2-Wire Transmitter with HART Protocol

TT5335A

Features:
• RTD, TC, Ohm, or mV input
• Extremely high measurement accuracy
• HART 5 protocol
• Programmable sensor error value
• For DIN form B sensor head mounting

Application:
• Linearized temperature measurement with Pt100...Pt1000,
Ni100...Ni1000, or TC sensor
• Difference or average temperature measurement of 2
resistance or TC sensors
• Conversion of linear resistance variation to a standard
analog current signal, for instance from valves or Ohmic
level sensors
• Amplification of bipolar mV signals to standard 4...20 mA
current signal
• Connection of up to 15 transmitters to a digital 2-wire
signal with HART communication

Technical characteristics
• Within a few seconds the user can program TT5335A to
measure temperatures within all ranges defined by the
norms
• The RTD and resistance inputs have cable compensation
for 2-, 3– and 4-wire connection
• The TT5335A has been designed according to strict safety
requirements and is therefore suitable for application in SIL
2 installments
• Continuous check of vital stored data for safety reasons
• Sensor error detection according to the guidelines in
NAMUR NE89

Mounting / Installation
• For DIN form B sensor heads or DIN rail mounting with the
fitting type 8421
Order:

Type
TT5335A

General Note
TT Electronics | Roxspur Measurement & Control
TT Electronics reserves the right to make changes in product specification without
2 Downgate Drive, Sheffield, South Yorkshire, S4 8BT, UK |Ph: +44 (0) 114-244-2521
notice or liability. All information is subject to TT Electronics’ own data and is
www.ttelectronics.com | [email protected]
considered accurate at time of going to print.
© TT electronics plc Issue A 04/2019 Page 1
2-Wire Transmitter with HART
Protocol
TT5335A
Environmental Conditions

Operating temperature -40°C to +85°C

Calibration temperature 20….28°C
Relative humidity < 95% RH (non-cond.)
Protection degree (encl./terminal) IP68 / IP00

Mechanical Specifications

Dimensions Ø 44 x 20.2 mm

Weight approx 50 g

Wire size 1 x 1.5 mm² stranded

wire
Screw terminal torque 0.4 Nm

Vibration IEC 60068-2-6

2… 25 Hz ±1.6 mm

25… 100 Hz ±4 g

Common Specifications

Supply
Supply voltage 8.0 …35 VDC

Isolation voltage
Isolation voltage, test / working 1.5 kVAC / 50 VAC

General Note
TT Electronics | Roxspur Measurement & Control
TT Electronics reserves the right to make changes in product specification without
2 Downgate Drive, Sheffield, South Yorkshire, S4 8BT, UK |Ph: +44 (0) 114-244-2521
notice or liability. All information is subject to TT Electronics’ own data and is
www.ttelectronics.com | [email protected]
considered accurate at time of going to print.
© TT electronics plc Issue A 04/2019 Page 2
2-Wire Transmitter with HART
Protocol
TT5335A
Common Specifications Continued

Response time

Response time (programmable) 1 ...60 s

Warm-up time 30 s

Programming Loop Link & HART

Signal / noise ratio Min. 60 dB

Accuracy Better than 0.05% of selected range

Signal dynamics, input 22 bit

Signal dynamics, output 16 bit

Effect of supply voltage change < 0.005% of span / VDC

EMC immunity influence < ±0.1% of span

Extended EMC immunity: NAMUR NE21, A criterion, burst < ±1% of span

Input Specifications

Common input specifications

Max. offset 50% of selected max. value

RTD input

RTD type Pt100, Ni100, lin. R

Cable resistance per wire (max.) 5 Ω (up to 50 Ω per wire is possible with reduced measurement
accuracy)
Sensor current Nom. 0.2 mA

Effect of sensor cable resistance ( 3-/4-wire) < 0.002 Ω / Ω

Sensor error detection Yes

General Note
TT Electronics | Roxspur Measurement & Control
TT Electronics reserves the right to make changes in product specification without
2 Downgate Drive, Sheffield, South Yorkshire, S4 8BT, UK |Ph: +44 (0) 114-244-2521
notice or liability. All information is subject to TT Electronics’ own data and is
www.ttelectronics.com | [email protected]
considered accurate at time of going to print.
© TT electronics plc Issue A 04/2019 Page 3
2-Wire Transmitter with HART
Protocol
TT5335A
Input Specifications Continued

TC input

Thermocouple type B, E, J, K, L, N, R, S, T, U, W3, W5

Cold junction compensation (CJC) < ±1.0°C

Sensor error detection Yes

Sensor error current: When detecting / else Nom. 33µA / 0µA

Voltage input

Measurement range -800… +800 mV

Min. measurement range (span) 2.5 mV

Input resistance 10 MΩ

Output Specifications

Current output

Signal range 4 ...20 mA

Min. signal range 16 mA

Load (@ current output) ≤ (Vsupply -8) / 0.023 [Ω]

Load stability ≤ 0.01% of span / 100 Ω

Sensor error indication Programmable 3.5 ...23 mA

NAMUR NE43 Upscale/Downscale 23 mA / 3.5 mA

*of span = of the presently selected range

General Note
TT Electronics | Roxspur Measurement & Control
TT Electronics reserves the right to make changes in product specification without
2 Downgate Drive, Sheffield, South Yorkshire, S4 8BT, UK |Ph: +44 (0) 114-244-2521
notice or liability. All information is subject to TT Electronics’ own data and is
www.ttelectronics.com | [email protected]
considered accurate at time of going to print.
© TT electronics plc Issue A 04/2019 Page 4
2-Wire Transmitter with HART
Protocol
TT5335A

Observed authority requirements

EMC 2014/30/EU
EAC TR-CU 020/2011

Approvals

ATEX 2014/34/EU KEMA 03ATEX1508X

IECEx KEM 10.0083X

INMETRO DEKRA 18.0002 X

DNV-GL Marine Stand. f. Certific. No. 2.4

SIL Hardware assessed for use in SIL applications

General Note
TT Electronics | Roxspur Measurement & Control
TT Electronics reserves the right to make changes in product specification without
2 Downgate Drive, Sheffield, South Yorkshire, S4 8BT, UK |Ph: +44 (0) 114-244-2521
notice or liability. All information is subject to TT Electronics’ own data and is
www.ttelectronics.com | [email protected]
considered accurate at time of going to print.
© TT electronics plc Issue A 04/2019 Page 5