0% found this document useful (0 votes)
28 views37 pages

GW5000A

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
28 views37 pages

GW5000A

Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 37

Shenzhen Winext Technology Co., Ltd.

GW5000AIndustrial-grade gateway router

Product name: LoRaWAN gateway router

Model: GW5000A

Version: V3.4

Company name:Shenzhen Winext Technology Co., Ltd.

Address:Rm 505, Building B50, Zhongchuang Industrial Park,

Liuxian Rd, Taoyuan Street, Nanshan District, Shenzhen,

China

Tel: 0755-23990916

Fax: 0755-23990906

1
Shenzhen Winext Technology Co., Ltd.

Table of contents
Packing list ............................................................................................................................. 4

Attention .................................................................................................................................. 5

Product introduction .............................................................................................................. 6

1. Product definition ............................................................................................................ 6

2. Interface introduction ...................................................................................................... 7

3. Basic information ............................................................................................................ 9

4. Restore factory setting ..................................................................................................... 9

5. Product dimension ..........................................................................................................11

6. Technical parameter ....................................................................................................... 12

7. Label .............................................................................................................................. 13

Installation: ........................................................................................................................... 14

1. SIM card installation ..................................................................................................... 15

2. Installation of antenna ................................................................................................... 16

3. Installation of the whole kit ........................................................................................... 17

4. Power supply instruction ............................................................................................... 18

Network setting ..................................................................................................................... 19

1.Routing mode of network ............................................................................................... 19

2. Wi-Fi setting .................................................................................................................. 21

3. Check the current network status................................................................................... 23

4. Check the status of WAN(Ethernet) .............................................................................. 24

5. Check the network status of 4G ..................................................................................... 25

6. Enable/disable WAN port data entry ............................................................................. 26

Configuration/upgrade of gateway ..................................................................................... 27

1. Login.............................................................................................................................. 27

1.1. Gateway login by WI-FI hotspot of phone/laptop ................................................. 27

1.2. Gateway login on computer................................................................................... 27

2. Configuration of gateway .............................................................................................. 28

2
Shenzhen Winext Technology Co., Ltd.

2.1 Wired configuration ................................................................................................ 28

2.2 Wireless configuration ............................................................................................ 32

2.3 Firmware upgrade of gateway ................................................................................ 32

FAQ ........................................................................................................................................ 34

FCC Caution ......................................................................................................................... 37

3
Shenzhen Winext Technology Co., Ltd.

Packing list

4
Shenzhen Winext Technology Co., Ltd.

Attention
1) Gateway should be installed in the place with at least 20 degrees of depression angle

to building edges, and with at least 50cm clearance when installed at the side of a building

wall.

2) LoRa Omni directional antenna should be as far as possible from the other antennas,

and should be lower than the highest elevated point of the building.

3)The antenna should be installed vertically to the ground to achieve good effect.

4)Do the protection of lightning protection for gateway equipment, access network

cable of gateway, gateway antennas(surge arrester/lightning protector), and make sure

the antenna with the feeder to be connected to ground.


5)Using low power consumption RF coaxial cable of the feeder, as short as possible.

6)The feeder connector of antennas should be waterproof. If the feeder connector has
been flooded for a long time, the contact resistance of the connector is increased, the line
loss of the signal line is increased, and the antenna performance will be decreased.

7)If using 4G, you should choose a place with better LTE signal; The monthly traffic

plan should be more than 6G (depending on the number of nodes).

8)When the gateway is power on, the sequence of connection is: Firstly, connect one

end of network cable to gateway, and then the other end of the network cable to POE power

source or the end of POE exchanger, otherwise, the POE power source or POE exchanger

port will be damaged.

9)If using the PC side browser, it is strongly recommended that you use Google or

Firefox.

10) We suggest connecting POE splitter with backup power supply to prevent damage

of the log stored in TF card after power cut. If there is big data stored in TF card, it’ll take

long time to restore the log of the TF card after restarting the gateway, and the gateway can

work normally after you finished restoring the log of TF card.

11)The product requires professional installation and the certified antennas should be

used.

5
Shenzhen Winext Technology Co., Ltd.

Product introduction
1. Product definition
Winext Technology have launched the IoT base station gateway GW5000A based on low

power LoRaWAN protocol, which can provide low power, mobile and safe local

bidirectional communication service for IoT devices. LoRaWAN can simplify the

interconnection of device, user and network, as well as provide standard.

GW5000A is designed to be used in long range star network architectures; it can achieve

message delivery between front-end device and central network server. GW5000A is

connected to the network server via standard IP connections while front-end devices use

single-hop wireless communication to one or many GW5000A gateways.

The communication between front-end devices and GW5000A is established by

different channels and data rate, which can be negotiated in advance. In order to save the

battery life, GW5000A can maximize the power saving by implementing ADR (Adaptive

Date Rate). With our IoT technology and our base station gateway GW5000A, users can

then have their own IoT control system to achieve customized smart services, which will be

widely applied in the fields of smart parking, smart fire-fighting, energy management, asset

tracking, smart grid, industry 4.0, smart agriculture and ect in the future.

6
Shenzhen Winext Technology Co., Ltd.

2. Interface introduction

7
Shenzhen Winext Technology Co., Ltd.

No Name No Name

1 POWER indicator 2 Wi-Fi indicator

3 USB indicator 4 WAN indicator

5 LAN indicator 6 3G/4G indicator

7 SMA head port of WiFi antenna 8 SMA head port of LoRa antenna

9 SMA head port of GPS antenna 10 SMA head port of LTE antenna

11 Power indicator of SX1301 board 12 IPX port of the main antenna of 4G module

13 48V power port 14 Solar/standby power 12V grounding port

15 Solar/standby power 12V input port 16 WAN port

17 LAN port 18 Hardware reset button

19 Button to restore the factory settings

8
Shenzhen Winext Technology Co., Ltd.

3.Basic information
1)LAN IP: 192.168.3.1, DHCP server is enabled by default;

2)Web page default user: root; login password: WelcomeTo2018;

3)WAN open DHCP client by default, need to connect with router;

4) 4G/LTE: Europe LTE, US 4G, support automatic dialing by default;

5) Wifi: 2.4GHz, AP mode, max transmit power:18dBm; WiFi hotspot:GW5000_+the end

6 characters of gateway ID; Password:gateway2018better

6)WAN and 4G network, priority in using the WAN traffic by default, 4G as a backup. When

WAN is not working, switch to 4G; Gateway needs to be able to get normal access to the internet,

network delay(ping lora.smartkit.io)less than 50ms, if using Ethernet, network speed should be

above 2M; If using 4G card, the monthly data access plan should be above 6G(it depends on the

nodes quantity)

7) The default file format of TFcard: FAT32, when the rest memory less than 2G, the oldest

log files will be cleared.

8)Support foreign server, e.g. TTN;

9)Support reporting status regularly(WAN, LTE, LoRa, WiFi, TF card)

10)Support reporting LoRa configuration parameter regularly;

11)Support remote reboot;

12)Support remote administrator login and maintenance;

13)Support button or WEB operation to restore factory setting;

14)For security reasons, root login SSH2 and serial port have been disabled, and the account

of login SSH2 and serial port is not open to the public.

4. Restore factory setting


If you’ve modified some parameters of gateway, andthe gateway won't work properly, there

are two methods to restore factory settings.

1) 1st method: press the reset button on the main board for more than 8 seconds(short press

will restart the system) , the reset button is as below:

9
Shenzhen Winext Technology Co., Ltd.

2) 2nd method: Login the following interface:

Wait 1~2 minutes, then login.

10
Shenzhen Winext Technology Co., Ltd.

5. Product dimension

11
Shenzhen Winext Technology Co., Ltd.

6. Technical parameter

Technical CPU Industrial level CPU


parameter Linux system

LoRa data rate 300bps~5.4Kbps

Ethernet
communication 100Mbps
rate

LTE
communication 50Mbps
rate
Wireless
parameter

Rx sensitivity -143dBm

Communication
1xLAN ,1xWAN,1xWIFI,1xLTE module
interface

Input POE power supply with 48V input(24~48V)

Electrical Working
-30℃~65℃
specification temperature
Working
10%~90%
humidity

IP grade IP67

Dimension 288mm*215mm*59mm

Physical Installation Wall-mounted or with holding rod


parameter
Certificate CE/FCC

Thunder
optional
protection

12
Shenzhen Winext Technology Co., Ltd.

7.Label
Neutral label as below:

Remark:

The “manufacturer address xxxxxx” and “importer name xxxxx, address xxxxx” shall be

provided on the product before the product into the market.Model on label above can be replaced

by other models.

13
Shenzhen Winext Technology Co., Ltd.

Installation:

14
Shenzhen Winext Technology Co., Ltd.

1. SIM card installation


Note: Supported LTE models as below:

Open the SIM/TF card slot cover with a large screwdriver:

15
Shenzhen Winext Technology Co., Ltd.

Insert SIM card into the card slot with the chip side upwards and the notch inwards(there are

two card slots, the above one is for TF card, the below one is for SIM card):

2. Installation of antenna
The gateway is mounted on a pole and the antenna is up, and from left to right, the
antennas are: Wifi antenna, LoRa antenna, GPS antenna, and 4G antenna, fix the
antenna to the corresponding interface, as below:

16
Shenzhen Winext Technology Co., Ltd.

3. Installation of the whole kit

17
Shenzhen Winext Technology Co., Ltd.

4. Power supply instruction


A) Powered by POE, as below:

(POE ports diagram)

B) Powered by solar panel

Solar panel power supply includes: solar cell + photovoltaic controller + storage
battery

The connection as below:


Solar cell--photovoltaic controller – storage battery—gateway

Solar panel recommendation: solar panel voltage 18V, no less than 30W,
preferably with a controller; Storage battery: 12V/100Ah; The length of the 12V Power
line is less than 3m.

18
Shenzhen Winext Technology Co., Ltd.

Network setting
1. Routing mode of network
Splitter(exchanger) cable is connected to the WAN port, as below:

Remark:

The router that the gateway is connected must be able to connect to Internet, and you

should start the DHCP function for the router, and then the gateway automatically obtains

the IP. If you do not start DHCP, or because of network security management, you need

to assign a fixed IP to the gateway, then manually modify the assigned IP address in the

19
Shenzhen Winext Technology Co., Ltd.

gateway interface, as below:

Select “Network/interfaces”, enter “interface overview”, come to WAN, then you can

choose “EDIT” to modify, as below:

In “interfaces-WAN”, choose the Protocol to “DHCP client” and then

“SAVE&APPLY”, then choose “Static address” in Protocol, then click “Switch protocol”,

as below:

20
Shenzhen Winext Technology Co., Ltd.

Then, you’ll come to the below interface, and input the following items:

In “Advanced Settings”, modify the “Use gateway metric” to be 10, click

“SAVE&APPLY”, as below:

2. Wi-Fi setting
The default Wi-FiESSID: GW5000_+ the last 6 characters of gateway ID

The default password: gateway2018better

If you’d like to modify, click “Network/wireless/edit, as below:

21
Shenzhen Winext Technology Co., Ltd.

Then, you’ll come to wireless network interface, pulldown to “Interface C

onfiguration”, in the “General Setup”, you can modify “ESSID”(wifi hotspot), then click

“SAVE&APPLY”, as below:

22
Shenzhen Winext Technology Co., Ltd.

In “Wireless Security”, you can modify the password of wifi hotspot, click

“SAVA&APPLY”, as below:

3. Check the current network status


Enter “Status/Overview”, as below:

Here, it shows that WAN is online, 4G is offline.

23
Shenzhen Winext Technology Co., Ltd.

Enter “Network/Load Balance/Detailed Status”, you can check the details as

below:

4. Check the status of WAN(Ethernet)


Enter “Network/Interfaces”, as below:

Here, it shows run time and IP address, and RX and TX is not 0, it indicates the

WAN is normal.

24
Shenzhen Winext Technology Co., Ltd.

5. Check the network status of 4G


Enter:

Network->4G/LTE

When deploying gateway, the network should be stable, and if there is no wired

network, we can also use 4G network, but we should choose a position with strong 4G

signal to deploy gateway.

Qualified LTE network should meet the following 2 points:

1)Network mode display:LTE(China Mobile: TDD, China Telecom and China

Unicom: FDD

2)Signal strength above 28(the network signal should be stable the whole day)

As below, it’s under unqualified network:

Here, it’s under unqualified network: weak signal and it’s not 4G network.

25
Shenzhen Winext Technology Co., Ltd.

6. Enable/disable WAN port data entry


The WAN port data entry is enabled by default and the WAN port access gateway is

supported

Access the gateway page via the WAN port IP(e.g. if IP of the PC is 192.168.8.x, and

the gateway is 192.168.8.5, then access on the computer through a browser, enter:

192.168.8.5, you can directly access to the gateway), configuration as below(default

setting):

If you do not want to access the gateway via the WAN, you can use LAN or WiFi to enter

the Settings as follows:

26
Shenzhen Winext Technology Co., Ltd.

Configuration/upgrade of gateway
1. Login

1.1.Gateway login by WI-FI hotspot of phone/laptop

Open the phone/laptop wi-fi setting and connect the GW5000Wi-Fi hotspot(Hotspot

name: GW5000_the last 6 characters of gateway ID; Password: gateway2018better),

as below:

1.2. Gateway login on computer

Using google browser on computer, login 192.168.3.1, you’ll enter the interface of

gateway login, input username and password (Username: root; Password:

WelcomeTo2018), as below:

27
Shenzhen Winext Technology Co., Ltd.

2. Configuration of gateway
Note: The gateway configuration includes wired configuration and wireless

configuration. Wired configuration is achieved by using the network LAN port of the

computer to connect with gateway; Wireless configuration is achieve by using mobile

phone/laptop/PDA to connect to the gateway wi-fi hotspot.

2.1 Wired configuration

1)Connect the computer to the LAN port of gateway, and power on the gateway;

2)Using google browser to enter “192.168.3.1”, then you’ll come to the gateway

login interface, as below:(Username: root; Password: WelcomeTo2018)

3)Select “Network/LoRa GW/Configuration, then you’ll come to LoRa setting

interface, as below:

28
Shenzhen Winext Technology Co., Ltd.

29
Shenzhen Winext Technology Co., Ltd.

4)In the “Configuration/LoRa setting” interface, you can configure the “server address”,

“Enable LoRa Gateway”, “Store the log as txt file” ;

---Server address: choose your LoRa network server address, if there is nothing to choose,

pls click “Custom” in the bottom, and input your own LoRa network server address;

---Enable LoRa gateway: you should tick to choose it;

---Store the log as txt file: you should tick to choose it;

Finally, click SAVE&APPLY.

As below:

30
Shenzhen Winext Technology Co., Ltd.

5)Check the network status of gateway, click “Network/Load Balancing/Overview”,

as below:

31
Shenzhen Winext Technology Co., Ltd.

Here, it shows WAN is online, you can access Ethernet; 4G is offline or 4G SIM card

haven’t been installed.

6)Check the status of GPS, click “Network/LoRa GW”, you’ll come to GPS

overview, as below: (here, it shows the GPS is not in working status, as there is no

information)

7) After the above confirmation is normal, the gateway box is closed with

hexagonal screwdriver.

2.2 Wireless configuration

The steps are the similar as that of wired configuration, only displayed by

mobilephone/PDA/laptop.

2.3 Firmware upgrade of gateway

Enter “System/backup/Flash Firmware/Action”,

1)Keep settings: pls don’t tick to choose;

2)Choose file: Choose the provided version in .bin format;

3)Click “Flash image”As below:

32
Shenzhen Winext Technology Co., Ltd.

After click “Flash image” , pls wait for a moment until the upload complete, then come to

the interface of “Flash Firmware-Verify”, as below:

Note: When file is finished uploading, wait and check to make sure the Checksum is
as same as that of md5 file(which will be sent to customer together with the bin format
file), if it’s the same, pls click PROCEED button. If the Checksum is not as same as that
of md5 file, it’s possible that the upload file damages. You should click CANCEL button
to re-upload, because the damaged file can make gateway to be brick. As below:

Note: After click PROCEED button, it’s flashing the firmware, pls make sure the

33
Shenzhen Winext Technology Co., Ltd.
power supply be stable, and wait for 3~5 minutes until it finishes.

After finishing flash firmware, there is no need to enter the Web page, the gateway will

enable by default.

FAQ
1. Gateway will not work after a power failure

When there is a power failure, the log on the TF card is damaged, after restart gateway,

it’ll do self-check to automatically repair log, if TF card data quantity is large, it’ll take a

long time to repair, in the process of repairing, the gateway is not working.

Solution: enter the configuration interface of gateway (192.168.3.1) , gateway login,

select “Network/LoRa GW/Status”, click “CLEAR THE LOG OF TF CARD”, as below:

After clear the log of TF card, pls restart the gateway, then it’ll work again.

34
Shenzhen Winext Technology Co., Ltd.

2. GPS unable to locating

Enter 192.168.3.1 interface:


1) Check whether there is positioning information or not, if yes, it means GPS
is normal
2)Check whether there is time synchronization or not, as below:

If GPS is normal, the time synchronization should be less than 5 seconds, the above

picture shows “(age: 0 sec), that means the GPS is normal.

3)If GPS has no location information, you can re-plug the GPS antenna, or

repositioning in an open area, or update GPS antenna.

35
Shenzhen Winext Technology Co., Ltd.

3.Nodes cannot access to the network

1)Check whether the gateway works normally or not.

2)Check whether there is power supply for nodes

3) Nodes power on

4.LoRa signal and data rate

1)Received Signal Strength Indicator(RSSI)

125KHZband width, rate:300~5.4K bit/s, as below:

Note: the limit value of SF12 is -142. Generally speaking, if signal below -124 dBm, the

packet drop rate(PDR) will be high, normal value should be during -120dBm~ -40dBm.

2)Signal Noise Ratio(SNR)

Note: The limit value of SF12 is -20db, the limit value of SF10 is -15db. The closer it’s from

the limit value, the worse the signal.

The above data is based on the basis of the gateway test, if you use a node test, the data is

different.

36
Shenzhen Winext Technology Co., Ltd.

FCC Caution
Any Changes or modifications not expressly approved by the party responsible for

compliance could void the userʹs authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the

Following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that maycause

undesired operation.
Radiation Exp osure Statement
This equipment complies with FCC radiation exposure limits set forth for anuncontrolled

environment. This equipment should be installed and operated withminimum distance 20cm

between the radiator & your body.

Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

—Consult the dealer or an experienced radio/TV technician for help.

37

You might also like