Thank you for choosing a HAVAL vehicle.

The more you know about your vehicle, the more pleasure and convenience you will
find when using it. So, you are kindly required: Read this manual carefully before
using your vehicle. You will find important information concerning the operation of
the vehicle, which will allow you to make full use of its technological advantages.
Also, you will get very useful information about driving safety,
traffic safety and vehicle maintenance.

Sincerely wish you a safe and happy journey!

1
 Overview

Vehicle equipment Manual timeliness

Please note that this manual contains all the All information provided in this manual is up to
standard equipment, country-specific equipment date at the time of publication.
and special equipment for this model series. Thus, However, due to continuous improvement of the
some equipment or features described in this product, the contents of this manual will be
manual may not be installed onto your vehicle or updated at any time without notice.
are only available in some markets. For specific Depending on the vehicle specifications, vehicles
configuration information, please refer to shown in the figure may differ from your vehicle.
relevant sales materials or consult your vehicle The display information (including pictures,
dealer. icons, texts and so on) included in this manual
are only for instructions. According to the vehicle
model configuration, software version and
Accessories, spare parts and Modifications
theme settings, the actual information displayed
Now we can buy not only genuine parts, but also a
may be different.
variety of other spare nongenuine parts and
Refer to the actual model for specific
accessories that are suitable for our vehicle. The
information.
use of nonauthentic spare parts and accessories
may adversely affect vehicle safety, even if these
About symbols
products have been approved by the relevant
⚠ Warning
national or regional authorities. Refer to replacing
This indicates a warning.
or installation of non-authentic spare parts and
Failure to observe these warnings may result in
accessories, the Great Wall Motors do not afford
serious injury or death. Such warnings tell you what
any responsibility and do not offer any certificate.
to do or what not to do so as to reduce the risk of
It is forbidden to modify vehicles with non-authentic
serious injuries or death.
products. Modifications with non-authentic products
may affect vehicle operability, safety or
⚠ Caution
durability and may even violate government
This indicates a precaution.
regulations.
Failure to observe these precautions may result in
In addition, vehicle damage and performance
damage to the vehicle or its equipment.
issues arising from modification are not covered
Such cautions tell you what to do or what not to do
by warranty of quality.
so as to avoid or reduce the risk of damage to the
It is forbidden to modify suspension, braking
vehicle and its equipment.
system and so on, which may adversely affect the
operate safety of vehicle.
Notice
It is forbidden to modify the fuse box of vehicle, unless it
This indicates a reminder.
may adversely affect the electrical system.
Such tips contain helpful information that may
Modification in electronic components, software and
be of use to you.
circuits will affect their functions and the normal
operation of other related components, especially
(Page X)
safety-related systems, thus affecting the operation
This symbol indicates that more details can be
safety of vehicles and increasing the risk of accidents
seen on this page.
or injuries. Therefore, please do not modify pipeline,
electrical parts and software.

2
Tips for safety
⚠ Warning
General precautions for your driving:
 Drive only when fully alert: the alcohol, drug,
medicine or anesthetic will slow down
driver’s response time and affect judgment
and coordination, which makes the vehicle
get out of control and results in severe
safety accidents.
 Drive carefully: be sure to drive carefully.
Always keep an eye on improper
movements of other drivers or pedestrians
on the road so as to make timely judgments
and prevent accidents.
 Concentrate on driving: be attentive when
driving. Anything that distracts the driver’s
attention, such as adjusting control buttons,
call up and answer a mobile phone or
reading, may give rise to a crash accident
and serious injury to you, passengers on the
vehicle and other people.

⚠ Warning
 When getting out of the vehicle, do not leave
children, pets or someone who needs to help
in the vehicle alone .
 Because the children, pets or someone who
needs to help cannot get out of the vehicle
and save themselves. The temperature in
the vehicle may be too high or too low in
different weather, which may cause the
passengers or pets in the vehicle injury even
death.
 If the children or pets touch the key, the
vehicle may move itself which is dangerous
for yourselves and the vehicle, including
starting the vehicle, releasing the parking
brake, shifting gears, operating the doors
and windows.

3
Appearance (Type I)

61DCA15C5F3C

Ⓐ The camera, depending on model Ⓘ Window 24

configuration, may be used for: Ⓙ Tailgate 21
Reverse camera 93
Ⓚ Rear Fog light 41
Around view monitor (AVM) 93
Ⓛ Rear tow hook cover 186
Ⓑ Rear Wiper 46
Ⓜ Front tow hook cover 186
Ⓒ High-mounted brake light
Ⓝ Front combination lamp
Ⓓ Rear combination l light
Ⓞ Side mirror 35
Ⓔ Roof rail 38
Ⓟ Door handle 19
Ⓕ Engine hood 30
Ⓠ Fuel door 29
Ⓖ Front wiper 45

Ⓗ Sunroof 26

4
Appearance (Type II)

AD2EE5CCE45C

Ⓐ The camera, depending on model Ⓘ Window 24

configuration, may be used for: Ⓙ Tailgate 21
Reverse camera 93
Ⓚ Rear Fog light 41
Around view monitor (AVM) 93
Ⓛ Rear tow hook cover 186
Ⓑ Rear Wiper 46
Ⓜ Front tow hook cover 186
Ⓒ High-mounted brake light
Ⓝ Front combination lamp
Ⓓ Rear combination light
Ⓞ Side mirror 35
Ⓔ Roof rail 38
Ⓟ Door handle 19
Ⓕ Engine hood 30
Ⓠ Fuel door 29
Ⓖ Front wiper 45

Ⓗ Sunroof 26

5
Interior trim

9BF688B011B3

Ⓐ Due to different model configurations, it may

Ⓚ Steerig wheel right button can be
use for:
be used for:
Cruise control system 100
Wiper control combination switch (electric) 45
Cruise control assist system 102
Wiper control combination switch (auto) 45
Virtual instrument adjustment 125
Ⓑ Virtual instrument 123
Ⓛ Audiovisual system control button
Indicator lights on the instrument 128
Ⓜ Hill descent control system button 117
Ⓒ Head up display 122
Ⓝ Electronic stability control button 119
Ⓓ Light control combination switch 41
Ⓞ Light height adjustment knob 43
Ⓔ Multimedia display 142
Ⓟ Instrument brightness adjustment
Ⓕ A/C outlets 50 button 43
Ⓖ Audiovisual system power supply button 139 Ⓠ Power supply switch 76
Ⓗ Auto parking assist system button 96 Ⓡ Hazard warning light button 42
Ⓘ Around view monitor button 93 Ⓢ Parking brake switch (EPB) 79
Ⓙ Air conditioning button 50 Ⓣ Shift knob 81
Ⓤ Mobile phone wireless charging 57
Ⓥ Storage box 59

6
7
Table of contents
This chapter introduces the method for operating on-board
1 Operation
vehicle equipment, such as keys, doors, windows and seats.

This chapter introduces the driving information, such as

2 Driving
vehicle start, gear shifting and instrument of the vehicle.

This Chapter introduces the Bluetooth telephone, system

3 Audiovisual system
setting and other audio-visual system related information.

This Chapter introduces the functional equipment, such as

4 Safety
antitheft system and seat belts.

This Chapter introduces the treatment methods for

5 Emergency
vehicle failures such as flat tyre and battery loss.

This Chapter introduces the routine inspection and regular

6 Maintenance
maintenance of the vehicle.

This Chapter introduces the vehicle parameters, identification

7 Technical data
number and other information.

8 Index This Chapter introduces the alphabetical index in this manual.

8
Operation Anti-pinch function 27
Key 16 Delay function 27
About the key 16 One-click closing 27
Button introduction 16 Automatic sunroof closing 27
Battery replacement 17 Initialization 28
Door lock 19 Refuelling 29
Locking and unlocking through the PEPS 19 Refueling method 29
Locking and unlocking with key buttons 19 Fuel information 29
Locking and unlocking with center control Engine hood 30
buttons 19 Opening 30
Unlock with the interior handle 19 Close 30
Locking and unlocking with the mechanical Seat 31
key 20 Headrest 31
Locking during emergencies 20 Front seat 32
Tailgate 21 Rear seat 33
Child safety lock 22 Rearview mirrors 35
Unlocking after flameout 20 Interior rearview mirror 35
Auto driving lock 23 Outside rearview mirror 35
Automatic resetting 23 Steering wheel 37
Automatic unlock upon collision 23 How to adjust 37
Anti-misoperation lock 23 Horn 37
Window 24 Roof rails 38
Window switch 24 Roof rack 38
Thermal protection function 25 Light control 39
Anti-pinch function 25 Light setting 39
Delay function 25 Light control combination switch 41
Speed closing 25 Follow me home function 42
Initialization 25 Daytime running lamp 42
Sunroof 26 Emergency braking warning 42
Opening and closing the sunroof 26 Emergency hazard flashers 42
Opening and closing of sunshade 26 Light height adjustment 43
Thermal protection function 27 Instrument brightness adjustment 43
Linkage function 27 Interior lights 43

9
 Wiper controls 45 Advice on driving in harsh environments
Electric wiper 45 68
Automatic wiper 45 Driving in foggy weather 68
Front wiper and washer setting 45 Driving in the rain 68
Air conditioning system 50 Wading drive 68
Air conditioning control panel 50 Driving during the hot seasons 69
A/C setting interface 52 Driving in cold season 69
A/C setting 54 Advice on driving during run-in period 72
Air conditioning control 55 Tyre 72
A/C vent 56 Friction lining of brake pad 72
Mobile phone wireless charging 57 Hybrid vehicles 73
Instructions 57 About hybrid vehicle 74
Interior equipment 59 Energy recovery 74
Sun visor 59 Power battery vent 75
Vanity mirror 59 Battery safety switch 75
Storage box 59 Power supply mode 76
Storage case 60 Power supply mode switching 76
Spectacle case 60 Starting and shutting down vehicle 77
Front cup holder 60 Starting the vehicle 77
Rear cup holders 60 Shutting down the vehicle 77
Bottle holder 61 Parking brake 79
Power supply socket 61 Tips for safety 79
Electronic parking brake 79
Automatic transmission 81
Driving
Introduction to gear position 81
Driving procedures 64
How to shift 81
Before driving 64
Crawling function 82
Precautions for driving 64
Start the vehicle 82
Precautions for passengers 64
Stop the vehicle 83
Parking the vehicle 67
Driving mode 84
Economic driving 67
Switching method 84

10
Single pedal function 85 Intelligent driving assist system 107
Single pedal function 85 Intelligent driving 107
Vehicle wash/trailer mode 87 Forward assist system 108
Vehicle wash/trailer mode 87 Lane keeping assist system 110
Fording mode 88 Rear side assist system 112
Wading mode 88 Traffic sign information 115
Steering wheel assist mode 89 Hill descent control system 117
Switching method 89 Hill descent control system introduction
Parking assist system 91 117
Safety tips 91 Instructions 117
Reverse radar 92 Driving assist system 118
Anti-collision radar 92 Tips for safety 118
Reverse camera 93 Anti-lock brake system 118
Around View Monitor (AVM) 93 Electronic braking force distribution
Auto parking assist system 94 system 118
Parking settings 96 Braking force assist system 118
Tyre pressure monitoring system 98 Traction control system 118
System introduction 98 Rollover prevention system 119
Monitoring function 98 Secondary collision mitigation system
Alarm function 98 119
Fatigue driving reminder system 99 HHC (Hill-start Hold Control) 119
Introduction of fatigue driving reminder Electronic power steering system 119
99 Electronic stabilization program 119
Instructions 99 Emission control system 120
Functional limitations 99 Tips for safety 120
Cruise control system 100 Oxygen sensor 120
Cruise control system introduction 100 Catalytic converter 120
Instructions 100 Fuel evaporation control unit 120
Cruise control assist system 102 Crankcase emission control unit 120
System description 102 On-board diagnostic system 121
Instructions. 102 Head-up display (HUD) 122
Queuing auxiliary function 105 About the system 122
Curve road auxiliary function 105 How to use 122
Lane center keeping function during
cruising 105
Functional limitations of the cruise assist
106
Sensor 106

11
 Virtual instrument 123
Safety
Summary 123
Seat belts 161
Steering wheel button 125
Wear the seat belt properly 162
Driving data interface 125
Pretensioner seat belt 162
Audio media interface 126
How to use the three-point seat belt 163
Bluetooth interface 126
Airbags 164
Navigation information interface 126
Tips for safety 164
Alarm information interface 126
Airbag 165
Menu setting interface 127
Front airbags 166
Indicator lights on the instrument 128
Front passenger airbag switch 167
Indicator lights on the instrument 128
Side airbags 168
Power supply management system 134
Curtain airbags 168
System introduction 134
Child restraint system 170
Information you should know 134
Safety instructions for child seat 170
Fixing point for child seat 171
Audiovisual system Recommended child seat categories 171
Safety prompt 138 Installation of child seat 171
Safety 138 Vehicle anti-theft system 174
About the use 138 System introduction 174
About the radio 138 System activation 174
About USB storage devices 138 Alarm trigger condition 174
About Bluetooth 138 Alarm cancellation 174
Panel 139 System off 174
Steering wheel buttons 139 Emergency cut-off system 175
Power supply switch 139 Emergency cut-off system 175
External devices 139 Event data recorder 176
Display screen 141 System introduction 176
Display screen operation 141 Data reading 176
Display screen status bar 141 Data disclosure 176
Interface introduction 142
Menu interface 142
Shortcut panel 145
Interconnection 146
System Setting 147
Voice assistant 152
Navigation system 155

12
Emergency Maintenance
On-board toolkit 179 Necessity of vehicle maintenance 193
Location of on-board toolkit 179 Engine compartment 194
Emergency tyre repair and inflation 180 Tips for safety 194
Inflater and tyre repair fluid 180 Fluid level 195
Emergency tyre repair 180 Engine oil 196
Tyre inflation 181 Brake fluid 197
In case of an accident 182 Engine/drive motor coolant 197
Traffic accidents occur to vehicles 182 Windscreen washer fluid 197
Jump start 183 Radiator and fan 198
Symptoms of a drained vehicle battery Safety labels and identifiers 198
183 Parts replacement 200
How to jump start the vehicle 183 Fuses 200
Engine overheating 185 Wiper blade 201
When the engine is overheated 185 Bulbs 203
Towing 186 Vehicle maintenance 204
Use a professional vehicle to tow 186 Tyre maintenance 204
Towing with the tow hook 187 Sunroof maintenance 204
Service and rescue 190 Battery 206
On-board telephone 190 Exterior maintenance 206
Call center 190 Interior maintenance 207
Emergency rescue 190 Anti-corrosion measures 208
Car networking function indicator 191 Long-term storage of the vehicle 209
Regular maintenance table 210

13
 Technical data
Vehicle identification 213
Vehicle identification number 213
Engine number 213
Overall Parameter 214
Basic specification 214
Power specification 214
Tire specification 215
Wheel specification 215
Braking specification 215
Fluid specification 216
Seat specification 217

Index
Alphabetical index 220

14
1 Operation
Key 16
Door lock 19
Windows 24
Sunroof 26
Refuelling 29
Engine hood 30
Seat 31
Rearview mirror 35
Steering wheel 37
Roof rails 38
Light controls 39
Wiper controls 45
Air conditioning system 50
Wireless charging 57
Interior equipment 59

15
 Key

Vehicle equipment Button introduction

Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

About the key 964859EEC481

(A) Lock button
(B) Unlock button
(C) Vehicle locating button
(D) Back door control button

Lock button
Press the lock button to lock all the doors and
back door. In this case, the turn signal lamp will
flash once.

DFCE00A8EDDF
(A) Mechanical key Notice
(B) Smart Key When the door is locked, if the turn signal lamps
(C) Key number tag do not flash, check whether all the doors and back
door and the engine hood are closed fully.
Notice
This communication device conforms to standards Unlock button
or technical requirements of NBTC. Press the unlock button to unlock all the doors
and back door. In this case, the turn signal lamp
Notice will flash twice.
 Store the key number tag in a safe place.
The key number tag has a code necessary for Notice
getting a new key. You may only request a new The door unlock mode can be set on multimedia via
mechanical key from the authorised service centre [Vehicle setting] → [In-car] → [Body]
by using this code. If the unlock mode is set to [driver] when the
 When purchasing or transferring the vehicle, unlock button is pressed, only the driver’s door
hand over the key number tag to the purchaser. and back door will be unlocked. At this time, if
the unlock button is pressed again, all vehicle doors
will be unlocked.
If the unlock mode is set to [Four Doors] , press
unlock button to unlock all the doors and back
door.

16
Vehicle locating button Battery replacement
When all doors and back door are locked, press ⚠ Warning
this button to turn on the locating function so The vehicle key contains a battery.
that you can quickly find your vehicle in a  The battery in the vehicle key is dangerous.
parking lot. Regardless it is a new battery or an old one,
Press it again during vehicle locating alarm to you should always keep away from children.
cancel the locating function.  If swallowed or put into any part of the body,
Notice the battery may cause serious or fatal injury
The door unlock mode can be set on multimedia in 2 hours or less.
via [Vehicle Settings] [【In-Car] [Light]  Seek medical attention if you suspect the
battery has been swallowed or placed in any
Back door control button part of the body.
Press and hold the back door control button to  Please dispose of used batteries according to
unlock the back door and press the back door local laws. Incorrect disposal of used
micro switch to open the back door within 30 batteries will damage the environment.
seconds after unlock.
⚠ Caution
⚠ Caution  Both hands must be dry during the process.
 Modifying the transmission frequency of Moisture may cause rusting of the battery.
the intelligent key, boosting the key’s  Do not touch or move any other parts.
transmission power (including by  The positive and negative terminals of the
installing a frequency-power amplifier), battery must be installed correctly.
connecting it to an external antenna, or  Be careful not to lose parts when replacing
using other transmitting antennas is the battery .
forbidden.
 It is strictly forbidden to use the key to interfere 1. Push the release button of smart key to eject
with various legal wireless communication the mechanical key.
services. Once such interference has been
discovered, the use of the key should be halted
and measures should be taken to prevent such
interference before resuming use
 The use of the key may be affected by the
interference of various wireless equipment,
resulting in short-term failure of its function.

E1536A109E1D
(A) Release button
(B) Mechanical key

17
 2. Pry open the cover of the key using a flathead
screwdriver, and remove the cover.

257B83A9D7D8

3. Take out the battery and insert a new battery in

its place.

B0B391378D50
When installing the battery, make sure that
the positive terminal of the battery is facing
down.
Battery model: CR2032

4. Install the rear key cover. After installation,

make sure that all the key buttons are working
properly.

18
Door lock

Vehicle equipment Locking

Please note that this manual contains all the Touch the lock sensor to lock all the doors and
standard equipment, country-specific equipment the tailgate. In this case, the turn signal lamp will
and special equipment for this model series. flash once.
Thus, some equipment or features described in Notice
this manual may not be installed onto your When the door is locked, if the turn signal lamps
vehicle or are only available in some markets. do not flash, check whether all the doors, the
For further configuration information, please tailgate and the engine hood are closed fully.
refer to relevant sales information or consult Notice
with your distributor selling the vehicle to you.  Only the doors with smart key detected can
be operated.
Locking and unlocking through the PEPS  Do not lock and unlock the door at the same time.
When you carry the smart key with you, you can  If you wear gloves to operate the door handle,
use the passive entry and passive start system you may not be able to unlock or lock the door.
(PEPS) to lock and unlock the vehicle door.  The radio waves of the PEPS is a little weak.
When they are surrounded by other radio
equipment or blocked by other barriers, the
communication between the smart key and
the vehicle may be affected and the system
will not work normally.
 Every time the door is successfully locked or
unlocked, the PEPS system will stop working
for 3 s.
Locking and unlocking with key buttons
See the key button for introduction ( Page 16)
A57BF698199F
(A) Lock sensor
Locking and unlocking with center
(B) Unlock sensor
control buttons
Unlocking
Touch the unlock sensor to unlock all the doors
and the tailgate. In this case, the turn signal lamp
will flash twice.
Notice
The door unlock mode can be set via [Vehicle
Settings][ In-Car][ Body] on the multimedia
display screen. If the unlock mode is set to
[ Driver] when the unlock button is pressed,
only the driver door and tailgate will be 8F40E1A4B746
unlocked. At this time, if the unlock button is (A) Unlock button
pressed again, all vehicle doors will be (B) Lock button
unlocked. If the unlock mode is set to [ Four The center control button is located on the
Doors, press unlock button to unlock all the driver's door. Press the central control buttons
doors and tailgate. to lock or unlock all doors.

19
 (หน้าที่ 20)
Unlocking with the interior handle

468DCB02AC78
361E36239106
When a vehicle door is locked, pulling the interior
handle will unlock it. Pull the handle again to open ⚠ Caution
the door. After unlocking the vehicle door, you must first
pull out the mechanical key in order to open the
Notice driver door.
Make sure that the child lock is not active when
opening the rear doors with the inner handle; Notice
otherwise, the rear doors cannot be opened. When the mechanical key is used to unlock the
Locking and unlocking with the door, the vehicle anti-theft alarm may be triggered.
mechanical key Locking during emergencies
1. Pull up the door handle and push the cover
from the inside to remove it.

4D20BEE53777
The front passenger’s door and the rear door are
equipped with the door emergency locking
EDB126DE58F3
2. Insert the mechanical key into the door lock device.
hole, and turn the key to lock or unlock the Insert the mechanical key into the emergency
door. For how to get the mechanical key, refer lock hole as shown in the figure, move it to the
to Replacement of Key Battery. lowest position, and then close the door to lock it.

20
 Notice 2. Press the tailgate from outside the vehicle to
If you need to use this method to lock the door, make sure that it is fully closed.
it means that the electric door lock system has ⚠ Warning
malfunctioned. In this case, please go to the  When closing the tailgate manually, be sure
authorised service centre for maintenance as to press the tailgate outside the vehicle to
soon as possible. make it completely closed.
Tailgate  Using the handle to close the tailgate can
pinch your hand and result in serious injury.
Manual tailgate
 Do not drive the vehicle when the tailgate is
Opening
open.
 No passengers are allowed in the luggage area.
 Be careful not to injury anyone near the
tailgate when opening or closing.
 When closing the tailgate, be careful not to
pinch any object, such as a bag or necktie.
 Do not allow children to operate the tailgate.
Otherwise, an accidental injury may be
caused.

B2D827F79BAF ⚠ Caution
 When you carry the smart key with you,  Do not use excessive force when opening the
press and pull up the tailgate microswitch. tailgate; otherwise, it will easily damage the
 When the power supply switch is in the OFF tailgate.
position, press and hold the tailgate control  Always be careful when opening the tailgate
button on the key, and press and pull up the in strong wind. The strong wind can cause the
tailgate microswitch within 30 seconds. tailgate to open too far and deform.
 When the driver door is unlocked, press and  If the tailgate is frozen or covered in snow
pull up the tailgate microswitch. and ice, do not force it open.
Closing  First use the heating function to warm the
interior of the vehicle, and then open the
tailgate.
 If you must open the tailgate in an emergency,
pour warm water on it to melt the ice. Once
the frozen spots loosen, try to open it.
 Do not install or paste any ornaments onto
the tailgate strut.
 Do not pull sideways the tailgate, otherwise,
the strut may be bent and deformed.

3C9858EA539B
Notice
1. Pull the tailgate handle downwards and
 When the ambient temperature is lower than
release the handle before the tailgate is
0℃, the tailgate strut may not be able
fully closed.

21
 Notice Notice
to automatically push the tailgate up. In this  If you need to move the emergency opening
case, you can manually lift the tailgate to open device with your hands, please try not to touch
it. the sheet metal parts to avoid scratching.
 Do not install heavy accessories on the tailgate.  If you need to use this method to open the
This can prevent the strut from smoothly tailgate, it means that the vehicle has
pushing the tailgate up. malfunctioned. In this case, please go to the
 The telescopic movement of the tailgate strut authorised service centre for maintenance as
needs oil-assisted lubrication, so it is normal soon as possible.
that there may be oil stains near the dust cover
of the strut. Child safety lock
Emergency unlock If there are child passengers within the vehicle, we
1.. Enter the vehicle and pry down the emergency recommend that they be seated in the comparatively
cover plate at the bottom of inner side of the safer rear seats where child safety locks are available
tailgate using a mechanical key with the corresponding vehicle doors to prevent
inadvertent opening of the vehicle doors.

B58F2872692D
Please refer to Replacement of Key Battery for the E1D0C7587D86
method to obtain the mechanical key. (▷ Page 20) Move the lever in the direction of the arrow to
2. Toggle the emergency opening device counter- activate the child safety lock. Move the lever in
clockwise in the direction shown in the figure the opposite direction to deactivate the child
to open the tailgate. safety lock.

⚠ Warning
Only the rear doors are equipped with child
locks. If a child is alone in the rear row, please
activate the child locks on both rear doors at the
same time to avoid accidents caused by
accidental opening of the doors.

Notice
After the child lock is activated, the door can
20BDF6834396 only be opened by pulling the door handle from
outside the car.

22
Unlocking after flameout Anti-misoperation lock
After the power supply mode changes from ON When the last door is closed with the driver's
to OFF mode, all vehicle doors and the tailgate door locked, all locked doors will be unlocked
will be automatically unlocked. The ignition off automatically.
and unlock function can be activate or
deactivated via
[Vehicle Settings] [In-car] [Body]
[Flameout Unlocking] on the multimedia
display screen.

Auto driving lock

All the doors and the tailgate are locked
automatically when the vehicle speed exceeds
15 km/h.
Vehicle speed of the auto driving lock can be
set via [Vehicle Settings] [In-car] [Body]
[Speed locking] on the multimedia display
screen.

Notice
Make sure that all doors and the tailgate are
completely closed before driving.

Automatic resetting
When the engine hood is closed and all the
doors and the tailgate are locked, if the power
supply mode and the state of all the doors and
the tailgate do not change within 30 seconds
after the doors from outside the vehicle are
unlocked (except the mechanical key), all the
doors and the tailgate will be automatically
locked.

Automatic unlock upon Collision

With the power in ON mode, when the system
detects a collision, all doors will be unlocked
automatically.

Anti-misoperation lock
When the last door is closed with the driver's
door locked, all locked doors will be unlocked
automatically.

23
Window

Vehicle equipment At this time, the vehicle window will be

Please note that this manual contains all the automatically opened completely. If you want to
standard equipment, country-specific equipment stop it halfway, you can just pull up the switch.
and special equipment for this model series. Pull up the vehicle window switch until it
Thus, some equipment or features described in exceeds the pressure point and then release the
this manual may not be installed onto your switch. At this time, the vehicle window will be
vehicle or are only available in some markets. automatically closed completely. If you want to
For further configuration information, please stop it halfway, you can just press the switch.
refer to relevant sales information or consult
with your distributor selling the vehicle to you. Notice
In some models, only the driver's window is
Window switch equipped with the one-button vehicle window
Driver's window switch opening and closing function.

⚠ Caution
In a low temperature environment, ice may
freeze between the vehicle window glass and
the vehicle window frame, and the glass may
fail in ascending and descending due to this
reason. Do not repeat the operation by force at
this time to avoid damage to the lifting
mechanism. After the temperature inside the
vehicle rises and the ice on the glass thaws, the
672B7229D35B glass will ascend and descend properly.
(A) Front passenger's side window
(B) Driver's window switch Vehicle window locking
(C) Window lock switch When the vehicle window locking switch is
(D) Rear window switch (L) pressed, the corresponding vehicle window
(E) Rear window switch (R) cannot be controlled by the vehicle window
Manual operation switch on the rear door. Pressing the vehicle
To open or close the vehicle windows, press or pull window locking switch again will recover the
up and hold the corresponding switch until the function of the rear vehicle window switch.
vehicle window reaches the required position. ⚠ Warning
When there are children in the vehicle, it is
⚠ Warning
recommended that they should sit in the relatively
Before closing the vehicle window, make sure
safe rear seats and the vehicle window locking
that all occupants' heads and hands have left the
function should be enabled.
vehicle window space, otherwise, it could cause an
Passenger's side window Switches
extremely serious injury.
On the armrest of the passenger's side door,
there is a window switch which can be used to
One-push raising or lowering
open or close the corresponding window.
Press the vehicle window switch until it exceeds
the pressure point, and then release the switch.

24
Thermal protection function Speed Closing
Thermal protection may be triggered to protect With the power supply in OFF mode, when all
the glass lifter motor after repeated operation the doors and back door are closed, press and
of the window switch. At this time, the window hold the lock button on the key or the lock
switch will temporary failure. The window switch sensor on the door handle to automatically
automatically returns to normal after the lifter close the windows.
motor cools down. Press the key unlock or lock button to stop
rising window if they are going up
Anti-pinch function automatically.
In the process of automatic vehicle window
closing, if a foreign object is sensed between Notice
the vehicle window frame and the vehicle If an obstacle between the window glass and
window, the vehicle window will stop closing the window frame is found during the
and automatically descend for a certain automatic ascending of the window glass, the
distance. anti-pinch function will be triggered, and the
Notice driver must confirm that the windows are
Due to different vehicle configurations, only the completely closed before leaving.
driver side vehicle window of some vehicles is
equipped with this function. Initialization
When errors occur in one-push raising or
⚠Warning
lowering function, you can reset it through the
 Never test the anti-pinch function with any
following operations:
part of your body.
1. Switch the power to OFF mode.
 At the moment when the vehicle window is
2. Pull up the window switches equipped with
complete closed, the anti-pinch function will
one-push raising or lowering function beyond
not work if something gets stuck.
the pressure point until the window is
Notice completely closed and then hold for about 3
Under severe conditions, such as low seconds.
temperature and severe bumping, the anti- 3. Operate the window switch again so that the
pinch function may be triggered in the process of window goes through the one-push raising
window glass ascending, and the vehicle window and one-push lowering.
cannot be closed smoothly. At this time, please
pull up the vehicle window switch till it exceeds Notice
the pressure point to close the vehicle window. When the one-push raising or lowering function is
disordered or every time the battery is
Delay function disconnected and re-energized, the windows
The vehicle windows can still be operated with one-push function need to be initialized.
within a few seconds after the power supply is
switched to OFF.
Notice
Some models are equipped with this function
on the driver side window only, depending on
the vehicle model.

25
Sunroof

Vehicle equipment ⚠ Warning

Please note that this manual contains all the  Do not put your hand or heads out of the
standard equipment, country-specific equipment sunroof when the vehicle is moving. If objects are
and special equipment for this model series. Thus, outside the vehicle when a emergency braking
some equipment or features described in this requirement, it may cause serious personal
manual may not be installed onto your vehicle or injury or even death.
are only available in some markets. For specific  When closing the sunroof, be careful not to
configuration information, please refer to clip other people's hands, heads and neck etc.
relevant sales materials or consult your vehicle to prevent serious personal injury.
dealer.  Do not allow children to operate the sunroof.

Opening and closing the sunroof Opening/closing of sunshade.

11C12A9BF507 E10A12E86AAC
Manual operation Manual operation
 Press upwards and hold the sunroof button  Press and hold the sunshade button upward
to tilt the sunroof to the maximum angle and to gradually open the sunshade.
stop; press and hold the button again to  Press and hold the sunshade button
gradually open the sunroof. downward to gradually close the sunshade.
 Press downwards and hold the sunroof  To make the sunshade stop in the mid-way,
button to gradually close the sunroof. release the button.
 To make the sunroof stop in the midway,
release the button . Automatic operation
Automatic operation  Press the sunshade button upward and then
 Press upwards and release the sunroof release it, and the sunshade will open
button to tilt the sunroof automatically to the automatically.
maximum angle and stop; press and release  Press the sunshade button downward and
the button again to automatically open the then release it, and the sunshade will close
sunroof to the proper position; press and automatically.
release the button again to open the sunroof  To make the sunshade stop in the mid-way,
automatically and completely. press the button again.
 Push downwards and release the sunroof
button to automatically close the sunroof.
 To make the sunroof stop in the midway,
press the button again.

26
⚠ Warning  At the moment when the sunroof and
 When closing the sunshade, be careful not sunshade are completely closed, the anti-
to clip other people's hands, heads and neck pinch function will not work if any object is
etc. to prevent serious personal injury. stuck.
 Do not allow children to operate the sunshade.

Delay function
⚠ Caution Within a few seconds after switching the power
Do not squeeze the sunroof sunshade with to OFF mode, the sunroof and sunshade still can
force to prevent the sunshade from falling off be operated.
or being damaged.
When parking a vehicle for a long time, it is One-click closing
suggested to close the sunroof sunshade to With the power supply in OFF mode and all the
prevent the inside decoration from being doors and the tailgate closed, press and hold the
damaged due to the inside high temperature if lock button on the key or the lock sensor on the
it is exposed to the sun for a long time. door handle to automatically close the sunroof.

Thermal protection function ⚠ Warning

Thermal protection function may be triggered Make sure that the heads, hands and necks of all
to protect the sunroof motor after repeated passengers are away from the window before
operation of the sunroof switch. At this time, closing the sunroof, and then use the one-click
the sunroof function will be temporarily disabled, closing function. Otherwise, serious injury may
and the sunroof will fail to be operated. occur.
The sunroof switch will automatically return to
normal after the motor cools down. Notice
If an obstacle between the window and the
Linkage function window frame is found during the closing of the
When the sunshade is in the close position, in window, the anti-pinch function will be
the process of opening the sunroof, the system triggered. The driver must confirm that the
will automatically adjust the opening degree of windows are completely closed before leaving.
the sunshade according to the opening of the
sunroof. Automatic sunroof closing
 When the power supply is in OFF mode, if
Anti-pinch function the rainfall and light sensor senses rain or
If the sunroof or sunshade encounters an snow, etc., the sunroof will be automatically
obstruction during the automatic closing, it will closed.
stop closing and return to a certain distance.

⚠ Warning
 Do not attempt to use any part of your body
to test the anti-pinch function.

27
 Notice If the sunroof rebounds during the closing
In case of the little rain, the sunroof may not be process, it can be forced to initialize through the
closed automatically. It must be confirmed that following operations:
the sunroof is completely closed before leaving. 1. When the sunroof rebounds, press and hold the
sunroof button immediately, and continue to
 The sunroof closes automatically when the keep pressing and holding the sunroof button
speed exceeds 120 km/h for more than 3 s after the rebound is over, until the sunroof is
during driving. completely closed and jitters once, and then
release the button.
Notice 2. Press and hold the sunroof button again
 If the vehicle speed drops below 120 km/h within 5 seconds until the sunroof completes
within 3 s, the sunroof will not be closed the movement from being open to fully
automatically. closed, then release the button, and the
 If the vehicle speed exceeds 120 km/h sunroof initialization is completed.
during sunroof operation, the sunroof will
remain in its original state of operation and If the sunshade rebounds during the closing
will not trigger the automatic sunroof process, it can be forced to initialize through the
closing function. following operations:
 If the sunroof switch is operated during 1. First close the sunroof completely.
automatic sunroof closing, the automatic 2. When the sunroof rebounds, press and hold the
sunroof closing function will be interrupted. sunroof button immediately, and continue to
 If the automatic sunroof closing function keep pressing and holding the sunroof button
has been triggered or interrupted while after the rebound is over, until the sunroof is
driving, the vehicle must accelerate again completely closed and jitters once, and then
from a standstill to over 120 km/h for more release the button.
than 3 s before the automatic sunroof 3. Press and hold the sunroof button again within
closing function can be triggered again. 5 seconds until the sunroof completes the
movement from being open to fully closed,
then release the button, and the sunroof
Initialization
initialization is completed.
If the system is in disorder, it can be recovered
through the following operations:
1. Close the sunroof and sunshade
completely, press and hold the sunroof
button until the sunroof and the sunshade
jitter and then release the button.
2. Press and hold the sunroof button again
within 5 seconds until the sunroof and
sunshade complete the movement from
being open to full closed, then release the
button, and the initialization is complete.

28
Refuelling

Vehicle equipment Making and answering phone calls are forbidden.

Please note that this manual contains all the Adhere to all precautions posted at the gas
standard equipment, country-specific equipment station.
and special equipment for this model series.
⚠ CAUTION
Thus, some equipment or features described in
this manual may not be installed onto your  Do not fill too much fuel. It is recommended
vehicle or are only available in some markets. For that you stop at the first automatic stop of
specific configuration information, please refer the filling gun. Otherwise, fuel can easily
to relevant sales materials or consult your enter into the carbon canister which could
vehicle dealer. shorten its service life.
 Do not allow fuel to splash on the vehicle
Refueling method while refueling, as this may corrode the
1. When the driver side door is unlocked, press painted surfaces.
the end of the fuel tank door near the rear of  Use only designated fuels.
the vehicle, to open the fuel tank door
slightly. 3. After refueling, put the fuel tank cap back to its
2. Turn the fuel tank cap counterclockwise to original position and rotate it clockwise until a
open it, and fix the cable of the fuel tank cap "click" sound is heard, indicating that the fuel
on the fuel tank door to avoid soiling the tank cap has been installed in place.
vehicle body.
Notice
The fuel tank cap should be installed properly,
otherwise the engine fault indicator may be
turned on.

4. Close the fuel tank door.

Fuel information
Item Data

EF17758C245F Fuel specification E10/E20)

Fuel tank capacity [L]

⚠ Warning 55±1.05
(reference value)
 When loosening the fuel cap, do not continue
if you hear a whooshing sound. Once the
sound disappears, you can open it slowly.
In hot weather, high-pressure fuel may be
sprayed from the tank port due to large
internal pressure, resulting in personal injury.
 Take note of such matters during refueling:
The engine must be shutdown.
No smoking or naked flames are allowed in
the vicinity of the vehicle.

29
Engine hood

Vehicle equipment 3. Take the strut out of the bracket and insert
Please note that this manual contains all the the front end into the recess in the hood to prop
standard equipment, country-specific equipment it up.
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets. For
specific configuration information, please refer
to relevant sales materials or consult your
vehicle dealer.

Opening
1. Pull the hood handle located below the
instrument panel. The hood will pop open gently. 740C295434FF

NOTICE
When the driving system of the vehicle is ready
(the indicator READY in the combination
instrument lights up) the engine will be started
automatically with shutdown prohibited after
the compartment cover is opened.
Close
1. Lift the hood up slightly.
2. Remove the strut and return the hood to its
5B39588D8B2A original position.
3. Release the engine hood at a height of about
2. Lift the engine hood slightly. Put your hand
30 cm from the engine hood lock and allow
into the gap and pull the latch of engine hood
the hood to descend without aid.
in the direction of the arrow to open the engine
4. Make sure the engine hood is fully locked.
hood.

⚠ WARNING
Make sure that the engine hood is fully closed
and secured prior to driving. Otherwise it may
open unexpectedly during vehicle running that
leads to accident.

⚠ Caution
Before closing the engine hood, make sure
that there is no debris left inside the engine
500A82FA9C93
compartment.

30
Seat

 To raise the headrest, directly pull it upwards

Vehicle equipment
to the desired position.
Please note that this manual contains all the
 To lower the headrest, press down on the
standard equipment, country-specific equipment
headrest while pressing and holding the
and special equipment for this model series.
headrest adjust button until the headrest
Thus, some equipment or features described in
reaches the desired position.
this manual may not be installed onto your
vehicle or are only available in some markets. For
specific configuration information, please refer Notice
to relevant sales materials or consult your The lowest position of the headrest is not its
vehicle dealer. use position. The headrest must be ascended to
the locked position before use.
Headrest
Headrest adjustment
Notice
When the headrest center height is aligned
After adjusting the headrest, press the headrest
with the top of the driver's or passenger's ears,
to make sure it is locked firmly.
it is at maximum efficiency.

Remove headrest
⚠ Warning
Front seat headrest
It is forbidden to adjust the headrest during
driving.

Front seat headrest

A91ABD45C88F
After raising the headrest, one person uses two
thin screwdrivers to press the keyhole while the
other person can pull the headrest upward.
FED3BD68F29E If necessary, adjust the seat backrest so that
Rear seat headrest the headrest can be removed.

Rear seat headrest

To remove the headrest, press and hold the
headrest adjust button, and remove the headrest.
If necessary, adjust the seat backrest so that
the headrest can be removed.

E1623383F02D

31
⚠ Caution Slide the seat back and forth to the required
After the headrest is installed, push it up or position, and release the adjustment lever.
down to make sure that it has been locked in
place. Notice
After adjusting the seat, make sure that it is locked
⚠ Warning firmly.
It is forbidden to drive without the headrest.
Otherwise, if there is a collision, Backrest inclination angle adjustment
your neck will be greatly impacted, resulting
in serious injury and even death.

Front seat
Manual seat adjustment
⚠ Warning
 Never adjust the seat when driving.
 Before driving, please adjust the seat to a
position convenient for correct driving.
Otherwise, it may easily cause incorrect 90ABBE946192

operations and may even lead to accidents, Move your body tightly against the backrest,
and the safety efficiency of seat belts, pull up the inclination adjustment handle of the
seat backrest, lean back to adjust the backrest
airbags, headrest and other devices cannot
to the required angle, and release the
be effectively used.
adjustment handle.
 Do not tilt the seat backrest excessively
because your body may slip out of the
⚠ Caution
safety belt during collision. The seat belts
Please ascend the backrest inclination adjustment
can provide the best protection only when handle completely before adjusting the backrest.
you sit up straight and lean against the seat Otherwise, the seat may be subject to mechanical
backrest. failures.

Forwards/backwards adjustment of the seats Seat height adjustment

0A3A8DB18BA7 995EE0679287
Pull up the seat position adjustment lever,

32
 To ascend the seat, repeatedly pull up the Notice
seat height adjustment handle. Some functions only apply to the driver's seat.
 To descend the seat, repeatedly press down
the seat height adjustment handle. Driver seat ventilation function
Touch the icon button at the bottom
Notice of the air-conditioning setting interface to set
Some functions only apply to the driver's seat. the ventilation functions of the seat.

Power seat adjustment Rear seats

⚠ Warning Rear seat adjustment
 Never adjust the seat when driving. Backrest folding
 Before driving, please adjust the seat to a After the rear seat backrest is folded, larger
position convenient for correct driving. storage space can be obtained. The left or right
Otherwise, it may easily cause incorrect part of the backrest can be folded separately.
operations and may even lead to accidents,
and the safety efficiency of seat belts, Notice
airbags, headrest and other devices cannot  Before folding, adjust the headrest to an
be effectively used. appropriate position to avoid interference
with the seat cushion or front seat.
 Do not tilt the seat backrest excessively
 Put the seat belt back in place to avoid
because your body may slip out of the
interference when folding the backrest.
safety belt during collision. The seat belts
can provide the best protection only when
you sit up straight and lean against the seat
backrest.

5E5D62331BE1
The unlocked backrest can be folded forwards
by pulling up the unlocking handle at the top of
5FA061C108D3 the backrest.
(A) Backrest inclination angle adjustment
(B) Seat height adjustment
(C) Forwards/backwards adjustment of the
seats

33
⚠ CAUTION
 Remove all objects from the seat before
folding the seat backrest.
 When the backrest is folded, do not put
heavy objects on it.

⚠ WARNING
 It is forbidden to adjust or fold the seat
when driving the vehicle.
 No one is allowed to sit on a folded seat
backrest or in the luggage area.
 Children are prohibited from entering the
luggage area.

Backrest restoring
1. Adjust the seat belt to prevent it from
getting caught under the seat when the
backrest is restored.
2. Pull up the backrest and return it to the
original position for use. Shake the backrest
gently from front to back to make sure that
the backrest is locked into place.

Rear armrests

87B51A25E8E3
Pull the rope outwards to lower the rear
armrests to provide elbow support for the rear
passengers and make the arms feel more
comfortable.

34
Rearview mirror

Vehicle equipment The inside rearview mirror will automatically

Please note that this manual contains all the reduce the reflection according to the light
standard equipment, country-specific equipment intensity of the headlamp of the vehicle behind.
and special equipment for this model series. Side mirrors
Thus, some equipment or features described in Outside rearview mirror adjustment
this manual may not be installed onto your
vehicle or are only available in some markets.
For specific configuration information, please
refer to relevant sales materials or consult your
vehicle dealer.

Interior rearview mirror

Manual anti-glare inside rear-view mirror

14B6FA85F9A0
(A) Original position
(B) Select the left outside rearview mirror
(C) Select the right outside rearview mirror
(D) Fold outside rearview mirror

Mirror adjustment
1. Rotate the outside rearview mirror adjustment
0BE427951FA7 knob to select the left or right outside rearview
(A) Normal position mirror.
(B) Anti-glare position 2. Turn the knob forward or backward, to the left
Toggle the handle to the rear of the vehicle to or the right, and you can adjust the left or right
switch to the anti-glare position. The reflection outside rearview mirror lens.
of the headlamp of vehicle behind can be 3. After adjustment, reset the outside rearview
reduced at that position. mirror adjustment knob to the initial position.

Automatic anti-glare inside rearview ⚠ WARNING

mirror Do not adjust the rearview mirrors while driving.
Otherwise, errors in control can lead to accidents
and serious injuries or death.

Electric folding
Turn the adjustment knob to theข outside
rearview mirror folding position and the outside
rearview mirror will be folded automatically.
Turn the adjustment knob to a different position
and the outside rearview mirror will deploy
automatically.
41251C7DDFE5

35
Manual folding

AED8A21AA2F9
Move the outside rearview mirror in the direction
indicated by the arrow and it can be folded.
It is mandatory to have the outside rearview
mirrors back in their pre-fold positions prior to
driving.

⚠ CAUTION
For electric folding outside rearview mirrors,
do not fold them manually. Otherwise, the
internal structure of the rearview mirror may
be damaged.

Auto folding when locking the vehicle

You can set rearview mirror fold mode on
multimedia display screen via [ Vehicle Setting]
→[In-Car]→ [Body] by .
When the rearview mirrors is [Auto] , it allows
you to link its folding and deploying to the
locking and unlocking of the doors.

36
Steering wheel

Vehicle equipment Horn

Please note that this manual contains all the Press the horn mark on the steering wheel or
standard equipment, country-specific equipment its surrounding area and the horn honks.
and special equipment for this model series. Thus,
some equipment or features described in this
manual may not be installed onto your vehicle or
are only available in some markets. For specific
configuration information, please refer to relevant
sales materials or consult your vehicle dealer.

How to adjust

BC934B8CAFFE
1. Release the adjustment lever beneath the
steering wheel.
2. Adjust the steering wheel to align it to your
chest and make sure you can see all the
instruments and indicators on the combination
instrument.
3. After adjusting, retract the lever back to lock
the steering wheel.

⚠ WARNING
 Adjustment of steering wheel during vehicle
running is forbidden. Otherwise, serious injury
or death may result from an accident caused
by control errors.
 You must ensure that the steering wheel is
locked firmly in place after adjusting it.
Otherwise, serious injury or death may result
from an accident caused by sudden
movement of the steering wheel.

37
Roof rails

Vehicle equipment ⚠ WARNING

Please note that this manual contains all the  Items on the roof luggage rack must be
standard equipment, country-specific equipment secured firmly in place. Otherwise, there is
and special equipment for this model series. a risk of an accident.
Thus, some equipment or features described in  Loading goods on the roof luggage rack will
this manual may not be installed onto your raise the vehicle's center of gravity. Avoid
vehicle or are only available in some markets. high speed driving, sudden startup, sharp
For further configuration information, please turns, emergency braking or abrupt
refer to relevant sales information or consult operation, as this may cause loss of control
with your distributor selling the vehicle to you. or overturn of the vehicle due to incorrect
operation of the vehicle, resulting in
Roof rack
serious injury or death.
To install a luggage rack on the roof rack,
 When rather heavy or large objects are
please read carefully the installation manual
loaded on the roof luggage rack, changes in
accessory of the luggage rack.
the vehicle's center of mass and wind resistance
may affect its driving performance, and
NOTICE
there is a risk of an accident. Therefore, you
When the luggage rack is installed or used for
must adjust your driving style and speed
carrying items, relevant requirements of local
according to the specific circumstances.
traffic regulations should be observed.
 Drive at low speed in lateral wind. The
vehicle's profile and its high center of
Roof rack bearing capacity
gravity make it more sensitive to lateral
The maximum load weight of the roof rack is
gust, and reducing the vehicle speed will
50 kg; the maximum load weight of the roof
make it easier to control.
rack is 35 kg when the vehicle is decelerating
 Do not overspeed, jolt, make sharp turns, hit
rapidly.
objects, etc. when driving offroad or in
uneven terrain. This can cause loss of
NOTICE control or overturn of the vehicle, resulting
The load weight of the roof rack includes accessories in serious injury or death, as well as serious
such as the beam and other accessories. damage to the suspension and chassis of
the vehicle.
 Do not cross steep slopes, and it is better to
drive straight up or down. The vehicle is
more likely to roll over than to roll forward
or backward.
 The roof luggage rack can only be used with
the sunroof closed. Otherwise, the roof
luggage rack or the items loaded on it may
cause injury to passengers.

38
Light Control

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.
Light setting
The light settings can be made through the multimedia display.
Type I

1874B6CB6F1F
Type II

BEE1D687FF3C
 Active Courtesy: the active courtesy function can be activated or deactivated.
Active welcome light: the active courtesy function can be activated or deactivated.
After the active courtesy function is activated and when the main lamp switch is in the AUTO
position, the position lamp and the low beam headlamp will be on for a period of time when the
door is unlocked.
 Power Saving Delay Time: the power saving delay function can be set.
After the power supply mode is switched to OFF mode, if the power supply mode, door lock and
hazard warning light switch status do not change within the set time range, the power saving
function will be automatically turned on to save power.

39
 Ceiling Lamp Delay Time: the turning on time and the delay off time of the interior lamp can be
set.
 Take Me Home Delay: the continuous lighting time of the position lamp and the low beam
headlamp can be set after the “take me home” function is triggered.
 Sports Mode Light: the sport mode light function can be activated or deactivated.
Sports mode light setting: the sport mode light function can be activated or deactivated.

⚠ CAUTION
Do not use the exterior lighting for a long time when the vehicle is not started. Otherwise, the
undervoltage battery may be caused.

40
Light control combination switch  Automatic light control can only assist the
driver. At all times the driver should be
Main lighting switch
responsible for the lighting of the vehicle.
 Turn the main lamp knob to the OFF position
to turn off all vehicle lamps.

Fog lamp switch

3927AC98287D
 Turn the main lamp knob to the width lamp
position to turn on the position lamp
and the license plate lamp.

⚠ CAUTION DD2CEF12CC39

Do not use the position light to replace the low When the low beam headlamp is illuminated,
beam headlight in the driving. Otherwise, there turn the fog lamp knob to the rear fog lamp
is a risk of an accident. position repeatedly to turn the rear fog
lamp on or off. When released, the knob will
The position lights are not bright enough to automatically return.
illuminate the road in front of the vehicle or
allow other vehicles and pedestrians to see the Turn signal and lane change signal
vehicle. Therefore, turn on the low beam
headlight when the weather is dim or visibility
is poor.

 Turn the main lamp knob to the low beam

headlamp position to turn on the low
beam headlamp and keep the position lamp
and the license plate lamp illuminated.
 Turn the knob of the main lamp knob to the
AUTO position. The width lamps and low
DB397E53DFCA
beam headlamps will be turned on or off
(A) Lane change signal
automatically according to the brightness of
(B) Turn signal
the surrounding environment.
 Lane change signal: Pull up or push down the
light control combination switch gently and
⚠ CAUTION
release it, then the light control combination
 When visibility is affected in the day due to
switch will return automatically and the
fog, the lights may not light up automatically.
corresponding turn signal lamp will flash 3
Please turn on the lights manually in this
times.
case.

41
  Turn signal: Pull up or push down the light period of time after all the doors and the
control combination switch and release it, tailgate have been successfully locked from
then the light control combination switch the outside of the vehicle (except for locking
will not return automatically and the by the mechanical key) to ensure that you can
corresponding turn signal lamp will flash leave the vehicle in the dark.
continuously.
Daytime running lamps (DRL)
High/low beam manual switch To allow other drivers to see your vehicle more
clearly, the daytime running lamps
automatically light up when the vehicle is
started. The daytime running lamps will go out
when the following conditions are triggered
 When the headlamp is turned on.
 When the left or right turn signal lamp is on,
the daytime running lamp

⚠ WARNING
The daytime running lamps are not designed
44B9EE7AB515
for the needs of night-time driving.
(A) High beam headlamp on
(B) High beam headlamp flashes
 When the low beam headlamp is on, press Emergency braking warning
the light control combination switch in a When the speed of the vehicle exceeds 50
direction away from the steering wheel to km/h, the turn signal lamp will flash if you
turn on or off the high beam headlamp; when perform emergency braking at that time.
you release the light control combination
switch, it returns automatically. Emergency hazard flashers
 The high beam headlamp turns on when you
pull the light control combination switch up
in a direction close to the steering wheel;
when released, the light control combination
switch automatically returns and the high
beam headlamp goes out. You can repeat
this operation to make high beam headlamp
flash.

Follow me home function

BBCBB74943DE
With the power supply in OFF mode and the
In the event of vehicle failure or traffic accident,
main lamp switch in the automatic light
turn on the emergency flashers to warn other
position, if the current light intensity meets the
vehicles.
conditions for the low beam headlamp to be on,
Press the switch to turn on or turn off the
the position lamp and the low beam headlamp
emergency flashers.
will automatically illuminate for a

42
Light height adjustment Interior lights
Reading lamps
⚠ CAUTION
Do not use the interior lamps for a long time
when the vehicle is not started.
Otherwise, it may lead to drain battery.

C45DF1F3D6AF
The headlight beam height is adjusted according to
the number of passengers and the load of the
vehicle.
 Turn the knob upwards to raise the height of
the headlight beam.
 Turn the knob downwards to lower the height
62BFEC4C6806
of the headlight beam.  Press the reading lamp main switch to
turn on or turn off the reading lamps.
Instrument brightness adjustment  Press the door-control function
enabled, the reading lamp will turn on or
turn off automatically according to the door
condition.

Center roof lamp

26687162ACD7
When the position lamps are turned on, you can
adjust the brightness of the instrument and the
vehicle back lamps.
 Press the upper part of the button: the
instrument and the vehicle back lamps are AE413216A945
turned on.  Push the switch to OFF position: roof lamp off.
 Press the lower part of the button: the  Push the switch to middle position to turn
instrument and the vehicle back lamps are on the door-control function; the roof lamp
darkness. will turn on or turn off automatically
according to the door condition.
 Push the switch to ON position: roof lamp on.

43
Side roof lamp

272173CA18CF
Press the left side roof lamp switch or the
right side roof lamp switch to turn on or
turn off the corresponding roof lamp.
With the door-control function enabled, the
roof lamp will turn on or turn off automatically
according to the door condition.

Luggage-area light
When the back door is open or closed, the
luggage-area lights turn on or off automatically.

44
Wiper controls

Vehicle equipment ⚠ CAUTION

Please note that this manual contains all the  If the surface of the windshield glass is dirty or
standard equipment, country-specific equipment there are foreign objects on the windshield
and special equipment for this model series. Thus, (snow, gum, etc.), please clean it first and
some equipment or features described in this remove the foreign objects, otherwise the
manual may not be installed onto your vehicle or wiper blade or the internal structure of the
are only available in some markets. For further wiper may be damaged.
configuration information, please refer to  Prior to using the wiper in the cold season, you
relevant sales information or consult with your shall ensure to check if the wiper blade is
distributor selling the vehicle to you. frozen on the windshield glass. If the wiper
blade has been frozen on the windshield, you
should wait to use it until it has defrosted,
Electric wiper
otherwise the wiper blade and wiper motor
Front wiper
may be damaged.
Front wiper position  Should the wiper stop working due to issues
such as accumulated snow, please turn off the
wiper and park the vehicle in a safe spot. Then
remove accumulated debris so that the wiper
may continue to operate normally.

Adjustment of intermittent wiping

frequency

080E92635C27
(A) Front wiper mist operation ( MIST)
Pull the wiper control combination switch
upwards to the MIST position. Once released,
the lever will automatically return to its
original position. The front wipers will
operate once.
(B) Turn off front wiper (OFF)
EB24582437CE
(C) Intermittent wipe (INT)
Turn the adjustment knob to change the
(D) Low speed (LO)
intermittent time in order to adjust the wiping
(E) High speed (HI)
frequency of the front wiper at the intermittent
wiping position.

45
Washing function Rear wiper

46A82A16B535
930465496923
Pull the wiper control combination switch up  Turn the rear wiper control knob to the ON
vertical to the steering wheel. position and the rear wiper will turn on.
The front wiper will clean the front windshield  Turn the rear wiper control knob to the rear
with windshield washer fluid. windscreen cleaning position and hold.
The rear wiper will wipe the rear windscreen
using screen washer. Release the control
⚠ CAUTION
knob and it will return automatically to its
 Avoid prolonged use of the washer. Otherwise
previous position.
it may damage the washing motor.
 Turn the rear wiper control knob to the OFF
 To protect the washing motor, the washer
position to turn off the rear wiper.
may automatically shut down after a period
of continuous operation.
 Always check the liquid level of the washer ⚠ CAUTION
fluid tank and add it in time. In the cold  Do not use products that can produce coatings
season, add the appropriate washing fluid to on the windscreen (e.g. cleaning solutions for
ensure that the washing fluid does not freeze. crystal plating or coating, glass coatings, etc.).
Otherwise, the washer will not only lose the Otherwise, abnormal vibration and noise may
washing function, but also freeze the relevant occur during scraping by the wiper.
parts.  Do not let the wiper blade come into contact
with products such as oil-based cleaning
agents, otherwise a chemical reaction will
occur, resulting in serious deformation of
the wiper blade.

46
Automatic wiper  If the wiper get stuck for any reasons, such as
Front wiper snow, please turn off the wiper and park the
vehicle at a safe location as soon as possible.
Front wiper position
Then remove anything that is preventing the
wipers from wiping so that the wiper can
work normally.

Adjustment of auto wiping frequency

275CCCA3323B
(A) Front wiper mist operation (MIST)
Pull the wiper control combination switch
upwards to the MIST position.
Once released, the lever will automatically
return to its original position. The front 4C411A8EFC4D

wipers will operate once. Turn the rotation adjustment knob to change
(B) Turn off front wiper (OFF) the sensitivity settings for the rainfall and light
(C) Intermittent wipe (INT) sensor in order to adjust the wiping frequency
(D) Low speed (LO) of the front wiper at the auto wiping position.
(E) High speed (HI)
⚠ WARNING
 The rainfall and light sensor is unable to
⚠ CAUTION
recognize all precipitation to activate the
 If the windscreen is dirty or has any foreign
front wiper. If rain on the windscreen affects
object stuck to it (such as snow or tree sap
the line of sight, you shall manually adjust the
and so on), please clean off and remove the
front wiper gear or wiper frequency timely as
foreign object before use to avoid damaging
required.
the blade and the internal structure of the
 When the automatic front wiper is in the
wiper.
AUTO position, the front wiper may operate
 Before using the wipers in the cold season,
unexpectedly if it touches the windscreen
you shall check whether the wiper blade is
near the inside rearview mirror from outside
frozen to the windscreen. If the wiper blades
the vehicle or the windscreen glass is
are frozen to the windscreen, make sure to
vibrated. Be careful not to grip your fingers or
defrost them before use to avoid damaging
other parts by the front wiper.
the blade and wiper motor.
 Do not place the automatic front wiper in the
AUTO position when you wash the car or no
front wiper is required to be used. Otherwise,
the front wiper may operate unexpectedly.

47
 ⚠ CAUTION  When the washer fluid is insufficient, please
 If the windscreen near the interior rearview replenish it. In cold seasons, appropriate
mirror is dirty or has any foreign object washer fluid shall be added to ensure that the
stuck to it (such as snow or tree sap and so washer fluid does not freeze. Otherwise, the
on), please clean off and remove the foreign washer will not only lose the washing
object before use to avoid damaging the function, but also freeze the relevant parts.
blade and the internal structure of the wiper.  Do not use the product which can produce
 Even if snowflakes come in contact with the cladding on the windscreen (for example, the
rainfall and light sensor, the sensor may not screen wash contains plated crystal or coating
operate normally and the front wipers may film, glass coating and so on). Otherwise, the
not function, as snowflakes come in different wiper may bounce and make abnormal
shapes. The snow melted may cause the sounds when wiping.
front wiper to automatically brush.  The blade cannot get contact with oily
cleaning agent. They may react chemically
Washing function which cause the blade deformed.

Rear wiper

930465496923
Pull up and hold the wiper control combination
switch towards the steering wheel, then the front 2603A334FC8A
wipers will use windscreen washer fluid to wipe  Turn the rear wiper control knob to the ON
the front windscreen. When released, the position and the rear wiper will turn on.
combination switch will return automatically.  Turn the rear wiper control knob to the rear
windscreen cleaning position and hold.
⚠ CAUTION The rear wiper will wipe the rear windscreen
 Avoid using the washer for a long time. using screen washer. Release the control
Otherwise it may damage the washing knob and it will return automatically to its
motor. To protect the washing motor, the previous position.
washer may automatically shut down after a  Turn the rear wiper control knob to the OFF
period of continuous operation. position to turn off the rear wiper.
 When the washer fluid is insufficient, please
replenish it. In cold seasons, appropriate
washer fluid shall be added to ensure that
the washer fluid does not freeze. Otherwise,
the washer will not only lose the washing
function, but also freeze the relevant parts.

48
⚠ CAUTION
 Do not use the product which can produce
cladding on the windscreen (for example,
the screenwash contains plated crystal or
coating film, glass coating and so on).
Otherwise, the wiper may bounce and
make abnormal sounds when wiping.

 The blade cannot get contact with oily

cleaning agent. They may react chemically
which cause the blade deformed.

Front wiper and washer settings

The interval from the time when the washer
function is activated to the time when the
front wiper starts to wipe can be set via
[Vehicle Settings]→ [In-Car] → [ Body]→[ Front
Working Interval] /[Front wiper interval] on the
multimedia display screen.

49
Air conditioning system

Vehicle equipment NOTICE

Please note that this manual contains all the  Normally, you should put the system in
standard equipment, country-specific equipment and external circulation mode. Use of internal
special equipment for this model series. Thus, some circulation mode tends to cause foggy
equipment or features described in this manual may windows, especially when the compressor
not be installed onto your vehicle or are only is turned off.
available in some markets. For further configuration  The internal circulation mode should be
information, please refer to relevant sales used under various circumstances such as
information or consult with your distributor selling driving inside a tunnel or in the traffic jam,
the vehicle to you. dirty air outside the vehicle or quick
cooling and heating is desired.
Air conditioning control panel
Button control type  Press the front defroster button to
enable/disable the front defroster function.
The corresponding indicator lights up,
suggesting that the front defroster function
has been enabled, and the frosting and
fogging of the front windshield and the side
door glass can be gradually eliminated.
 Press the rear window defroster button
to enable/disable the rear window defroster
function. The corresponding indicator lights
up, indicating that the rear window
2D0D9945C5A5
defroster has been turned on. At this time,
 Press ON/OFF to turn on or turn off the air- you can gradually relieve the frosting of the
conditioning system. rear window.
 Press A/C button to activate or deactivate the The rear window defrosting function will
cooling mode. The corresponding indicator turn off automatically after it has been
illuminates, indicating that the cooling mode is turned on for a period of time, and the
activated. In this mode, the inside temperature corresponding indicator will go out.
and humidity may be reduced.
 Press the internal circulation button to ⚠ WARNING
switch between the internal circulation and Once the rear window defrosting function has
external circulation modes. been enabled, the rear windshield will
The corresponding indicator lights up, indicating become hot. Do not touch it to avoid burns.
that the internal circulation mode has been
turned on.
The corresponding indicator is extinguished,
indicating that the external circulation mode
has been turned on. In this case, the air outside
the vehicle can be introduced into the vehicle.

50
⚠ CAUTION  The internal circulation mode should be
When the vehicle is not started, please do not used under various circumstances such as
use the rear window defrosting function for a driving inside tunnel or in the traffic jam,
long time, so as to prevent the battery power dirty air outside the vehicle or quick
from being drained. cooling and heating is desired.

Touch control type  Touch the front defroster button

to enable/disable the front defroster
function. The corresponding indicator
lights up, suggesting that the front
defroster function has been enabled, and
the frosting and fogging of the front
windshield and the side door glass can be
gradually eliminated.

 Touch the rear window defroster

button to enable/disable the rear window
233A31854529 defroster function. The corresponding
 Tap ON/OFF to turn on or turn off the air indicator lights up, indicating that the rear
conditioning system. window defroster has been turned on. At this
 Tap A/C button to activate or deactivate the time, you can gradually relieve the frosting of
cooling mode. The corresponding indicator the rear window.
illuminates, indicating that the cooling mode is The rear window defrosting function will
activated. In this mode, the inside temperature turn off automatically after it has been
and humidity may be reduced. turned on for a period of time, and the
 Tap the internal circulation button to switch corresponding indicator will go out.
between the internal circulation and external
circulation modes. The corresponding indicator
⚠ WARNING
lights up, indicating that the internal circulation
Once the rear window defrosting function has
mode has been turned on.
been enabled, the rear windshield will
The corresponding indicator is extinguished,
become hot. Do not touch it to avoid burns.
indicating that the external circulation mode has
been turned on. In this case, the air outside the
⚠ CAUTION
vehicle can be introduced into the vehicle.
When the vehicle is not started, please do not
use the rear window defrosting function for a
NOTICE
long time, so as to prevent the battery power
 Normally, you should put the system in external
from being drained.
circulation mode. Use of internal circulation
mode tends to cause foggy windows, especially
when the compressor is turned off.

51
 A/C setting interface
NOTICE
 The multimedia display interface and its operation may vary with the model configurations. Refer
to the actual vehicle.
 The air conditioning system consumes the power battery when it is working, reducing the driving
range.
 Under extreme operating conditions (e.g. high or low ambient temperatures, longtime slope
climbing, etc.), the air conditioning may be limited in its power or even stop working in order to
ensure the vehicle power performance.

Type I

98744953B64F
Type II

A35D9205BE9E
 Touch the internal circulation button or the external circulation button to make the A/C
system switch between the internal and external circulation modes.
 The internal circulation indicator light goes on, indicating that the internal circulation mode
has been turned on.
 The external circulation indicator light goes on, indicating that the external circulation mode has
been turned on. In this case, the air outside the vehicle can be introduced into the vehicle.

52
 NOTICE
 Normally, the external circulation mode should be used. Using the internal circulation mode tends
to cause windows to fog, especially when the compressor is turned off.
 The internal circulation mode should be used under such circumstances as the tunnel, traffic jam,
dirty air outside the vehicle or quick cooling and heating desired.

 Touch the A/C button to enable or disable the cooling mode. The corresponding indicator light
turns on, indicating that the cooling mode is activated. In this mode, the interior temperature and
humidity may be reduced.
 Touch the AUTO button to activate the automatic mode. In this mode, the airflow distribution
mode and the airflow can be automatically adjusted to reach the set temperature.
NOTICE
If you are not satisfied with the automatic adjustments, you can manually make adjustments. In this
case, the automatic mode will exit and the indicator light will be off.

 Touch the OFF button turn off the air conditioning system.
Touch the OFF button to turn off the air conditioning system.
 Touch the face-blowing mode button the feet and face-blowing mode button the feet-
blowing mode button or the feet-blowing and defroster mode button to select the
corresponding airflow distribution mode.
 Touch or slide the temperature display area on the air conditioning setting interface to adjust the
temperature.
 Touch the rear defroster button to activate or deactivate the rear defroster function. The
corresponding indicator light goes on, indicating that the rear defroster function has been enabled.
In this case, the frosting of the rear windscreen can be gradually eliminated.
The rear defroster function will automatically switch off after a period of time and the corresponding
indicator light will go out.

⚠ WARNING
Once the rear defroster function is on, the rear windscreen will become hot. Do not touch it, and take
care to avoid getting burnt.

⚠ CAUTION
When the vehicle is not started, do not use the rear defroster function for a long time, so as to prevent
the undervoltage battery.

 Touch the front defroster button to activate or deactivate the front defroster function. The
corresponding indicator light goes on, indicating that the front defroster function has been
enabled. In this case, the frosting and fogging of the front windscreen and the side door glass can
be gradually eliminated.
 Touch the air flow button to show the air flow adjustment panel. The air flow can be
adjusted by touching or sliding at the area on the air flow adjustment panel.

53
  Touch the synchronization or disconnect button to enable or disable the zone control mode.
When the synchronization indicator light goes on, the zone control mode has been turned off.
In this case, the front passenger side air conditioning temperature remains the same as the driver
side air conditioning temperature. Also, when the driver side air conditioning temperature is
adjusted, the front passenger side air conditioning temperature is adjusted simultaneously.
 When the disconnect indicator light goes on, the zone control mode has been turned on. In this
case, when the driver side air conditioning temperature is adjusted, the front passenger side air
conditioning temperature is not affected. When the front passenger side air conditioning
temperature is adjusted, the zone control mode is automatically turned on.
 Touch the more A/C settings button to show more air conditioning settings interface.

A/C setting
On the A/C setting interface, tap the button to pop up the A/C function setting interface.

3943CBB07AC1
[A/C comfort curve] : set the comfort effect of the A/C system in AUTO mode.
 Economy: the cooling or heating effect of the A/C system is softer with smaller air volume compared
with the standard mode.
 Standard: the A/C system automatically controls the outlet temperature and air volume according to
the temperature set by the user.
 Powerful: the cooling or heating effect of the A/C system is stronger with larger air volume compared
with the standard mode.

54
Air conditioning control 2. You can also adjust the airflow or the
Cooling/heating temperature, turn on or off the compressor,
After starting the vehicle: or switch between the internal and external
1. Select the [ AUTO ] mode and the circulation modes on demand.
corresponding indicator light will turn on. At
this moment, the compressor will NOTICE
automatically turn on or off depending on It is recommended to switch to the external
the temperature and the environment. circulation mode if interior air is heavily polluted
2. Set the temperature to your desired value. or the interior is fogged up.
The A/C system will automatically adjust
the air distribution mode and the airflow to ⚠ CAUTION
achieve the set temperature.
 Check the radiator and the air conditioning
3. Selecting the internal circulation mode may
condenser on a regular basis. Use a low-
speed up cooling or heating and help to
pressure water gun or a soft brush to remove
improve the economy and comfort of the
the leaves, insects and dust from their front
vehicle.
surfaces. Otherwise, these objects will block
the air flow, thereby reducing the cooling
NOTICE
effect.
 When the vehicle is exposed to the burning  Running the air conditioning regularly keeps
sun for a long time, the temperature in the the compressor and seals well lubricated and
vehicle will be very high. In this case, if you prevents leakage. Therefore, even in the cold
need to drive the vehicle, you are season when air conditioning is not required,
recommended to lower all the windows for it is necessary to run the air conditioning at
ventilation and then enable the air least once a week for more than 10 minutes
conditioning cooling mode. After the heat in each time.
the vehicle is dissipated, raise all the  If the A/C system does not cool as well as
windows. before, head to the authorised service centre
 After the air conditioning temperature is set, for maintenance.
the air conditioning system will  Direct discharge of refrigerant into the
automatically control the working state of atmosphere is harmful to the environment
the cooling system and the heating system and the refrigerant should be recovered by
according to the interior and exterior the trained and certified technicians using
ambient temperature. appropriate containers.
After the air conditioning system is turned
on in the cold season, the heating system
NOTICE
needs to warm up for a period of time before
About the air conditioning odour
it can work normally. Before the heating
 Source of odour
system finishes the warming up, the air
Internal and external air exchange should be
conditioning system may not distribute
warm air, and its airflow is small. This is carried out for air conditioning as its long-
normal. term use may gather dirt which will go
mouldy after a long time, resulting in odour.
Front defroster/front defogger The air conditioning filter will accumulate
After starting the vehicle : water vapour, dust, etc. after use for a long
1. Select the front defroster mode, and the time, resulting in odour.
corresponding indicator light will turn on.

55
 Suggestions Rear vent
When the outside air is fresh, the external
circulation mode is recommended for use to
keep the interior air circulating.
When the vehicle is in cooling mode, you are
recommended to turn off the [ A/C ] switch first
and let the air conditioning continue running for
about 3 to 5 minutes before turning off the air
conditioning system. This will dry off the air
conditioning evaporator and the air
conditioning system to prevent mould growth
and reduce odours. 2D16855FBB72

When you smell a foul odour, you are By turning the slats at the center of the vent,
recommended to head to the authorized adjust the direction of air flow.
service centre for check. Clean or replace the air Slide the slats as indicated by the left-to-close
conditioning filter element, if necessary. marking or right-to-close marking
to the limit position to close the air vent.
A/C Vent
Front vents

C29A0AC0685A
By turning the slats at the center of the vent,
adjust the direction of air flow.
Slide the slats as indicated by the left-to-close
marking or right-to-close marking
to the limit position to close the air vent.

56
Mobile phone wireless charging

Vehicle equipment  After turning on the wireless charging reminding

function of mobile phone, a voice prompt can be
Please note that this manual contains all the
issued when the charging status changes.
standard equipment, country-specific equipment
and special equipment for this model series. Thus,
some equipment or features described in this NOTICE
manual may not be installed onto your vehicle or  This function is not applicable to all mobile
are only available in some markets. For further phones, but only to mobile phones that have
configuration information, please refer to relevant passed the "Qi" official standard certification
sales information or consult with your distributor and can be normally placed in the charging
selling the vehicle to you. area.
 Only one mobile phone can be charged at a
Instruction time.
The wireless charging function can be turned  On bumpy roads, intermittent stopping and
on or turned off via [Vehicle Settings][ In- resuming of wireless charging may occur. If
Car][ Wireless Charger] on the multimedia the mobile phone deviates from the charging
display screen. area and the charging stops, move the
mobile phone back to the chargeable area.
 It is normal that wireless charging devices
and mobile phones will get hot during
charging.
When the temperature is too high, the system
will stop charging, and will continue charging
D0AADCF605A7
after the temperature drops.
After turning on the wireless charging function of
 If the mobile phone is faulty, this may also
mobile phone, make sure that the doors are
cause it to fail to be charged. Other mobile
closed, switch to the power supply mode ON or
phones that meet the requirements can be
start the vehicle. Then the mobile phone placed
used for wireless charging detection to
in the charging area can be charged.
confirm whether the mobile phone is faulty.
 If the mobile phone is equipped with a
protective cover or an accessory that does
not support wireless charging, it should be
removed first; otherwise, the phone cannot
be charged normally.
 To prevent the undervoltage battery, do not
use the wireless charging function for a long
time when the vehicle is not started.

6CAFE4E5E636

NOTICE
In order to achieve a better charging effect, ensure
that the charging coil of the mobile phone is facing
downwards.

57
⚠ WARNING
 For the sake of safety, drivers should not
perform charging related operations during
driving.
 Do not place coins, keys, chip cards and other
metal objects in the charging area. Otherwise,
metal objects may be heated, which may lead to
abnormal charging or safety accidents.
If metal foreign objects are found in the
charging area during charging, do not
remove them by hand to avoid scalding your
fingers. You should turn off the wireless
charging function immediately, and wait a
few minutes before removing foreign
objects.
 If you need to use the charging area as a
storage case, turn off the wireless charging
function.

⚠ CAUTION
 Do not spray any liquid at the charging area,
so as to avoid the liquid seeping into the
wireless charging system through the
clearance of rubber mad, which may lead to
system failure.
 Do not modify the wireless charging system to
avoid damage to the vehicle or accidents.

NOTICE
This device conforms to standards or technical
requirements of NBTC.

58
Interior equipment

Vehicle equipment Vanity mirror

Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series. Thus,
some equipment or features described in this
manual may not be installed onto your vehicle or
are only available in some markets. For further
configuration information, please refer to
relevant sales information or consult with your
distributor selling the vehicle to you.
Sun visor
51777FC8915A
A vanity mirror is set inside the sun visor. Open the
cover and use it.
Please close the lid when not using the vanity mirror.

Storage box

38F95C98BECD
To block sunlight from straight ahead, flip down
the sun visor.

1912CCA13F51
Pull the handle on the storage box and flip down to
open it.
Flip the storage box up until the lock is in place and
then close it.

⚠ WARNING
EE7A67445D9C Make sure the storage box is closed when driving.
To block sunlight coming in from the side, flip Otherwise, such items may be dislodged from the
down the sun visor, unhook it and push it to the storage box and lead to an injury in the case of an
side. accident or emergency braking.

59
Storage case Front cup holder

02FA26A0FFDD
58DA9A649F90
Pull up the open handle on the storage case
Press and release the front cup holder cover. Open
and flip up to open it.
the cup holder cover slightly to use the cup holder.

Spectacle case ⚠ CAUTION

 Don't place small or unstable beverage cans
in the cup holders, or they may tip over.
 Make sure that the lid of the beverage can is
covered to avoid spilling liquid.

Rear cup holders

02E02E3D9CF9
Press the spectacle case to open it.
When placing glasses, fold the two mirror legs
normally, with the lens facing forward and the
mirror leg facing upward.
Otherwise, the glasses may fall off when opening
the glasses case.
4F3CB3866BC8

⚠ WARNING Tilt the rear seat armrests to the lowest position

Make sure the spectacle case has been to use.
closed when driving.
⚠ CAUTION
NOTICE  Don't place small or unstable beverage cans
Certain oversized sunglasses models may not in the cup holders, or they may tip over.
fit into this case.  Make sure that the lid of the beverage can is
covered to avoid spilling liquid.

60
Bottle holder
There is a bottle holder on the inside of each
front door, which is only used for placing the
sealed bottle container.
⚠ WARNING
Do not place anything other than bottles inside
the bottle holder. Otherwise, in the case of an
accident or emergency braking, such items may
be dislodged from the bottle holder and lead to
an injury. A45CFE3BD469
When the power supply mode is in ON mode, just
⚠ CAUTION open the cover to use it.
Make sure that the lid of the bottle is covered This power supply can provide a 12 V DC power for
to avoid spilling liquid. accessories with rated power less than or equal to
120 W (10 A).
Power supply socket
USB power supply socket Driving recorder power supply

AAC251107CED C7102FC3177F
It is located beside the rear air conditioning outlet. It is located near the interior rearview mirror.
When the power supply mode is in ON mode, just The power supply can be used when the power
open the cover to use it. supply mode is in the ON mode.
This power supply can be used to charge the This power supply is designed to provide a 5 V DC
devices such as mobile phones and tablets. power supply for driving recorders whose rated
power is less than or equal to 10 W.
Standby power supply
NOTICE ⚠ WARNING
Due to different vehicle configurations, standby  For driving safety, be careful not to block the
power supply of some models may be installed line of sight to prevent danger when installing
in the hollow place on the left side of the a driving recorder.
auxiliary instrument panel. Please refer to the  Flammable gases and heaters must be kept
actual vehicle. away from the power supply socket.

61
⚠ CAUTION
 Do not allow liquids such as beverages or
foreign objects to enter the power supply
socket. Otherwise, the faults like short circuits
may be caused. If the power supply socket has a
cover, close the cover when it is not in use.
 If you use an accessory that exceeds the rated
power, the vehicle fuse may be burnt out.
 Do not connect precision devices, highly
sensitive equipment or other important
equipment to this power supply socket.
 Do not use this power supply in humid and
high-temperature environments.
 Never use it in parallel or in series with any
other power supply.
 If you find any abnormal condition (e.g.
unusually high temperatures, smoke,
oduors, etc.) during use, please stop using
immediately and contact the authorized
service centre for inspection and repair.
 Modifying or repairing this power supply
system without authorization is forbidden.
 The external wiring harness should be
waterproof and sealed.

62
2 Driving
Driving procedures 64
Advice on driving in harsh environments 68
Advice on driving during run-in 72
Hybrid vehicles 73
Power supply mode 76
Starting and shutting down vehicle 77
Parking brake 79
Automatic transmission 81
Driving mode 84
Single pedal function 85
Vehicle wash/trailer mode 87
Fording mode 88
Steering wheel assist mode 89
Parking assist system........... 91
Tyre pressure monitoring system 98
Fatigue driving reminder system 99
Cruise control system 100
Cruise control assist system 102
Intelligent driving assist system 107
Hill descent control system 117
Driving assist system 118
Emission control system 120
Head-up display (HUD) 122
Virtual instrument 123
Indicator lights on the instrument 128
Power supply management system 134

63
Driving procedures

not only obstructs the driver's view, but also affect

Vehicle equipment
the starting and safe driving, which may lead to an
Please note that this manual contains all the
accident.
standard equipment, country-specific equipment
and special equipment for this model series.
The driver's feet space
Thus, some equipment or features described
Do not place any item at the feet of the driver.
in this manual may not be installed onto your
Items placed at the driver's feet may be trapped
vehicle or are only available in some markets.
under pedals, causing the driver to lose control of
For further configuration information, please
the vehicle, or leading to an accident.
refer to relevant sales information or consult
If you want to use a floor mat, please choose an
with your distributor selling the vehicle to you.
appropriate floor mat. If the selected floor mat
shape and its layout position are inappropriate or
Before driving
if floor mats are double stacked, brake pedal
Removing miscellaneous items
performance may be affected. As a result, the
Remove the snow and fallen leaves, etc.
vehicle may not be started, it's difficult or unable
accumulated on the vehicle before driving.
to change gears or even lead to a higher risk of
other accidents.
Check vehicle conditions
Please check daily items such as tyres, fluid,
Under the seat
light and body appearance before driving in
Do not place any item under the seats. Items
order to ensure you have a safe and pleasant
placed under the seat will make it difficult to
driving experience.
adjust the seat position or lock the seat in
If you believe that your vehicle requires
place, which could easily lead to an accident.
maintenance or repair, please get in touch with
your authorised service centre in a timely manner.
Seat backrest
Do not place cushions and other items between
Confirm that the vehicle doors and the
the seat backrest and the back of the human
engine hood are closed
body as it might affect the driving posture.
Before driving, make sure all vehicle doors are
Besides, in the event of a vehicle collision, the
closed. If a vehicle door has not been closed
effectiveness of seat belts and head restraints
properly, it may open unexpectedly during the
will not be realized to the full, which may result
driving and cause an accident.
in serious life-threatening injuries.
Before driving, if you have opened up the engine
hood, check that the hood has been locked
On the window glass
down. If the engine hood has not been secured
Do not attach items such as decorative items
and locked properly, it may fly open during
using vacuum suction cups on vehicle windows.
driving and cause an accident.
Vacuum suction cups can act as a lens, leading
to a higher risk of fires.
Placing objects within the vehicle
On the instrument panel
Precautions for driving
Do not place any item on the instrument panel as
Driving over the speed limit is prohibited.
the items placed on the instrument panel may
The vehicle shall not exceed the speed indicated
by speed limit signs or mark lines.

64
Overloading the vehicle is prohibited Flat tyre
Overloaded driving is dangerous. Do not carry It is forbidden to continue to drive the vehicle
passengers or goods more than what is on the under the flat tyre condition. Driving with one or
indicated maximum limit. Do not carry more flat tyres is extremely dangerous since it
passengers in the luggage area or the trunk. heightens the probability of accidents. In
addition, tyres, wheels, suspension and vehicle
Fatigue driving is prohibited body will be damaged. At this moment, please
Fatigue driving is extremely dangerous as the replace the tyre immediately.
judgement, view and attention of driver in When any of the following situations occur, check
fatigue state will drop substantially. It is likely if vehicle tyres are punctured or have gone flat.
to bring about severe accident.  When the steering wheel vibrates.
 When the vehicle vibrates abnormally.
Shutting down the vehicle is prohibited  When the vehicle is leaning at an abnormal
The brake assist device and power steering angle.
system will not work if the vehicle is shut down If a tyre is flat or broken during driving, hold the
while driving, which may lead to deterioration of steering wheel firmly and gently step on the
braking efficiency, and cause severe accident. brake pedal to slow down.
Emergency braking or sudden steering may
Turning the steering wheel fully in either lead the vehicle to go out of control.

direction and holding it there for an

The vehicle’s undercarriage, tyres, and
extended period of time is prohibited
wheels suffer a strong impact
Failure to do so may make the power steering
When the vehicle’s undercarriage, tyres, and
system have less efficiency, or even damage
wheels suffer a strong impact, stop the vehicle
the system.
immediately in a safe spot and inspect the
Braking vehicle. Check that there is no leaking of brake
While driving, do not continuously step on the fluid or fuel, and that suspension parts, tyres,
brake pedal or apply the parking brake. Failure wheels, drive shaft components, etc., are not
to adhere to the advice may lead to premature deformed or damaged. If you discover signs of
wear-and-tear in the brake pad or overheating leakage or damage, do not continue to drive the
in the brakes, thereby affecting braking efficiency vehicle. Failure to adhere to the advice may
and possibly leading to accidents as a result. lead to accidents.

The brake emits a warning sound

When going downhill
The disc brake will emit a warning sound when Vehicle shutdown or neutral coasting is
the brake pad wears and needs to be replaced. prohibited
If you hear a seismic noise while braking, do not The braking force assist device and power
continue driving. Otherwise it will severely steering system will not work if the vehicle is
wear the brake disk, damage the brake parts shut down while driving downslope. In this
and affect the braking efficiency or even lead scenario, braking efficiency
to an accident. will be compromised and you feel the steering
wheel heavy, making the occurrence of accidents
more likely.

65
Driving on uneven road surfaces electrical elements, resulting in a major accident.
When stopping on a curb or on a road surface
with a height difference, make sure that the tyre While driving on a flooded road, the brake pads
is not crushed and deformed by the curb or will become wet and braking efficiency will be
other obstacles. reduced, which can easily lead to accidents.
When the vehicle must pass a curb, a deceleration Please step gently and repeatedly on the brake
zone or a similar obstacle, you should try to slow pedal in order to warm up the brake until full
down along the vertical angle of the obstacle. brake performance has been recovered.
Failure to do so may result in damage to the tyre,
especially to the side wall of the tyre. Precautions for passengers
Driving in the following road conditions may Moving within the vehicle is forbidden
cause damage to the bumper. Please slow down It is forbidden for the passenger to leave his or
and drive carefully. her seat, or to move around inside the vehicle.
 Where there are varying levels, such as at Otherwise, during emergency braking, the
parking lot entry/exit points. passenger's body or head, etc., may suffer
 Where there are steep slopes, like in the injurious impact.
case of multi-story parking lots.
 Uneven road and road section with track. Do not extend your hands or head outside
 Sections of road where there are potholes.
the vehicle window or sunroof
 When moving from a flat surface onto a
If you stretch your hands or head out of the
slope, or when moving from a slope
vehicle, it is prone to hitting against the window
 onto a flat surface.
frame when braking the vehicle in emergency
 When parking on road with deceleration
or closing the window. In this case, it may cause
strip or along curb.
serious injury or even death.

Driving on slippery road surfaces, such as

Do not carry child passengers on your lap
wet, snow-covered, or icy roads When riding as a passenger, do not carry infant
Emergency braking, sudden acceleration, or or child passengers on your lap even if you are
sudden steering on slippery road surfaces may already wearing a seat belt. Further, do not
cause vehicle tyres to skid and the vehicle to go surround or enclose the infant or child using
out of control, thereby causing an accident. any part of the seat belt; this may cause
When accelerating and decelerating, the engine grievous injury or even death during collisions
speed may make a significant change, it is or emergency braking.
prone to occurring side slip and thus causing an
accident. Child passengers must not be allowed to
In cold weather, you should slow down when operate equipment such as vehicle doors,
driving in areas of ice, such as bridges and
vehicle windows and the sunroof
shady areas.
If child passengers are allowed to operate
doors, windows and sunroof, they are at risk of
Driving on flooded roads clipping their hands, heads, necks, etc., in the
Be careful while driving on a flooded road.
Driving on a flooded road may lead to short
circuit of electrical components or damage to

66
operation. All these can cause grievous hurt. Regular maintenance
If the vehicle door is opened during the driving, Regular maintenance ensures a longer service
it is prone to shooting the children out of the life and the best economy of your vehicle.
vehicle and consequently, causing serious
injuries and even death. Turn off temporarily unnecessary
Please use a child safety lock and a window electrical components
lock switch to prevent children from accidents Turn off temporarily unnecessary functions
because of an incorrect operation. such as the air-conditioning, seat heating and
rear window heating to reduce power use.
Parking the vehicle
Do not park near flammable materials Close windows and sunroof
Do not drive or stop on a road with a lot Opening the windows or the sunroof increases
offlammable materials such as grass or scrap paper. drag, so turn them off when you do not need
Wood or plywood placed too close behind the them.
vehicle may cause a fire.
Inertial glide
Do not run the vehicle for a long time in The accelerator pedal should be released when
poorly ventilated places approaching the red light or on a larger slope,
Do not run the vehicle for a long time in a allowing the vehicle to take advantage of
poorly ventilated area such as a garage. This inertial glide.
may cause exhaust gas to accumulate, which
may lead to carbon monoxide poisoning, causing
serious personal injury and even death.

Economic driving
Predictable driving
Maintain a proper distance with the front running
vehicle and avoid unnecessary acceleration and
braking. The stable vehicle speed can increase
the driving range.

Avoid unnecessary weight

The loaded and overloaded driving of the vehicle
will increase energy consumption.
Before driving, remove unnecessary items from
the vehicle.

Check tyre pressure periodically

Too small tyre pressure will increase the rolling
resistance, thereby increasing the energy
consumption while increasing tyre wear.

67
Advice on driving in harsh environments

Vehicle equipment Driving in the rain

Please note that this manual contains all the Please drive carefully on slippery road
standard equipment, country-specific equipment surfaces
and special equipment for this model series. As poor vision, foggy windscreen and slippery
Thus, some equipment or features described in roads are likely to occur when running on rainy
this manual may not be installed onto your days, please drive carefully.
vehicle or are only available in some markets. When performing emergency braking, steering
For further configuration information, please and accelerating on a slippery road, tyres may
refer to relevant sales information or consult slip, making it difficult to control the vehicle,
with your distributor selling the vehicle to you. which may lead to an accident.
While driving in rain, water film can form between
Driving in foggy weather the tyre and the ground. At this time the tyre can
Turn on the fog lamps easily lose its grip, so for safe driving you should
While driving in fog, you should turn on the fog slow down.
lamps.
Sound horn to warn pedestrians and ⚠WARNING
vehicles Try to avoid driving in a heavy rain or a rainstorm.
If you hear the horn of other vehicles, respond Try to avoid driving in a heavy rain or a rainstorm
immediately by honking your horn to indicate
your position.
Wading drive
Precautions for wading drive
Drive at low speed and look out for safety
 Before wading drive, you shall confirm the
When driving in foggy weather, try to travel at
water depth of the road area. If there is more
a low speed and keep a safe distance from the
water or the water depth is unknown, you
vehicle ahead.
shall drive to take a detour and not go
through a direct course.
Do not wipe fog on the glass during
 By analyzing road conditions, do not allow
vehicle running the vehicle to enter an unknown region. Such
Due to large temperature difference inside and regions may contain hidden obstacles, such
outside the cab, mist may condensates on the as ditches or manholes.
inside surface of the windscreen that can  While fording in the water, keep low speed
affect driver's sight. (speed should not exceed 10 km/h) and do
In this case, you can use the A/C defrosting not park or shift gears.
function or open the vehicle windows a little to  When the vehicle passes an intersection, try
have the same air temperature inside and to avoid the waves generated by the
outside the vehicle. preceding vehicle to prevent water from
This will prevent condensation to form on the entering the front grille.
inside surface of windscreen. If you wish to wipe  During fording in the water, if the vehicle can
away the condensation on the windscreen glass, not move due to power failure (flameout)
please do so only after bringing the vehicle to a caused by a malfunction, do not try to start
stop. Never try to do so while driving the vehicle. the vehicle again at this point. Immediately
consult authorized service centre for treatment.

68
Check and maintenance after Wading If you experience a flat tyre in the course of the
Once the vehicle has been safely driven through drive, hold the steering wheel securely, step
water, perform the following operations gently on the brake pedal to decelerate, and
immediately: avoid actions such as emergency braking or
 Step on the brake pedal a few times sudden steering. Failure to adhere to the advice
consecutively, and check whether brake may cause the vehicle to go out of control.
performance has been compromised.
 Check the horn. Preventing sunstroke
 Check all vehicle lights. Strong sunlight and high temperature in hot
 head to the authorised service centre as season easily lead to sunstroke.
soon as possible for routine inspection. Keep the driving room well ventilated and
During wading drive, water may enter the prohibit fatigue driving.
components and parts of transmission
system and dilute lubricant, which may ⚠ WARNING
lead to system malfunctions.
Never leave a child in the vehicle unattended.
 Leaving children alone in the vehicle during
⚠CAUTION hot seasons can easily cause heat stroke,
 Travel in water is only applicable in emergency dehydration, personal injury or even death.
situations and it cannot be used as a part of  If the child, left alone in the vehicle, plays with
routine driving. matches, lighters other items, it is easy to
 Driving through water can damage the cause vehicle fire accidents.
engine and electrical components.

⚠ CAUTION
Driving during the hot seasons When parking the vehicle, do not leave items such
Hot weather and high temperature in summer as lighters, spray can, soft drink cans, spectacles,
are bad for the normal vehicle running and the etc., inside the vehicle.
health of driver. To ensure driving safety, the  As temperatures inside the vehicle can get
driver shall pay attention to the following very high, a leakage of gas from the lighter,
items: spray cans or cracks in these containers can
lead to fire.
To prevent the engine from overheating  Should a soft drink can burst inside the vehicle,
The engine is prone to overheating in the hot its contents may splash onto electrical
season due to higher ambient temperature. components and cause short circuit.
Therefore, please step up the inspection and  As temperatures inside the vehicle can get
maintenance of the engine cooling system, very high, it is easy to make resin lens or
and remove debris embedded in the radiator glasses deformation, resulting in crack.
chips.
Driving in cold season
Preventing flat tyre Snow tyre
As air pressure in the vehicle tyre rises with In the cold season when the temperature is low,
temperature increase, flat tyre is likely to occur due to the special characteristics of the standard
in case of hot weather and high temperature in tyre (tyre width, rubber composition and pattern
hot season. type, etc.), the tyre elasticity

69
 decreases, further weakening the traction and  The four wheels must have snow tyres
braking force. At the same time, the tyre noise installed at the same time.
will be increased, even leading to serious  Always use snow tyres having the same size
standard tyre cracks, abnormal wear and tear as the standard tyre.
and other permanent damage.  The same model, size (rolling circumference)
It is recommended to use snow tyres when and pattern type of snow tyres must be used.
the temperature is lower than 7°C in cold  Snow tyres can only be used during the cold
season. Snow tyres can greatly improve the season.
handling stability of the vehicle, but also  Be sure to comply with the allowable
improve the vehicle's braking response and maximum limits for snow tyres (such as
shorten the braking distance. maximum speed, maximum load, etc.).
Otherwise, tyres may be damaged, causing
traffic accidents.
NOTICE
 Do not reverse the rotation direction of the tyre.
Although all-season tyres with M + S markings
are better for the cold season, they fail to achieve
the performance of snow tyres. Therefore, it is Tyre chains
still necessary to use snow tyres when driving The use of tyre chains depends on the current
on snowy or icy roads. standards in specific countries or regions, and
the installation of tyre chains must comply with
local regulations. Install tyre chains on the drive
⚠ WARNING
wheels only.
Although snow tyres can improve the
Do not install tyre chains on only one tyre. Install
vehicle driving performance in winter, do not
tyre chains following the instructions provided
drive at risk situation, and still keep cautious!
by the tyre chain manufacturer and tighten them
 Be sure to adjust your speed and driving
as tightly as possible.
style based on visibility, weather
conditions, road and traffic conditions.
 Do not exceed the speed and load rating ⚠ CAUTION
indicated on the installed snow tyres when Observe the following precautions when
driving. installing tyre chains:
 Improper size or installation of tyre chains will
⚠ CAUTION damage the vehicle brake pipeline,
When the pattern of snow tyres is severely suspension, body and tyres, etc. Choose
worn, their applicability to cold season will be suitable tyre chains and ensure that they are
largely lost. If snow tyres have aged, their properly installed.
applicability to cold season will largely be lost  Install and remove tyre chains in a safe
even though the tyre pattern wear is location. Turn on the emergency flashers, and
insignificant. set the warning triangle behind the vehicle.
Consult the dealer for specific replacement  Always set the power supply to OFF mode and
standards of snow tyres. apply the parking brake before installing the
tyre chains.
Snow tyre instructions:  Do not install tyre chains on emergency wheels.
 You must comply with the relevant laws
and regulations of the host country.

70
  Do not install tyre chains when the tyre ⚠WARNING
pressure is low. When parking on snowy roads, shut down the
 Do not damage aluminium alloy vehicle powertrain.
wheel rim when using tyre chains.  If the engine is running at the start of the
vehicle with snow accumulated around it,
⚠WARNING exhaust gas may seep inside the vehicle
Observe the following precautions when interior, causing severe injury or even death
driving with tyre chains: by carbon monoxide poisoning.
 After installing tyre chains, the driving  When you feel that exhaust gas comes into
speed shall not exceed 40 km/h or the max. the vehicle, you can take the following measures:
speed recommended by the tyre chain  Drive the vehicle to a ventilated area and
manufacturer, whichever is lower open all the windows. Set the air conditioning
 After installing tyre chains, always check to the external circulation mode, adjust the
that the tyre chains are properly installed air flow to the maximum, and introduce fresh
after travelling 0.5 to 1.0 kilometer to ensure air from the outside into the vehicle.
safety. Retighten or reinstall the tyre chains
if they are loose.
 After installing tyre chains, vehicle control
may be adversely affected. Operation such
as sudden acceleration, sharp turns and
emergency braking should be avoided as
much as possible, otherwise accidents may
occur.
 When driving, if you hear the tyre chain
knocking on the vehicle body or chassis,
stop the vehicle and re-tighten the tyre
chain. If you can still hear the sound, slow
down until the sound disappears.
 Avoid driving on bumpy road surfaces or
over potholes.
 Slow down before entering the curve, so
that you can control the vehicle.
 Remove the tyre chains when driving on
road surfaces without snow, or they may
affect driving performance and severely
damage tyre.

71
Advice on driving during run-in period

Vehicle equipment
Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Tyre
Take extra care in the first 500 km when
driving with a set of new tyres.
New tyres do not offer optimal grip until they
have been broken-in.

Friction lining of brake pad

New friction lining of brake hardly achieves
optimal braking effect within first 400 km
vehicle running.
New friction lining of brake must also be run-
in to achieve the best friction performance. If
you feel that the braking force of the vehicle is
insufficient, you can step on the brake pedal to
increase the braking force.
During the run-in period, avoid applying extra
load on the brake. For example, emergency
braking, especially emergency braking at high
speed and while running
on slope.

⚠ CAUTION
 The friction linings and brake disk may
wear to different degrees depending on
the using condition and the driving
method.
 Due to the vehicle speed, braking force
and environmental conditions (such as
temperature and humidity), there may be
noise when braking, which is normal.

72
Hybrid vehicles

About hybrid vehicle

CF490C012FA6
(A) Gasoline engine (D) High-voltage wiring harness
(B) A/C compressor (E) Drive motor assembly
(C) Power battery pack (F) Generator assembly

NOTICE
Depending on vehicle configuration, your vehicle may differ from the appearance shown in the figure.
Please refer to the actual vehicle.

This vehicle is a hybrid vehicle, which is different from general fuel vehicles in characteristics.
Please be familiar with the characteristics of the hybrid vehicle and drive it carefully.

⚠WARNING
 Do not touch, remove or replace parts with high-voltage warning signs, orange cable and their
connectors on the vehicle to prevent high-voltage electric shock .
 After the vehicle is started, the power system will be hot. Be careful of high voltage and high
temperature, and always follow the instructions on the vehicle safety warning label.

73
The driving method of hybrid vehicles is exactly the same as that of general fuel vehicles. The hybrid
power system can automatically start the operation mode of the engine and drive motor according to
the running state and driving mode of the vehicle, thus improving fuel efficiency and reducing exhaust
emission.
 The drive motor usually drives the vehicle at a low speed.
 The engine generally drives the vehicle at high speed or during more active driving.

Energy recovery
The function is mainly used to convert a part of kinetic energy of the vehicle during braking or
coasting into electric energy of the power battery, thereby extending the distance to empty.
The energy recovery intensity can be set via [ Vehicle Settings ][ In-Car ][ Driving Control ]
[Energy Recovery Level] on the multimedia display screen.

2B39B89D1E4F

NOTICE
When the single pedal driving mode is started, the energy recovery intensity is not adjustable.

⚠ WARNING
The reduction of vehicle speed caused by energy recovery cannot be a substitute for normal
braking. The brake pedal should be depressed during deceleration and parking.

NOTICE
When the vehicle decelerates obviously as the energy recovery function is activated, the brake lamp
may be turned on.

NOTICE
The energy recovery will not be carried out when the vehicle is under the following conditions:
 The vehicle is in N gear position.
 The power battery is fully charged.
 The temperature of the power battery is too high or too low.

74
Power battery vent Position 1 : near the fuse box of the engine
There is an air intake vent under the rear seat compartment
for cooling the power battery.
If the air inlet is blocked after the vehicle is
started, the power battery will overheat.
To protect the power battery, the system may
limit the discharge/charging of the power battery.

NOTICE
 Clean the vent regularly to prevent the
power battery from overheating.
 Do not place foreign matters near the vent;
26D3328BB5DA
otherwise, the power battery may overheat
and be damaged. Position 2 : under the luggage area
 Prevent foreign matters or water from
entering the vent; otherwise, a short circuit
may occur and the power battery may be
damaged.
Battery safety switch
The battery safety switch is used to disconnect or
connect the power supply of the high voltage
system.

⚠WARNING
271AE9E2658B
Do not attempt to operate the battery safety
Remove the fuse box cover and you can see it.
switch. It can be used only when repairing the
vehicle and performing operations related to
high voltage system.

75
Power supply mode

Vehicle equipment ⚠ WARNING

Please note that this manual contains all the Do not switch the power supply to OFF mode
standard equipment, country-specific equipment while driving.
and special equipment for this model series.
Thus, some equipment or features described in ⚠ CAUTION
this manual may not be installed onto your  Do not place the smart key on the instrument
vehicle or are only available in some markets. panel, on the ground, on the instrument
For further configuration information, please cluster, in the storage box or in the luggage
refer to relevant sales information or consult area. Otherwise, the power supply mode
with your distributor selling the vehicle to you. cannot be switched.
 When the engine is not running, do not keep
Power supply mode switching the power supply in the ON mode for a
When carrying the smart key, directly press extended period of time to prevent loss of
the power supply switch to change the power battery power.
supply mode.  When you leave the vehicle, switch the
power supply to OFF mode and carry the key
with you.

60A8F42B7CAE
No. Mode Effect
Electrical components are
1 OFF
in the nonworking state.
All electrical components
2 ON
can be used.

NOTICE
When the smart key is carried in the vehicle,
depress the brake pedal with the shift lever in
the P position. The vehicle can be started by
pressing the power supply switch regardless of
the power supply mode.

76
Starting and shutting down vehicle

Vehicle equipment
Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.
6F9BB49E4883
Starting the vehicle When the smart key is lost, put the mechanical
Normal starting key above the marked position on the
1. Carry your smart key with you. bottom of the cup holder and perform the
2. Adjust the seat position and take correct vehicle-on operations to start the vehicle. If the
driving gesture. vehicle cannot be started, contact authorised
3. Ensure that the parking brake is applied. service centre immediately.
4. Make sure the P gear is engaged.
5. Depress the brake pedal.
6. Press the power supply switch to start the
vehicle. (At this time, the indicator light
READY in the instrument cluster being on
indicates that the drive system is ready.)

NOTICE
After the vehicle is started, the engine will start
or stop automatically according to the vehicle
state.
D7578B674662
Try not to store the vehicle in a very cold
environment, as this may cause the vehicle to ⚠ WARNING
fail to start.  Be sure to sit on the driver seat before
starting the vehicle. Failure to do so may
Emergency start lead to accident, serious injury or even death.
If the prompt “Is the key in the vehicle” is shown  Never step on the accelerator pedal under
(such as the under-voltage smart key, serious any circumstances when starting the vehicle.
damage to the door guard or the rear bumper  Always start the vehicle even if you need to
and other situations), place the key above the move the vehicle slightly. Otherwise, an
sign in the bottom of the cup holder and accident may be caused.
perform the vehicle-on operations to start the
vehicle. If the vehicle cannot be started, contact
authorized service centre immediately.

77
Shutting down the vehicle
1. Stop the vehicle steadily and switch the shift
lever to the gear P.
2. Press the power supply switch to shut down
the vehicle.
Emergency shutdown
In case of emergencies such as inability to stop
the vehicle by normal means during driving (at
the speed of greater than 5 km/h), you can shut
down the vehicle in emergency by performing
any of the following operations:
 Press and hold the power supply switch.
 Press the power supply switch 3 times
continuously within 2 seconds.

⚠ WARNING
 Shutting down the vehicle while driving may
cause a collision or major personal injury.
 Do not forcibly shut down the vehicle while
driving in non-emergency situations.
When the vehicle is forcibly shut down, the
brake and steering wheel power will be lost.
As a result, it is more laborious to step on the
brake pedal and the steering wheel is heavier.
Therefore, decelerate as much as possible
before shutting down the vehicle.

⚠ WARNING
Do not touch high-temperature components
such as the engine, exhaust pipe, and radiator
immediately after shutting down the engine.
Otherwise, you may be burned.

NOTICE
After the engine has operated at a high speed or
with high load for a long time, it is recommended to
allow the engine to idle for a short time or drive at
a low speed for some distance.

78
Parking braking

Vehicle equipment  If the parking brake is not required, press and

Please note that this manual contains all the hold the EPB switch while switching the
standard equipment, country-specific equipment power supply to OFF mode.
and special equipment for this model series.  After the vehicle is stationary, pull up the
Thus, some equipment or features described in EPB switch to apply the parking brake. At
this manual may not be installed onto your this point, the parking brake indicator light
vehicle or are only available in some markets. on the instrument cluster turns on.
For further configuration information, please
refer to relevant sales information or consult Emergency braking
with your distributor selling the vehicle to you. In case of emergency, pull up the EPB switch and
hold it, and then use the EPB system to brake
Tips for safety the vehicle.
⚠ WARNING Emergency braking can be cancelled as long as
 Parking on a slope steeper than the the EPB switch is released or the accelerator
prescribed limit may cause an accident. pedal is stepped on.
Please drive safely and avoid risk
parking situations. ⚠ WARNING
 If the slope is too steep, use of the parking The emergency braking function can only be
brake system will not be able to stop your used in the event of an emergency (e.g. the
vehicle completely. In this case, step on the brake pedal is blocked).
brake pedal to prevent the vehicle from
rolling. Releasing the parking brake

Electronic parking brake (EPB)

Applying the parking brake

7AAE367204E4
When the power supply is in ON mode, step on
the brake pedal and press the EPB switch to
B189679B6768 release the parking brake.
 When the vehicle is stationary and the At this time, the parking brake indicator light
power supply is switched to OFF mode, the on the instrument cluster turns off.
electronic parking brake (EPB) will be
applied automatically. At this point, the NOTICE
parking brake indicator light on the If the vehicle is powered off abnormally, the
instrument cluster turns on.
parking brake fault warning light on the
instrument cluster turns on after the vehicle

79
is powered on again. In this case, the system needs 3. Step on the accelerator pedal and the
to self-learn. Pull up the EPB switch first, then parking brake is automatically released. If
depress the brake pedal and press the EPB switch the accelerator pedal is not depressed for
to release the EPB normally. a long time, the AVH function will be
deactivated, and the vehicle will
AVH function automatically switch to electric parking
mode, thus applying the braking force.
The following conditions will deactivate the
AVH function forcedly:
 The driver seat belt is released.
 The driver door is opened.
 Switch the power supply mode to OFF
mode.
 It works for more than 3 minutes.

⚠ CAUTION
B918B72586DE In the case of automatic car washing and
Auto Vehicle Hold (AVH) enable the driver not to towing, the parking brake needs to be
step on the brake pedal for extended periods nor released. You can set wash/trailer mode via
apply the electronic parking brake frequently [Vehicle Settings][ n-Car][ Driving Control]
when the vehicle is on a slope, meets red lights or on the multimedia display screen.
stops and goes. It allows the driver to drive more ( Page 87)
comfortably and reduces the risk of vehicle rolling.
After the driver door is closed, the driver seat belt Automatic departure function
is fastened, and the vehicle is started, press the With the parking brake applied to the vehicle,
AVH switch to turn on or off the automatic parking the parking brake is automatically released
function. when the driver fastens the seat belt,
depresses the accelerator pedal and the
Instructions system detects the driver's intention to
1. Turn on the AVH function. At this time, the depart.
automatic parking function is in the ready On a slope, more traction is required to avoid
state, and the indicator light on the rolling.
instrument cluster turns yellow.
2. Depress the brake pedal to stop the vehicle.
The vehicle will automatically apply the
parking braking. At this point, the AVH function
is working, and the indicator light on the
instrument cluster is green.

80
Automatic transmission

Vehicle equipment  Vehicles are prohibited from coasting with

Please note that this manual contains all the the N gear engaged; otherwise, there is a risk
standard equipment, country-specific equipment of accidents.
and special equipment for this model series.
Thus, some equipment or features described Automatic mode (D)
in this manual may not be installed onto your The D gear is used for normal driving.
vehicle or are only available in some markets. When the D gear is engaged, the transmission
For further configuration information, please can automatically adjust till the appropriate
refer to relevant sales information or consult position is reached based on the vehicle speed
with your distributor selling the vehicle to you. and the required acceleration, to achieve the
best economy.
Introduction to gear positions How to shift
Park gear (P) After the vehicle is started, normal gear shifting
The P gear is used to assist in parking the vehicle. operations can be performed. Before the start of
When the P gear is engaged, the transmission is the vehicle you should always step on the brake
mechanically locked to prevent the vehicle from pedal; otherwise the vehicle will move if the
sliding. driving gear of the shift lever has been engaged.

NOTICE ⚠ WARNING
In case of abnormal power failure of the In order to avoid the damage to the vehicle or
vehicle, the gear "P" will require self learning accidents, the vehicle must be completely
after the vehicle is powered on again. At this stopped before the gear is engaged.
time, the system will perform self-learning
automatically after the brake pedal is NOTICE
stepped on or the EPB is pulled up.  When the vehicle speed is lower than 2 km/h,
and the driver's door is opened and the
Revers (R) gear driver’s seat belt is released, the vehicle will
The R gear is used for reversing. be shifted to gear P automatically.
 After the vehicle is turned off, it will
Neutral (N) automatically switch to P gear.
The N gear is an unpowered gear, and the
transmission system is in a state of not NOTICE
transmitting power when this gear is engaged. When the shift is completed, make sure that the
It is used when the vehicle is to be started or correct gear is engaged.
stopped.

⚠ WARNING
 When stopping the vehicle temporarily in
gear N, be sure to apply parking brake or
depress the brake pedal. Otherwise, the
vehicle may coast and cause an accident.

81
 At this point, you can only shift to a specific
gear or simply cannot shift gears. Please
stop at the safe place as soon as possible
and contact authorised service centre.

Crawling function
After the vehicle is started, you shall switch
to the driving position, and release the
parking brake and the brake pedal. At this
time, you don't need to step on the
220B68470DD2
accelerator pedal, and the vehicle can crawl
(A) Parking gear button
(B) Shift knob slowly.

Shift to P gear Start the vehicle

When the vehicle is stationary, press the parking How to move off normally
gear button. 1. Fasten the seat belt and confirm that the
parking brake has been applied.
Shift to gear D, R or N 2. Start the vehicle.
 When switching from P gear to N, R or D gear in 3. Depress the brake pedal and engage gear
case the vehicle is stationary, depress the brake D.
pedal and turn the knob. 4. Release the brake pedal and then gently
 When switching from N gear to D gear in case the step on the accelerator pedal to allow the
vehicle is stationary, depress the brake pedal vehicle to accelerate.
and clockwise turn the knob.
 When switching from N gear to R gear in case the NOTICE
vehicle is stationary, depress the brake pedal When the vehicle starts, the automatic DDA
and counterclockwise turn the knob. function will automatically release the
 When switching from D gear to N gear, just parking brake.
counterclockwise turn the knob directly.
When switching from R gear to N gear, just Launch Control
clockwise turn the knob directly. 1. Fasten the seat belt and confirm that the
parking brake has been applied.
NOTICE 2. Start the vehicle and confirm that the ESC
The engaged gear will be shown on the shift panel function is turned off.
and the multi-information display of the 3. Left foot depress the brake pedal, put the
combination instrument. gear in position "D", and release the
parking brake.
⚠ WARNING 4. When the accelerator pedal is depressed
If a transmission-related error message appears on on your right foot, the instrument will
the combination instrument the transmission may prompt “launch control activated”.
enter the emergency operation mode. 5. After the brake pedal is released, the
vehicle starts to launch until the vehicle
is started.

82
⚠ WARNING ⚠ CAUTION
 Be sure to drive carefully within the limits  When it is necessary to stop the vehicle
permitted by law. temporarily at the slope, the brake pedal
 Launch control can only be used in places must be stepped on or the parking brake
without cross traffic or pedestrians The must be applied. Do not use accelerate pedal
driver has the responsibility to ensure that or crawling function to keep the vehicle
the driving mode and acceleration do not stable, otherwise the transmission will be
endanger or hinder the safety of other damaged.
traffic participants.  Do not use the P gear to park on the slope,
 The function cannot be used when the otherwise it will damage the transmission.
vehicle runs on slippery roads. Otherwise,  When stopping the vehicle on a slope, block
the vehicle will get out of control and cause the wheels with something if necessary to
an accident. prevent rolling.

⚠ CAUTION
If the braking time is too long (about 8 seconds)
and the vehicle does not start after the launch
control mode is activated, the launch control
function will be disabled and the timeout
protection will be enabled to protect the motor
system. When the vehicle is in timeout state, it is
necessary to release accelerator pedal before
disabling the timeout state for the next launch
control.

NOTICE
When the power battery has a low power or
temperature, the launch control function may
not be available.

Stop the vehicle

1. After releasing the accelerator pedal, depress
the brake pedal.
2. After the engine speed is stable, switch to
the P gear.
3. Apply the parking brake or shut down the
vehicle engine directly as required.

NOTICE
After the vehicle engine is shut down, the
vehicle will automatically apply the parking
brake.
4. Release the brake pedal.

83
 Driving mode

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Switching method
The vehicle driving mode can be set in the NOR, ECO, SPORT or SNOW mode via the
[Vehicle Settings][ In-Car][ Driving Control] on the multimedia display.

316296C03F18

Standard mode
The vehicle will choose the best driving mode according to the current driving condition and the
dynamic property and economy of the vehicle.
Economic mode
It delivers optimal fuel economy, with fuel consumption reduction and comfort as the primary goal,
and is suitable for medium- and low-speed road conditions.
Sport mode
Increase the vehicle power, resulting in a higher level of responsiveness and driving experience.
Suitable for use on wide, flat roads with few vehicles.

NOTICE
When the main lamp switch is in the AUTO position, the sport mode lighting setting can be activated
or deactivated via the [Light Settings] on the multimedia display screen.

Snow mode
It is suitable for driving on snow, wet and low-adhesion roads, ensuring more stable and safe
driving of vehicles under severe driving conditions.

84
Single pedal function

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Single pedal mode

Turn on or turn off single pedal mode via multimedia by [Vehicle Settings] [ In-Car]  [Driving
control]

ECB595505773
How to use
When the single pedal driving function is turned on and the gear is in position "D", the accelerator pedal
can be depressed, raised or completely released for accelerating, sliding, decelerating, and stopping
completely. Meeting the normal driving requirements, it is operated flexibly and easily and can be used
to improve the range significantly.
The following conditions may cause the single pedal driving function to be turned off or malfunction.
 The driving is in snow mode.
 The driving mode is switched to snow mode.
 The accelerator pedal, brake pedal or the whole vehicle is faulty.
 When the operation intervene the vehicle torque, such as AVH, cruise assist, Intelligent cruise,
Intelligent drive and so on.

⚠ WARNING
 The speed reduction caused by single pedal driving function cannot replace normal braking
completely. In case of emergency, please step on the brake pedal in time.
 It is not recommended to use the single pedal driving function under snow, ice or slippery road
conditions.

85
 ⚠ CAUTION
When the gradient is too high or the vehicle is in trouble, please step on the brake pedal in time to
prevent the vehicle from slipping.
The single pedal driving function allows the vehicle to slow down and stop by invoking energy
recovery. A vehicle can stop on most paved roads, but the deceleration effect will be affected by
slope gradient and vehicle load. Therefore, drivers shall always be prepared for braking.

NOTICE
The electronic parking brake (EPB) will be automatically applied after 3 minutes when the vehicle is
decelerated and stopped by using the single pedal driving function.

86
Vehicle wash/trailer mode

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Vehicle wash/trailer mode

Turn on or turn off wash/trailer mode via [Vehicle Settings][ In-Car][Driving] on the multimedia
display screen. After the mode is turned on, the vehicle will automatically shift into gear N and release
the parking brake.

AD1BE1AD8494
This mode is used for washing the vehicle or towing the vehicle to a flat trailer, but it is not suitable
for towing the vehicle for a long time.
Opening method
 Engage the gear P.
 Depress and hold the brake pedal.
 Start the vehicle wash/trailer mode through multimedia.

NOTICE
The vehicle wash/trailer mode will turn off automatically when the following conditions occur.
 Switch the power supply to OFF mode.
 Enable the parking brake function.
 The vehicle speed is higher than 8 km/h.
 The battery power is drained or the voltage is too low.

87
 Fording mode

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Wading mode
Before wading, turn on or turn off wash/trailer mode via multimedia by [Vehicle Settings] [In-Car] 
[Driving control] After the mode is started, the system will force the engine to start without shutdown.

1DB38D3C093B
After wading, this mode can be turned off through multimedia.

NOTICE
Wading is only applicable in emergency situations and cannot be used as a part of routine driving.
( Page 68)

88
Steering wheel assist mode

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Switching method
When the power supply is in ON mode, it can be switched to power steering mode via
[Vehicle Settings] [ In-Car] [ Driving Control] on the multimedia display screen.

Type I

FE07865B853F
Type II

0A593A17E77C

NOTICE
When switching between power steering modes, the following conditions need to be met:
 The electric power steering system is functioning correctly.
 The vehicle speed is less than 125 km/h.
 No apparent turn operation has been carried out.

89
Light
It increases the power steering for easy steering. It is applicable to traffic congestion driving environment
such as urban areas.

Comfort
It is suitable for general driving habits.

Sport
It reduces the power steering and increases the steering wheel feedback. It is recommended to use it
under high speed, rain and snow and other cases.

⚠ CAUTION
After the battery of the vehicle is disconnected, to power on and start the vehicle again, you should
initialize the angle of the electric power steering (EPS) system. Otherwise, certain EPS functions will
be abnormal. Operation approach: Turn the steering wheel counterclockwise to the limit and hold for
about 1 s, then turn it clockwise to the limit and hold for about 1 s, and finally turn the steering wheel
to make the wheels return to center.

90
Parking assist system

Vehicle equipment NOTICE

Please note that this manual contains all the The radar detection device of parking assist
standard equipment, country-specific equipment system is affected by ultrasonic characteristics.
and special equipment for this model series. Incapability or poor detection may be caused
Thus, some equipment or features described in under the following circumstances, which are not
this manual may not be installed onto your system failures:
vehicle or are only available in some markets. For  The obstacle is a wire net, fence, post, rope,
further configuration information, please refer to or other such thin objects.
relevant sales information or consult with your  The obstacle is an object whose surface
distributor selling the vehicle to you. does not reflect the detection signal or a
person wearing such clothing.
Safety tips  The obstacle is snow, cotton or other
substances of which the surface can easily
⚠ WARNING
absorb sound waves.
 The parking assist system is only an auxiliary
 The obstacle is below the radar sensor.
tool, which cannot replace the driver's
 The obstacle is an acute-angle reflector or
judgement on external conditions. In any case,
cone shaped object, such as a right-angle
the driver should be responsible for the safety
square column and a fire hydrant box.
of the vehicle and observe the surrounding
 Driving through grass or over rough terrain.
conditions of the vehicle at any time during
 Reversing on a ramp.
parking or similar operations.
 There are ultrasonic noises with the same
 There are blind spots to the coverage of the
frequency around, such as metal noise,
parking assist system, and obstacles in certain
high-pressure gas emission noise, or a car
areas may not be detected. Therefore, during
horn directed at the sensor.
parking or similar operations, please make
 The license plate is bent or tilted, or a large
sure that there are no children or animals near
license plate decorative frame is installed.
the vehicle.
 A foreign object is stuck to the surface of
the sensor, such as invisible vehicle cover.
⚠ CAUTION In order to ensure the normal operation of
 When reversing, make sure that the tailgate the system, the sensor must be kept clean
has been fully closed. and free of snow and ice.
 Do not tap the camera and sensor.
 Do not flush the camera and sensor with a high-
pressure water gun in the front. Otherwise,
water may result in system failure or fire.
 Do not use wearing or sharp material to clean
the camera and sensor.
Please wipe with a soft cloth or wash with water
(low water pressure) to clean the surface of
camera and sensor.

91
Reverse radar Instructions
System introduction
The reverse radar is a radar-detection device.
When reversing, the sensor installed will work to
detect any obstacle that is present behind the
vehicle, as well as the distance between the
vehicle and that obstacle. The system will
provide the driver with audio prompts to help
the driver park as easily and safely as possible,
and to avoid collisions.
How to use 3EEA03D8B88D
 Switch to gear R and the reverse radar will  When the power supply is set to the ON
automatically turn on. mode or the engine is started, touch the
 When the R gear is exited, the reverse radar
button to manually turn on or off the anti-
will automatically turn off.
collision radar.
 Switch to the R gear position and the anti-
Detection scope and alarm mode
collision radar will automatically turn on.
Detection scope
Sensor position Switch to the P gear position and the anti-
[m]
collision radar will automatically turn off. If
Rear on both sides 0.6
the driving speed exceeds 15 km/h, the
Rear center 1.5
anti-collision radar will automatically turn

If the sensor detects an obstacle within the off.

detection scope after the reverse radar is turned Detection scope and alarm mode
on, the alarm will start. When the distance between Detection scope
Radar sensor position
the vehicle and the obstacle reduces, the [m]
frequency of alarm sounds will gradually increase. Front on both sides 0.6
When the distance between the obstacle and the Front centre 1.0
vehicle is within about 0.3m, the alarm sound will
Rear on both sides 0.6
be heard for a long time, and the vehicle shall not
be reversed to avoid collision. Rear centre 1.5

Anti-collision radar After the anti-collision radar is activated, if the

System description sensor detects obstacles within the detection
An anti-collision radar is a radar detection range, it will start to give an alarm.
device. During parking, sensors are used to As the distance between the vehicle and the
detect whether there are obstacles in front of obstacle decreases, the frequency of alarm
and behind the vehicle, detect the distance of sounds will gradually increase.
obstacles, and give sound prompt to assist the When the distance between the obstacle and
driver to park safely and easily. the vehicle is within about 0.3 m, the alarm
sound will be heard for a long time. In this case,
the vehicle should not be reversed continuously
to avoid a collision.

92
Reverse camera  When the power supply is set to the ON
About the system mode or the engine is started, touch the
The reverse camera captures images from behind button to turn on or off the AVM.
the vehicle using the rear view camera and  When the R gear position is engaged, the
transmits the image signal to the screen for AVM will turn on automatically.
display, thereby assisting the driver to safely and  When the P gear position is engaged, the
easily park the vehicle. AVM will turn off automatically.

How to use Camera interface

 Switch to gear R and reverse camera will
automatically turn on. After the reverse camera
system is turned on, you can select various view
modes according to personal preference.
 The reverse camera will be deactivated
0D3F5E5576C0
automatically when R gear is exited.
(A) Function setting area
(B) Top view area
Static guide line (C) Image area
The static guide line indicates the straight guide (D) View sign
path when you reverse the vehicle. If an obstacle
enters the red line area of the guide line, it shall
Function setting
immediately stop reversing, otherwise a collision
: view switching button
accident will occur.
Touch the button to switch to the wide view;
and touch the button again to exit the wide
Around View Monitor (AVM) view.
System description : guide line
AVM uses four cameras to capture images Touch the button to set the guide line to be
surrounding the vehicle and sends a video signal revealed or hidden. After setting the display
to the display screen for display. This helps the mode, the guide line displays the body width,
driver safely and easily drive to avoid accidents. which can assist the driver in parking.
Instructions : radar obstacle
Touch the button to set the radar obstacle to
show or hide. After the setting is shown and
when an obstacle is detected, a radar
identification will be shown in the obstacle
direction.
MOD : lateral moving object detection
You can activate or deactivate the lateral
moving object detection function. After the
function is activated, when moving pedestrians,
bicycles, or vehicles are detected, the image
3EEA03D8B88D interface will display an alarm message.

93
 : vehicle washing station mode (A) Free view
Touch the button to enable or disable the washing After selecting the free view, drag the image
station mode. After the washing station mode is area to adjust the view at will. When the
enabled, the tyre's forward track will be displayed, vehicle speed exceeds 10 km/h, or the [ AUTO ]
and the line width indicates the tyre width. button on the top view is manually touched
: system setting and selected, the system will switch to the
Touch the setting button to enter the system automatic view mode.
setting interface, on which the [Intelligent viewing
angle switch] function can be activated or ⚠ CAUTION
deactivated. If the doors (including the tailgate) are opened
The button is highlighted, indicating that the or the side mirrors are folded, the image on the
function is activated. When the function is turned on: corresponding side will not be shown properly.
When the vehicle is in the D gear position, if the
front radar detects an obstacle less than or equal Auto parking assist system
to 1 m from the vehicle body, it will automatically
System introduction
switch to the front top image.
The auto parking assist system identifies the
When the vehicle is in the R gear position, if the
proper parking space and automatically
rear radar detects an obstacle less than or equal
control the vehicle by sensors, and the driver
to 1 m from the vehicle body, it will automatically
can enter and exit a parking space by simply
switch to the rear top image.
following the system prompts to maneuver
It will automatically switch to the previous image
the vehicle.
after the obstacle is removed.
How to use

View switching
View switching
When the D gear is engaged, the image interface
automatically switches to the front view image;
when the R gear is engaged, the image interface
automatically switches to the rear view image.

Manual view switching

Touch the top view area, then the top view
displays the multi-directional control buttons. 57AB5BDC0591
Touch to select the button indicating each After starting the vehicle, the vehicle speed is
direction, then the image area will display the less than 30 km/h, tap the button and the auto
view image corresponding to this button. parking assist system is activated. Automatic
parking is completed by following the prompts
displayed on the multimedia display screen
when the system is activated.

EA0A15CDE022

94
⚠ CAUTION  Recoverable interruption beyond time limit,
 The fully automatic parking assist system can number of interruptions beyond limit,
only be used in standard, economic or sports number of parking movements beyond
driving modes. In other driving modes, the limit, and total parking time. beyond time
fully automatic parking assist system is not limit.
available.  Press the button.
 In order to ensure the parking safety, the  When exiting from the parking space, if it
driver needs to monitor the surrounding judges that there is no travel direction or the
environment of the vehicle at any time, to road is clear, there is no need to use
brake and take over the vehicle in time when automatic parking function.
there is a collision risk.  The slope of the ground where the vehicle is
located is too large.
NOTICE
 The default parking mode can be set via the
Cases in which automatic parking assist may
multimedia display screen.
not work properly:
 The parking-out function can only be used
 There is irregular road edge near to the
when the vehicle is stationary.
parking place or the road edge is covered
 When looking for the parking space, please
by leaves and snow.
make sure that the vehicle is 0.5 ~ 1.5 m away
 Parking space is located in corners or
from the parking space nearby, otherwise, the
curves.
full-automatic parking assist system may
 Heavy wear of the vehicle tyres or installation
not identify the parking space.
of unapproved tyres (including non-full-
size spare tyres).
Precautions
 When parking over grass or rough terrain.
During automatic parking process, the following
 When the parking slot is forward/ reverse
operations may cause temporary interruption of
inclined position.
automatic parking. Automatic parking can be
 There are ultrasonic noises with the same
resumed when the interruption disappears.
frequency around, such as metal noise,
 Vehicle doors (including the back door) open.
high-pressure gas emission noise, and horn
 Driver’s seat belt unlocked.
sensor buzzing.
 Obstacles appear on the parking path.
 The sensor is smudged or covered.
 Throttle intervention.
 Heavy fog, rain or snow.
Cases in which automatic parking assist is
During automatic parking process, the following
forbidden:
operations may cause automatic parking to exit.
 Tyre chains or spare tyres are installed.
 The vehicle speed exceeds 40 km/h in the
 The loaded objects exceed the vehicle size.
process of searching for parking space.
 A tow hook is installed.
 Gear, steering wheel or parking brake
 The slope of the ground where the vehicle
intervention.
is located is too large.

95
 Parking settings
The functions related to park setting system can be set via multimedia display screen, please refer
to the actual vehicle for detail information.

43C3A515080C
[Road calibration setting]
During the using of vehicle, when the camera position changes due to bumping of vehicles or aging
of parts, the image mosaic may be misplaced, blurred and distorted.
At this time, the image mosaic effect can be optimized through the road calibration setting.
Please refer to the prompt information on the multimedia display screen for the specific
calibration methods and requirements.

⚠ WARNING
Road calibration should be carried out in a well-lit and wide place. The road calibration process
should strictly comply with road traffic.

[Setting of radar automatic starting]

You can turn on or turn off radar automatic activation function. After the function is enabled, if the
moving speed is less than 10 km/h and there is an obstacle detected within the detection range, the
front radar and image system will be started automatically. The system will be automatically turned
off if with a few seconds the distance of the obstacle does not change, the obstacle is far away, or
the vehicle is applying the parking brake.

[Flank protection]
After the function is enabled and when the sensors on the left and right sides of the vehicle identify
obstacles, the system prompts the driver to park carefully through pictures and sound alarms.

96
[Low speed emergency braking]
You can turn on or turn off emergency braking function at low speed. After the function is activated,
when the vehicle is running at a low speed, the low speed emergency braking indicator on the
image interface will be illuminated in green, which indicates that the function is normally activated. If
an obstacle is detected during low speed driving and a collision risk is determined, the system will
automatically apply emergency braking to reduce the risk of a collision. At this moment, the indicator
turns red.

⚠ CAUTION
 The function is only an auxiliary one, which cannot guarantee that all obstacles are detected under
all conditions.
 Under complex road conditions (such as off-road conditions or narrow passages), please turn off
the low-speed emergency braking function. Otherwise, the system may apply unnecessary braking.
 Please turn off the low-speed emergency braking function after the vehicle is equipped with
traction devices or when the vehicle is towing other vehicles. Otherwise, the system may apply
unnecessary braking.

[Default parking mode]

You can set the default parking mode of the auto parking assist system.

[Using vehicle at any time]

[Intelligent pre-cooling function]
You can activate or deactivate the intelligent view switch function. After starting the function, you
can carry out pre-cooling function through mobile phone application, so that the vehicle can get
proper temperature before using and improve user experience.

97
Tyre pressure monitoring system

Vehicle equipment  TPMS cannot replace regular tyre maintenance.

Please note that this manual contains all the Check the tyre frequently to ensure proper tyre
standard equipment, country-specific equipment pressure, even if no alarm is received from
and special equipment for this model series. TPMS.
Thus, some equipment or features described in  Tyre pressure can be affected by factors such as
this manual may not be installed onto your the heat generated from vehicle operations, the
vehicle or are only available in some markets. For external environment, journey time, etc. Under
further configuration information, please refer to normal conditions, the tyre pressure fluctuates
relevant sales information or consult with your around 30 kPa, which is normal.
distributor selling the vehicle to you.
Monitoring function
System introduction Press the Back button on the steering
The tyre pressure monitoring system (TPMS) wheel to switch the multi-information display to
monitors tyre pressure and temperature in real the driving data interface , and then press the
time and alerts the driver to take appropriate Up button  or Down button  to switch the
action to avoid an accident when an abnormality driving data interface to the tyre pressure
occurs in the tyre. monitoring interface so that you can view the
pressure and temperature information of four in-
NOTICE use tyres in real time.
The communication device conforms to the When the tyre pressure is too low or the
standard and requirements of NBTC temperature is too high, the abnormal tyre icon
on the tyre pressure monitoring interface shows
⚠ CAUTION red and flashes.
 If the tyre replaced is not a standard spare tyre,
it may affect the normal operation of TPMS. Alarm function
 TPMS may not work properly when the tyre When the tyre pressure is too low or the
chain is installed or the wheel is covered. temperature is too high, the combination
 TPMS may not work properly due to radio instrument will send out the following alarm as
interference. follows:
 After replacement of tyres or tyre rotation,  The multi-information display will display the
start the vehicle and drive at a speed higher corresponding alarm interface. The abnormal
than 30 km/h for about 9 minutes, then the tyre icon is displayed as red and sends out
TPMS will automatically identify the tyre audible alarm.
pressure, tyre temperature and location. If  Tyre pressure monitoring system warning lamp
the tyrepressure and the tyre temperature
on the combination instrument illuminates.
are not displayed or displayed incorrectly
If the tyre alarm message appears in the trip, you
after 9 minutes, please contact authorized
should avoid performing sudden, acute turns and
service centre to reset TPMS as soon as
emergency braking. Reduce the speed, drive to a
possible.
safe area and stop the vehicle as soon as possible.
Then contact authorised service centre for
trouble handling.

98
Fatigue driving reminder system

Vehicle equipment Fatigue warning

Please note that this manual contains all the When the system monitors the following conditions,
standard equipment, country-specific equipment the instrument cluster displays a “Reminder:
and special equipment for this model series. Take a Break” alarm screen, accompanied by an
Thus, some equipment or features described in audible alarm.
this manual may not be installed onto your  The system detects that the driver is in a
vehicle or are only available in some markets. fatigue driving condition and the vehicle
For further configuration information, please speed exceeds 65 km/h.
refer to relevant sales information or consult  The vehicle has been driven (the engine has
with your distributor selling the vehicle to you. been running) for 4 consecutive hours.

Introduction of fatigue driving ⚠ WARNING

reminder  While the vehicle speed remains less than 65
The fatigue driving reminder system identifies km/h, the system will not activate the
the driver's fatigue level by continuously warning even if the driver shows signs of
detecting the driver's operation of the vehicle. fatigue.
If the system recognizes that driver is fatigue,  In some situations, the driver's abilities may
sound and visual alarms will be given to alert be unaffected even though he/she is
the driver to drive with care. fatigued. In such circumstances, the system
will not issue a warning to the driver.
For this reason, when the driver shows signs
⚠ WARNING
of fatigue, it is very important to stop the
 Fatigue driving is strictly prohibited.
vehicle and rest in a timely manner, regardless
Reasonable parking intervals should always
of whether the driver condition monitoring
be arranged for long-distance driving to
system has issued a warning.
ensure adequate rest.
 This feature cannot be used to loosen driving
 It is always the driver's responsibility to ensure
restrictions. Regular stops must be arranged
that he/she is in a good driving condition.
during the long driving for adequate rest.
 Fatigue driving warning function is only an
auxiliary tool and may not be able to actually
monitor driver fatigue. In some cases, the Functional limitations
system may judge normal driving behavior When the fatigue driving reminder function is
as fatigue. turned on, the following situations may cause
the fatigue driving reminder function to be
Instructions limited or not work at all:
The fatigue driving reminder function can be  Cruise control function activated
activated or deactivated via  The front wiper is on.
[Vehicle Settings] [ In-Car] → [Body] on the  The wiper control combination switch is
multimedia display screen. currently being operated.
The [Fatigue driving reminder] function is  The driver side door is open. Depress the
activated by default. brake pedal.
 The hazard warning lamp is on.
 The driver's seat belt is not used.
 The turn signal lamp is on.

99
Cruise control system

Vehicle equipment  The driver must not leave his or her seat
Please note that this manual contains all the when the cruise control system is activated.
standard equipment, country-specific equipment  To keep fuel economy, do not drive at a low
and special equipment for this model series. speed under a higher gear, or drive at a high
Thus, some equipment or features described in speed under a lower gear.
this manual may not be installed onto your  If the cruise control system is in operation
vehicle or are only available in some markets. and you want to slow down quickly, press
For further configuration information, please brake pedal as usual.
refer to relevant sales information or consult
with your distributor selling the vehicle to you. Instructions
NOTICE
Cruise control system introduction Since the cruise control system is designed for
While driving at high speed on straight, smooth driving on highway and other roads with good
highways, the cruise control system allows the conditions, the cruising speed should be within
user to keep the vehicle at a certain speed the range of 30 to 150 km/h.
without stepping on the accelerator pedal for
extended periods of time.

⚠ WARNING
 The cruise control system is an auxiliary
tool and cannot take the place of the driver
in judging the road and traffic conditions
nor the driver ’ s driving.
In any case, the driver shall be responsible
for the safety of the vehicle and must
concentrate on driving carefully at all times. 62275BE701A9

 In order to avoid operating the cruise (A) ON/OFF button

control system by mistake, if you do not use (B) Restore speed setting/acceleration button
it, turn the cruise control system off. (C) Speed setting/deceleration button
 Incorrect use of the cruise control system (D) Speed release setting button
can lead to the collision accidents. Turning on the system
 You should only use the cruise control
1. Press the button to light up the CCS
system when there is good weather and the
indicator light on the instrument cluster,
vehicle is traveling on straight highway.
 Using cruise control system in urban areas, indicating that the cruise control system has
on meandering roads, on wet and slippery been turned on.
roads, or in other adverse weather conditions is 2. Adjust to the required speed, then press the
not recommended. button. The current speed is set and the
 Do not use the cruise control system when vehicle is running at this speed. The cruising
traveling on slopes. The system cannot speed setting information will be displayed
maintain a set speed while the vehicle is on the multi-information display of the
traveling uphill or downhill. instrument cluster.

100
Increasing the cruising speed Cancelling the set speed
There are three methods to increase the set There are two ways to cancel the set speed:
speed:  Depress the brake pedal.
 Press the button to increase the speed.  Press the set speed release button on
 Press and hold button to increase the the steering wheel .
speed continuously. When the set speed is cancelled, the system
 Step on the accelerator pedal to accelerate does not turn off and the CCS indicator on the
to the desired speed, and press button to instrument cluster remains on.
set a new speed.
Reducing the cruising speed Restore the set speed
There are three ways to reduce the cruising When you have cancelled the set speed, the
speed: system does not turn off. When the speed
 Press the button to reduce the speed. meets the system requirements, pressing the
 Press the button to reduce the button will automatically return to the
 speed continuously. speed set before it was cancelled. The cruise
 Step on the brake pedal to reduce the setting information will be shown again in the
vehicle to the required speed, then press the information centre.
button to set a new speed.
Turning off the system
Accelerating temporarily Press the button to close the cruise control
To accelerate temporarily during vehicle speed system and cancel the previously set speed
setting, depress the accelerator pedal. After and the indicator light on the instrument
acceleration, release the accelerator pedal to cluster will go out.
resume the previously set speed.

101
Cruise control assist system

 The cruise control assist system is not

Vehicle equipment
recommended for use in conditions such as
Please note that this manual contains all the
urban areas, winding roads, narrow roads,
standard equipment, country-specific equipment
wet and slippery roads, heavy rain or other
and special equipment for this model series.
harsh weather conditions.
Thus, some equipment or features described in
 When you drive on a slope, the cruise
this manual may not be installed onto your
control assist system is not recommended
vehicle or are only available in some markets.
for use, based on the following point :
For further configuration information, please
The cruise control assist system cannot
refer to relevant sales information or consult
maintain the set speed when you drive up
with your distributor selling the vehicle to you.
and down the slope.
After a preceding vehicle has passed the
System description
top or bottom of a slope, the cruise control
While you drive on straight, smooth highways,
assist system may not detect the preceding
the cruise control assist system allows you to
vehicle, causing sudden acceleration or late
keep the vehicle at a certain speed without
braking.
stepping on the accelerator pedal. When the
 The cruise control assist system may exit
system detects that the vehicle in front of you
when camera is illuminated by strong light or
is driving at a speed less than the cruising speed
the illumination intensity changes suddenly.
set by your vehicle, the vehicle will be running
The camera may be affected when the front
by following the preceding vehicle at a set safe
windscreen around the camera is polluted,
distance.
frozen, damaged or covered.
The vehicle equipped with the intelligent cruise
control assist mode can also keep driving in the
middle of the lanes during cruising. Instructions
NOTICE
WARNING Since the cruise control system is designed for
 The cruise control system is an auxiliary tool driving on highway and other roads with good
and cannot take the place of the driver in conditions, the cruising speed should be within
judging the road and traffic conditions nor the range of 30 to 150 km/h.
the driver’s driving. In any case, the driver
shall be responsible for the safety of the
vehicle and must concentrate on driving
carefully at all times.
 When cruise control assist system is not in
use, turn it off to avoid incorrect operation.
 Incorrect use of cruise control assist system
may result in a crash.
 The cruise control assist system can only
be used when you drive on a clear road in
147410C8D101
good weather conditions.
(A) ON/OFF button
(B) Restore speed setting/acceleration button
(C)

102
(D) Speed setting/deceleration button select the adaptive cruise control assist mode
(E) Distance level adjustment button or TJA mode or to turn off (OFF).
(F) Speed release setting button  The indicator light (white) on the
instrument cluster turns on to indicate that
Instrument cluster display the adaptive cruise control assist mode is on.
NOTICE  The indicator light (white) ( on the
Due to different vehicle configurations or instrument cluster turns on to indicate that
different instrument themes, the graphics the TJA mode is on.
displayed on the instrument cluster are for
reference only. Refer to the actual vehicle. Setting the cruising speed
Press the button to set the vehicle speed.
After the vehicle speed is successfully set, the
adaptive cruise control system indicator or
intelligent cruise control assist indicator on
the instrument cluster turns from white to green.
The minimum set speed of the cruise control
assist system is 30 km/h.

NOTICE
371C8F72E10A When the adaptive cruise control assist mode is
(A) Setting the speed activated, the following basic conditions must
(B) Distance level be met before the cruising speed can be set:
The distance level is not a fixed distance,  All doors are completely closed.
but a following distance between your  The driver wears the seat belt properly.
vehicle and the preceding vehicle. The  The engine is started and the D gear position
following distance between your vehicle is engaged.
and the preceding vehicle will vary with  The ESC is activated.
 No parking brake is applied.
the speed of your vehicle under the same
 The vehicle speed is less than 150 km/h.
distance level.
 The vehicle driving mode is in the standard,
(C) Following distance display When the
ECO or sport mode.
system detects the presence of a vehicle
ahead, it will determine the degree of
When the intelligent cruise control assist mode
danger of the current following distance
is activated, the following basic conditions must
based on the speed of the vehicle, and be met before the cruising speed can be set:
display it in different colours.  All doors are completely closed.
(D) Lane marking  The driver wears the seat belt properly.
Turning on the system  The engine is started and the D gear position
After the engine is started, press the ON/OFF is engaged.
button on the steering wheel repeatedly to  The ESC is activated.

103
 No parking brake is applied. ⚠ WARNING
 The vehicle speed is less than 150 km/h. Setting a low distance level may result in a delay
 The system detects a lane marking. in reaction in the event of unexpected situations,
 If the vehicle speed is less than 60 km/h, it and it is always your responsibility to adjust the
is required to detect the moving targets. distance level appropriately.
 The vehicle driving mode is in the
standard, ECO or sport mode.
NOTICE
Increasing the cruising speed  The distance level is not a fixed distance, and
There are three methods to increase the set the actual distance between your vehicle and
speed: the preceding vehicle will vary with the
 Press button to increase the speed. speed of your vehicle.
 Press and hold the button to increase  Select a higher distance level when driving
the speed continuously. on wet and slippery roads than when driving
 Step on the accelerator pedal to accelerate to on dry roads.
the desired speed, and press button to Cancelling the set speed
set a new speed. There are two ways to cancel the set speed:
 Depress the brake pedal.
NOTICE  Press the set speed release button on
The vehicle will accelerate to the set speed the steering wheel .
only when the road ahead is clear. Otherwise, After the set speed is cancelled, the system is
it will follow the vehicle in front according to not turned off, and the adaptive cruise control
the set distance. system indicator light or intelligent cruise control
assist indicator light on the instrument
Reducing the cruising speed cluster turns from green to white.
There are three ways to reduce the cruising
speed: NOTICE
 Press the button to increase the speed. The set speed will be automatically cancelled
 Press the button to reduce the speed under any of the following circumstances:
continuously.  Depress the accelerator pedal to make the
 Step on the brake pedal to reduce the vehicle accelerate for more than 15 minutes.
vehicle to the required speed, then press  The N, R or P gear position is engaged.
the button to set a new speed.  The driver seat belt is released.
 The driver door is opened.
Accelerating temporarily  The parking brake is applied.
To accelerate temporarily during vehicle speed  The anti-lock brake system (ABS) is activated.
setting, depress the accelerator pedal. After  The HDC is activated.
acceleration, release the accelerator pedal to  The ESP is activated/deactivated.
resume the previously set speed.  The vehicle rolls backwards.
 The brake disk is overheated.
Adjusting distance level  The engine is shut down.
Press the distance level adjustment button on  The vehicle driving mode is in the nonstandard,
the steering wheel to adjust the following ECO or sport mode.
distance to the front vehicle.

104
Restore the set speed Curve road auxiliary function
When you have cancelled the set speed, the When cruise assist system is enabled, if the
system does not turn off. When the speed vehicle is entering a curve road at too high
meets the system requirements, pressing the speed, the curve road auxiliary function will
button will automatically return to the reduce the vehicle speed appropriately.
speed set before it was cancelled. The cruise
setting information will be shown again in the ⚠ WARNING
information centre.
 When entering and exiting a curve road or
driving in a curve road, the system may not
Turning off the system
detect the vehicle in front of the same lane
Press the ON or OFF button repeatedly to in a timely manner, in which case the
select OFF. The system is turned off and the vehicle may be braked too late, and the
previously set speed and gap is cancelled. driver must be careful and ready to control
the vehicle.
Queuing auxiliary function  When driving around a curve road, the
This function enables the vehicle to follow system may incorrectly detect vehicles in
another vehicle within the speed range of other lanes, causing unnecessary braking.
0~150 km/h.  When driving on a sharp turn road (for
In the event of traffic congestion, the vehicle example, a serpentine road), if the vehicle
can be slowed down to a stop following the in front exits the sensor detection scope,
preceding vehicle. At this point: the vehicle may suddenly accelerate, and
 If the preceding vehicle leaves within 3 s, the driver must be cautious and ready to
the vehicle will automatically follow the manipulate the vehicle.
preceding vehicle. Lane center keeping function during
 If the preceding vehicle stops for a long time
cruising
(3 s to 3 min), either push the control rod
This feature is only available in TJA mode,
upwards or lightly step on the accelerator
which assists the driver in keeping the vehicle
pedal can restart the system.
in the middle of the lane boundary when the
 If the preceding vehicle is parked for more
system is operating and the sensor detects a
than 3 minutes, the vehicle will automatically
lane boundary or a moving vehicle ahead.
apply the parking brake.
 If the driver opens the door or releases the
seat belt, the vehicle will automatically
NOTICE
apply the parking brake.  This feature is not available in adaptive
cruise control mode.
 This function is cancelled at the same time
NOTICE
when the set cruise speed is cancelled.
After the cruise function is cancelled, the queuing
auxiliary function is automatically disabled.

105
  A vehicle is running at a low speed in front
⚠ CAUTION
of you when you are driving at a speed of
In some cases, the lane center keeping
over 60 km/h.
function may not work properly or not work
 An oncoming vehicle is running in the
during cruising. For example,
same lane.
 Cruise at a speed higher than 60 km/h
 A vehicle or object that crosses a lane.
(including 60 km/h), there are no lane
 Pedestrians or animals and small vehicles
lines,
(such as bicycles and motorcycles) are
 lane lines at both sides are blurred, and
seen.
the non-standard lane boundaries or
 The vehicle in front decelerates suddenly.
lane boundaries are covered.
 Water, snow or mud splashed by surrounding
 Cruise at a speed below 60 km/h, there
vehicles hinders the sensor detection.
are no lane lines or the lane lines on both
 The vehicle head tilts up due to overload in
sides are blurred, the non-standard lane
the luggage area.
boundaries or the lane boundaries are
 The vehicle is running on a winding or
covered, and there is no vehicle running
narrow road.
ahead.
 The preceding vehicle has a relatively
 There is an object on the road that
small tail dimension or very large ground
affects the identification of the lane
clearance.
boundaries (such as water, gaps, ruts,
text signs, bumps or pits).
Sensor
 Low visibility (such as rain, snow, fog and
The cruise assist system identifies lane
night etc.). The vehicle is strongly
boundaries and detects targets through the
affected by the side wind.
camera above the front windscreen.
 The lanes merge or separate.
 The camera is illuminated by strong light
or the illumination intensity changes NOTICE
suddenly. When the combination instrument indicates
 The front windshield around the camera that the system sensor detection is restricted,
is polluted, frozen, damaged or covered. please check and ensure the camera and its
Vehicles are running on a sharp turn or a surroundings are clean and free of obstructions
narrow road. so that the system can operate properly.
 If the vehicle is driving too close to the
preceding vehicle, the camera detection
scope is hindered.

Functional limitations of the cruise

assist
Under the following conditions, the cruise
assist system may not take the braking
measures:
 A vehicle suddenly appears in front of you.

106
Intelligent driving assist system

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Intelligent driving
After starting the vehicle, via the [Vehicle Setting]  [Driving] on the multimedia to set the
corresponding functions.
WARNING
⚠ WARNING
The intelligent drive assist system is only an auxiliary tool. It can not use as a substitute for the
driver’s judgment of road and traffic conditions, nor it can replace the driver’s driving. In any case,
the driver shall be responsible for the safety of the vehicle and must concentrate on driving carefully
at all times.
The driver must always keep his hands on the steering wheel and ready to turn at any time.

Sensor
Intelligent drive assist system identifies lane boundaries and detects targets through the following
components.
 Camera.
The camera is located on the upper part of the front windshield.
 Sensor
Sensors are located on both sides of the rear bumper.

NOTICE
When the instrument indicates that the system sensor detection is limited, check that the camera,
sensor, and surrounding area are clean and clear of obstructions to ensure proper system operation.

NOTICE
1. This communication device conforms to standards or technical requirements of NBTC.
2. The electromagnetic field intensity of this communication device conforms to Safety Standard for
People to Use Communication Device Healthily published by National Telecommunications
Commission.

107
Forward assist system
The forward assist system identifies vehicles on the lane via a camera on the front windscreen. When
the risk of collision ahead is detected, the system will issue an alarm or conduct brake intervention
to mitigate the consequences of the accident.

695A11F62AE3

⚠ WARNING
We cannot guarantee that this system will function as expected in all situations. Therefore, it is
prohibited to drive the vehicle toward a pedestrian, animal or other vehicles for the purpose of
testing the system, which could cause serious injury or death.
In complex driving conditions, the system may apply unnecessary braking. This may happen, for
example, in construction sites, at railway tracks, and when water is sprayed or splashed in front of
the vehicle.
The system may not work properly when there is low visibility (e.g. rain, snow, fog and haze, night, etc.).
The the system may exit when the camera is illuminated by strong light or the illumination intensity
changes suddenly.
The camera may be affected when the front windscreen around the camera is polluted, frozen,
damaged or covered.

Pedestrian/collision safety assist

Pedestrian safety assist : it can detect passengers and cyclists.
Collision safety assist : it can detect most vehicles stationary or driving in the same direction as
your vehicle (such as passenger cars, trucks, buses, etc.).
 Without braking: the function is turned off.
 Brake: the function is turned on.
When the vehicle speed exceeds 30 km/h and the system detects that there is collision risk for
pedestrians or vehicles, it will give an alarm to prompt the driver to drive safely. There are 2 alarm
levels: audible alarm (pre-alarm), short brake alarm (emergency alarm).
In case of emergency, if the driver does not apply the brake, the system will control the vehicle to
automatically perform emergency braking (limited braking), and the left and right turn signal lamps
will flash quickly to remind the rear vehicle, so as to reduce the collision risk.

108
 NOTICE
 At low vehicle speeds, this function may slow the vehicle to a standstill, but will not keep the
vehicle stationary. At this point, the driver should apply the brake actively.
 If the driver steps on the accelerator pedal or turn the steering wheel during the emergency
braking, the system will disengage the emergency braking.

NOTICE
 If the vehicle speed exceeds 65 km/h and the system determines that the distance between your
vehicle and the vehicle ahead is too close, the instrument cluster will show the prompt message
of "Please keep a safe distance".
 When cruise control assist system is working, the safe distance alert function is blocked.
 Poor lighting will affect the detection range. Turn on the headlamps when driving at night.

Detecting the target

NOTICE
For valid targets identified by the system, the system may not always achieve the same level of
performance, depending on vehicles, pedestrians, scenes, road conditions.
 The cyclist must be an adult and the bicycle must be designed for an adult. The system can only
work best when it detects clear information about the body and the contour of the bicycle, which
means that the system needs to clearly identify contour information such as the bike, head, arm,
shoulder, thigh, and the normal cycling of the person.
 The system detects pedestrians in contrast to the background (e.g., the color of the pedestrian
clothing is contrasting with the color of the surrounding environment). If the contrast is low, the
pedestrian will be detected later or not at all, meaning that warnings and braking will be delayed
or unavailable.
The system can only work best when it detects clear information about the shape of the body,
which means that the system needs to clearly identify information about the head, arm,
shoulder, thigh, etc. of the person and the normal walking pattern of the person.

Intersection assistance
When the vehicle speed is lower than 20 km/h, and the vehicle turns around at a intersection, if an
oncoming vehicle or a pedestrian is detected and there is a risk of collision, the system will apply
brake.
The system can detect pedestrians and vehicles driving in the opposite direction of your vehicle
(such as passenger cars, trucks, buses and so on). Poor lighting will affect the detection range. Turn
on the headlamps when driving at night.
Front collision warning sensitivity
Sensitivity is divided into three levels.
 Standard: it indicates that the distance is normal when an alarm is sounded as defined by the system.
 Low: it indicates that the distance is shorter when an alarm is sounded.
 High: it indicates that the distance is longer when an alarm is sounded.

109
 Lane keeping assist system
The lane keeping assist system is designed for a vehicle travelling on motorways, and other roads in
good condition. By using a camera on the windscreen to detect lane markings, it reminds the driver
to make a correction when the driver accidentally deviates from the lane. Some of the system
functions even assist the driver in correcting the direction to reduce the risk of a collision.

18D239526562

⚠ CAUTION
The lane keeping assist system properly works only when the lane marking is clearly visible. It may
not work properly or even not work in some cases. For example:
 Lane markings are unclear, non-standard, or otherwise obscured.
 There are objects on the road that affect the identification of lane markings (e.g. water, cracks,
ruts, signs, crosswalks, bumps and pits, etc.).
 There is low visibility (e.g. rain, snow, fog and haze, night, etc.).
 The vehicle is strongly affected by the crosswind.
 The lanes merge or separate.
 A strong light shines on the camera, or the light intensity abruptly changes.
 The front windscreen around the camera is polluted, frozen, damaged or covered.
 The vehicle is running on a sharp turn, a narrow road, or a road prone to rollover.
 The vehicle is running too close to the preceding vehicle, and the camera detection scope is
hindered.

NOTICE
If you turn on the turn signal lamp, turn the steering wheel, operate the accelerator pedal or the
brake pedal before passing through a lane marking, the system will not send an alarm. In this case,
the system considers you are taking the initiate to drive the vehicle.

NOTICE
When the driver controls the steering wheel with a small force, the system may not detect the
driver's hand holding the steering wheel, and the instrument cluster will send an alarm.

110
Lane keeping assistance
When the lane keeping assistance function is turned on, the keeping assistance form can be selected.
 Lane departure warning: it can warn the driver to drive safely when the driver deviates from the
lane unconsciously.
 Lane keep assist: it can assist the driver to correct the steering wheel to keep the vehicle in the
lane when the driver deviates from the lane unconsciously. If the correction fails, the system will
give an alarm to alert the driver to drive safely.
 Lane center assist: it can assist the driver to correct the steering wheel to control the vehicle to
drive in the centre of the current lane. If the correction fails or the vehicle is off the current lane,
the system will give an alarm to alert the driver to drive safely.

NOTICE
The lane keeping assistance function can only work when the vehicle speed is within 60 to 150 km/h.

When the lane keeping assistance function is turned on, the lane markings will be displayed on the
instrument cluster.
 Grey: it indicates that the system fails to detect a lane marking.
 Green: it indicates that the system detects a lane marking or it is correcting the steering wheel.
 Red and flashing: it indicates that the system sounds an alarm, and the driver needs to correct
the direction in time to make the vehicle return to the lane.

NOTICE
The lane center assist functions only when the system identifies the lane markings on the left and
right sides.
Emergency lane keeping (ELK)
When the emergency lane keeping is turned on, the system will more actively correct the steering
wheel in case of an emergency to reduce the risk of collision. For example:
when the driver is unaware of lane deviation or turns on the turn signal lamp to change lanes, there
is a risk of collision with the oncoming vehicle in the adjacent lane or a vehicle from the rear in the
same direction, or there is a curb or a pit outside the lane.

NOTICE
The emergency lane keeping functions only when the vehicle speed is within 60 to 150 km/h.

⚠ WARNING
In some cases, the emergency lane keeping function may not work properly or not work. For example :
 For smaller targets (motorcycles, bicycles, etc.)
 For stationary targets
 The current vehicle is moving too close to the preceding vehicle and prevents the camera from
detecting it.
 The rear vehicle is driving too close to the current vehicle and prevents the sensor from detecting it.

111
 Wisdom dodge function
After the wisdom doge function is turned on, if the lane center assist or intelligent cruise control is
turned on and in working condition, when the system identifies that the vehicle is about to overtake
the adjacent large vehicles (wagon, truck, bus, etc.), it will control the vehicle to move slightly away
from the large vehicle. After overtaking the large vehicle, your vehicle will return to the central area
of the current lane.

NOTICE
The wisdom dodge function will not begin to work until the vehicle speed reaches 60 to 140 km/h.

⚠ CAUTION
The following situations may not trigger the wisdom dodge function:
 The system detects that there is a large vehicle on the adjacent lane on one side, and there are
vehicles on the adjacent lane on the other side or the adjacent lane on the other side is a curb.
 The vehicle is driving in severe weather such as night, heavy fog, rain and snow.
 The vehicle is in a curve.

Early warning mode

There are three warning modes: sound, vibration, and sound + vibration.
Early warning sensitivity
Sensitivity is divided into three levels: low, standard and high.

Rear side assist system

The rear side assist system can detect vehicles behind your vehicle or in the adjacent lane through
sensors on both sides of the rear bumper. If there is a risk of collision, the system will issue an
alarm to remind the driver to drive safely.

ED5AF2C2219D

112
 NOTICE
 Keep both sides of the rear bumper clean, and do not paste any objects and cover any ice, snow,
mud and other foreign objects, so as not to affect the normal work of the sensor.
 Improper repair or modification of the vehicle may cause the sensors to be dislocated, which may
affect the proper operation of the rear side assist system. Therefore, it is recommended that you
maintain and repair your vehicle at the authorized service centre.
 Turn off the rear side assist system when towing other vehicles.

⚠ WARNING
In some cases, it may not work properly or even not work. For example:
 For stationary targets (vehicles, pedestrians, etc.)
 Driving in bad conditions such as rain, snow, etc.
 Driving on a sharp bend, a sloping road, a wide or narrow lane

Warning light

C8364549158A
The warning lights are located on the surfaces of the left and right side mirrors.

⚠ WARNING
Do not paste any objects on the warning lights to avoid affecting the system's alarm function.

Doubling assistance
During driving (with the speed exceeding 15 km/h), when the system detects that there is a vehicle
in the blind area of the side mirrors or a quick approaching vehicle behind the adjacent lane, the
warning light on the corresponding side should be on. If you turn on the turn signal lamp at the same
side at this time, the warning light turns to flash and an audible alarm is accompanied, which
indicates that there is danger if continuing to change the lane.

Door open warning

When the system detects that there are approaching vehicles and bicycles and other targets in the
adjacent lanes on both sides after the vehicle stops and that there is a risk of collision when the door
is opened, the warning light at corresponding side will go on. If the passenger continues to open the
door on the corresponding side at this point, the warning light will flash and an audible alarm will
sound to indicate that it is dangerous to continue opening the door.

113
 NOTICE
The door open warning system will only function in the following conditions:
 When the vehicle power supply in ON mode.
 Within 3 minutes of switching the power supply mode from ON to OFF mode.
Rear collision warning
When the system detects that there is a fast approaching vehicle behind the subject vehicle and
there is a risk of collision, the left and right turn signal lamps will flash quickly, accompanied by an
audible alarm and instrument prompts to remind the driver of the subject vehicle that a dangerous
target is approaching, and warning thedriver of rear vehicle to drive safely.

Reverse side warning

When the reverse side warning function is enabled, if during reversing the system detects that there
is a risk of collision with a moving vehicle in the blind area of the side mirror, it will give an alarm to
remind the driver to drive safely.
When the reverse side brake function is enabled, limited braking can be applied when there is a risk
in reversing, reducing the risk of collision.

⚠ CAUTION
The reverse side assistance function is limited in some cases. For example,
 There are obstacles blocking. The system cannot detect objects behind other parked vehicles or
obstacles.
 The current vehicle speed is too high or too low.
 The driver steps on the accelerator pedal firmly.
 The driver turns the steering wheel quickly.

114
Traffic sign information
The traffic sign information function is used to recognize the traffic signs through the camera on the
front windshield and display them on the combination instrument to give a prompt to the driver.

39B727C42845
Traffic sign recognition
After the traffic sign recognition function is activated, the traffic sign can be recognized
and displayed on the combination instrument to remind the driver.

Overspeed alarm
After the traffic sign recognition function is activated, the overspeed alarm function
can be enabled. After the speed limit sign is recognized, in case of overspeed, the
system will give an alarm to remind the driver to reduce the speed to a suitable
range as soon as possible.

Speed alarm sensitivity

The alarm timing for overspeed can be set according to your driving habits.
 0 : Alarm will be issued when the vehicle speed reaches the speed limit.
 > 0 : Alarm will be issued only when the vehicle speed exceeds the speed limit.
 < 0 : Alarm will be issued in advance when the vehicle speed does not reach the speed limit.

Cruising speed limit function

After the traffic sign recognition function is enabled, the cruising speed limit function can be enabled.
When the vehicle is running in a cruise control mode, if the system recognizes a speed limit sign
showing the speed is ≥30 km/h and the cruising speed is higher than the speed limit of the sign, the
system will assist the driver to reduce the vehicle speed to be within the allowable maximum speed
limit.

⚠ WARNING
The traffic sign information function is designed to alert the driver to traffic signs and is not intended
to be used in all cases and is not a substitute for the driver's judgment on road speed limit messages.
In all cases, the driver is responsible for the safety of the vehicle and must always drive with care
and comply with applicable laws and road traffic regulations.

115
 ⚠ CAUTION
The traffic sign information function can work properly only when the speed sign is clearly visible.
It may not work properly or even not work in the following cases: For example:
 A sign fades.
 A sign is on the bend.
 The sign is not properly positioned.
 A flag is rotating or has been damaged.
 A sign is fully or partially blocked.
 A sign is fully or partially covered by frost, snow, dust, etc.
 A high-speed sign is placed in the position that is too far or too high.
 A speed limit caution or sign is attached to the road surface.
 Low visibility (such as rain, snow, fog and night etc.).
 The camera is illuminated by strong light or the illumination intensity changes suddenly.
 The front windshield around the camera is polluted, frozen, damaged or covered.
 If the vehicle is driving too close to the preceding vehicle, the camera detection scope is hindered.

NOTICE
 The speed limit sign identified by the system shows the default speed unit of xx km/h.
 For multiple speed limit values on the same speed limit sign, the system will show the maximum
value.
 When multiple speed limit signs are arranged in parallel, the system will display the maximum
speed limit value. Please take the actual speed limit value of the current lane as the criterion.
 When the vehicle is turning, the speed sign may not be identified.

116
Hill descent control system

Vehicle equipment When the power supply is set to ON mode or the

Please note that this manual contains all the engine is running, press the button to turn on or
standard equipment, country-specific equipment off HDC.
and special equipment for this model series.  After HDC is turned on, the HDC indicator
Thus, some equipment or features described light on the instrument cluster goes on.
in this manual may not be installed onto your  After HDC is turned off, the HDC indicator
vehicle or are only available in some markets. light on the instrument cluster goes off.
For further configuration information, please  When HDC is working, the HDC indicator light
refer to relevant sales information or consult on the instrument cluster flashes.
with your distributor selling the vehicle to you.
NOTICE
 It is recommended that HDC should be used
Hill descent control system
in a lower gear position.
introduction  HDC will automatically turn off when the
While going downhill, the hill descent control vehicle speed is greater than 60 km/h.
system (HDC) may actively brake to ensure  With HDC turned on, the speed can still be
that the driver can maintain a constant speed adjusted by depressing the brake pedal or
and drive downhill safely. the accelerator pedal.

⚠ WARNING
 HDC is intended only to be an aid. At all
times the driver should be responsible for
the safety of the vehicle, and always pay
attention to the surrounding traffic.
 In case of too high slope, the HDC may not
function and thus the vehicle can ’ t be
driven down the slope at even speed. At
this time, you can control the vehicle speed
by stepping on the brake pedal.

Instructions

F387743687FE

117
 Driving assist system

Vehicle equipment prevent wheels from locking to maintain steering

Please note that this manual contains all control of the vehicle.
the standard equipment, country-specific
equipment and special equipment for this ⚠ CAUTION
model series. Thus, some equipment or During emergency braking, do not step on the
features described in this manual may not brake pedal several times and gently. Otherwise, it
be installed onto your vehicle or are only will lengthen the braking distance.
available in some markets. For further The ABS is not designed to shorten the braking
configuration information, please refer to distance of the vehicle. Especially in the following
relevant sales information or consult with cases, compared with vehicles not equipped with
your distributor selling the vehicle to you. the ABS, your vehicle may require a longer
braking distance. Be sure to maintain adequate
Tips for safety safe distance from the vehicle in front of you:
 when driving on muddy, gravel or snowy road.
About traffic safety
 when driving with tyre chains in place.
Never take a risk in driving because the vehicle
 when driving on bumpy road.
is equipped with driving assist systems and
 when driving on potholes or uneven road.
always ensure that the vehicle speed and
driving style adapt to visibility, weather, road
The ABS may not work effectively:
and traffic conditions.
 when the limit of tyre grip performance is
exceeded (like using excessive wear tyre on
About modification
snowy road).
Suspension modification or use of tyres or
 when driving at a high speed on wet and slippery
wheels of non-specified size will impact
road.
driving assist systems and may cause
system malfunctions. Electronic braking force distribution
system
About sound and vibration The electronic braking force distribution (EBD)
 vibration may be created by some driving system is capable of automatically adjusting the
assist systems (such as ABS) during work or front and rear braking force ratio to enhance
the sound of the motor working may be braking efficiency. It complements the ABS for
heard, which does not indicate a greater braking stability and thereby vehicle
malfunction. stability.
 When you jump start the vehicle due to
drained battery power, the engine may Braking force assist system
not run smoothly and the warning lamps Stepping on brake pedal very quickly can trigger
of ABS or the ESC may be turned on, which the braking force assist system to help increase
results from the low battery voltage the braking effect and shorten the braking
instead of the failure of the ABS or the distance during emergency braking.
ESC.
Traction control system
Anti-lock brake system When you start or accelerate on a wet and slippery
During emergency braking, or when braking road, the traction control system (TCS) helps to
is applied during driving on wet and slippery keep a driving force and avoid driving wheel
road, the anti-lock brake system (ABS) helps spinning.

118
Rollover prevention system When ESC works, the ESC indicator on the
When the vehicle turns a corner, the rollover combination instrument flashes. Make sure to
prevention system (RMI) determines whether be careful at this time.
there is a risk of rollover by monitoring the
movement status of the vehicle. If any, RMI NOTICE
will decelerate one or more wheels to refrain Generally speaking, ESC is on throughout the
the vehicle from a rollover accident. drive. The system can be turned off only
under following special conditions:
 When driving with tyre chains in place.
Secondary collision mitigation
 When driving in deep snow or on soft
system
ground.
The secondary collision mitigation system
 When the vehicle is stuck and you need to
(SCM) will automatically apply the braking to
free it.
the vehicle after the first collision (airbag
Turn on ESC again upon finish of above
deployment) to reduce the vehicle speed or
conditions.
stop the vehicle, thereby reducing the chance
and injury of a second collision.
Turning on/off the system

HHC (Hill-start Hold Control)

When the driver starts on a slope and
releases the brake pedal, the hill-start hold
control (HHC) can maintain the braking force
for about 2 seconds to effectively avoid rolling.

⚠ WARNING
When starting on a slope greater than 30%,
the vehicle may still roll. Therefore, do not
BB66AF3DEE89
excessively rely on this function. Please pay
attention to the safety of driving. After the vehicle starts, press the ESC OFF
button.

Electronic power steering system The ESC OFF indicator on the combination
The electric power steering system can instrument will light up, indicating that the
adjust the power in real time by monitoring system is shut down.
the driving speed, so as to ensure the Press the button again to restart the ESC system.
portability of low-speed steering and the
stability of high-speed steering and enhance NOTICE
the sense of security. The ESC will automatically start in the following
conditions:
Electronic stabilization program  Every time you start the engine.
Electronic stability control (ESC) can help  The vehicle speed exceeds 85 km/h.
reduce the risk of side slip, and improve
driving stability by braking individual wheel
under certain driving situation.

119
Emission control system

Vehicle equipment ⚠ CAUTION

Please note that this manual contains all the To avoid damaging the catalytic converter,
standard equipment, country-specific equipment please pay attention to the following items:
and special equipment for this model series.  Do not use leaded gasoline or gasoline with
Thus, some equipment or features described in more than the standard amount of
this manual may not be installed onto your manganese or sulphur.
vehicle or are only available in some markets.  Do not drive the vehicle when the fuel level
For further configuration information, please is extremely low. If the fuel is exhausted, it
refer to relevant sales information or consult will cause the engine to misfire (this may
with your distributor selling the vehicle to you. be confirmed by unstable engine operation
or a loss of power), damaging the catalytic
Tips for safety converter.
The emission control system may vary with  Do not idle the engine at high speed for an
different engine models. For the particular extended time (5 minutes or longer).
equipment, please refer to the actual vehicle.  When a problem with the engine is indicated
Do not modify any part of the engine or (such as shutdown or performance
emission control system. degradation), please do not continue driving
the vehicle.
 Do not operate the engine with the spark
Oxygen sensor
plugs removed.
The oxygen sensor measures the concentration
 Do not start the vehicle by pushing or
of oxygen in the exhaust gases and reports that
pulling it.
information to the ECU in order to regulate the
 Do not add too much engine oil.
engine's fuel-air ratio for optimum combustion
 Please avoid striking the catalytic converter.
efficiency and to reduce the amount of carbon
monoxide, hydrocarbons, and nitrogen oxides
contained in the exhaust. Fuel evaporation control unit
When the vehicle is running normally, the fuel
evaporation control unit can make the fuel
Catalytic converter
steam enter the engine to burn, so as to prevent
The catalytic converter is the most important
the fuel steam from entering the atmosphere.
external purifier installed in the vehicle’s
exhaust system. The catalytic converter contains
Crankcase emission control unit
the metallic catalysts that convert harmful gases
The crankcase emission control unit guides
such as carbon monoxide, hydrocarbons, and
the mixed gases within the crankcase (such as
nitrogen oxides into harmless carbon dioxide,
uncombusted fuel vapours, water vapour, and
water, and nitrogen gas through oxidation and
exhaust) through a connected pipe into an
reduction reactions.
appropriate place in the air-intake pipe to
Do not disassemble the catalytic converter without
return them to the cylinders and be combusted
cause, as it does not require maintenance as long as
again. Thus, the exhaust gas can be reduced
it is used correctly. Be sure to choose a catalytic
while the engine fuel economy improved.
converter that matches the engine for replacement.

120
On-board diagnostic system
The engine malfunction warning lamp is part of
the vehicle's on-board diagnostic system.
The engine electronic control unit equipped
with the on-board diagnostic system stores
various fault information (especially when it
comes to exhaust-emissions fault information).
The fault information will be cleared if the
battery cables are disconnected, making a rapid
diagnosis difficult. Thus, please do not
disconnect the battery cables when investigating
why the engine malfunction warning lamp has
illuminated.

121
 Head-up display (HUD)

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

About the system

The head up display (HUD) can project relevant information to an effective visual area within the
driver's field of view. By using this system, the driver can check the vehicle information during
normal driving without lowering head, thereby avoiding distracting the driver’s attention from the
road ahead, and preventing the eye fatigue when the driver switches the angle of view while
observing the road ahead and the nearby instrument panel.

NOTICE
 Under certain special weather conditions (such as rain, snow, strong sunlight, etc.), the
information displayed on HUD may be unclear or disturbed.
 Certain sunglasses can affect information reading.

How to use
After the vehicle is started, the head up display (HUD) can be turned on or off via
[Vehicle Settings] [ In-Car] → [HUD] on the multimedia display screen.

192126CDD40D
After the HUD is turned on, you can configure the following settings:
 Set the display content of HUD projection interface.
 Adjust the projection height, angle or brightness of HUD with steering wheel.

122
Virtual instrument

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Summary

C55F0CA0EE4A
(A) Water temperature gauge (G) Power meter
(B) Digital clock (H) Mileage
(C) Information center (I) Gear position display
(D) Multi-function tab bar (J) Driving mode
(E) Outside temperature (K) Speedometer
(F) Fuel gauge

Water temperature gauge

Display an approximation of the engine coolant temperature.

⚠ CAUTION
When the water temperature is close to the red warning zone, slow down your vehicle immediately
and find a safe spot to park your vehicle for checks. Restart the engine only after water temperature
in the engine has returned to normal.

123
 Fuel gauge
Display the amount of fuel remaining in the fuel tank.

NOTICE
When driving for an extended time on a slope or around a bend, the fuel-gauge needle may become
unstable as fuel moves around in the tank.

Power meter
It displays the total power the vehicle input currently or the energy recovery power.
Speedometer
Display the current speed of the vehicle.
Information center
Switch the displayed content through the multi-function tab bar.
Multi-function tab bar
Select different function tabs to switch the content displayed on the multi-information display.

Tab Meaning Information center

It displays the mileage, vehicle speed, fuel consumption, journey
Driving data
time and other information related to vehicle operation.

Audio media It displays the audio media information that is currently playing.

BT phone It displays the information about the currently connected BT phone.

Navigation
It displays the map and navigation information
information
Alarm It displays the currently shielded primary alarm messages or the
messages automatically hidden secondary alarm messages.
The menu setting information can be displayed, and the instrument
Menu setting
can be set accordingly.

NOTICE
The audio media tab may be different based on the media source of the currently playing audio.

124
Virtual instrument

Steering wheel button  Digital speed: it shows the current driving

speed in digital form in case the instrument
is using dynamic theme.
 Driving efficiency: it displays the economic
status of the vehicle in the current driving
mode.
 Energy flow: it displays the working state of
the power system and the state of charge
of the power battery under the current
working condition.
 Tripmeter: it shows the mileage since the
C191FAD95231
last reset.
(A Back button
 Driving time: it shows the driving time since
(B) Page-turn button
the last reset.
(C) OK button
 The driving time will automatically reset
when it exceeds 99 hours 59 minutes.
Back button  Average speed: it shows the average
Press the button to return to the previous menu. vehicle speed since the last reset.
Press this button to switch the functions of the  Average fuel: it shows the average fuel
multi-function tab bar if there is no previous consumption since the last reset. Instant
menu. fuel: it shows the current fuel consumption
Page-turn button information. This information can help you
If multiple pages or options are displayed on the to adjust your driving behavior to achieve
multi-information display, your desired fuel consumption level.
press this button to turn pages to view or switch  Range: it displays a prediction of approximately
options. how far the vehicle can be driven based on
OK button the current fuel consumption in the fuel tank.
Press this button to enter the next menu, confirm  It shows "---" when the range is less than 50
the current settings or shield the primary alarm km.
messages currently shown.
Press and hold this button to temporarily shield NOTICE
all alarm messages currently shown or reset  After refuelling, the range will be recalculated.
certain driving data interfaces.  The actual driving distance will vary depending
on driving habits and road conditions.
Driving data interface  When the warning light on the instrument
cluster illuminates, you should refuel even if
Press the Back button on the steering wheel
the display shows that the vehicle can travel
to switch to the driving data interface.
farther.
Press the Up button  or Down button  on the
 TPMS: it shows the tyre pressure and
steering wheel to switch the driving data shown
temperature values.
on the multi-information display.
 Tachometer: it displays the current engine
speed.

125
 NOTICE Press the OK button on the steering wheel to
The average fuel consumption, average vehicle dial the number of the currently selected
speed, tripmeter and driving time are displayed contact.
on two data interfaces, i.e., A and B.
 On the data interface A, the driving data Navigation information interface
within the current ignition cycle is displayed, Press the back button on the steering
and the power supply mode is turned to the wheel to switch to the Navigation information
OFF position; after 4 hours, the data will be interface .
automatically reset. Press the up button  or down button  on
 On the data interface B, the driving data from the steering wheel to switch the can switch
the last manual reset to the current time is between of the navigation information interface.
displayed.
 Press the OK button on the steering wheel Alarm information interface
when the tripmeter, average fuel consumption,
Press the Back button on the steering
average vehicle speed or driving time is shown
wheel to switch to the alarm information
on the multi-information display to switch
interface.
between the data interface A and the data
Press the Up button  or Down button  to
interface B.
view all the currently shielded primary alarm
 Press and hold the OK button on the steering
messages and the automatically hidden
wheel when the tripmeter, average fuel
secondary alarm messages.
consumption, average vehicle speed or
Most alarm messages are accompanied by a
journey time is shown on the multi-
corresponding alarm indicator light on the
information display to manually reset the
instrument cluster. When an alarm message is
corresponding data on the data interface A or
displayed, the corresponding alarm indicator
B.
light also turns on.
The alarm prompt message has priority over
Audio media interface the driving data, and will be displayed first
Press the back button on the steering wheel when the power supply mode is turned to ON.
to switch to the audio media interface. At this Please perform all and any operations strictly
time, the multi-information display will show in accordance with instructions contained in
the media information that is currently playing. alarm messages. If there are no relevant
instructions available, please stop the vehicle
BT phone interface for checks or contact authorised service
Press the back button on the steering wheel centre for assistance.
to switch to the BT phone interface.
At this time, the multi-information display will ⚠ CAUTION
show the call log information.  Do not ignore alarm prompt messages.
Press the up button  or down button  on the Failure to heed alarm messages can cause
steering wheel to switch the selected call log severe damage to the vehicle.
entry.  If an alarm indicator light goes on, please
stop the vehicle as soon as possible and
contact authorized service centre, while
paying extra care to safe driving.

126
 When the driving speed reaches or exceeds
Important alarm messages
the set value, a warning of over speed will
If there are multiple important alarm messages,
appear on the combination instrument to
they will be shown cyclically in turns. After an
show an alert to drive safely.
alarm condition is cancelled,
the corresponding alarm message will not be
shown at the same time. Theme settings
Pressing the [OK] button on the steering wheel The theme style of the instrument can be set.
can shield important alarm messages (pressing
the button can shield the important alarm Driving data settings
messages currently shown, while pressing and You can set certain driving data on the multi-
holding the button can shield all important information display to be hidden or displayed.
alarm messages), and will be shown on the All data of the average fuel consumption,
instrument cluster to remind you that the alarm average vehicle speed, tripmeter and journey
messages have not been released. time can be cleared.

Secondary alarm messages Alarm volume

Secondary alarm messages will disappear You can set the alarm volume.
automatically after being shown for a few
seconds. will be shown on the instrument Unit settings
cluster to remind you that the alarm messages You can set the unit of the mileage & fuel, the
have not been released. pressure, and the temperature.

Menu setting interface Language settings

Press the back button on the steering wheel to You can set the display language of the
switch to the menu settings interface. combination instrument.
Press the up button  or down button  on the
steering wheel to scroll through the menu Reset to factory
settings term by term. Part of the menu settings of the combination
Press the OK button on the steering wheel to instrument can be restored to
enter the next menu or to confirm the current the factory default state.
setting.
Maintenance miles
Overspeed settings You can check the mileage to the next
Press the OK button to enable or disable the maintenance.
speed alarm function. This information is only used to remind you
After enabling the speed alarm function, press to maintain your vehicle in time.
the up button  or down button  to adjust the
speed alarm value.

127
Indicator lights on the instrument

Vehicle equipment ⚠ WARNING

Please note that this manual contains all the Do not ignore any alarm. Otherwise,
standard equipment, country-specific equipment serious damage to the vehicle or an
and special equipment for this model series. accident may be caused.
Thus, some equipment or features described in
this manual may not be installed onto your NOTICE
vehicle or are only available in some markets.  The secondary alarm will be
For further configuration information, please automatically shielded after being
refer to relevant sales information or consult displayed on the multiinformation
with your distributor selling the vehicle to you. display of the instrument panel for
a few seconds.
Indicator lights on the instrument  All current alarms of the vehicle
NOTICE can be checked on the alarm
 When the power supply is switched ON, interface of the instrument panel.
some indicator lights or warning lights will
illuminate for a short time, indicating that Turn signal indicator lights
the system self-test is in progress, which is When the left turn signal lamp is on,
normal. Depending on the model the left turn signal indicator light
configuration, not all indicator lights or will flash. When the right turn signal
warning lights on the instrument cluster will lamp is on, the right turn signal
illuminate. indicator light will flash. When the
hazard warning light is on, the turn
Primary alarm indicator light signal indicator light and all exterior
When this light goes on, an important turn signal lamps will flash together.
alarm is currently present in the vehicle
and at least one important alarm is ⚠ CAUTION
manually shielded. When the turn signal indicator light
flashes quickly, it usually means
⚠ WARNING that the turn signal lamp has been
Do not ignore any alarm. Otherwise, damaged. Replace it as soon as
serious damage to the vehicle or an possible. Otherwise, other drivers
accident may be caused. on the road will not be able to see
your turn signals.
NOTICE
All current alarms of the vehicle can be Light on indicator light
checked on the alarm interface of the When this light goes on, the main
instrument panel. lighting switch is turned on.

Secondary alarm indicator light Position indicator light

When this light goes on, a secondary When this light goes on, position
alarm is currently present in the vehicle. lamps and license plate lamps are on.

128
High beam indicator light When this light flashes for a period of
When this light goes on, the high time and then lights up, the tyre pressure
beam headlamps are on. monitoring system is malfunctioning,
which is accompanied by several
Front fog lamp indicator light audible warnings.
When this light goes on, the front fog
lamps are on. ⚠ WARNING
If this light is on, you should avoid
Rear fog lamp indicator light sharp turns or emergency braking,
When this light goes on, the rear fog and drive the vehicle to a safe place
lamps are on. as soon as possible, and stop for
inspection.
Seat belt unfastened warning Driving a vehicle when the tyre
pressure is too low or the tyre
light
temperature is too high will increase
When this light goes on, the driver, the
the possibility of tyre failure, and may
front passenger, or rear occupants are
even cause serious damage to the
not wearing seat belts.
vehicle or lead to an accident.

Door open warning light

Parking brake indicator light
When this light goes on, the door or
When this light goes on, the parking
the engine hood is open or not
brake is applied. When this light
properly closed.
flashes, the brake disc temperature is
too high or the road slope is too large.
120km/h alarm indicator light
In this case, there is a risk of vehicle
When this light goes on, the vehicle
rolling. Depress the brake pedal and
speed is over 120 km/h.
stop the vehicle on a flat road as
soon as possible.
Airbag fault warning light
When this light goes on, the airbag Parking brake fault warning light
system is malfunctioning. In this case, When this light goes on, the electric
go to the authorised service centre as parking brake system is malfunctioning.
soon as possible for inspection and
repair.
AVH (Automatic Vehicle Hold)
indicator light
Tyre pressure monitoring system
When this light is on and yellow, the
warning light automatic vehicle hold is turned on
When this light goes on, the tyre has and in standby status.
low pressure or high temperature, When this light is on and green, the
which is accompanied by an audible automatic vehicle hold is turned on
warning. At this time, stop the vehicle and in working status.
for inspections and contact the
authorised service centre.

129
 Anti-lock brake system fault Electric power steering system
warning light failure warning light
When this light goes on, the ABS is When this light goes on and yellow,
malfunctioning. the steering assist effect is reduced,
At this time, contact the authorised so more force is required to operate
service centre. the steering wheel. If this light
When this light goes on, the vehicle remains on after the vehicle is
can still be braked normally although restarted or after a short running
the anti-lock function is not distance, go to the authorised
available. service centre as soon as possible
for inspection and repair.
Brake system fault warning light When this light goes on and red, the
When this light goes on, the brake electric power steering system is
fluid level is too low or there is a malfunctioning, and steering
malfunction in the braking force assistance is no longer working. In
distribution system. this case, park the vehicle in a safe
In this case, immediately stop the place and turn off the vehicle, and
vehicle in a safe spot and contact the then restart the vehicle within
authorised service centre. Otherwise, a several minutes. If the indicator light
serious accident may be caused. remains on, go to the authorised
service centre as soon as possible
Electronic stability control for inspection and repair.
indicator light
When this light flashes, the ESP is in ⚠ WARNING
working status. When this light goes on and red, the
When this light goes on, the electronic electric power steering system stops
stability control system fails. functioning. In such a situation, you
need greater force to steer the
vehicle. Go to an authorised service
Electronic stability control off
centre as soon as possible for service.
indicator light
When this light goes on, the
Water temperature warning light
ESC is turned off.
When this light goes on, the water
temperature of the engine cooling
Hill descent control indicator system is excessively high. In this
light case, stop the vehicle immediately
When this light goes on, the hill for inspection and repair. Otherwise,
descent control system is activated the engine may be damaged.
and ready for use.
When this light flashes, the hill Low fuel level warning light
descent control system is working. When this light goes on, the fuel is
insufficient.
On slopes or during turning, , the light

130
may go on prematurely due to unstable Engine maintenance warning
due to unstable fuel levels inside the light
fuel tank. When this light goes on, the engine
has a fault not related to the emission.
⚠ CAUTION At this time, contact the authorised
Do not drive the vehicle when the service centre.
remaining fuel level is extremely low.
Otherwise, the emission control
Engine oil pressure warning
system and powertrain system may
light
be damaged due to running out of
When this light goes on, the oil is
the fuel.
insufficient. In this case, park the
vehicle in a safe spot as soon as
Engine fault warning light
possible and shut down the engine.
If the light goes on after the engine is
Otherwise, the engine parts may be
started, the engine has a fault that
seriously damaged. Check the oil
affects emissions.
level after a few minutes and add oil
At this time, contact the authorised
if necessary. If the oil level is normal
service centre.
and the light is still on, contact a
authorised service centre.
NOTICE
 Failure of some control systems of
Charging warning light
the vehicle (e. g. loss of communication
If the light goes on after the engine
signal of hybrid system or charging
is started, there is a malfunction in
system, etc.) may also cause this
the battery charging system. In this
warning light to illuminate. If this
case, go to the authorised service
warning light goes on, stop at a safe
centre as soon as possible for
place as soon as possible, switch the
inspection and repair.
power mode to OFF mode, then
restart the vehicle and check this Automatic transmission
warning light. If the warning light is
overheat warning light
still on, it is recommended to go to
When this light goes on, the automatic
the authorised service centre for
transmission fluid temperature is
inspection as soon as possible.
too high (when the vehicle is
Please drive carefully and avoid high
started frequently on the ramp or
speed before identifying the
when the accelerate pedal is fully
malfunction.
stepped etc., this light may be on).
If this indicator light illuminates
At this point, park the vehicle in a
frequently, it is recommended to go
safe location as soon as possible to
to the authorised service centre for
run at an idle speed and apply the
inspection even if the light goes out
parking brake to cool the transmission.
after following the preceding steps.
If the light stays on after the above
 The fuel tank cap not being properly
handling, contact the authorised
installed may also cause this light to
service centre.
illuminate.

131
 Adaptive cruise control indicator Rear side assist system warning
light light
When this light goes on and white, the When this light goes on and yellow,
adaptive cruise control function is the sensor for the rear side assist
turned on and in standby status. system is blocked. In this case, check
When this light goes on and green, the both the inside and outside of the
adaptive cruise control function is rear bumper on both sides for any
turned on and the cruising speed is obstructions and clear them away.
set successfully. When this light goes on and red, the
rear side assist system is malfunctioning.
Adaptive cruise control system In this case, do not use the rear side
fault warning light assist system, and go to the authorized
When this light goes on, the adaptive service centre as soon as possible for
cruise control system is faulty. In this inspection and repair.
case, do not use the adaptive cruise
control function, and go to the Doubling assistance indicator
authorised service centre as soon as light
possible for inspection and repair. When this light goes on, the doubling
assistance function is turned on.
Intelligent cruise control
indicator light Reverse side warning indicator
When this light goes on and white, the light
intelligent cruise control function is When this light goes on, the reverse
activated and ready for use. side warning function is enabled.
When this light goes on and green,
the intelligent cruise control function is Lane departure indicator light
activated and the cruising speed is set When this light goes on and green,
successfully. the lane departure warning function
When this light goes on and red, a fault is turned on. When this light goes on
in the intelligent cruise control assist and red, the lane departure warning
system. In this case, do not use the function is malfunctioning.
intelligent cruise control function, and In this case, do not use this function,
go to the authorised service centre as and go to the authorized service centre
soon as possible for inspection and as soon as possible for inspection and
repair. repair.

Lane keep assist indicator light

When this light goes on and green, the
lane keep assist function is turned on.
When this light goes on and red, the lane
keep assist function is malfunctioning.

132
Collision safety assist indicator Power system fault warning light
light When this light goes on and yellow,
When this light goes on and green, the the vehicle power system is
collision safety assist function has malfunctioning.
been activated and is able to work In this case, immediately stop the
normally. When this light goes on and vehicle in a safe spot and contact the
red, something is wrong with the authorised service centre. When this
collision safety assist function. In this light goes on and red, the vehicle
case, go to the authorized service power system has a serious fault,
centre as soon as possible for and the vehicle cannot continue
inspection and repair. driving. At this time, contact the
authorized service centre.
READY indicator light
Motor malfunction warning
When this light goes on, the vehicle is
started and ready for normal driving. light
When this light goes on, the drive
motor system is malfunctioning. At
EV indicator light
this time, contact the authorised
When this light goes on, the vehicle is
service centre.
only using electric power and the
engine is not running.
E-Park fault indicator light
When this light goes on, the gear P
Power reduction indicator Light
controller is malfunctioning.
When this light goes on, the vehicle has
a fault that affects the vehicle power
output. At this time, the vehicle power is Brake energy recovery fault
reduced and the speed will be limited. indicator light
When this light goes on, the braking
Low power battery level indicator energy recovery function is
malfunctioning.
light
When this light goes on, the power
battery is too low and must be charged One pedal mode indicator light
soon. When this light goes on, the one
pedal mode is turned on.

Power battery fault warning light

When this light goes on and yellow, the
power battery has a minor fault. When
this light goes on and red, the power
battery has a serious fault, and the
power system will be powered off in an
emergency.

133
Power supply management system

down unnecessary electrical equipment according

Vehicle equipment
to the battery monitoring information, so as to
Please note that this manual contains all the
avoid a large amount of battery discharge
standard equipment, country-specific equipment and
and ensure the starting performance of the
special equipment for this model series. Thus,
vehicle.
some equipment or features described in this
manual may not be installed onto your vehicle
or are only available in some markets. For further  Dynamic Power Management
configuration information, please refer to Continuously monitor the power consumption
relevant sales information or consult with your of each electrical equipment during the
distributor selling the vehicle to you. driving of the vehicle, and distribute the
power generated by the generator to
different electrical equipment as needed.
System introduction
When the generator generates more power
The power management system can monitor the
than the demand of the electrical equipment,
power consumption of each electrical equipment in
the dynamic power management system
the vehicle and allocate the power reasonably to
will regulate and supply power to the
improve the starting performance of the vehicle
battery to allow it to reach the optimum
and extend the service life of the battery.
charging status.
The power management system mainly has the
following functions:
NOTICE
 Battery Monitoring
It is impossible for a power management system
The current remaining power and health
to go beyond the boundaries of physical law.
degree of the battery can be calculated
Please note that there are limits to the power
accordingly as the voltage, current and
and service life of the battery.
temperature of the battery are continuously
monitored by sensors.
Information you should know
 Sleep power management The power management system will give top
Continuously monitor the power consumption priority to ensuring the starting performance
of various electrical equipment during the of the vehicle.
parking period of the vehicle, and gradually In the event of short-distance traveling, and driving
shut down unnecessary electrical equipment in urban areas and under low temperatures,
according to the battery monitoring information, the power consumption will increase, and the
so as to avoid a large amount of battery discharge generator will supply less power. If the vehicle
and ensure the starting performance of the is not started, the use of electrical equipment
vehicle. will directly consume the power of the battery
because the generator cannot supplement
 Static power management power in this case.
Continuously monitor the power consumption of In these situations, the power management
various electrical equipment when the system will operate to control the power
vehicle is not started up, and gradually shut distribution.

134
Parking the vehicle for a long time In order to restore necessary power supply, the
If the vehicle is not driven for several days or system will temporarily shut down certain electrical
weeks, the power management system will equipment with high power consumption or
gradually turn off the electrical equipment or reduce the power consumption of these
reduce the electrical energy being used by the equipment. Especially, the heating system
electrical equipment, so as to reduce power consumes a considerable amount of energy. If
consumption and maintain the vehicle's starting it is found that the seat heating function is
performance for a longer time. inoperative or the air volume of the air
If the vehicle has been parked for a long time, conditioning is limited, it means that the
certain convenient functions (such as remote system has temporarily turned those functions
unlocking, etc.) may not be available. After off or adjusted them to operate at a lower
starting the vehicle, these functions will be power. When the power is sufficient again,
restored. these systems can be used normally again.

When the engine is shut down.

For example, if you listen to the radio or use
other functions of the audio/visual system with
the engine off, the battery will discharge.
If the battery power consumption affects
vehicle startup, a message will display on the
multimedia display screen or the combination
instrument. If you want to use these functions
normally, please start the engine.

When the engine is running

During driving, even if the generator can
provide electricity, the battery may lose power.
This situation is prone to occur when the power
consumption is too large and the generator
provides less power, especially when the
battery power capacity is low.

135
136
3 Audiovisual system
Safety prompt 138
Panel 139
Display screen 141
Interface introduction 142

137
Safety prompt

 When cleaning the display screen, do not use

Vehicle equipment
abrasive wipers or detergent containing
Please note that this manual contains all the
organic solvent.
standard equipment, country-specific equipment
 Do not strike the screen when image jitter
and special equipment for this model series.
occurs in process of operation.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets. About the radio
For further configuration information, please When driving the car, you may not find any radio
refer to relevant sales information or consult stations, or you may hear noises or receive
with your distributor selling the vehicle to you. different radio signals with same frequency,
depending on the environment such as road
Safety conditions, weather, etc.
 Ensure that your use of any of the system's
features does not distract you and thereby About USB storage devices
interfere with safe driving. Your most Since there are various types of USB storage
important responsibility while driving is for devices, this system may not be compatible with
the safety of the drive. You must obey all all USB storage devices.
traffic regulations.
 During driving, the driver is not allowed to About Bluetooth
operate the system and must keep the  Since there are a great number of smartphone
volume of the system at an appropriate brands with different functions, this system
level, so as not to affect driving safety due may not be compatible with all the
to lack of concentration. smartphones.
 This system may only be used in areas  If you cannot search and find the Bluetooth
permitted by law. Some national or local device name of this system during Bluetooth
regulations may prohibit use of the display pairing, restart the Bluetooth on the smartphone
screen within the driver's field of view. and search it again.
 Do not disassemble or modify the system.  If Bluetooth cannot be connected, delete the
 When a failure occurs, stop using the system paired device on the smartphone, and pair it
and contact authorised service centre. Do not again.
try to repair the system by yourself.  If Bluetooth does not function properly when
in use, disconnect the Bluetooth and reconnect
About the use it.
 For safety reasons, some functions may not
be activated when the vehicle starts to move.
 Do not press the buttons or knobs on the
panel firmly.
 Do not press the screen forcefully or scratch
it with sharp objects.

138
Panel

Vehicle equipment Media switching button

Please note that this manual contains all the Press the [M] button to switch to media audio
standard equipment, country-specific equipment and sources.
special equipment for this model series. Thus,
some equipment or features described in this Bluetooth phone button
manual may not be installed onto your vehicle or After connecting and activating Apple CarPlay
are only available in some markets. For further or Android Auto, you can answer or hang up
configuration information, please refer to relevant the phone via the Bluetooth phone button.
sales information or consult with your distributor
selling the vehicle to you. Power supply switch
Type I
Steering wheel buttons

51011A10EE18
 Press the button to enter or exit the mute mode.
D6321AC3A6D5
 Press and hold the button (for more than 3
Ⓐ Voice button
seconds) to enter the standby mode, touch
Ⓑ Volume+ button
Ⓒ Previous track/radio button the multimedia display, and exit the screen
off mode.
Ⓓ Volume- button
Ⓔ Bluetooth phone button  Press and hold the button for more than 8
seconds to restart the multimedia system.
Ⓕ Next track/ radio button
Ⓖ Media switching button
Type II
Voice button
After connecting and turning on Apple CarPlay or
Android Auto, press the voice button to
activate the voice function.

NOTICE
Depending on vehicle configuration, this function
may not be provided for your vehicle. Please refer
to the actual vehicle.
DC725A7EFFA8

139
 Press the button to enter or exit the mute mode. Media specifications
 Press and hold the button (for more than 3 This system supports the following media
seconds) to enter the standby mode, touch specifications:
the multimedia display, and exit the screen Media Specification
off mode. USB USB devices with a partition
 Press and hold the button for more than 8 device format of FAT32/NTFS/ExFAT.
seconds to restart the multimedia system. Supports Bluetooth 4.2
(Bluetooth 4.2,
External devices compatible with 2.1
and 3.0, supports low power of
USB interface Bluetooth
Bluetooth), and supports
Android Bluetooth protocol
versions: A2DP 1.3, AVRCP 1.6,
HFP 1.6, PBAP 1.2.

ประเภทไฟล์
ระบบนี้สนับสนุนประเภทไฟล์ดังต่อไปนี้
File Format
MP3, WMA, AAC, AAC Plus,
Audio
WAV, FLAC, APE, OGG
3E45280C9209 MP4, MOV, 3GP, WMV/VC-1,
Video
The interface with icon can be inserted into U AVI, MPG, MKV, WebM
disk to play multimedia, and connected to mobile
phone, etc. NOTICE
The interface with icon can be inserted into the Even files in formats supported by this system
U disk to play multimedia, and used to upgrade may not be normally played due to file
the system, etc. characteristics (such as file quality, bit rate,
frame rate, resolution, compression quality, or
NOTICE corruption), playing environment and storage
devices.
 Due to different vehicle configurations, USB
interfaces of some models may be installed in
the hollow place on the right side of the
auxiliary instrument panel. Please refer to the
actual vehicle.
 Ensure a stable connection between the
external device and the input port.
 Do not plug and unplug the device at will
during playing to avoid problems such as the
system not being able to recognize the device
normally.

140
Display screen

Vehicle equipment Display screen status bar

Please note that this manual contains all the The status bar icons are displayed at the top
standard equipment, country-specific equipment and of the central display screen to display the
special equipment for this model series. Thus, status of each function.
some equipment or features described in this The status bar icons will change in real time
manual may not be installed onto your vehicle according to functional characteristics, signal
or are only available in some markets. For further strength, connection status, switch status, etc.
configuration information, please refer to Icon Function status
relevant sales information or consult with your
distributor selling the vehicle to you. Time display

Display screen operation Signal of the vehicle network

You can complete functions such as selecting a is changed according to the
target, scrolling the list, or moving an application network status
by touching, sliding, and dragging on the central WIFI is connected and the
display screen. signal intensity can be
Gesture Opearation Result displayed

Select or enable a Mute mode on

Tap
function
Scroll view or Sound mode on
Tap and
move between Bluetooth is not
drag
pages connected
Tap with
Two fingers Zoom in Bluetooth is connected
and expand
USB device is connected
Tap with
two fingers Zoom out Wireless charging
and pinch not performed

Wireless charging in progress

Wireless charging
completed

141
 Interface introduction

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Mene interface
NOTICE
The screen display information (including images, icons, text and so on) shown in the manual is only
for instructions. The information displayed may vary with the vehicle configuration, software
version, themes and settings. Refer to the actual vehicle for specific information.

Type 1
In most interfaces, touch the menu button to show the menu application interface.
The system enters the navigation system by default after power-up. In the other interface, touch the
home button to switch to the navigation interface.

7D379FD3FF1B
The small windows of recently used applications are displayed on the top. Touch the small
application window to quickly switch to the application interface.
The application icons are displayed at the bottom. Touch the application icon to switch to application
interface.

142
Type II
In most interfaces, touch the menu button to show the menu application interface.

888DFD6DC66A
Vehicle Settings
Touch the [Vehicle Settings] button to switch to the vehicle settings interface where the function
and switch states of the vehicle can be set.

System Setting
Touch the [System Setting] button to switch to the setting interface, where the Bluetooth, Internet,
sound, display and so on can be set.

Telephone
Touch the [Telephone] button to switch to telephone interface. If other Bluetooth devices are not
connected, go to the [System Setting] → [Bluetooth] interface to activate the Bluetooth for pairing
and connection.
After pairing with other Bluetooth, functions such as dialling and answering calls, checking contacts,
call records and SMS can be realized.

NOTICE
 For pairing and connecting, please allow access to contacts, call records, messages and other
permissions on the mobile phone. Otherwise, these functions cannot be used.
 Message function is not supported by certain phones due to permission restrictions version
systems.

143
 NOTICE
 This communication device conforms to standards or technical requirements of NBTC.
 The electromagnetic field intensity of this communication device conforms to Safety Standard
for People to Use Communication Device Healthily published by National Telecommunications
Commission.

Apple CarPlay
Connect the iPhone to the on-board USB1 (with the icon ) interface through the mobile phone USB
data cable. Touch the [Apple CarPlay] button to switch to the Apple CarPlay interface. Disconnect
the USB cable to exit from the Apple CarPlay.

NOTICE
 Due to the different compatibilities of mobile phone systems and versions, some iPhones may not
support the Apple CarPlay function.
 When an Apple CarPlay device is connected, the Bluetooth phone function is disabled, and the
Apple CarPlay phone function can be used at this time.

Android Auto
Connect the Android phone to the on-board USB1 (with the icon) interface through the phone USB
data cable. Touch the [Android Auto] button to switch to the Android Auto interface.
Disconnect the USB cable to exit Android Auto.

NOTICE
 If the Android Auto application is not installed on your Android phone, download it from the
Google Play application store and install it on your phone.
 Due to the different compatibilities of mobile phone systems and versions, some Android phones
may not support the Android Auto function.
 When an Android Auto device is connected, the Bluetooth phone function is disabled, and the
Android Auto phone function can be used at this time.

Local Media
Touch [Local Media] to switch to local media interface which includes local radio, Bluetooth music,
USB music and USB video.
Pair the system Bluetooth with other audio playback devices to play Bluetooth music on the
[System Setting][WIFI] interface.
Insert the USB device which is used to store media documents into USB connector on vehicle to play
USB music and USB video.

Personal Center
Touch [Personal Center] button to switch to the system setting interface, where you can log into the
account, set account information, switch account and so on.

144
Message Center
Touch the [Message Center] button to switch to message center interface where you can check
related messages.

Online Music
Touch the [Online Music] button to switch to online multimedia interface where search or select
favorite media after connected to the network.

Energy Consumption Assistant

Touch the [Energy Consumption Assistant] button to switch to consumption assistant interface
where you can check consumption information, driving suggestions and related settings.

Shortcut panel
In most interfaces, sliding down from the top of the screen will call up the shortcut panel.

Type I

0309A6F3632A
Type II

86D88E11CE10

145
 Volume/brightness adjustment
Touch and drag the slider to adjust the corresponding volume or brightness
Touch the mute button to enable or disable the navigation mute function.
Touch the button to activate or deactivate the mute function of the media.
Touch the button to activate or deactivate the automatic brightness adjustment function.

Shortcut switch
Touch the switch directly to execute, switch to, turn on or turn off the corresponding function.
You can edit and replace the shortcut switch displayed.

Interconnection
System description
The system can ensure the sharing of mobile phone applications with the on-board multimedia host,
mainly including navigation, music, talkback, phone calls, voice recognition, etc. This can ensure you
have a safer and more convenient vehicle experience.

NOTICE
 Some mobile phone system versions may not support the interconnection function.
 Due to the different systems and version compatibility, even the system version that is supported
by the mobile phone may not support the interconnection.

Connection method
1. Download and install the APP on the mobile phone, open the APP, and enter the driving mode.
2. Connect the mobile phone with the on-board USB1(with the icon) interface through the USB
data cable.
3. Touch the button on the multimedia display screen, and activate the interconnection by
following the prompts. If the APP is not installed on the mobile phone, a QR code will be shown.
You can scan the QR code with your mobile phone to download the APP.

NOTICE
 Some mobile phones need to have USB debugging mode turned on for successful interconnection.
 Some functions of interconnection (such as call function) are available only when mobile phone
Bluetooth and car Bluetooth are successfully connected.
 When mobile interconnection function of mobile phone is enabled, the screen of mobile phone
will be dimmed to save the power of mobile phone.

Exit method
Disconnect the USB cable to exit the interconnection.

NOTICE
 To achieve a better customer experience, the application will be constantly updated.
 Some functions require information that is obtained from the Internet, and data traffic may occur
in this process.

146
 NOTICE
 This communication device conforms to standards or technical requirements of NBTC.
 The electromagnetic field intensity of this communication device conforms to Safety Standard
for People to Use Communication Device Healthily published by National Telecommunications
Commission.

System Setting
In the menu interface, touch the [System Setting] button to switch to the system setting interface.

Bluetooth
Type I

79E9E13CE8A5
Type II

9BF072464DEB

 [ Bluetooth ]: touch the Bluetooth switch of this system to turn on or off the Bluetooth.
 [ Bluetooth Visible ]: after this switch is turned on, other devices are allowed to detect the
Bluetooth of this system and perform pairing connection.
 [ BT Name ]: it displays the name of the Bluetooth device, which can be modified to a custom
name.

147
  [ Device Name ]: it displays the name of the Bluetooth device.
 [ Pairing History ]: it can display other Bluetooth devices currently connected, and you can
disconnect or delete the paired device.
 [ Pairable Device ]: it displays the Bluetooth devices searched for. Touch the name of the
Bluetooth device you searched for to initiate a pairing request. Touch the [Search] button to
search for Bluetooth devices again.

NOTICE
 This communication device conforms to standards or technical requirements of NBTC.
 The electromagnetic field intensity of this communication device conforms to Safety Standard
for People to Use Communication Device Healthily published by National Telecommunications
Commission

WIFI

9A0EA3E7CBFE
 [ WIFI ]: touch the WIFI switch of this system to turn on or turn off the WIFI.
 [ Networks ]: after WIFI is turned on, you can display searched available network, and touch the
network name in the list to connect.
With connected normally, this network can be displayed at [ Connected ], and touch [ Disconnect ]
to disconnect current network.

NOTICE
 This communication device conforms to standards or technical requirements of NBTC.
 The electromagnetic field intensity of this communication device conforms to Safety Standard
for People to Use Communication Device Healthily published by National Telecommunications
Commission.

148
Sound
Type I

2D89A9391E20
Type II

CD355506E718
 [ System Sound ] : the navigation prompt sound, voice volume, media volume, call volume,
vehicle alarm sound, speed sound compensation and so on.
 [ Effect Setup ] / [ Sound effect Setting ]: you can set the DTS sound effect, the equalizer, the sound
field and so on.

149
 Display
Type I

78D2B143E52B
Type II

F156BCB44039
The brightness mode, centre-controller brightness, time display format, driving video limit,
language, unit setting and so on can be set.

Customize

54B94F1A156F
The wake-up words of voice assistant can be set.

150
System
Type I

006B8315E470
Type II

435643A07DAD
 [ Privacy ]: the system can collect and store personal and vehicle data for providing
 better vehicle network service. It can be turned on or off optionally.
 [ Version ]: you can view and modify the name of this device, view the software version, update the
system through WIFI/4G check and update, and update and update through the USB device.

NOTICE
Depending on the vehicle configurations, some features may not be fitted to your vehicle.
Please refer to the actual vehicle.

 [ Reset System Settings ]: the system settings can be reset.

 [ Restore Factory Settings ]: the system can be restored to factory default state.
 [ Log Upload ]: the log data can be uploaded.

151
 NOTICE
About upgrades:
 To ensure safety during the upgrade process, place the vehicle in a safe environment.
 For ensuring successful upgrade, please keep the ignition switch in ON mode (READY indicator
light off), apply the parking brake, keep the vehicle in stationary status and shut down high-
power electrical appliances (such as A/C, lamps, speakers and so on).
 During the update process, read the licence agreement on the download page and the precautions
on the installation page carefully. To learn more about the update, click update details to view.
 During the update process, all functions of the vehicle will be unavailable, including following
situations: the vehicle cannot be started; the air conditioning cannot be used; the door cannot be
opened and closed; the audio-visual entertainment function becomes invalid; all the fault
indicator lights on the instrument panel will illuminate; the active and passive safety functions
become invalid. Once the update is complete, however, all functions will be restored.
 Do not change the vehicle state during installation (do not start the vehicle or shut down the system
by force).
 When updating via WIFI, please keep the network signal in good condition, and do not disconnect
the current network connection during the update process.
 During a host or screen update, a blank screen and system restart are normal. The host will restart
in a few minutes, and the installation results will appear. Do not change the vehicle status during
this time.
 Please check the final result after the update is finished to ensure the vehicle is closed after all
software is installed successfully. If the update failed or there are abnormal conditions during
update progress, please contact the service provider.
 After the upgrade is successful, the various updated system items, function, interface, operating
methods, etc. may change, which is not as described in the manual.
The update information will be included in the interface prompt during upgrade progress.

Voice assistant
Voice assistant can recognize and execute voice commands to control vehicle functions quickly and
improve operation convenience. There are several ways to activate the voice assistant:
 Press the voice button on the steering wheel.
 Voice wake-up: you can perform this function via the system default wake-up words or customized
words.
Check and set wake-up words at [ System Setting ] → [ Customize ] interface. (หน้าที่ 148)

⚠ WARNING
When you control the vehicle using voice assistant, pay attention to the surroundings and personal
safety to avoid pinch, collisions and other severe accidents.

152
Voice Command (when wake-up)
Voice assistant can recognize and execute voice commands to control vehicle functions quickly and
improve operation convenience. Part of voice commands are listed in the following table, not all
voice commands.

Category Function Command

Turn on the AM stations, radio turn to FM 87.5, Turn

Radio
on FM, and so on
Play online radio, following next online radio, and so
Online radio
Media on
Switch on XXX APP, Play Rolling Stones song, Next
Online music
song, and so on
Local music Switch to USB Music, Switch to Bluetooth Music,
(USB/ Bluetooth) and so on
Help me calling 98654072155, Call XXX (Thai
Bluetooth phone Telephone
names in the address list), and so on
General Select 1, YES, exit, next page, and so on
System Adjustment of volume Volume up, Volume down, and so on
Connection controller Turn on bluetooth, Turn off bluetooth, and so on

Take me to XXX, turn on real time traffic report,

Navigation
turn off real time traffic, and so on
Driving Around View Monitor
Open AVM and so on
(AVM)
Head up display Close HUD, increase HUD brightness, and so on

Switch on AC, set fan speed to level 1,

Air conditioning system car fan mode foot, open inner loop, activate
cool mode, and so on

Open Sunroof, open the sunshade curtain, open

Comfort
Vehicle windows, sunroof driver window, close the window on passenger
side and so on

Turn on seat ventilation, set seat ventilation

Seats
level 2, and so on

Weather Weather forecast How is the weather, how is the weather

tomorrow, and so on
… … …

153
 Voice Command (when not wake-up)
Some functions of the vehicle can be controlled by speaking commands without having to wake up
the voice assistant
Category Effective condition Command

Multimedia — Previous music, Next music, Play music,

Play radio, Stop playing, Pause, Previous
music, Next music
System — Turn up volume; turn down volume; open
settings
Air-conditioning — Turning on/off air conditioner

Telephone — Making a call

Turn on navigation — Open the map

Navigate any frames Go home, go to company

Navigating and map is at the Stop navigation

front desk
It can adjust map measuring Map zoom out, map zoom in
Navigation scale
The view image of map can 3D map, 2D vehicle head up, 2D north up
be adjusted
Image of roads recognition Begin navigation, the first road, the second
road, the third road

NOTICE
 Voice skill: navigation, music, video, telephone and other technologies, specific technical ability
and frequently used commands are supported by voice assistant.
 Please activate voice assistant and say “Help” to check these functions.
 Adjustment of voice assistant volume: Adjust the volume via [ System Setting ] → [ Sound ].
(หน้าที่ 147)
 The success rate of speech recognition will be affected by environmental noise, network signal,
usage habits, pronunciation and other factors. The specific use effect is subject to the actual
vehicle environment.
 Using some functions of voice assistance require Internet access.

154
Navigation system
About navigation
 It is recommended not to operate this navigation while driving the vehicle. Please operate under the
premise of ensuring safety after parking to prevent traffic accidents or other dangerous situations.
 The functions and service provided by this navigation is for reference only. Please do not take it
as the only reference of driving or traveling. Please refer to the actual traffic and road conditions,
and strictly abide by traffic laws and traffic rules.
 Using services that require Internet access, such as online navigation, traffic conditions and data
downloads, consumes network traffic.
 Some online functions and services will not be available when the vehicle is not connected to the
Internet and only uses offline navigation.

Enter the navigation interface

The system enters the navigation system by default after power-up. In the other interface touch
pages button to switch to the navigation interface.
Touch the non-button location on the map to call up the hiding function buttons.

A82F7BEF8B35
Ⓐ Map perspective Ⓔ Self-vehicle position
Ⓑ Map zooming Ⓕ Audio playback window
Ⓒ Map measuring scale Ⓖ Navigation setting
Ⓓ Destination searching Ⓗ Navigation mute

155
 Choose destination on map
Touch the location for a long time on the map to switch to the location details interface.

A9175B0F1817

 Tap the back button to return to the previous interface.

 Tap the collection button to collect current place. Touch this button again to stop scanning.
 Tap surrounding search button to search surroundings.
 Tap [ Set as destination ] button to set current place as destination.

Destination searching
Tap the search button in the map interface to switch to the destination search interface.

EF41EFA2B187
 Tap [ Home ] button to set home address. After setting the home address, tap this button to set
the location of home as the destination.
 Tap [ Work ] button to set company address. After setting the company address, tap this button
to set the location of company as the destination.
 Tap [ Favourite ] button to switch to favourite interface and the favourite location. can be
displayed. You can check, delete the favourite position and set it as destination.

156
Route plan
You can switch to route planning interface if you have set the destination through vary methods.

31C5BD107F21
 Tap the more button after route to switch route details. It can display the route name on
current way according to the order from top to bottom.
 Tap search button to switch to destination search interface to add way or change destination.
 Tap service area button to display all service areas on current route.
 Tap [ Recommendation ] button to display the menu of favourite routes and switch favorite routes.
 Tap [Start navigation ] button to switch to interface of route introduction and enter into navigation
mode.

D6CEDB5FFA49
Touch the non-button location on the map to call up the hiding function buttons.

157
 Navigation setting
In the map interface touch settings button to switch setting interface.

494C235443AD
You can set current road conditions, automatically proportional scale, map colour, navigation
broadcast, favorite route, home/company address, delete personal information, online map update,
USB map update and check version details and so on.

158
4 Saftety
Seat belts 161
Airbags 164
Child restraint system 170
Vehicle anti-theft system 174
Emergency cut-off system 175
Event data recorder 176

159
 Seat belts

Vehicle equipment  Do not use organic substances, such as

Please note that this manual contains all the benzene or gasoline, to clean the seat belts,
standard equipment, country-specific equipment and do not bleach or dye them.
and special equipment for this model series.  Children must not play with the seat belt.
Thus, some equipment or features described in If a child accidentally wraps the seat belt
this manual may not be installed onto your around his or her neck while playing with the
vehicle or are only available in some markets. seat belt, he/she may not be able to pull the
For further configuration information, please seat belt, resulting in serious injury or even
refer to relevant sales information or consult death. In this case, if the locking tab of seat
with your distributor selling the vehicle to you. belt cannot be released, use a pair of scissors
to cut the seat belt.
Safety tips  Inside seat belt design is mainly based on
 The shoulder belt must not hang on the neck adult size, so please install proper child
restraint system for children.
area, or pass under the armpit area.
When the seat belt is being used correctly, if
 The lap belt must be secured as firmly as
the belt is in contact with the child's neck or
possible around the lower part of the hip
jaw area or slack to the hip, please switch to
bone.
a child seat instead.
 Each seat belt can only be used by one person.
 If the child is old enough to use inside seat
More than one person (including children)
belt, he (she) shall wear the belt properly.
must not share the same seat belt.
 Precautions for pregnant women
 If more than two people wear the same seat
We strongly suggest that you use the seat
belt, when the vehicle is involved in a collision,
belt. You can also get effective advice by
not only the seat belt can not disperse the
consulting with your doctor. The recommended
impact, but there is a danger of two people
colliding with each other. way of wearing the seat belt for pregnant
women is fundamentally the same as for
 The seat belt shall not be twisted or slack.
other passengers. However, such passengers
 Do not wrap the seat belt around objects
should take note of the following:
with sharp corners, or it may be damaged
during an accident. 1) The lap belt should be positioned as low
 Never use a seat belt that has undergone as possible in the abdomen area, below the
strong impact from an accident or which is bulge of the belly.
otherwise damaged. 2) The shoulder belt should run over the
 Do not remove, disassemble or alter seat belts. passenger's shoulder, over the chest area
 Do not use the seat belt with foreign object but avoid the passenger's abdomen area.
in the buckle. If the seat belt is worn incorrectly, during
 We suggest that when you use the seat belt, emergency braking or collisions, the seat belt
you shall keep your seat belt clean. Oil and may tighten over the abdomen area, causing
water-based materials such as soil, oil stain, injury or even death to the pregnant mother
water, beverage, food residue, shall not be and unborn child.
attached to the seat belt so as to ensure that  We strongly recommend that passengers who
it can be pulled out and retracted smoothly. are ill or disabled use the seat belt. You can
also get effective advice by consulting with
your doctor.

160
 When the seat belt is not in use, the it shall be Operating conditions
fully retracted. Do not twist or jam the seat The pretensioner seat belt works when the
belt, and do not allow the seat belt to touch vehicle receives a significant impact from the
any sharp objects. The seat belt buckle cannot front. It may not work when the following mild
be blocked by foreign objects. Otherwise, impacts occur:
correct engagement of the seat belt locking  When the vehicle hits a concrete wall square
tab and the buckle will be affected. at a speed below 25 km/h.
 When the vehicle collides with an object with
Wear the seat belt properly a small surface area, such as a fixed electrical
 Adjust seat backrest until it is vertical or pole or tree, at a speed lower than 35 km/h.
near-vertical and provides adequate back  The pretensioner seat belt may not fully
support. function when the vehicle is subjected to the
 The seat belt shall be neat. following severe collision.
 The shoulder belt should lie flat on the centre  The vehicle flips over by 90° or 180°.
of the shoulder and not on the neck or elsewhere  When the impact comes from the side or rear
away from the shoulder. of the vehicle.
 The lap belt should be, as much as possible,
fastened around the lower part of the hip bone. ⚠ WARNING
 When using the pretensioner seat belt, please
adjust the seat to the optimal driving position.
⚠ WARNING Otherwise, the pretensioner seat belt may not
 During the drive, all passengers must fasten work properly, which could cause serious
their seat belts in the correct fashion. Failure injury or even death.
to do so can lead to severe injury or even  If you wish to install, remove or dismantle
death from collisions or emergency braking the pretensioner seat belt, be sure to contact
as passengers' bodies are not sufficiently authorised service centre.
bound to seats.  If the pretensioner seat belt is not used correctly,
 At any time, even the driving distance is it will not work as normal. It may cause severe
short, all the passengers and the driver in the injury or even death in an accident.
vehicle should wear seat belts properly.  The pretensioner seat belt cannot be
Otherwise, if an accident occurs, the risk of inflated repeatedly.
injury or death can be increased.  After the pretensioner has been inflated
during the first collision, you should not
extend or retract the seat belt again when
Pretensioner seat belt
the second and subsequent collisions occur.
Both driver’s seat and front passenger’s seat are
Be sure to contact authorised service centre
equipped with pretensioner seat belt.
for replacement.
When a collision occurs, the pretensioner can
 When the pretensioner seat belt is inflated,
retract the seat belt in an instant to secure the
there may be loud sounds and white smoke
passenger to the seat as much as possible. The
emanating from the device. This will not lead
force limiter can maintain seat belt load at an
to a fire or cause harm to the human body.
acceptable level and reduce force exerted on
 When a pretensioner seat belt needs to be
the passenger’s chest.
replaced and disposed of, be sure to contact
authorised service centre

161
 Inadvertent/accidental movements of the
pretensioner seat belt can cause harm to the
human body.

How to use the three-point seat belt

1. Hold the locking tab and pull the seat belt out
of the retractor. Make sure that you do not
twist the seat belt in the process. If you are
unable to pull the seat belt out of the
retractor, you will need to first pull hard at
the seat belt and then release it. Doing so will
trigger the retractor and allow you to pull out
the seat belt smoothly.
2. Insert the lock tongue into the buckle until
you hear a "click" sound.

398F3716FB2E
3. Pull up the shoulder belt until the lap belt sits
securely on the body. Thus, the pelvis is
better secured and the risk of injury during
moments of impact is reduced.
4. Check that the shoulder belt is sitting across
the chest and on the center of the shoulder.
Thus, any impact will be distributed across
the upper skeleton.
5. Press unlock button on the buckle to retract
seat belt. After the buckle has been released,
hold on to the locking tab until the seat belt
has been fully retracted. Take care that the
locking tab does not knock into the passenger
or any nearby objects.

162
Airbag

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and
special equipment for this model series. Thus, some equipment or features described in this manual
may not be installed onto your vehicle or are only available in some markets. For the further
configuration information, please refer to relevant sales information or consult with your distributor
selling the vehicle to you.

Tips for safety

 Airbags cannot be reused.
Once the airbag has been used, it will not work anymore in the second or subsequent collisions,
so be sure to contact authorised service centre for replacement.
 The airbag is an auxiliary device to protect the passenger safety and it shall be used with the seat
belt. In order to obtain the effect of airbag, the passenger must wear the seat belt correctly and
maintain the correct posture.
 Only if the airbag is used properly, can it play its role and effect in full. If used improperly, it may not
play a security role, but may bring harm to passengers.
 When the airbag is being deployed you will notice some loud sounds and smoke.
 This is normal and will not lead to a fire. The smoke released, however, may cause breathing
difficulty when inhaled by individuals suffering from asthma or other respiratory disease. At this
moment, it is safer to flee out of the vehicle immediately. If you are unable to evacuate from the
vehicle, open vehicle doors or windows to let fresh air in.
 When any debris (or gas) released by airbag deployment comes in contact with the eyes or skin,
clean such material off using water as soon as possible. Otherwise, individuals with skin
hypersensitivity may experience a skin reaction.
 Do not touch airbag components after the airbag has been deployed. Because its component parts
will become very hot, it may cause burns and other major injuries.
 Please do not use the airbag for any other purposes.
 Please get in touch with authorised service centre if you need to install radio equipment.
Electromagnetic waves emitted by wireless equipment have a significant impact on the airbag
control units.
 It is forbidden to strike or squeeze the airbag and the position around it.
 Avoid the condition that the airbag cannot work normally during accident or accidental deployment
of the airbag in normal driving, which will cause serious injuries to passengers or even death.

163
Air bag

719409D33256
(A) Front airbag, for:
Driver airbag
Front passenger airbag
(B) Side airbag
(C) Curtain airbags

164
Front airbags  If the object impacted changes shape or moves,
Introduction the force from the collision will be reduced. At
The front airbags are located in the steering this point, the airbag may not deploy.
wheel and the instrument panel which is in front When the vehicle collides into a truck from the
of the front passenger seat, with the airbag logo back, the vehicle will run under the cargo box.
on the steering wheel and instrument panel. As the impact force recognized by the sensor
When the vehicle encounters a strong front is weak, the airbag may not deploy.
impact, the seat belt will be tightened. At the  The airbag may also not deploy depending on
same time, the airbags at the driver’s side and the angle and direction of collision, even when
front passenger’s side will deploy in order to vehicle speed is relatively high.
distribute and cushion any force directed  Please do not allow your body to get too close
towards the head and chest. to the steering wheel or to the lower part of
the instrument panel :
Operating principle 1) When driving a vehicle normally, the
When a head-on collision occurs resulting in driver shall stay away from the steering
moderate or severe impact, the sudden wheel as far as possible while maintaining
deceleration of the vehicle will be noted by a the correct driving position.
sensor. At this time, the control module will 2) The front seats should be as far from the
immediately deploy the airbag. instrument panel as possible.
Precautions 3) All passengers should be belted up in the
 The airbag may deploy when the bottom of correct fashion for optimal protection.
the vehicle encounters the following kinds  Please do not sit on the edge of the seat or
of severe impact : lean on the instrument panel while the
1) When the vehicle runs into the kerb. vehicle is in motion.
2) When the vehicle falls into, or runs over Because the front airbag deploys at a high
a deep pit or drain. speed and with great force. If the passenger
3) When the vehicle climbs over the steps is too close to the airbag at this point, he or
and hits or falls on the road. she may suffer severe injury or even death.
 The airbag may deploy when the vehicle  Please do not allow children to stand in front
rolls over 90° and 180°. However, it will not of the airbag.
be able to function to its full capabilities. When the front airbags deploys, it may cause
 The airbag may not deploy when the vehicle severe injury or even death to child passengers.
encounters the following kinds of severe All children should be seated in the rear seats
impact: and be protected with the correct restraints.
1) When the vehicle hits a concrete wall  Please adhere to the following rules,
square at a speed below 25 km/h. otherwise these items may cause severe injury
2) When the vehicle collides with an to passengers during airbag deployment :
object with a small surface area, such as 1) Please do not place objects on the instrument
a fixed electrical pole or tree, at a speed panel or lean umbrellas, etc. on it.
lower than 35 km/h. 2) Please do not leave objects in the storage
box exposed.

165
 3)
Please do not hang any objects on  Please be sure to consult with authorized
vehicle windows or on the inside service centre for assistance when you need
rearview mirror. to make repairs to the front of the vehicle or
4) Please do not install any decorations on the front cab. Improper repairs can cause
the steering wheel horn cover. distortion to collision signals sent to the
5) Please do not place luggage, pets or airbag sensor, thereby leading to airbag
other objects between the airbag and
malfunctions, which may cause serious
the driver or front passenger.
injuries or even death.
 Please do not clean the inside of the
vehicle with water or cleaning solution.
The gas generator in airbag is a priming Front passenger airbag switch
device. If it becomes damp, its normal
operation will be affected or even cause
serious injuries or death.
 Please do not apply wax, stickers, or similar
items to the airbag cover. Failure to adhere
to the advice can impede airbag deployment.
 Do not damage airbag cover. Otherwise, it
will not work normally. Therefore, be sure
not to open or damage the airbag cover.
 Please do not dismantle, modify, or install
43775C8A92E2
equipment such as airbags, instrument panel
The front passenger side airbag switch is located
and steering wheel. Improper operations can
on the side of the front passenger instrument
cause the airbag to malfunction or deploy
panel.
by mistake, thereby causing severe injury
Use a mechanical key to turn the front passenger
or even death.
airbag switch to OFF position to turn off the
 Do not modify the suspension. If the vehicle
front passenger airbag. At this moment, the
height or suspension stiffness is changed,
front passenger airbag OFF indicator on
the airbag may deploy by accident and
the reading lamp becomes illuminated.
cause injuries or even death.
Use a mechanical key to turn the front passenger
 Please consult with authorised service
airbag switch to ON position to turn on the front
centre for assistance when you need to
passenger front airbag.
install a fender panel and baffle at the front
At this moment, the front passenger airbag ON
of the vehicle. Modifications to the front of
indicator on the reading lamp becomes
the vehicle can cause distortion to collision
illuminated.
signals sent to the airbag sensor, thereby
⚠ WARNING
triggering accidental deployment of the
 Be sure not to place a rear-facing child seat
airbag, which may cause serious injuries or
on the front passenger seat while the front
even death.
passenger airbag is operational. Otherwise,

there will be a serious accident or even
death.

166
 If, under special circumstances, it is 3) Rear collision.
necessary to install a rear-facing child seat 4) Rollover.
on the front passenger seat, please turn off  Do not place any object over side airbags.
the front passenger airbag. Otherwise, Otherwise, it will disturb the normal work of
there will be a serious accident or even the side airbag.
death. In other conditions, you are advised  Never attach any object around the side
not to turn the front passenger airbag lock airbag deployment area. Failure to adhere to
to OFF, as the front passenger airbag would this can cause such objects to dislodge when
not be able to deploy if there was an the side airbags deploy.
accident.  Do not remove, repair or modify seat with side
airbag and parts around the side airbag
deployment area.
Side airbags
Introduction
Warning label
Side airbags are located inside the seat backrest
outside liner, and airbag identification will be
made on the seat backrest. Side airbags are the
supplement of seat belt. In case of side
collision, side airbags will reduce the damages
to inside passenger and prevent subsequent
collisions.

Operating principle
When the vehicle encounters impact from the
0C8DAAED6C78
side, the sensor will detect an acute change in
The identification is located on the central
vehicle speed and then send a signal to the
pillar. It serves to remind you that the vehicle is
control module. If airbag work condition is met,
equipped with side airbags and to pay attention
the side airbag will be deployed instantaneously.
to the relevant issues.
When a side collision occurs, only the side
airbag of the side impacted will deploy. If the
impact occurs on the front passenger’s side of Curtain airbags
the vehicle, even if there is no one in that seat, Introduction
the side airbag on front passenger’s side will The curtain airbags are located on the roof
deploy all the same. lower edge; you can find airbag marks on pillar.
The curtain airbags are a supplement to seat
Precautions belt. In case of side collision, curtain airbags will
 The side airbag may not deploy when the reduce the damages to interior passenger and
vehicle encounters mild impact such as prevent subsequent collisions.
what is described below:
1) Front collision. Operating principle
2) Electronic control unit receives a weak In the event of a side collision, a sensor detects
signal of mild side impact. an sharp change in the lateral acceleration of

167
the vehicle and send a signal to the control
module. If the curtain airbag work conditions
are met, the curtain airbags on the collision
side will instantly inflate.

Precautions
 The curtain airbags may not inflate when
the vehicle encounters mild impact such as
what is described below:
1) Front collision.
2) Electronic control unit receives a weak
signal of mild side impact.
3) Rear collision.
4) Rollover.

 Please do not remain close to the vehicle

doors, door pillars or roof rail, or kneel on a
front seat. Otherwise, passengers’ heads
may suffer a severe impact when the
curtain airbag inflates, which may cause
serious injuries or even death. Pay attention
especially when children are in the vehicle.
 Never attach any object near where the
curtain airbag will inflate. Otherwise, there
is a risk that object may launch into the
cabin when the curtain airbag inflates.
 Do not hang heavy or sharp objects on the
coat hook.
 Please do not use clothes hangers if you
wish to hang your clothing and opt for the
coat hook directly instead. Otherwise, the
clothes hangers may launch into the cabin
when the curtain airbag inflates.
 Do not remove, repair or modify parts near
where the curtain airbag will inflate.
Do not modify roof, roof handrail, roof
handrail bracket and side roof lamp.

168
Child restraint system

Vehicle equipment  If you install the child seat incorrectly, in the

Please note that this manual contains all the event of emergency braking or accident,
standard equipment, country-specific equipment severe injury or even death may occur.
and special equipment for this model series.  Do not place unsecured child seat protection
Thus, some equipment or features described devices in the vehicle.
in this manual may not be installed onto your If you leave it inside the vehicle, it may come
vehicle or are only available in some markets. into contact with passengers or other objects
For further configuration information, please in the event of emergency braking or severe
refer to relevant sales information or consult impact, causing a severe injury or even death.
with your distributor selling the vehicle to you.  Even when the child has sat in a child seat,
take care that his or her head or body is not
Safety instructions for child seat leaning against the vehicle door pillar or roof
Warning label rail. When the curtain airbag fully deploys, it
can be very dangerous in this scenario as the
deployment force may cause severe injury or
even death to the child.
 Depending on the different types of child seat,
when installing or removing a child seat, refer
to the install instructions and precautions
provided with the child seat.
 Be sure to leave enough space around the child
seat and adjust the seat in front if necessary.

90A96F30A2E6
⚠ WARNING
This label, which is located on the front
The following instructions must be followed for
passenger side sun visor, is used to alert you
using a child seat on the front passenger seat.
that your vehicle is equipped with front
 When installing a child seat on the front
airbag. Note the relevant precautions.
passenger seat, the front passenger airbag
must be deactivated.
⚠ WARNING
 The front passenger airbag must be
Do not use rear-facing child restraint systems on
activated as soon as the child seat on the
the seats protected by front airbag (activated),
front passenger seat is removed.
which may cause the child suffering from death
 If necessary, adjust the seat backrest angle
or serious injury.
until there is stable contact between the seat
 If the child seat is not installed with child backrest and the child seat.
seat fixing device, use the seat belt to  Take care that the seat belt is not twisted as
install it and then follow the installation it passes through the guide fitting and does
instructions provided with the child seat. not bend over the edge of the guide fitting
 Properly fasten the child seat inside the
vehicle.

169
 For Group II and Group III child seats, ensure Recommended child seat categories
that the guide device mounted on the child ISOFIX is a mounting system for car child seats
seat headrest are in front of the seat belt based on international standards.
anchorage point. In the user's country, child seats need to meet
the ECE NO.44 specification. Only child seats
Fixing point for child seat that meet the above specification are allowed
Lower fixing point of child seat to be used in vehicles.

Weight group
Weight
Group Age
(kg)
0 Maximum 10 0-9 month(s)
0+ Maximum 13 0-2 year(s)
9 months to
I 9 to 18
4 years
II 15 to 25 4-7 years
928DC87ABB4A III 22 to 36 6-12 years
There are 4 fixing points on the lower part of the Rear-facing child seat, quality group 0/0+
child seat in the clearance between the rear seat Forward-facing child seat, quality group I
backrest and the seat cushion. Cushioned child seat, quality group II/III

Top tether strap fixing point for child seat NOTICE

For optimum protection, use the recommended
child seat type, including rear and lap belt guides.
Not every child is suitable for choosing a child
seat in weight groups, and likewise not every
child seat is suitable for your vehicle. It is
therefore important to check that a child sits
properly in the child seat and that the child seat
is securely fastened in the vehicle.

865BFFDEF410
Installation of child seat
There are 2 fixing points for the child seat top When installing a child seat, you must use a
tether strap on the rear side of rear seat backrest. child seat that is appropriate for the child's age,
weight and physique to restrain an infant or a
⚠ WARNING child in the seat.

Child restraint anchorages are designed to

withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used for adult
seatbelts, harnesses, or for attaching other
items or equipment to the vehicle.

170
Applicability information of child seat Applicability information of vehicle ISOFIX
for different seat positions positions for ISOFIX child seat
Seat position ISOFIX
Front passenger Rear passenger Weight Size Fixed position
Weight Front Front Rear Rear group model module Rear row
group passenger passenger row row external seat
airbag airbag external centre
Portable F ISO/L1 X
ON OFF seat seat
bed G ISO/L2 X
Group 0 X U U X Group 0 E ISO/R1 IL
E ISO/R1 IL
Group Group
X U U X D ISO/R2 IL
0+ 0+
C ISO/R3 IL
Group I X U U X
D ISO/R2 IL
Group II X U U X
C ISO/R3 IL
Group III X U U X
Group I B ISO/F2 IUF
B1 ISO/F2X IUF
Note: the letters filled in the above table are
A ISO/F3 IUF
defined as follows:
U - this seat is suitable for universal child restraint
system certified under this weight group. Note: the letters filled in the above table are
X - this seat is not suitable for use with child defined as follows:
restraint systems in this weight group. IUF - this seat is suitable for general forward-facing
ISOFIX child restraint system approved for the
If you need to install a rear-facing child seat on weight group.
the front passenger seat, please pay attention IL - this seat is suitable for special ISOFIX child
to the following items： restraint system on the list. Such restraint systems
 Please be sure to turn off the front passenger may be special, restricted or semi-general.
airbag switch; otherwise, it will cause serious X - ISOFIX position is not suitable for use with this
danger to children when the airbag deploys. weight group and/or ISOFIX child restraint system
(▷ page 164) of this size.
 When installing a child seat on the front
passenger seat, please adjust the front Child seat installed with the seat belt
passenger seat as far back as possible. 1. Move the front passenger seat as far forward
as possible so that there is no contact
between the front passenger seat and the
child in the rear.
2. Adjust or remove the headrest of the seat
where the child seat is installed; otherwise,
the child seat may interfere with the headrest
and can not be able to fit against the backrest.

171
3. Pull out the shoulder belt, move the belt along ⚠ CAUTION
the indicated route on the child seat and insert If a booster seat is used, do not remove the
the locking tab into the buckle until you hear a
headrest. Also, the top of the headrest should be
"click" sound.
adjusted to a position that is flush with or closest
4. With the body weight pressing down on the child
seat, retract and tighten the shoulder belt to
to the top of the child’s head.
ensure no slack.
5. Shake the child seat gently to make sure that it ⚠ WARNING
has been properly secured.  If the child seat is equipped with a top tether
strap, tighten the top tether strap according
⚠ CAUTION to the installation instructions and precautions
If a booster seat is used, do not remove the provided with the child seat.
headrest. Also, the top of the headrest should Otherwise, severe injury or even death may
be adjusted to a position that is flush with or be caused in the event of emergency
closest to the top of the child’s head. braking or collision.
 Do not lower the headrest after fastening the
Child seats installed with the child child seat top tether strap to its anchor point.
1. Move the front passenger seat as far forward Otherwise, it may come into contact with the
as possible so that there is no contact top tether strap and loosen the strap as a
between the front passenger seat and the result. In the event of emergency braking or
child in the rear. collision, this can cause the child seat to turn,
2. Adjust or remove the headrest of the seat bringing severe injuries or even death.
where the child seat is installed; otherwise,
the child seat may interfere with the
headrest and can not be able to fit against
the backrest.
3. Slide the child seat lock mechanism into the
lower anchor point, and ensure that the two
ISOFIX lock mechanisms are securely fixed.
4. When fixing the top tether strap, refer to the
instruction manual of the child seat.
5. Shake the child seat gently to make sure that
it has been properly secured.

172
Vehicle anti-theft system

Vehicle equipment Alarm trigger condition

Please note that this manual contains all the In an arm mode, the following actions may trigger
standard equipment, country-specific equipment an alarm:
and special equipment for this model series.  Use the mechanical key to open the vehicle
Thus, some equipment or features described in doors.
this manual may not be installed onto your  When a side door or the back door is forced
vehicle or are only available in some markets. open.
For further configuration information, please
refer to relevant sales information or consult Alarm cancellation
with your distributor selling the vehicle to you. After triggering the anti-theft alarm of the
vehicle, the alarm can be cancelled by the
System introduction following operations:
The vehicle anti-theft system helps to keep  Switch power supply mode to ON mode.
your vehicle and valuables from being stolen.  Start the vehicle successfully.
The vehicle anti-theft system will emit audible  When the power supply is in OFF mode,
and visual alarm if someone tries to enter the unlock the doors or the tailgate via the
vehicle by force. button on the key or the PEPS.

⚠ WARNING System off

Do not attempt to modify the vehicle anti- The vehicle doors and back door are unlocked
theft system. via the key button or the PEPS.
The turn signal lamp flashes twice and the anti-
System activate theft function of the vehicle is off.
1. After the door is successfully locked by the
button on the key, PEPS or the mechanical
key, the turn signal lamp flashes once, and
the vehicle enters the pre-arm mode. In pre-
arm mode, you can still operate the vehicle
without triggering the anti-theft alarm.
2. Once pre-arm mode has been activated for
about 15 seconds, the vehicle will then be
armed automatically and the anti-theft
function is activated.

⚠ CAUTION
Please check whether all the vehicle doors and
back door are completely closed. Otherwise, the
vehicle anti-theft system cannot be activated.

NOTICE
The center control button will fail in the anti-
theft state of the vehicle.

173
Emergency cut-off system

Vehicle equipment
Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Emergency cut-off system

When the impact sensor detects a certain
degree of impact, the system will cut off the
high voltage current and fuel supply, and
minimize the danger caused by electric shock
and fuel leakage.
If the emergency cut-off system is activated,
the vehicle cannot be restarted.
At this time, please contact authorized service
centre.

174
Event data recorder

Vehicle equipment The data items recorded by EDR and their uses
Please note that this manual contains all the are as follows:
standard equipment, country-specific equipment Data item Applications
and special equipment for this model series. Braking state Record the brake pedal
Thus, some equipment or features described in status during collision
this manual may not be installed onto your Speed during Record the speed at the
vehicle or are only available in some markets. collision time of collision
For further configuration information, please Status of the seat Record the safety belt
refer to relevant sales information or consult belt lock body status during collision
with your distributor selling the vehicle to you. Status of the airbag Record whether the
System warning airbag failure warning
System introduction lamp lamp is on before
The vehicle is equipped with the event data collision
recorder (EDR).
The event data recorder (EDR) is mainly used
Data disclosure
to record data related to vehicle dynamic
Any data recorded by EDR will not be disclosed
system and safety system when a vehicle
to third parties except in the following
collision happens in order to help understand
circumstances:
the operation conditions of vehicle system.
 With the consent of the vehicle owner or lessee.
However, since collision severity and type
 To be used in a lawsuit at the official request
vary, EDR may not record the data.
of the police, court, or government department.
However, if necessary, the data recorded by
NOTICE the EDR will be used to:
EDR records data only when a vehicle meets a  Research and develop the vehicle safety
major collision. When the vehicle runs normally, performance.
EDR does not record data.  For R&D purpose, data is disclosed to the
third parties without disclosing specific
Data reading information about the owners and their
Except the vehicle manufacturer, other parties vehicles.
(such as law enforcement agencies) can read
the data recorded in EDR after connecting the
laptop with the onboard diagnostic interface
to enter the EDR by using CANoe equipment.
The data reading equipment can be purchased
from CANoe software vendors.
The data items recorded by EDR and their uses
are as follows:

175
176
5 Emergency
On-board toolkit 179
Emergency tyre repair and inflation 180
In case of an accident 182
Jump start 183
Engine overheating 185
Towing 186
Service and rescue 190

177
On-board toolkit

Vehicle equipment
Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Location of on-board toolkit

On-board document packages are placed in the
storage box on the side of the front passenger,
and other on-board tools are placed in the luggage
area.

⚠ CAUTION
 The driver must be familiar with the storage
location and instructions of the on-board
toolkit in order to cope with emergency.
 And the driver must return the onboard
toolkit to their designated positions after
use, and fix them securely. Random placement
may cause accidents.

178
Emergency tyre repair and inflation
 The tyre repair fluid has limited ability to seal
Vehicle equipment the puncture of the tyre wall. If the tyre has
Please note that this manual contains all the large fissures, cracks or similar damage, tyre
standard equipment, country-specific equipment repair fluid shall not be used to seal the tyre.
and special equipment for this model series.  The tyre repair fluid tank must be replaced
Thus, some equipment or features described in after use. It is recommended that it be replaced
this manual may not be installed onto your by professionals from authorised service centre.
vehicle or are only available in some markets.
For further configuration information, please ⚠ WARNING
refer to relevant sales information or consult  If the tyre repair fluid has expired, please
with your distributor selling the vehicle to you. replace it and treat it as hazardous waste.
 Eating the tyre repair fluid by mistake is
Inflater and tyre repair fluid harmful to health. It may cause allergic
reaction even in the case of skin contact. In
case of contact with skin, immediately wash
the sealing liquid from skin with water or
soapy water.
 The tyre repair fluid must be stored out of
reach of children.

Emergency tyre repair

1. If the tyre is repaired in a place where vehicles
E61433C7A117 pass, please put a warning triangle at an
(A) Outlet tube appropriate position and turn on the hazard
(B) Air inlet warning lamp.
(C) Inflation tube If the tyre puncture is caused by nails or
(D) inflater switch similar objects, leave the objects in the tyre.
(E) Barometer This helps to seal the puncture hole.
(F) Power cable 2. Shake the tyre repair liquid and use it evenly.
(G) Tyre repair liquid Make sure that the inflater switch is off (in
position "0"), and then take out the power cord
In case of tyre leak caused by puncture of and inflation tube.
foreign matters, emergency maintenance can 3. Unscrew the cover of the tyre repair fluid inlet,
be carried out with inflater and tyre repair connect the inflation tube to the tyre repair
fluid. fluid inlet and tighten it, and connect the
outlet tube of the tyre repair fluid to the tyre
NOTICE valve.
 The inflater and tyre repair fluid are only
suitable for sealed tyres with puncture on ⚠ CAUTION
the tread. The inflation tube cannot be bent.

4. Plug the inflater power cord into the standby

power outlet and start the vehicle.

179
5. Switch the inflater switch to the position "I" ⚠ CAUTION
to start the inflater and inflate the tyre to After the tyre is inflated, it is necessary to
240~250 kPa. install the dust cover of the tyre valve to
prevent the gravel and dust from damaging the
⚠ WARNING tyre valve.
Do not stand beside the tyre when operating the
inflater. If the tyre is cracked or uneven, the ⚠WARNING
inflater must be turned off immediately. After the tyre is repaired with inflater and
tyre repair fluid, the driving speed shall not
⚠ CAUTION exceed 80 km/h and the driving distance
 When the inflater is turned on, the air shall not be more than 200 km. It is
pressure will be very high at first, then recommended that you repair or replace the
decrease slowly, and gradually increase with damaged tyre as soon as possible, and
the inflation air pressure. inform the maintenance technician that the
 The inflater shall not run for more than 10 minutes; tyre contains tyre repair fluid.
otherwise, there is a risk of overheating.
 If the tyre pressure is still lower than 170 kPa
Tyre inflation
after inflation, it means that the tyre has a
When the tyre pressure is too low, you can use
large hole, so please do not continue to inflate
an inflater to inflate the tyre.
it. At this time, you are suggested to contact
1. Make sure the inflater is turned off, and take
authorized service centre.
out the power cord and inflation tube.
2. Screw the inflation tube into the tyre valve.
6. Turn off the inflater, remove the power cord
3. Plug the power cord into the standby power
from the 12V outlet, and remove the tyre repair
outlet and start the vehicle.
fluid from the tyre valve.
4. Turn the inflater switch to position "I" to start
7. Drive immediately (within 1 minute) at a speed
the inflater.
of 20~60 km/h for about 5 km, so that the tyre
repair fluid can seal the tyre evenly.
⚠ CAUTION
8. Connect the inflater and read the tyre pressure
The inflater shall not run for more than 10 minutes;
on the pressure gauge.
otherwise, there is a risk of overheating.
 If the tyre pressure is lower than 170 kPa, it
means that the tyre is not completely sealed.
5. Inflate the tyre to the pressure specified in
At this time, do not continue driving and
the tyre pressure label.
contact authorised service centre.
6. Turn off the inflater, disconnect the inflation
 If the tyre pressure exceeds 170 kPa, the tyre
tube and the power cord, and install the dust
shall be inflated to the pressure specified in the
cover of the tyre valve.
tyre pressure label.
9. Turn off the inflater, disconnect the inflation
tube and the power cord, and install the dust
cover of the tyre valve.

180
In case of an accident

Vehicle equipment
Please note that this manual contains all the
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Traffic accidents occur to vehicles

When the vehicle is forced to stop on road
because of traffic accidents or vehicle failure, in
order to warn other vehicles, please take the
following measures:
 Turn on the emergency flashers.
 Please place the warning triangle behind
your vehicle in accordance with local traffic
laws and regulations.

181
 Jump start

Vehicle equipment 2. Open the protective cover on the positive

Please note that this manual contains all the terminal of the battery.
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Symptoms of a drained vehicle 98FE020C1F0A

battery 3. Connect the booster cables in the following
 The vehicle cannot be started. order.
 Headlamps are darker than normal.
 The horn cannot give a sound or the sound
is weak.

How to jump start the vehicle

If you are unable to start the vehicle with
depleted battery, you can jump to the battery of
using another vehicle to start the vehicle.

⚠ CAUTION 242DEA84CEC9
 Not all the vehicle's batteries can be used (A) Positive terminal on drained battery
for this. Jump start can only be performed (B) Positive terminal of battery on rescue vehicle
with a battery having a rated voltage of 12 V. (C) Negative terminal of battery on rescue vehicle
 You cannot start the vehicle by using a (A) Negative terminal on drained battery
trolley or trailer.
4. Recharge the battery.
1. After removing the luggage area cover plate, Start the recovery vehicle, increase the
open the battery plate. engine speed slightly, and keep such speed
for about 5 minutes to temporarily charge
the depleted battery of the vehicle.
5. Start the vehicle with depleted battery.
If still unable to start the vehicle, check that
the jumper cables have been connected
correctly, and then allow the battery to
recharge a little more.
6. Remove the jumper cable.
Once the vehicle is started, remove the jumper
cable in an order contrary to the connection.
5D0F49A67D5E

182
⚠ WARNING
 During charging or jump starting, gas may
escape from the battery. There is a risk of
explosion at this time. Keep the battery
away from sparks, open flames and other
flammable materials.
 Battery fluid is corrosive, and it can cause
serious injury to eyes and skin. In case of
accidental contact, please rinse immediately
with plenty of water and seek medical
attention immediately.
 When connecting or removing jumper
cables, you cannot wind the cables with
fans, belts and the like.
 Ensure that all cables are connected correctly,
and keep a certain distance between their
ends to avoid contact between positive and
negative poles.

⚠ CAUTION
If a battery is often lack of electricity, please get
to authorised service centre for inspections.

183
 Engine overheating

Vehicle equipment 4. Check the coolant level. Please top up the

Please note that this manual contains all the coolant if the coolant level is too low. And
standard equipment, country-specific equipment check for pipeline leakage; if there is any
and special equipment for this model series. leakage, please contact authorised service
Thus, some equipment or features described in centre.
this manual may not be installed onto your 5. Check whether there is any foreign object in
vehicle or are only available in some markets. the core of the radiator. If there is any foreign
For further configuration information, please object, remove it.
refer to relevant sales information or consult
with your distributor selling the vehicle to you. ⚠WARNING
 Do not open the engine hood immediately
When the engine is overheated if you see steam emanating from the engine
NOTICE hood. Doing so may cause erious injury
Under extreme conditions (such as dragging, such as burns.
towing, climbing, overload, etc.), the engine  When the radiator is at a higher
may overheat and the power of the whole temperature, do not open the radiator cap
vehicle will decrease. or the overflow tank lid. Otherwise, exiting
steam or coolant may cause severe injuries
Overheating symptoms such as burns.
 The water temperature is in the red zone.  When opening the radiator cap or the
 Engine accelerates weakly. overflow tank lid, do not touch or get close
 There is steam emanating from the hood. to the fan and belt. Also, open the cap
 A/C compressor may stop working slowly after covering it with a piece of cloth.
automatically.  When the engine is running, do not touch or
get close to the fan and strap. Otherwise,
Handling methods there is a risk of your hands or clothing
1. Park the vehicle in a safe place and shut becoming caught within and of severe
down the engine. injury as a result.
If the A/C system has been turned on at  Do not refill coolant in an overheated engine.
this point, please turn it off. If a coolant is suddenly added, it is easy to
2. Check if steam is emanating from the hood. damage the engine. Add a coolant after the
 If no steam is emanated, open the engine is completely cooled.
engine hood and then start the engine.
 If steam is emanating, wait until there is
no more steam. Open up the hood, and ⚠ CAUTION
then run the engine. If the water temperature indicator comes to the
3. Check if the cooling fan is running. red warning range again, head to your nearest
 If the fan is not working, shut down the authorised service centre for inspection as soon
engine and contact authorized service as possible.
centre.
 If the fan is running normally, wait for
the water temperature to begin to drop,
then turn off the engine.

184
Towing

Vehicle equipment Towing with the lift truck

Please note that this manual contains all the Towing from the front
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Use a professional vehicle to tow

6BB6EC6FBF2F
⚠WARNING
The rear wheels and axles of the vehicle must be
Traction must comply with local regulations
in good condition. The parking brake must be
regarding trailer towing.
released and the vehicle must be locked securely.
Towing from the rear
⚠ CAUTION
In the case of automatic car washing and
towing, the parking brake needs to be released.
You can directly start the wash/ trailer mode
through the multimedia display. (▷ page 87)

When the vehicle needs to be towed, we

suggest an elevating truck or flat truck, and
you shall entrust a authorised service centre or
a specialized towing company with the traction.
FFEE0CD03B9B
Towing with the flatbed truck Place the tow truck under the front wheel and lock
firmly.
Towing with the hoisting type truck is prohibited

04FD77FA04F8
When using a flatbed truck, you must lock the
vehicle firmly.
9104EBEC04BC
It is forbidden to use a hoisting type truck for towing,
otherwise it may damage the vehicle body.

185
Towing with the tow hook Rear tow hook
1. In the gap at the tow hook cover, pry down the
Tow hook
cover using a flathead screwdriver wrapped
Front tow hook
by the cloth.
1. In the gap at the tow hook cover, pry down the
cover using a flathead screwdriver wrapped
Type I
by the cloth.

Type I

C26365676BAF
Type II

36A59E9ED216
Type II

67B9E0D470B2

2. Screw the tow hook clockwise into the hole

85C6328CE0DC
and tighten it to ensure that it is securely
2. Screw the tow hook clockwise into the hole
installed.
and tighten it to ensure that it is securely
installed.

BE4F815B6C12

097E12BE67EA

186
Tow rope If the vehicle will not start, switch the power
The tow rope shall be elastic to protect supply mode to ON and shift the gear to the
vehicles. It is recommended to use artificial N position.
fiber rope or the rope made of similar elastic
materials. Tow ropes can only be installed on ⚠ CAUTION
the designated trailer hook or towing ring of When you cannot switch the transmission to the
the vehicle. N gear position, do not use tow hooks for towing.
When installing tow ropes, you shall be careful
2. Turn on the hazard warning light, release the
not to damage the vehicle body. The distance
parking brake and wait for towing.
between towing vehicle and towed vehicle
The towing speed is not greater than 12 km/h
shall be more than 4 m and less than 10 m.
and the towing distance is not greater than 25
A recovery blanket shall be attached to the
km.
center of the tow rope. For towing at night, tow
ropes with reflective materials shall be used as
⚠ CAUTION
much as possible to increase the warning effect.
 If the vehicle is not started, the assist system
will not work, and the steering and braking
⚠ CAUTION
operations will be difficult.
 Tow rope must be purchased by yourself.
The vehicle speed should be reduced as much
 Do not use a steel rope to tow as that will
as possible during towing.
damage the bumper.
 During towing, pay attention to the brake
lights of the vehicle in front to avoid
Vehicle failure occurring looseness of the tow rope.
When the vehicle fails, if the towing cannot be  When the vehicle moves on a long downhill
performed by special vehicles, a tow hook can road, ropes should not be used to tow the vehicle.
be used to tow the vehicle temporarily. This  Do not tow the vehicle backwards.
towing method can only be used to tow a
vehicle on hard pavement in a short distance
Towing other faulty vehicles
at a low speed.
1. When towing, turn on the hazard warning
lights and follow relevant local laws and
⚠WARNING regulations.
Towing must comply with local regulations 2. Start slowly until the tow rope tightens, then
regarding trailer towing. accelerate carefully.

Towing the vehicle ⚠ CAUTION

For towing the vehicle, the driver must sit in  Do not tow a vehicle heavier than the towing
the vehicle and operate the steering wheel and vehicle; otherwise, the vehicle can be easily
brake pedal, with the wheels, axles, steering damaged.
system, brake system, transmission system  Avoid sudden start or unstable driving
(transmission, etc.) and lighting system (turn operation; otherwise, the tow hook or tow rope
signal light and brake light) in good condition. will be subjected to excessive tension.
The detailed methods are as follows:  When the vehicle moves on a long downhill
1. Start the vehicle and shift to the N gear road, ropes should not be used to tow the vehicle.
position.  Do not tow the vehicle backwards.

187
When the vehicle gets stuck or bottoms ⚠ WARNING
out, Please observe the following precautions during
When driving in snow, mud and sand, the rescue. Otherwise, it will easily cause vehicle
vehicle is easy to get stuck or bottom out. damage and even endanger personal safety.
Therefore, you shall drive carefully. 1. When trailer hook is used to tow the vehicle,
If the vehicle gets stuck, you can try the a recovery blanket must be tied in the middle
following operations: of the tow rope to prevent the trailer hook or
1. Shut down the engine and apply parking brake. rope from breaking and rebounding, which
2. Remove the mud, snow or sand around the may cause vehicle damage and even endanger
stuck tires. personal safety.
3. Place wood blocks, stones or other materials 2. It is forbidden to drag the vehicle from the
to help improve the tire adhesion. side or vertically, with the best angle of trailer
4. Start the vehicle again. hook within the range of 5° up and down and
5. Release the parking brake and accelerate 25° left and right.
carefully to get the vehicle out of the pit. 3. It is forbidden to drag the vehicle during race
start. The initial towing speed shall not
⚠WARNING exceed 5 km/h (start slowly until the tow rope
While freeing the vehicle, you should pay is taut).
attention to the following: 4. When the vehicle is to be dragged with a
 Make sure that the surrounding area is trailer hook, the drag/towing force shall not
clear and free from any other vehicles, exceed the weight of the vehicle.
objects, or persons.
 The moment the vehicle gets out from the pit,
it will suddenly rush forward or backward, so
be careful.

When the vehicle gets stuck or bottoms out,

please contact professional rescue teams or
service provider if the vehicle cannot get out
of the trap in the methods above. Dragging
unprofessionally for rescue is prohibited.

188
Service and rescue

Vehicle equipment Manual services

Please note that this manual contains all the Press and hold the manual service button
standard equipment, country-specific equipment to trigger a manual service call. Through manual
and special equipment for this model series. services, you can search for destinations and
Thus, some equipment or features described in points of interest, inquire about information,
this manual may not be installed onto your book services, consult on car networking
vehicle or are only available in some markets. problems, request road rescue, etc.
For further configuration information, please During the manual service call, press and hold
refer to relevant sales information or consult the manual service button to end the call.
with your distributor selling the vehicle to you.

Emergency rescue
On-board telephone
Press and hold the emergency rescue button
The button and indicator of the onboard
to trigger an emergency rescue call. During the
telephone is on the panel of the reading lamp.
emergency rescue call, press and hold this
button again to end the call.
In the event of a collision (when the airbag is
deployed), an emergency rescue call will be
triggered automatically, and the call cannot be
manually ended.
After an emergency rescue call is triggered, the
rescue center will immediately accept the
rescue request from the vehicle.

A61A62B80584 NOTICE
Ⓐ The handle service Do not randomly and frequently trigger the
Ⓑ Emergency rescue button emergency rescue calls.
Ⓒ Gateway indicator
Press the cover to open it, then you can operate ⚠ CAUTION
the emergency rescue button. The function of emergency rescue call is affected
by various factors. Thus, the emergency rescue
⚠ WARNING call may be unavailable in case of any of the
When the emergency rescue button does not following cases (including but not limited to):
need to be operated, please close its cover.  If the vehicle networking system fails or is
damaged, it will be impossible to trigger an
NOTICE emergency rescue call.
 The communication device conforms to the  If the audio equipment is damaged, or the
standard and requirements of NBTC harness connected to the vehicle networking
 The electromagnetism field intensity of system and the audio equipment is
communication device is consistent with damaged or connected falsely, it will be
The Safety Standard for Human Body to impossible to make normal rescue calls with
Use Radiocommunication Equipment, the customer service.
published by National Telecommunications
Commission (NTC)

189
 If the airbag fails to deploy in a minor collision Status of
or abnormality, it will be impossible to Indicator Description
automatically trigger the rescue call. In this light
case, you can trigger the emergency rescue Disconnect the battery and
call manually or make the call by other means. Orange lamp re-connect it, indicating
 If the emergency rescue button is damaged, normally on that the car networking
the emergency rescue call cannot be system is starting.
triggered manually. During the starting of the
Orange lamp
 If the mobile network signal (cell phone car networking system, it is in
flashing
signal) is weak, interfered, or blocked, etc., it a call state.
will be impossible to trigger an emergency The car networking system
Green Lamp
rescue call. works normally and has
normally on
 In areas (such as underground parking lots, normal network connection.
tunnels, and mountain areas) where the GPS Green The car networking system
equipment is damaged or the signal is week, light flash is in a call state.
it may be impossible to locate the vehicle. The car networking system
 After the vehicle is powered off, it may be Red lamp fails to pass the self-
impossible to trigger an emergency rescue call. Normally on inspection and is in an error
 The emergency rescue services may not be state.
available due to riots, fires, floods, storms,
explosions, wars, government actions, orders
⚠ WARNING
given by judicial administrative organs,
It is forbidden to modify the car networking system.
social environment and other force majeure
factors.
NOTICE
 The emergency rescue services may not be
Please observe the following suggestions during
available if other software you have
daily use:
downloaded and installed or other websites
 Regularly check whether the car networking
you have visited contain viruses,
system is running normally.
 Trojans or other malicious programs and
The indicator of the car networking system
threaten the security of your equipment and
is green, indicating that the system is
data.
normal. If there is a fault, please go to the
 Situations where other objective factors
service station for inspection and
render the emergency rescue call unusable.
maintenance in time.
 It is recommended to replace the builtin battery
Car networking function indicator
of the car networking equipment once every
Status of
3 years at most.
Indicator Description
Please go to the service station to replace
light
the battery in time.
The car networking system has
no network connection (for
OFF example, the SIM card used is
not registered or cannot be
connected to the network).

190
6 Maintenance
Necessity of vehicle maintenance 190
Engine compartment 191
Engine compartment 197
Vehicle maintenance 201
Regular maintenance table 207

191
Necessity of vehicle maintenance

Vehicle maintenance, a health diagnosis of the vehicle, can reduce the trouble of
repairing the vehicle.
When the vehicle is in use, its components and parts will inevitably wear out. To ensure safe driving
conditions, regular inspections, maintenance, and repairs are required to maintain and restore
vehicle performance.

Vehicle maintenance making you drive more safely

During the maintenance, you can carry out necessary preventive maintenance according to the use
of the components and parts, so that you can safely drive the vehicle before the next maintenance.

Extending the service life of the vehicle and reducing the use cost of the vehicle
Components and parts such as brake linings and tyres, etc. cannot be used permanently, as they will
gradually wear out while in use. Use of components and parts that exceed the wear limit is likely to
cause vehicle breakdown and even lead to traffic accidents. Therefore, it is necessary to conduct
regular maintenance.

192
Engine compartment

Vehicle equipment
Please note that this manual contains all the standard equipment, country-specific equipment and special
equipment for this model series. Thus, some equipment or features described in this manual may not
be installed onto your vehicle or are only available in some markets. For further configuration
information, please refer to relevant sales information or consult with your distributor selling the
vehicle to you

Tips for safety

⚠ WARNING
 The engine compartment is a hazardous area of operation and must be handled with extreme
caution!
 When performing fluid inspection and filling operations, observe the following requirements,
otherwise burns or fire may occur:
Switch the power mode to OFF mode.
Apply parking brake.
Let the motor and drive motor cool completely.
Keep children away from the engine compartment.
Do not splash fluid on a hot engine.
Do not allow water to come into contact with the engine compartment.
 When performing operations related to fuel system or electrical devices, observe the following
precautions, otherwise fire may occur:
Disconnect the negative terminal of the battery.
Do not smoke.
Do not operate near open flames.

⚠ CAUTION
When adding fluid, be careful not to misuse it. Otherwise, it may cause serious functional defects or
damage to vehicle components.

193
Fluid level

B4AEB0959B99
(A) Engine coolant overflow tank (D) Engine oil filler cap
(B) Windshield washer fluid reservoir (E) Engine oil dipstick
(C) Brake fluid reservoir (F) Overflow tank of drive motor coolant

194
Engine oil  Care should be taken to prevent burns when
Check checking or filling engine oil. Keep the
engine oil in a safe place when it is not in
use. If the engine oil leaks into the ground or
floats on the water surface, environment will
be polluted.

Filling
Open the engine oil filler cap, and slow pour the
oil so as to avoid oil spill. Any oil overflow must
be removed immediately. Otherwise, the spilled
oil may cause damage to the compartment
8F3D41CDBC64 components.
(A) Minimum Engine oil plays an important role in ensuring
(B) Maximum engine performance and longevity. Therefore, it
Stop the vehicle on flat ground and warm up is important to use high quality, purified oil.
the engine to normal water temperature. Then, Please use only engine
switch the power mode to OFF mode, and pull oil that meets specifications so as to ensure the
out the engine oil dipstick and clean it out after vehicle performance.
10 minutes. After that, fully insert the oil
dipstick to the oil dipstick conduit; finally pull
Oil additives
out the oil dipstick and check the oil level after
Your vehicle does not require any oil additives,
10 s.
as additives cannot improve the performance
The oil level should be between the maximum
and durability of the engine but product
and minimum levels marked on the oil dipstick.
chemical reacts with engine oil causing oil
If the engine oil level is close to or lower than
invalid and damaging engine.
the minimum level marked, top up engine oil
until it is at the level between the maximum ⚠ CAUTION
and minimum levels marked.  Therefore, check and replace engine oil on a
regular basis. Otherwise, insufficient oil
NOTICE levels or deteriorated engine oil may cause
The actual size and shape of the oil dipstick poor lubrication of engine rotation parts,
vary from engine model. thereby cause sintering and hence damage
to the engine.
⚠ WARNING  The engine oil works to lubricate and cool. Oil

 When the engine is running, if you close levels go down over time even if you are

contact with rotating parts such as the driving normally, as a certain amount of
engine oil in the lubricant piston and valve
strap or fan, your hands, clothing, tools and
so on, may be trapped into the rotating also ends up being spent in combustion
chamber. Engine oil levels may go down
parts, resulting in severe consequences.
 Care should be taken to prevent burns depending on your specific drive conditions.
 Take care not to exceed marked maximum
when checking or filling engine oil.
levels when topping up engine oil.

195
Brake fluid Filling
Check When the engine and drive motor cools, slowly
The fluid level in the tank should be checked open the lid to let the pressure out.
regularly. If the coolant spills, clean it up immediately to
Check that the fluid level in the tank is between prevent parts or paint from being damaged.
the minimum and maximum marked levels. Be sure to use the specified type of coolant.
If the brake fluid level is lower than the
minimum level marked, top up with new brake ⚠ CAUTION
fluid until the level is between the maximum  The coolant contains ethylene glycol to
and minimum levels marked. lower its freezing point. Indiscriminate
Also make sure that the braking system shows disposal may lead to water pollution.
no signs of leakage.  Do not open the overflow tank cover when
the engine compartment is at a high
Filling temperature. There may still be some
Pry open the tank cover. Pour in the fluid slowly pressure inside the cooling system.
to prevent overflow. Any oil overflow must be Opening it at this point may cause burns or
removed immediately. other injuries when heated coolant spurts out.
Otherwise, the spilled oil may cause damage to  When replacing the engine coolant or when
the compartment components. the drive motor battery is very short of
Please only use brake fluid that meets specifications. coolant, contact authorized service centre.

⚠ WARNING Windscreen washer fluid

 Insufficient brake fluid levels can compromise Filling
brake performance and increase the risk of an Open the tank cover. Pour in washer fluid
accident. slowly to prevent overflow. Any washer fluid
 Brake fluid is harmful to the human body and overflow must be removed immediately.
corrosive. In case of accidental contact, rinse You should use quality washer fluid for better
immediately with plenty of water. If you ingest cleaning capabilities and for antifreeze protection
it, go to a hospital immediately. in cold season.

NOTICE
Engine/drive motor coolant
You should use the detergent with enough
Checks
anti-freeze performance, if the ambient
The water level in the overflow tank should be
temperature is lower than 0 ℃.
checked regularly.
The detergent should be placed out of the
Check that the fluid level in the overflow tank is
reach of children to avoid accidental ingestion.
between the minimum and maximum marked levels.
The detergent is flammable and should be
If the coolant level is lower than the minimum
stored far from fire.
level marked, top up with new coolant until the
coolant level is between the maximum and ⚠ CAUTION
minimum levels marked. Also make sure that Please do not top up liquids such as soapy
the cooling system shows no signs of leakage. water into the tank in place of the detergent.
Otherwise, the paint on vehicle body may be
damaged.

196
⚠ WARNING  The cooling fan may be started at any time.
Do not top up washing fluid when the engine is Do not put your hand into the fan shield.
at a high temperature, or when the engine is Otherwise, when the fan is started unexpectedly,
running. serious personal injury may be caused.
This is because the washing fluid contains
alcohol. Spilling the fluid on the engine carries a Engine coolant warning label
risk of fire.

Radiator and fan

Regularly check the radiator, fan and other
heat-radiating components in the engine
compartment. If a component is particularly
dirty or has foreign objects, please clean it in
time. When you cannot determine whether it is
working normally, please send your vehicle to a
authorized service centre for checking.
7292828C8D61
Please timely check whether the radiator, fan
and other heat-radiating components are The identifier is located on the overflow tank of
covered with dirt when the vehicle is driving in
the engine coolant. It serves to remind you to
a bad environment (such as driving through
refrain from opening the
water, sand and mud) each time. If they are overflow tank cover when the engine and the
covered by dirt, please go to a authorised
radiator are overheated. Otherwise, the hot
service centre for inspection and cleaning timely. liquid and steam be forced out under system
pressure, causing burns.
Safety labels and identifiers
Engine compartment warning label Warning label of drive motor coolant

6FC9C3B803CD 265F2549F1C8
This label is located on the engine compartment The label is located on the overflow tank of the
front cover plate or the front grille trim plate to drive motor coolant. It serves to remind you to
prompt you: refrain from opening the overflow tank cover
 The type and filling amount of air when the drive motor is overheated. Otherwise,
conditioning refrigerant. the hot liquid and steam may be forced out
under system pressure, causing burns.

197
Battery warning label
Type I

340CF5EC9B21
Type II

A86516835B47
This label is located on the battery to inform
you of the following precautions before
installing, removing, or inspecting the battery:
 Children should be kept away from the
battery.
 The battery may produce flammable gases
in the use or charging process, so it should
be away from high-temperature heat source
and open flame.
Otherwise a fire or explosion is likely to occur.
 The battery contains corrosive liquid.
 Take necessary protective measures such as
wearing goggles during operation.

198
Parts replacement

Vehicle equipment > Located in the instrument panel near the

Please note that this manual contains all the steering wheel
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Fuse 3C95CEB1BB63
If any electrical components do not work, the Remove the cover and you can see it.
fuse may have been blown out. In this case, carry
out the inspections based on the following > under the luggage area cover plate
operations and replace the fuses if necessary:
1. Turn off all electrical components.
2. Switch the power supply to OFF mode, apply
the parking brake, and disconnect the
negative terminal of the battery.
3. The fuses are located in the following positions:

> Located in the fuse box of the engine

compartment

A90DD219A480
Take out the luggage area cover plate, on-
board toolkit and tray on the left in sequence.
Press and hold the pawls at the fuse box cover
as shown, and then remove the fuse box cover
and you can see the fuse.

⚠ CAUTION
 Never let water or other liquids get into the
0E039B6DC904 fuse box. Otherwise, the electrical components
Press and hold the two pawls on the fuse box will be damaged.
cover, and then pull up the fuse box cover to  Install the fuse box cover on the fuse box
open the fuse box. correctly. Otherwise, penetration of moisture
or dirt will affect the use of fuses .

199
4. Use the fuse clips in the vehicle to pull out (A) Normal fuse
the fuses. Locate the fuse of the faulty (B) Blown fuse
electrical appliance according to the fuse
label and check it ⚠ WARNING
For blowout fuses, do not try to repair or
replace them with fuses with inconsistent
colours or amperages; otherwise, a fire will
occur due to cable overload.

6. Check whether the electrical components

return to normal operation.

⚠ CAUTION
If a spare fuse with the same amperage is blown
45B3BB806093
out again in a short time or the electrical
⚠ CAUTION
components do not return to normal operation,
 The fuse clip and the spare fuse are located in
the vehicle may have a serious electrical
the cover of the engine compartment fuse box.
system failure. In thiscase, contact a authorised
 The engine compartment fuse box cover
service centre for assistance timely.
and the instrument panel fuse box cover
plate are attached with fuse labels. With
Wiper blade
these labels, the relationship between fuses
Front wiper blades replacement
and electrical components can be determined.
Regularly check the wiper blade, and replace it
 Since there may be more than one fuse
immediately if you find the following conditions:
causing the failure, check all the fuses that
 Cracks or hardened areas are found on
may cause the failure before the failure
wiper blades.
disappears. If the failure cannot be eliminated
 Streaks or dirt are left after using the wiper.
in the end, contact a authorised service centre
for handling.
⚠ CAUTION
When lifting and putting back the wiper, you
5. Check the wire inside the fuse. If it is blown
should not pull the wiper blade directly to
out, replace it with a spare fuse of the same
avoid deformation or even damage.
amperage.

1. Switch the power supply to the OFF mode,

and pull up the wiper control combination
switch in the direction vertical to the
steering wheel and hold for about 3 seconds.
Then the wiper will automatically reach the
service position, as shown in the figure.

6DC672024A26

200
 995F8C7650B5 70E1DDF744AB

2. Lift the wiper arm from the windscreen. (A) Wiper blade
(B) Flexible cleat
⚠ CAUTION Press down the flexible cleat and pull the wiper
 To lift the wiper, be sure to bring the wiper to blade in the direction indicated at the same
the maintenance position. Otherwise, the time until it separates from the wiper arm.
wiper will be damaged.
 Do not open the engine hood while the wiper ⚠ CAUTION
is lifted. Otherwise, the engine hood and the When the wiper blade is not installed, never
wiper will be damaged. place the wiper arm directly on the windscreen
as this will damage the windscreen.
3. Rotate the wiper blade in the direction
indicated to maximize the angle between it 5. Install a new wiper blade and return the
and the plastic connector. wiper back to the windscreen. For easy
installation, please refer to step 3 to
maximize the included angle between the
wiper blade and the plastic connector.
After installation, move the wiper up and
down to ensure that it is installed in place.
6. Reset the wiper to the initial state. The wiper
automatically resets to the initial state
when the power supply is switched to the
ON mode or the engine is started.

B26AF2BA18B2 Replace rear wiper blade

1. Lift the wiper arm from the windshield.
4. Remove the wiper blade from the wiper arm.

⚠ CAUTION
The rear wiper arm has a limited lift angle of
about 45 °. Do not over lift or use excessive
force when lifting up, otherwise there is a risk
of damage.

201
2. Pull the wiper blade in the direction shown Normally, you should not replace damaged
until the blade is free of the wiper arm. bulbs yourself, and should allow a professional
to perform this job. The primary reason is:
before replacing the bulbs you must remove
other parts from the vehicle, especially so for
those bulbs that can only be removed from
inside the engine compartment. Due to this,
we recommended that you visit authorized
service centre to replace the bulbs.

⚠ WARNING
 The inside of the bulbs is pressurized, and
D62652B4F7A6
there is a danger of injury as they may burst
during replacement!
⚠ CAUTION
 If the vehicle is equipped with a xenon lamp,
When the wiper blade is not installed, never
do not turn on the headlamp when replacing
place the wiper arm directly on the windshield
the xenon bulb. Otherwise, high voltage
as it is capable of scratching the windshield.
may cause serious bodily injury.
 Modification of external lighting and
3. Install a new wiper blade and return the
signaling devices is prohibited.
wiper back to the windshield.
 It is forbidden to add external lighting and
signaling components beyond what is in the
Bulbs
compulsory standard specifications.
The front combination lamps on a new vehicle
have been calibrated at the factory. If you often
carry heavy items in the vehicle, the front
About lamps fogged
combination lamps may need to be re-calibrated.
Under conditions such as driving or washing
The calibration of the front combination lamps
vehicle on a rainy day, there may be fog inside
should be done at authorised service centre.
the lamp cover. This is caused by the temperature
difference between the inner and outer air of
Bulb inspection the lamps and it is the same phenomenon
You should regularly check the condition of the with the window glass fogging on rainy days.
exterior lights. Burnt-out bulbs will lower It doesn't mean any problems in function.
visibility and also the vehicle's ability to signal However, when a significant amount of water
to other drivers in the dark. This means that or water vapor accumulates inside the lamp
vehicle safety will be severely compromised glass cover, please contact your authorised
under such circumstances. service centre for assistance.

Replacing bulbs ⚠ CAUTION

Bulbs should be replaced by a professional. Do not use chemical solvents or strong cleaning
agents to scrub the external lamp cover to
avoid damage to it.

202
Vehicle maintenance

Vehicle equipment Over-inflated tyres can lead to an uncomfortable

Please note that this manual contains all the ride as well as damage to the tyre due to
standard equipment, country-specific equipment uneven road surfaces, as well as uneven wear
and special equipment for this model series. to the tyres.
Thus, some equipment or features described in It is recommended that you check the tyre pressure
this manual may not be installed onto your regularly.
vehicle or are only available in some markets. Tyre pressure should be measured when the
For further configuration information, please tyre is cold. If the vehicle is parked for more
refer to relevant sales information or consult than 3 hours or driving distance is not more
with your distributor selling the vehicle to you. than 1.5 km, the measurement will get more
accurate data.
Tyre maintenance When checking tyre pressure after the tyre has
To ensure a safe drive, make sure that the tyres been warmed up (after a drive), the pressure
used suit your vehicle and that they possess a reading will be 30 to 40 kPa higher than the
good tread and appropriate tyre pressure. cold-state reading.
This is normal. Do not deflate the tyre to achieve
⚠ WARNING recommended cold-state pressure levels at this
 Do not use the excessive wear tyres or tyres point as this will lead to insufficient tyre pressure
with insufficient tyre pressure; doing so may levels.
lead to an accident, injury.
 You must abide by all manual instructions NOTICE
regarding tyre inflation and maintenance. The tyre pressure in normal tyres can go down
 Burning tyres by individuals produces toxic by 10 to 20 kPa every month.
gases. Please head to a authorised service Please check regularly.
centre for service.
Tyre wear
Tyre check
When checking tyre inflation state, you should
also check that there is no external damage,
embedded foreign objects or excessive wear, etc.
If any of the following circumstances are found,
you should replace the tyre as soon as possible:
 There is damage and bulging in the tyre
surface or side.
 There is excessive wear to the tyre tread.

FF3563DBE361
Tyre pressure
(A) Tyre wear mark
Maintaining appropriate tyre pressure levels
(B) Tyre wear mark position figure
can maximize vehicle handle ability, tyre tread
life and drive comfort.
NOTICE
Uneven wear of under-inflated tyres also impacts
Tyre wear mark position figure is a schematic
the handling of the vehicle and fuel consumption,
diagram, which is used for reference only.
and may cause tyres to go flat due to overheating.
Please refer to the actual vehicle.

203
You must replace tyres as soon as possible once When the vehicle is stationary for an extended
they are worn down to the maximum tolerable period of time, the tyre flatness can be minimized
limit. by any of the following methods:
If you continue to use tyres with shallow treads  The tyre pressure can be increased (about
or where the tyre wear mark has appeared, it 300 kPa), which cannot be used for normal
will lead to situations such as longer braking driving. Before driving, the tyre pressure
distances, difficulties in steering and cracked must be restored to the recommended tyre
tyres and possibly pressure.
accidents as a result.  Vehicles must be moved at least once every
If you find the tyres are worn unevenly, or feel 30 days (15 days best) and the movement
a certain continuous vibration when driving, go must be rotated at least 90 °.
to a authorised service centre.
When installing new tyres, tyre balancing must
Sunroof maintenance
be performed to ensure ride comfort and to
Daily maintenance frequency
prolong tyre use life.
The daily maintenance frequency depends on
the driving condition and the use frequency of
Tyre rotation
the sunroof.
In order to extend the life of the tyre and make
If you are driving through sandy areas or areas
tyre wear even, it is recommended that the tyres
with high rainfall levels, it is recommended that
of the rear and front wheels be exchanged on a
you increase the frequency of routine maintenance.
regular basis.
The tyre rotation should be done by the
⚠ CAUTION
professionals and it is recommended to be done
If the sunroof is not maintained on schedule, it
by a authorised service centre.
can lead to sunroof leaks or abnormal noise.
Adjust maintenance frequency depending on
Wheel balance
the conditions of use. For instance, in sandy
Unbalanced wheels can affect vehicle
zones or in seasons when there is higher usage,
manipulation performance and tyre life.
you should increase the frequency of routine
Even under the normal use conditions, the wheels
maintenance.
may lose their balance.
Therefore, the wheels should be balanced
Routine maintenance procedure
according to the wheel balancing parameters.
Dust and impurities may be concentrated in
the sunroof seal strip, mechanical parts or rails,
Avoid tyre flat spot
which may result in an abnormal sound or
If the vehicle is parked in a high temperature
malfunction of the sunroof and also clog the
environment for an extended period of time, a
drainage system.
slight deformation of the tyre in the contact
Regularly open the sunroof, remove dust and
position with the ground may occur, which is
impurities, and use clean cloth and water to
called "flat spot" and is normal. However, when
wipe the sunroof seal strip surface, as well as
the vehicle is running, the vehicle body and
regularly apply grease on the mechanical parts
steering wheel may shake. As the mileage
for maintenance.
increases, the tyre will get hot and return to its
original shape, and the shake will gradually
disappear.

204
Open up the sunroof and check that the sunroof When the battery shows low level, it is
does not show signs of being obstructed in the necessary to charge or replace the battery in
course of operation. If there seems to be time. Head to a authorised service centre for
obstrucion, please head to a authorised service service if you need to replace the battery.
centre for services.
Exterior maintenance
⚠ CAUTION Wash vehicle
 When the sunroof malfunctions, please head A regular vehicle wash helps to protect its
to a authorised service centre as soon as appearance. Dust and sand grains can damage
possible for check and maintenance. the paint surface while fallen leaves and bird
 In cold icing conditions, do not try to forcibly droppings can take the shine off the paint
open the sunroof to prevent damage to the surface.
sunroof motor and sunroof seals. You must
wait for the interior temperature to rise and Clean methods
for seal strips of sunroof and sunroof 1. Check that there are no fallen leaves, bird
 opening to defrost before you try to open droppings, etc., on the vehicle body.
the sunroof. Clean these dirt with a rag or a scavenger,
 Open the sunroof after washing the vehicle then rinse immediately with clean water so
in cold icing conditions. Use a piece of soft, as not to damage the vehicle body surface
dry cloth to wipe dry seal strips of sunroof finish.
2. Wash the vehicle thoroughly with water to
before driving.
remove surface dust.
 The sunroof must be closed fully before the
Clean your vehicle using the solution and a
vehicle enters a car wash facility.
soft brush, sponge, or a piece of soft cloth.
 Do not allow water jets to be pointed
3. Fill a bucket with water. Add automobile
directly at seal strips of sunroof. detergent to prepare a solution.
 Keep off the water from vehicle due to the Start your cleaning from the roof and work
deformation of the seal strip under the downwards.
pressure of the high pressure water column, 4. After washing and cleaning the entire
as a result, it may damage the seal strip. vehicle, use a dedicated wipe cloth or towel
 When driving on bumpy roads or in hilly areas, to dry off the vehicle. Do not allow the
do not open the sunroof fully for extended vehicle to dry out naturally as this may
periods of time as the vibrations may cause cause the vehicle body to lose its luster or
damage to internal sunroof components. generate water stains.
 In the rainy season, step up checks for any
sand or dust on seal strips of sunroof, and ⚠ CAUTION
remove them in a timely manner to ensure  Chemical solvent and strong cleaning
good sealing performance of sunroof. solution can cause damage to the vehicle
body paint as well as metal and plastic
components of the vehicle.
Battery
 After washing the vehicle or driving
The vehicle is equipped with a maintenance-free
through flooded road, step on the brake
battery.
pedal lightly to make sure that the brake is
The battery is located under the luggage area
functioning normally.
cover plate.

205
 When washing the vehicle in cold season, do Interior maintenance
not flush the gaps in the keyholes or doors, ⚠ WARING
etc. to prevent the lock hole or seal strip from Cleaners may contain harmful substances and
freezing.
the people may subject to a danger of injury if
 When cleaning the vehicle, it is forbidden to
affected. When cleaning the internal vehicle, it
open the fuel tank door to wash its interior.
is recommended to open the vehicle door or
vehicle window. Only the cleaner specified for
Waxing
Waxing is conducive to vehicle maintenance, vehicle cleaning shall be used and the
and the vehicle must be thoroughly cleaned instructions on the package shall be noted.
before waxing in order to ensure the effect of
waxing. NOTICE
At present, there is a wide range of car wax in  Do not allow water or any liquid come into
the market, and the car wax performance is contact with instrument panel, floor or
different, so you must be careful when selecting electrical components when cleaning the
interior as water will damage those components’
the wax. Otherwise, the wax will result in paint
function.
discoloration instead of protecting the vehicle
 Please do not clean the vehicle floor with
body.
water in order to avoid vehicle body
Under normal circumstances, the role and
corrosion.
characteristics of car wax , the degree of vehicle
age, paint color and driving environment and
Carpet
other factors should be taken into account. For
The dust on the carpet should often be cleaned
details, please contact a authorised service
by a vacuum cleaner. Too much dust will
centre or professionals.
accelerate the damage of the carpet.
Wash the carpet regularly with detergent,
Repairing paint surfaces
which can keep the carpet clean. Foam carpet
Always check to see whether there are any
cleaner should be used. To keep carpeting as
paint dropped off or scratches on the vehicle
dry as possible, do not add water to the
body surface. If such a phenomenon occurs, it
foaming cleaning solution.
should be repaired immediately to prevent
corrosion of the metal in the damaged area.
Textile fabrics
Repair paint can only be used to repair small
The dust and dirt on the textile fabrics would
areas of dropped-off paint or scratches, large
often be cleaned by a vacuum cleaner.
areas of dropped-off paint should be repaired
For general cleaning, use a clean soft cloth
by professionals.
soaked with mild and neutral soapy water. To
avoid watermarking after drying, wipe it with
Liquid leakage check
another clean, soft damp cloth and then dry in
Park your vehicle on a flat surface and leave it
the air. To remove stubborn stains, use a textile
for a while to check for leaks of fuel, oil or other
fabric cleaner. Please follow the detergent
liquids. In case of the apparent leakage, please
instructions to operate.
contact a authorised service centre for service.

206
Leather Vehicle window
Dust and dirt should be cleaned regularly by a Clean the inside and outside of the window
vacuum cleaner, especially creases and seams. with a glass detergent and wipe all the glass
Clean the leather with a soft cloth soaked with and plastic surfaces with a soft cloth or paper
water and then polish it with another soft dry towel.
cloth. If you require further cleaning, you may
use a special leather cleaner. ⚠ CAUTION
After wiping with a leather cleaner, follow up If a heating wire is attached to the inside of the
with a piece of soft and dry cloth to clean off rear vehicle window, excessive forceful wiping
any residue as quickly as possible. Never allow may cause it to shift or break. Therefore, lightly
a leather cleaner be placed on any inside wipe it along the direction of the heating wire.
surface for an extended time. Certain leather
cleaners can cause the resin or fibers in inside Seat belt
textiles to fade or break up.  If a seat belt becomes dirty, please use
neutral warm soapy water to scrub it. Do not
Rubber parts use bleach, dyes or cleaning solvents that
Affected by the environment, the rubber parts can reduce the durability of the seat belt.
may be covered with stains and tarnished on Before driving, you should allow the seat
the surface. Thus, the rubber parts should be belt to dry naturally in the air.
cleaned regularly by the rubber curing agent,  Too much dust on the seat belt guide ring
especially the worn rubber parts. can lead to slow contraction of the seat belt;
In order to avoid damage or noise, please make neutral temperature soapy water can be
sure not to use silicon contained curing agent in used to scrub the inner side of the guide ring.
the daily maintenance of rubber seals. Only
water and suitable curing agent should be used
Anti-corrosion measures
to clean.
Factors that affect the corrosion rate
Plastic parts  The accumulation of dirt, dust, or snow in
the lower part of the vehicle body can
NOTICE
accelerate corrosion.
Liquids containing alcohol or solvent (such as
 Damage to the coating or other protective
nitro diluent, cooling cleaner, fuel, perfume and
layer, arising from sand attacking or minor
cosmetics) may damage the surface of parts. Use
accident, may quicken corrosion.
microfiber soft cloth (slightly wet with water) to
 If the vehicle runs in areas where relative
clean.
humidity is high or temperature is above
freezing point, it may quicken corrosion.
Plastic components include but are not limited
 There is much salt in the air and on the road
to the following: artificial leather surface, roof
of industrial pollution areas and coastal
lining, vehicle lamp glass roller shutter, vent
regions, which may quicken the paint corrosion.
assembly and inside paint parts.
 Rising temperature may quicken the
corrosion of poorly ventilated parts.

207
Protect the vehicle from corrosion  Use a stowed towel or piece of cloth to
 Regularly use clean cold water and neutral cushion the wiper blade from the windshield
vehicle detergent to wash the vehicle so as glass.
to keep it clean.  To reduce the risk of sticking, silicone
 Regularly check whether the paint is lubricant should be applied on all door seals.
damaged. If it is, repair it as soon as possible.  Use a vehicle cover made of porous cotton to
 Regularly check the lower part of the vehicle cover the vehicle. Because plastic materials
body. If there is sand, dirt, snow, ice or other such as non-porous materials will accumulate
coverings, clean them with water as soon as moisture and is likely to damage the vehicle
possible. body paint.
 Keep the door drain hole open so as to avoid  The vehicle shall be stored in a ventilated
water logging. environment, without flammable and
 If insects, asphalt, cement or other similar explosive materials around.
objects are accumulated on the vehicle,  If possible, start the vehicle once every
clean them as soon as possible. month, and the system will monitor the
 If you always drive on a deicing salt covered battery level automatically. If the battery
road, saline-alkali land, seaside and other level is low, the engine will run into idle
roads containing salt, please wash off the charging mode. When the engine shuts
attachments at the bottom of the vehicle at down, charging is finished.
least once a month. If the battery level is normal, the engine will
 If you drive regularly on sand road, please not start and you can lock the vehicle and
consider installing mud flap behind the leave the vehicle.
wheels.  The power system is behind the luggage
area, so do not store flammable, combustible
Long-term storage of the vehicle and corrosive objects here.
The parking position of the vehicle should help  To ensure good startability and dynamic
to prevent deterioration of the vehicle condition performance, we recommend you that drive
and facilitate the restarting of the vehicle. If at least 2 hours every month.
possible, please park your vehicle indoor. If you
need to store the vehicle for an extended period
(one month or longer), please take the following
steps beforehand:
 Top up fuel.
 Clean and dry vehicle exterior thoroughly.
 Clean the inside of the vehicle to ensure it is
clean and tidy.
 Release the parking brake, and use the wheel
chock to hold against the tyres.
 Open vehicle windows on one side slightly (if
the vehicle is to be parked indoors).
 Disconnect the negative terminal of the
battery.

208
Regular maintenance table

The first regular maintenance is free of charge, and the cost of regular maintenance incurred
thereafter should be borne by the user.

NOTICE
Please strictly follow the maintenance interval indicated in the table below. If you do not have the
vehicle maintained at authorised service centre within the specified period or mileage, you will be
deemed to have waived the free maintenance service provided by our company.
“I” means “inspect”; if necessary, adjust, correct, clean or replace
“R” means “replace”
"L" means “lubricate”
“C” means “clean/clear”
* means that “the maintenance interval should be shortened accordingly under harsh conditions”
Time (month) 6 12 18 24 30 36 42 48 54 60
Item
Kilometers X 1,000 10 20 30 40 50 60 70 80 90 100

Engine oil* R R R R R R R R R R

Oil pan plug and washer* R R R R R R R R R R

Oil filter* R R R R R R R R R R

Air filter element* C R C R C R C R C R

Air conditioning filter element

C R C R C R C R C R
(A/C filter)*

Engine coolant I I I I I I I R I I

Brake fluid R R

Spark plug R R

Power battery coolant I I I I I I I I I I

Automatic transmission oil

R
(DHT oil)

Tyre rotation I R I R I R I R I R

Canister filter C C C

Throttle Valve* C C

Disk brake I I I I I I I I I I

Tyre pressure and wear I I I I I I I I I I

Ball joint and dust cover I I I I I I I I I I

209
 Time or mileage, whichever comes first
ระยะเวลา (month) 6 12 18 24 30 36 42 48 54 60
Item
Kilometers X 1,000 10 20 30 40 50 60 70 80 90 100
Essential bolts and nuts
(transmission, braking, suspension, I I I I I I I I I I
frame and turn signal lamp systems)

Radiator(appearance) I I I I I I I I I I

Battery 12V I I I I I I I I I I

Panoramic Sunroof L I I I I I I I I I

Sunroof - Water drain tube I I I I I I I I I I

Torque of bolt connecting power

I I I I I I I I I I
battery box and chassis

Power battery case I I I I I I I I I I

High/low voltage connectors of

I I I I I I I I I I
power battery

SOH of power battery I I I I I I I I I I

Four leaks of the vehicle (oil/

I I I I I I I I I I
water/electricity/air)

Vehicle Lights I I I I I I I I I I

⚠ CAUTION
 If the fuel in use contains impurities, replace the spark plug more frequently. If the idle speed of
the engine is unstable, you may need to clean or replace the spark plug.
 Since airbags are safety components and unconventional devices, they do not require routine
maintenance. If your vehicle has been in use for more than 10 years since its delivery from the
factory, please take it to authorized service centre for inspection or replacement.
 Some maintenance items may not be applicable to the vehicle you purchased due to different
vehicle configurations. Please refer to the actual vehicle models.

NOTICE
Users whose daily driving is less should still regularly go to authorised service centre every 6 months
for inspection and maintenance of their vehicles.

Regular maintenance table

210
7 Technical data
Vehicle identification 210
Overall parameters 211

211
Vehicle identification

Vehicle equipment  On the certification label below the central

Please note that this manual contains all the pillar lock.
standard equipment, country-specific equipment
and special equipment for this model series.
Thus, some equipment or features described in
this manual may not be installed onto your
vehicle or are only available in some markets.
For further configuration information, please
refer to relevant sales information or consult
with your distributor selling the vehicle to you.

Vehicle identification number

5DA9113D7F55
The vehicle identification number (VIN) is the
identity code of the vehicle and unique to every NOTICE
vehicle. It is engraved in the following locations: After using the diagnostic tool to connect the
 The upper left side of the instrument panel.
on-board diagnostic interface, you can read the
vehicle identification number in the electronic
control unit (ECU).

Engine number
GW4G15H

9828120B5453

 On front mounting beam of the front right seat.

18FFD96A28A1
The engine number is engraved on the engine
block, as shown in the figure.
NOTICE
For easy viewing, a label containing the engine
model and number is attached on the lower part
of the upper throttle of the engine intake
3CF217B15D23 manifold assembly.

212
Overall parameters

Basic parameters
For basic parameters such as the overall dimensions, quality, fuel consumption, emission standard,
maximum speed, see the official vehicle documents attached to the vehicle.

⚠ CAUTION
Unless specifically stated or separately listed parameters, all the parameters listed in this manual
are applicable to standard vehicles. For specially equipped vehicles and those vehicles produced for
other countries, some of the parameters may be different. Parameters in the official vehicle
documents attached to the vehicle shall always prevail.

Power parameters
Engine
Maximum net Maximum net Maximum
Model Type power/speed torque/speed gradeability
[kW/rpm] [N.m/rpm] [%]
GW4G15H NA Engine 70/6000 125/4400-5200 30

Drive motor assembly

Rated power/ Rated
Peak power Peak torque
Model Type speed torque
[kW] [N.m]
[kW/rpm] [N.m]
Permanent magnet
TZ220XS001 54/4700 110 115 250
synchronous motor

Generator assembly
Rated voltage Rated power/speed
Model
[V] [kW/rpm]

TY220XS001 224 39/7300

Power battery
Working
Rate voltage Rate capacity
รุ่นModel แบบType temperature
[V] [A.h]
[oC]
PE339005A Li-NMC 338.5 5 -35-65
PE338005A Li-NMC 337.6 5 -35-65
PE336005A Li-NMC 335.8 5 -35-65

213
 Tyre specifications
Items Data
215/60 R17 96H
Specifications Standard tyres
225/55 R18 98V
Tyre pressure Please refer to the tyre pressure label on the central pillar
Specifications TPU polyurethane tyre chain: thickness lower than 6 mm.
Tyre chains Installation
Front wheels
location

Wheel parameters
Items Data
Dynamic balance Unilateral [g] ≤8
parameters Bilateral sum [g] ≤15
Rear Rear wheel camber -1o30’±30’ (right-left deviation ≤30’)
wheel Rear wheel toe-in 0o7’±15’ (left and right difference ≤15’)
Kingpin backwards
3o30’±45’ (right-left deviation ≤45’)
inclination
Alignment Front-wheel camber -0o30’±45’ (right-left deviation ≤45’)
parameters Front 0o6’±5’ (Difference of ≤5′ between left
wheels Front wheel toe-in and
right wheel)
Kingpin inwards
11o9’±45’ (Reference values)
inclination

Braking parameters
Items Data
Brake pedal Free travel [mm] 4~7
Front brake pad (friction material) Minimum thickness [mm] 2
Rear brake pad (friction material) Minimum thickness [mm] 2
Front brake disk Minimum thickness [mm] 20
Rear brake disk Minimum thickness [mm] 10

214
Fluid parameters
Engine oil
Specifications of GW4G15H engine oil
If you choose API (American Petroleum Institute) standard oils, we recommend to use fully synthetic
oil:
Items Data
Ambient temperature Above -30℃ Lower temperature
Quality grade SN SN
Viscosity grade 5W-30 0W-30

If you choose ACEA (European Automobile Manufacturers’ Association) standard oils, we recommend
to use fully synthetic engine oil:
 Please use the C2 5W-30 fully synthetic oil when the temperature in your region is above -30°C.
 Please use the C2 0W-30 fully synthetic oil when your local temperature is less than the above
value.

Engine oil capacity

Capacity [L] (reference value)

Engine model When changing both the oil and

When only changing the oil
the oil filter

GW4G15H 3.1±0.1 2.8±0.1

Other types of fluids

Fluid type Specification Capacity [L] (reference value)
Transmission oil DHTF2 2.9±0.1
Ethylene glycol-based coolant 7.5 ± 0.5 (engine cooling
No.-35 (regions other than alpine region) system)
Coolant
Ethylene glycol based No. 45 (alpine 3.5 ± 0.5 (motor cooling
regions) system)
Windscreen
-- 2.5±0.2
washer fluid
Brake fluid DOT4 synthetic brake fluid 0.72±0.1

NOTICE
The above oil capacity is the design value, and the actual amount may slightly vary with products,
equipment and climate factors.

215
Seat parameters
Items Data
Seat slide rail design position Move 40 mm forward from the last position
Front seats 22°
Design angle of seat backrest
Rear seats 27°
Front seats 20°~27°
Common angle of seat backrest
Rear seats 27°

216
8 Index
Alphabetical index 219

217
Alphabetical index

A Electronic Power Steering System 119

A/C system 50 Electronic stability control 119
Airbag Emergency cut-off system 175
Front airbags 166 Emergency tyre repair 180
Side airbags 168 Engine compartment 197
Airbags Engine coolant 197
Curtain airbags 168 Engine hood 30
Anti-lock brake system 118 Engine oil 196
Event data recorder 176
B Exterior maintenance 206
Battery 206
Bottle holder 61 F
Brake fluid 197 Fatigue driving reminder system 99
Braking force assist system 118 Fluid level 195
Break-in period 72 Fluid parameters 216
Fuses 200
C
Catalytic converter 120 H
Child restraint system 170 Headrest 31
Fixing point for child seat 171 Head up display 122
Child safety lock 22 HHC (Hill-start hold control) 119
Crankcase emission control unit 158 Hill descent control system 117
Cruise control assist system 120 Horn 37
Cruise control system 100 How to jump start the vehicle 183

D I
Door lock Indicator light 128
Locking and unlocking with center control inflater and tyre repair fluid 180
buttons 19 Inside rearview mirror
Locking and unlocking with key buttons 19 Automatic anti-glare inside rearview mirror 35
Locking during emergencies 20 Manual anti-glare inside rearview mirror 35
Unlocking with the interior handle 20 Instrument
Door locks Virtual instrument 123
Locking and unlocking through the PEPS 19 Instrument brightness adjustment 43
Locking and unlocking with the mechanical Interconnection 146
key 20 Interior maintenance 207
Drive motor coolant 197
Driving mode 84 K
Key 16
E
Electronic braking force distribution system 118
Electronic parking brake 79

218
Light control combination switch 41 Secondary collision mitigation system 119
Light height adjustment 43 Single pedal function 85
Reading lamp 43 Spectacle case 60
Side roof lamp 44 Starting and shutting down vehicle 77
Steering wheel 89
O Storage case 60
On-board diagnostic system 121 Storage device 60
Outside rearview mirror 35 Sunroof
Oxygen sensor 120 Opening/closing of sunshade 26
Opening and closing the sunroof 26
P Sunroof maintenance 205
Parking assist system Sun visor 59
Anti-collision radar 92
Around view monitor 93 T
Auto parking assist system 94 Tailgate
Parking setting 96 Emergency unlock 22
Reverse camera 93 Manual tailgate 21
Reverse radar 92 Towing 186
Power supply management system 134 Traction control system 118
Power parameters 214 Tyre inflation 181
Power steering mode 89 Tyre maintenance 204
Power supply mode 76 Tyre pressure monitoring system 152
Power supply socket 61
V
R Vanity mirror 59
Radiator and fan 198 Vehicle anti-theft system 174
Refuelling 29 Vehicle identification number 213
Rollover prevention system 119 Vehicle wash/trailer mode 87
Roof rack 38 Voice assistant 202

S W
Seat Warning light 113
Driver’s seat memory 33 When the engine is overheated 185
Front manual seat 32 Window switch 24
Front power seat 33 Windscreen washer fluid 197
Power battery vent 75 Wiper control
Seat belt 161 Automatic wiper 45
Seat parameters 217 Electric front wiper 45
Seats Wireless charging for mobile phones 57
Rear armrest 34
Rear seat adjustment 33

219
220