002 Fuel Priming Pump - Rmove and Install - Electric Fuel Lift Pump

320 GC Excavator ZBT00001-UP (MACHINE) POWERED BY C4.4 Engine(M0092769...
Page 1 of 5
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 GC EXCAVATOR ZBT
Configuration: 320 GC Excavator ZBT00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly

C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4525-09 Publication Date -01/06/2015 Date Updated -22/05/2018
i05652782
Fuel Priming Pump - Remove and Install - Electric Fuel Lift

Pump (EFLP)
SMCS - 1258-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of

Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 2/12/2023
320 GC Excavator ZBT00001-UP (MACHINE) POWERED BY C4.4 Engine(M0092769... Page 2 of 5
NOTICE
Ensure that the plastic tube assemblies are installed in the original
positions. Failure to connect the plastic tube assemblies to the correct
ports will allow contamination to enter the fuel system. Serious damage
to the engine will result if contaminated fuel enters the fuel system.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
Illustration 1 g03411118
3. The fuel priming pump can be installed in any location on a machine. Ref to the Original
Equipment Manufacture (OEM) for the correct location.
4. Make temporary identification marks on tube assemblies in order to show the correct position
of the tube assemblies.
5. Place a suitable container below the fuel filter base in order to catch any fuel that might be
spilled.
6. Disconnect tube assembly (3) and tube assembly (4) from the assembly of primary fuel filter
(5).
7. Use Tooling (A) in order to plug the tube assemblies. Use Tooling (A) in order to cap the
connections on the primary fuel filter.
8. Disconnect the OEM harness assembly from the connection on harness assembly (7) for water
in fuel sensor (6).
9. Disconnect the OEM harness assembly from the connection on harness assembly (1).
10. Remove bolts (2) and remove the assembly of primary fuel filter (5) from the mounting.
Support the primary fuel filter as the bolts are removed.
11. If necessary, disassemble the assembly of primary fuel filter (5). Ref to Disassembly and
Assembly, "Water Separator and Fuel Filter (Primary) - Remove and Install" for the correct
procedure.
Installation Procedure
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of

Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
1. Ensure that the fuel priming pump is clean and free from wear and damage. If necessary,
replace the fuel priming pump.
2. If necessary, assemble the assembly of primary fuel filter (5). Ref to Disassembly and
Assembly, "Water Separator and Fuel Filter (Primary) - Remove and Install" for the correct
procedure.
Illustration 2 g03411118
3. Position the assembly of primary fuel filter (3) onto the mounting.
4. Install bolts (2) to the assembly of primary fuel filter (3).
For M8 8.8 graded bolts, tighten the bolts to a torque of 22 N·m (195 lb in).
For M10 8.8 graded bolts, tighten the bolts to a torque of 44 N·m (32 lb ft).
For different graded bolts, refer to the OEM for the correct torque values.
NOTICE
Ensure that the plastic tube assemblies are installed in the original
positions. Failure to connect the plastic tube assemblies to the correct
ports will allow contamination to enter the fuel system. Serious damage
to the engine will result if contaminated fuel enters the fuel system.
5. Remove plug from tube assembly (3). Remove cap from the connection on the primary fuel
filter.
6. Connect tube assembly (3) to primary fuel filter (5).
7. Remove plug from tube assembly (4). Remove cap from the connection on the primary fuel
filter.
8. Connect tube assembly (4) to primary fuel filter (5).
9. Connect the OEM harness assembly to the connection on harness assembly (7) for water in fuel
sensor (6).
10. Connect the OEM harness assembly to the connection on harness assembly (1).
11. Turn the fuel supply to the ON position.
12. Turn the battery disconnect switch to the ON position.
13. Prime the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime"for
the correct procedure.
Copyright 1993 - 2023 Caterpillar Inc. Sun Feb 12 08:15:45 UTC+0700 2023
All Rights Reserved.
Private Network For SIS Licensees.

002 Fuel Priming Pump - Rmove and Install - Electric Fuel Lift Pump

Uploaded by

Copyright:

Available Formats

002 Fuel Priming Pump - Rmove and Install - Electric Fuel Lift Pump

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

002 Fuel Priming Pump - Rmove and Install - Electric Fuel Lift Pump

Uploaded by

Copyright:

Available Formats

320 GC Excavator ZBT00001-UP (MACHINE) POWERED BY C4.4 Engine(M0092769...

Disassembly and Assembly

Fuel Priming Pump - Remove and Install - Electric Fuel Lift

Refer to System Operation, Testing and Adjusting, "Cleanliness of

1. Turn the fuel supply to the OFF position.

2. Turn the battery disconnect switch to the OFF position.

Refer to System Operation, Testing and Adjusting, "Cleanliness of

4. Install bolts (2) to the assembly of primary fuel filter (3).

6. Connect tube assembly (3) to primary fuel filter (5).

8. Connect tube assembly (4) to primary fuel filter (5).

11. Turn the fuel supply to the ON position.

12. Turn the battery disconnect switch to the ON position.

You might also like