Nex Fs700 v3 10 Update Procedure
Nex Fs700 v3 10 Update Procedure
10 Upgrade procedure
NEX-FS700
V3.10
Upgrade procedure for Win and Mac
November 2014
New features
With V3.10 firmware upgrade, the following functions will be available for your NEX-
FS700 camcorder:
Please note that if you have upgraded your NEX-FS700E or NEX-FS700EK into V3.00,
or your model is NEX-FS700R or NEX-FS700RH, you will need to install V3.10.
If you haven’t upgraded your NEX-FS700E/NEX-FS700EK into V3.00, then you will
need to install V2.10.
Firmware version is displayed. Check if “BODY” version is “Ver. 3.00” or “Ver. 3.01”:
Supported: Windows 8.1, Windows 8, Windows 7 SP1, Windows Vista 1 SP2 (Starter
edition is not supported). Windows XP is not supported.
Please close all other applications software before updating the system software.
• CPU: Intel processor (Core Solo and Core Duo processors are no longer
supported)
• Hard Disk space: 200 MB or more
• RAM: 512 MB or more
Please close all other applications software before updating the system software.
• USB cable: supplied with the camcorder; update functionality is not guaranteed
with any other USB cable.
IMPORTANT: Do not remove the AC adapter during the update. Otherwise, the
camera may become inoperable due to the sudden power shutdown.
Remove the memory card from the camcorder before starting this procedure.
Link should have been provided to you, or you may find it on the Support tab of NEX-
FS700 camcorder website.
Please save the downloaded file onto the Desktop of your computer (recommended).
For Windows 8/8.1 users: Under the initial settings of Internet Explorer, the update file
may be saved in the [Downloads] folder. Click the [Desktop] tile from the Start screen
and find the downloaded file in the [Downloads] folder by using Explorer.
Feed the camera with AC adapter, and never power it off until you have finished the
upgrade.
Connect the camera to the computer with the supplied USB cable.
After confirming “Mass Storage Connected” is displayed on the camera screen, click
[Next] on Firmware Updater.
If the USB CONNECT screen is not shown, please try the following methods:
1. Disconnect the USB cable from the camera, and then reconnect the USB cable.
2. If there is another unused USB terminal in the computer, reconnect the USB
terminal to that terminal
1. Click on the task tray at the lower right corner of the computer
screen in order to stop the USB connection.
2. Please keep the USB cable connected even after stopping the USB connection
on the computer with the above operation.
3. If those icons don’t appear on the task tray, please proceed to next step.
Touch “OK” on LCD to reset camera body, and then click [Next] on the Firmware
Updater.
Important: do not push “RESET” button on the camera; please proceed to the next
step.
After resetting, reconnection of the camera is verified, and the “Run the update” screen
appears on the Firmware Updater application.
Click [Run] to start the update. A progress bar will appear while updating (this task will
take approximately 5 minutes).
Important: never turn off the camera nor disconnect the USB cable while upgrading.
When the update is completed, a “Finish the update” screen will appear on the
Firmware Updater application.
After the update has finished, turn off the camera, remove the AC adapter, and then
turn on the camera again.
IMPORTANT: Do not remove the AC adapter during the update. Otherwise, the
camera may become inoperable due to the sudden power shutdown.
Remove the memory card from the camcorder before starting this procedure.
Link should have been provided to you, or you may find it on the Support tab of NEX-
FS700 camcorder website.
Please save the downloaded file onto the Desktop of your computer (recommended).
If you are using OS X v.10.10, you will also need to download and run DriverLoader
before software updates; it can be downloaded from the same Support tab.
[DL100_1411a] folder should have appeared on the Desktop; double click on it.
To load a kernel extension, the message prompts you to allow the application to make
changes. Type the password for the administrative account.
To load a kernel extension, the message prompts you to allow the application to make
changes. Type the password for the administrative account.
Note: if the pop-up “FirmwareUpdater cannot be opened because the identity of the
developer cannot be confirmed” appears, click “OK” and refer to the following
instructions:
1. Menu appears when clicking the icon while pressing [Control] key; select
“Open” from that menu:
If you still haven’t done it, remove the memory from NEX-FS700 before continuing.
Feed the camera with AC adapter, and never power it off until you have finished the
upgrade.
Connect the camera to the computer with the supplied USB cable.
After confirming “Mass Storage Connected” is displayed on the camera screen, click
[Next] on Firmware Updater.
If the USB CONNECT screen is not shown, please try the following methods:
1. Disconnect the USB cable from the camera, and then reconnect the USB cable.
2. If there is another unused USB terminal in the computer, reconnect the USB
terminal to such terminal
Important: do not push “RESET” button on the camera; please proceed to the next
step.
After resetting, reconnection of the camera is verified, and the “Run the update” screen
appears on the Firmware Updater application.
Click [Run] to start the update. A progress bar will appear while updating (this task will
take approximately 5 minutes).
Important: never turn off the camera nor disconnect the USB cable while upgrading.
When the update is completed, a “Finish the update” screen will appear on the
Firmware Updater application.