Scribd Logo
Upload

Welcome to Scribd!

  • 8 views

    Curing Compound-K100 TDS

    Uploaded by

    EGO Animation

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Curing Compound-K100 TDS

    Uploaded by

    EGO Animation
    8 views2 pages

    Original Title

    CURING COMPOUND-K100 TDS

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    8 views2 pages

    Curing Compound-K100 TDS

    Uploaded by

    EGO Animation

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    Castech K100

    Technical Data Sheet


    Description Physical Properties*
    Castech K100 is a concrete curing PROPERTY TYPICAL RESULTS
    solution specially formulated from selected
    Appearance Colorless transparent solution
    silicone, film-forming auxiliaries and
    admixtures.Sprayed or applied to the Specific gravity 1.11±0.01g / ml
    concrete surface, after curing will form a
    PH value 13.5±0.5
    layer of dense film, to prevent the concrete
    within the free water evaporation too early Solid content ≥12%
    to achieve the purpose of self-support. *The above properties are average laboratory values

    Advantages Coverage
     Strong resistance to permeability Castech K100 may be applied to the
     Strong resistance to acid surface after mortar or concrete final setting.
    The range of dosage is 0.1- 0.2 kg/㎡.
     High solidification strength
     No corrosive effect on steel Application
     No delay effect on the setting time This product can be used to brush, large area
     Improve the hardness of wear-resistant of the use of spray gun spray.
    floor After the concrete or cement mortar after the
    final setting (cast-in-place concrete or
    Uses
    ground can be, or after stripping) can be
    Housing construction, road and other sprayed. General spray vertical and
    projects of cast-in-place concrete, horizontal each time, until the first time
    prefabricated components, wear-resistant spray drying film (about 1 - 2 hours later)
    floor, cement products. spray the second time, the second spray with
    the first spray direction perpendicular to
    Packing ensure uniform spraying. Spray the attention,
    Castech K100 is available in 200 kg drum. the nozzle from the concrete surface to
    about 30 cm is appropriate.
    Shelf Life
    Health & Safety
    12 months when stored in factory
    packed unopened bag, stored in a cool dry As with all chemical products, caution
    and elevated place away from direct should always be exercised. Protective
    sunlight. clothing, such as gloves and goggles,
    should be worn. See packaging/MSDS for
    Precautions specific instructions.

    The operation should pay attention to Treat any splashes to the skin or eyes with
    protect the eyes, spraying should be leeward fresh water immediately. Should any of the
    when the nozzle from the ground 30 cm is products be accidentally swallowed, do
    appropriate. not induce vomiting, but call for medical
    assistance immediately.
    It is not suitable for spraying when it rains,
    but the curing solution after filming, it will
    not affect the effect.
    The information contained herein is to the best of our

    Storage should be sealed, protected from knowledge, belief, and accuracy. However, hence the

    light. conditions of handling and usage beyond our

    control. We make no warrantee of results, and assume no

    Technical Support responsibility or liability for any damages or consequential

    damage incurred by the use of the product. Our products


    CasTech offers full technical
    are sold on the condition that the user shall evaluate
    support package to specifiers,
    them, as well as our recommendations. To determine
    contractors and end users, as
    their suitability for a particular purpose. The user is solely
    well as technical assistance on site
    responsible for the selection of Spraytek products.
    and after sales consultations.

    You might also like