1 to
Gateway and assign a unique name.
the Gateway.

2 Creating the device configuration

2.1 Configuring the S7-1500: Start 2.2 Assign the project a unique name. 2.3 Select the S7-1500 from the list 2.4 Select the CPU. Under “Properties”
TIA V13 and open a new project. and add it by clicking on “OK”. → “Ethernet addresses” assign an IP
address and a PROFINET device
name.

2.5 Install the corresponding GSDML under 2.6 In the hardware under “Other field 2.7 Now assign the PROFINET interface to 2.8 To configure general settings for the AS-i
“Options” → “Install general station devices” → “PROFINET IO” → “Gateway” the AS-i GW by clicking on “Not assigned” GW, you should select the AS-i GW and use
description file (GSD)”. → “Bihl+Wiedemann GmbH” → “AS-i” you and selecting “PLC_1.PROFINET_1”. “Properties” → “General” → “Ethernet
will find the gateway installed in Step 2.2. addresses” to make the settings for the IP
Drag&drop it into the PN-IO network. address and the device name.

2.9 Double-clicking on “AS-i GW” allows you 2.10 After you have made all the settings for 2.11 Before the project can be loaded, the 2.12 “Go Online” enables you to connect to
to select individual diagnostics lists and use the devices, select the CPU, then compile it PROFINET interfaces need to be assigned. the configured system.
drag&drop to insert them into the “Device using “Compile” and load the project into the If all the settings were correctly made, the
overview” window. device using “Load”. target system is found using “Start search”
IMPORTANT: “C1: Flags + Fault and then loaded using “Load”.
Detector” must be in the first slot so that
the diagnostics are correctly displayed
via TIA V13 !

2.13 To read out the diagnostics, simply 2.14 Select the AS-i GW. Right-clicking takes 2.15 Programming of the safety-relevant
2.15 The ASIMON project is automatically
right-click on “C1: Flags + Fault Detector” → you to the context menu, so that you can use devices can now be configured by ASIMON and
stored together in the TIA V13 project.
“Online & Diagnostics” → “Channel “Start Device Tool” to start the ASIMON then loaded into the AS-i GW.
Diagnostics”. program from TIA V13.

4 Important Note! Bihl+Wiedemann GmbH


Floßwörthstr. 41
This document is intended only as an aid for users of safety equipment. It does not
preclude proper testing, which is your own responsibility. Please therefore observe the D - 68199 Mannheim
corresponding safety instructions in the User's Manual. Tel.: (+49) 621/33996-0
Fax: (+49) 621/3392239
eMail: [email protected]

You might also like