Scribd
Upload
13 views2 pages

Burst Mosfet Advanced

mosfet

Uploaded by

umbiumbian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
13 views2 pages

Burst Mosfet Advanced

mosfet

Uploaded by

umbiumbian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

// AirsoftTech.

dk

//////// WIRE PIN AN COMPONENT LAYOUT /////////


int MOSFET_PIN = 5; // The Digital pin that attaches to the MOSFET gate, to
turn it on and off.
int TRIGGER_PIN = A0; // The analog pin that attaches to the trigger pin

float R1 = 100; // 100Kohm // The Voltage devider resistor R1


float R2 = 10; // 100Kohm // The Voltage devider resistor R2

float MIN_BATTERY_VOLTAGE = 3.6 * 2; // I Want 3.6V per cell on 2 Cell battery. 2 *


3.6 = 7.2;

//////// CONFIG VALUES /////////


int Max_ON_Time = 200; // The time in MS for a full burst cycle...

//////// INTERNAL VALUES /////////


int TrigerStatus = LOW; // The state of the trigger LOW => Not pressed, HIGH =>
Pressed
int TriggerReadValue = 0; // The value read from the analog trigger pin. => 0-
1024
int CurrentSleepTime = 0; // The ammount of time the mosfet has been on.

float voltageDevider = 0.0909; //(R2 / R1 + R2)


float Vmax = 55; // Input voltage that would give 5v in voltage devider.
float VStep = 0.0537109375; // Each voltage step in the analog pin will indicate
this voltage is given.

float CurrentBatteryVoltage = 7.4; // Current battery Voltage.

// The setup routine runs once when you press reset.


void setup() {
// Initialize the digital pin as an output.
pinMode(13, OUTPUT); // LED pin
pinMode(MOSFET_PIN, OUTPUT); // Set the Mosfet pin as an output so that we
can send power to the mosfet.
digitalWrite(MOSFET_PIN, LOW); // Make sure we start with power OFF!
digitalWrite(13, LOW); // Make sure we start with power OFF!

voltageDevider = R2 / (R1 + R2); // Make ure that


Vmax = 5.0 / voltageDevider;
VStep = Vmax / 1024.0;

// Serial.begin(9600);
}

// The loop routine runs over and over again forever.


void loop() {
ReadTrigger(); // Update the trigger state
if(TrigerStatus == HIGH) // If the trigger is pushed.
{
SetMosfet(HIGH); // First turn the Mosfet On
while (TrigerStatus == HIGH)
{
if(CurrentSleepTime < Max_ON_Time){ // If we have not completed a
cycle
CurrentSleepTime = CurrentSleepTime + 1; // Leave the mosfet on, and
increase time counter.
} else {
SetMosfet(LOW); // If a full cycle has gone,
turn the Monfet Off.
}
delay(1); // Sleep for one milisecond
ReadTrigger(); // Update the trigger status (We
stay in the loop untill the trigger is released)
}
SetMosfet(LOW); // Make sure the Mosfet is off
when the trigger is released
CurrentSleepTime = 0; // Reset time counter when the
trigger is released.
}
}

// This function updates the trigger status when it's called.


void ReadTrigger()
{
int TriggerReadValue = analogRead(TRIGGER_PIN);
CurrentBatteryVoltage = VStep * TriggerReadValue;

// Serial.print("\t output = ");


// Serial.print(TriggerReadValue);
// Serial.print(" - ");
// Serial.println(CurrentBatteryVoltage);
// delay(10); // Sleep for one milisecond

TrigerStatus = LOW;
if(TriggerReadValue > 20) {
if(CurrentBatteryVoltage >= MIN_BATTERY_VOLTAGE ) {
TrigerStatus = HIGH;
}
}
}

// This function set the Mosfet state


void SetMosfet(int val)
{
// Serial.print("\t DigitalWrite = ");
// Serial.println(val);
// delay(10); // Sleep for one milisecond
digitalWrite(13, val); // turn the LED on / off to indicate what the
mosfet should be dooing
digitalWrite(MOSFET_PIN, val); // turn the Monfet on / off
}

You might also like