DN495 4G LTE PoC Radio

Quick Start User Guide

Designed in the United Kingdom

 Quick Start User Guide V1.5

DN495 4G LTE PoC Radio

IMPORTANT BATTERY INFORMATION
By using this product you agree to the terms and conditions of Entel’s E-PoC Battery charging
Service License which can be viewed here: www.entel.co.uk/EPoC_LICENSE 1. Connect the AC adapter to the charger pod and plug in.

INTRODUCTION 2. Turn the radio off.

The Entel DN495 digital radio is designed for those users who demand the 3. Insert the battery pack into the charger pod, either with or without the radio
ultimate performance for their business critical communications. attached. The charger LED status light changes to red and charging begins.

To meet your exact requirements the radio may have been customised by your 4. When charging is complete the charger status LED changes from red
Entel dealer. These features will be explained in a separate guide issued by to green, a fully discharged battery pack will take approximately 2 hours
the dealer. (CNB420E), 3 hours (CNB450E) to re-charge.
A flashing red LED on the charger indicates there is a problem with the battery.
PACKING LIST Remove the battery from the charger and consult your Entel Dealer.

DN495 PoC Radio CAUTION

CNB4xxE Rechargeable Li-Ion battery

BATTERY PACK PRECAUTIONS
• Do not recharge the battery pack if it is already fully charged. Doing so may
CBHxxx Belt clip reduce the life of the battery pack.

CAT90 High efficiency antenna • After charging is complete, remove the battery from the charger. If the power
to the charger is turned off and on again, charging will restart and the battery
CSAHX Rapid drop-in charger will become overcharged.
• Please ensure the radio is turned off before placing it in the charger and
OPTIONAL ACCESSORIES never switch a radio on whilst in the charger.
Attaching and removing accessories • Only use Entel branded battery packs and chargers.
1. To attach an accessory, remove the accessory cover by unscrewing the • Do not short the battery terminals or dispose of the battery in a fire.
locking screw anti-clockwise (store in a safe
place). • Do not charge the radio and/or battery pack if they are wet.
2. Plug the accessory into the socket, then DANGER
carefully tighten the locking screw clockwise
until finger tight (do not overtighten or use DO NOT DISASSEMBLE OR MODIFY THE BATTERY IN ANY WAY!
any implement). Your Entel battery pack incorporates a safety circuit to avoid danger, if the
3. To remove an accessory, unscrew the safety circuit is damaged or bypassed, or the battery cells are damaged directly,
locking screw of the accessory by hand in they may generate extreme heat, smoke, rupture and emit flames.
an anti-clockwise direction. Ensure you re-fit REPAIR & MAINTENANCE
the accessory socket cover so as to protect
Repair and maintenance of this product can only be carried out by Entel.
the socket.
Any damage to the anti-tamper seal will invalidate the product approval. Should
4. To prevent corrosion or damage to the you have any difficulties in operating this product please contact your Entel
accessory connector terminals ensure either a) the accessory cover is fitted Dealer for support.
or b) an accessory is securely fitted, never leave the terminals exposed.
CONTROLS & INDICATORS

NAV KEY DISPLAY

1. On/Off/Volume control. Rotate clockwise to turn on and increase volume.

Rotate anti-clockwise to reduce volume & turn off.
2. Group (Channel) Control
2 1 3. Accessory socket
4. Push To Talk (PTT) button, press to speak and release to listen
5. Dealer programmable buttons (ask your dealer for more information)
6. LED indicator
Amber steady - Booting up
Amber / Red alternating - Not connected
5 Amber flash every 5-seconds - Radio in standby
6 Red steady - Transmitting
Green steady - Receiving
3 Amber rapid flash - In 1-2-1 call
Amber double flash - Calling / being called
4 Green rapid flash - Call hang time
Red double flash - Low battery
9 Red fast flash - Error
Talk here 7. Info button
5 8. Navigation key
9. Microphone
10 7 10. Group (Channel) list*
11. User contact list*
12. Menu*
11 12
13. Call button*
14. End-call button*
8
* If enabled by your Dealer
13 14

Full User Guide here: www.entel.co.uk/DN400_Full_User_Guide

PREPARING YOUR RADIO FOR USE SWITCHING ON, RECEPTION AND DECLARATION OF CONFORMITY
Attaching/removing the antenna SWITCHING OFF Hereby, Entel UK Limited
1. To switch on rotate the on/off/volume control (1) Declares that the radio equipment type
on the top of the radio clockwise, you will hear a DN495 is in compliance with
click from the control. Directive 2014/53/EU and Radio Equipment
A 2. When the radio has passed its diagnostic tests,
Regulations 2017.
The full text of the relevant declaration of
it will emit a fanfare tone.
conformity is available at the following
3. The radio will enter standby mode. This is internet address:
B indicated by the LED flashing Amber once every EU www.entel.co.uk/red
5 seconds, indicating the radio is ready for use. UK www.entel.co.uk/UKCA
4. Adjust the volume control (1) to select the
desired volume level. FCC APPROVAL
5. Using the Group (Channel) Control (2) ensure Contains FCC ID: XMR201911SC20AL
that you have the correct Group selected. Contains IC: 10224A-201707SC20A
6. When receiving a valid signal the LED will This device complies with part 15 of the FCC
illuminate steady green and audio will be Rules. Operation is subject to the following two
emitted from the radio’s speaker or audio conditions:
1. To attach, carefully align the antenna with the accessory (if attached). (1) This device may not cause harmful
socket. Screw in the antenna and clockwise 7. When finished using the radio, switch off by interference, and (2) This device must accept any
(taking care not to cross the thread) until it is turning the on/off/volume control (1) counter interference received, including interference that
seated firmly (A). clockwise until it clicks and the radio will be may cause undesired operation.
2. To remove, unscrew the antenna anti-clockwise switched off. This Class B digital apparatus complies with
(B). Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 Canada.
Attaching/removing the battery pack

The product shall only be put into service

C after it has been professionally configured by
a specialist radio communications dealer for
the EU member state or geographical area
it is intended to be operated within.
Intended country of use
AT BE BG CH CY CZ DE DK EE
D ES FI FR EL HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
RO SE SI SK TR UK(NI)
1. To attach (C), locate the pegs on the bottom of
the battery into the slots on the radio and pull
the 2 latches downwards, carefully pushing
the battery into the radio. Release the latches
ensuring the battery is full attached.
2. To remove (D), pull down the 2 latches and
carefully pull the battery away from radio.

www.entel.co.uk All Rights Reserved. Copyright Entel UK Ltd.