Technical-Manual AGS-400Narrowline Capral 2022 07 01

Download as pdf or txt
Download as pdf or txt
You are on page 1of 96

400 NARROWLINE

SINGLE GLAZED (101.6MM)

TECHNICAL MANUAL
AGS 400 NARROWLINE SINGLE GLAZED (101.6mm)
The AGS 400 Narrowline framing system has set the standard for centre glazed
framing for over two decades. With an aesthetically balanced look and the option
of beveled or square finishes, the AGS 400 Narrowline is the most versatile and
adaptable framing system in the range.

With a multitude of compatible window and door suites, the AGS 400 Narrowline
offers enormous design flexibility making this product ideal for commercial or
residential projects that require a bold modern look and high levels of structural
performance.

FEATURES AND BENEFITS


ƒ 101.6mm x 44mm centre glazed framing system
ƒ Supports single glazing
ƒ Captive glazing wedge options for easier on-site glazing
ƒ Flexible design with wide range of mullion and transom options
ƒ Sub-frame options
ƒ Compatible door and window suites available
ƒ Internal and externally beaded options
ƒ Dedicated corner posts
ƒ Tested for BAL 40 compliance

MAXIMUM PERFORMANCE WINDOW ENERGY RATINGS


Serviceability Pressure 5200Pa Window ID Glazing Uw SHGC Tvw Air Inf
Ultimate Pressure 10300Pa CAP-062-09 6EcAd 4.3 0.57 0.60 0.04
Water Penetration 1500Pa CAP-062-21 10.38DLam 5.9 0.70 0.79 0.04
CAP-062-24 10.38CPClr 4.1 0.58 0.72 0.04
FRAME DIMENSIONS
CAP-062-28 10.38SnClr 4.5 0.50 0.60 0.04
Depth Height
Option 1 101.6mm 44mm CAP-062-29 8.76ESITOGy 4.1 0.31 0.31 0.04

Option 2 101.6mm 28mm CAP-062-31 6SnClr 4.6 0.54 0.61 0.04


CAP-062-35 6TS21Gy 5.2 0.26 0.09 0.04
MAXIMUM RECOMMENDED SIZE
CAP-062-40 6SolEGy 4.2 0.33 0.27 0.04
Height 4000mm
CAP-062-41 6ET 4.1 0.64 0.74 0.04
Width 2400mm
CAP-062-43 10.38VTlam 5.9 0.60 0.60 0.04
GLAZING CAPACITY CAP-062-44 6SolT 4.2 0.49 0.57 0.04
Single Glazed 4-10mm CAP-062-47 6ETGn 4.2 0.45 0.64 0.04
CAP-062-50 6EVGy 4.3 0.38 0.29 0.04
1800 ALUMINIUM (258 646) GLAZING CAPACITY
capral.com.au Acoustics (Max) 37 (0;-3)
View full list of Residential and Commercial WERS rating at capral.com.au
Capral Limited ABN 78 004 213 692
January 2022
400 Narrowline
Technical Manual History

The table below is a summary of this manual’s update history. Contact Capral for details of past updates.

RELEASE DATE UPDATE SUMMARY


01-08-2013 First Release New Manual
16-06-2016 Plain S/Mating & Midrail added
01-11-2017 Corner posts added
01-12-2017 Bushfire test report summary added
01-12-2018 General Update
01-11-2019 Drainage updated
01-01-2020 Components replaced
01-06-2021 Glazing updated

The table below shows the details of the latest manual update.

MANUAL RELEASE – 01-07-2022


DESCRIPTION AFFECTED PAGES
Manual re-badged & re-formatted. General Updates. All Throughout

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Manual History - Page 1


400 Narrowline
Technical Manual History

IMPORTANT CONDITIONS ..
By using this manual you agree to the following:

DISCLAIMER ..
Whilst best efforts have been made to ensure the details contained herein are accurate and correct, Capral is not
responsible for any loss or damage whatsoever arising as a result of any errors contained in this manual. Interpretation of
standards or codes within this manual is Capral’s interpretation of such codes. Responsibility for code compliance remains
with the user of this manual. In some cases product specifications may vary without notice. Users should not act or rely
upon any information contained in this manual without obtaining appropriate professional advice relating to their particular
circumstances. To the maximum extent permitted by law Capral disclaims all liability for loss or damage suffered by anyone
who acts or fails to act in reliance of this manual.

COPYRIGHT ..
This manual remains the property of Capral and contains information which is the subject of copyright. The manual or any
part of it may not be reproduced, copied or loaned in any form without the prior written permission of Capral. The manual is
to be returned to Capral on request.

CAPRAL SUPPLY TERMS ..


Refer to www.capral.com.au/Terms-of-Trade for Capral’s Terms and Conditions of Sale for terms of supply by Capral of its
products.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Manual History - Page 2 01-07-2022 ©


400 Narrowline
Index

SPECIFICATIONS Section 1 .
Product Specifications 1

EXTRUSIONS Section 2..


Extrusions 1-8
Extrusion Data 9

COMPONENTS Section 3..


Glazing Details 1
Components 2

CUTTING FORMULAS & BOMs Section 4..


Refer to arrangements (Section 7) for dimensions

MACHINING Section 5..


Machining – Jambs 1
Machining – Reverse Jambs 2
Machining – Sill & External Transom Drainage 3
Machining – Tubular Transom Drainage 4
Machining – Bead Drainage 5

ASSEMBLY Section 6 .
Assembly – Head & Posts 1
Assembly – Sill & Reverse Glazed Sill 2
Assembly – Mullion & Transom 3
Assembly – Reveal Head & Split Mullion 4
Assembly – Build In Brackets 5
Assembly – Glazing 6

ARRANGEMENT Section 7..


Configurations 1
Vertical Arrangement 01, 02 & 03 – Head, Transoms & Sill 2
Vertical Arrangement 02 & 03 – Reverse Glazing & Midrail 3
Vertical Arrangement 02 & 03 – Alt. Head Fixings 4-5
Horizontal Arrangement 04 & 05 – Jamb & Mullions 6
Horizontal Arrangement 04, 06 & 08 – Alt. Jamb & Self Mating Mullions 7
Horizontal Arrangement 07 – 90º & 180º Couplers 8
Horizontal Arrangement 07 – 2/3 Way Corner Post, Coupler & Mullion 9
Arrangement – Interior Glazed Partition 10

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Index - Page 1


400 Narrowline
Index

TESTING Section 8.
Structural & Water Test Report Summary 9962S3A – F.F / F 1
Structural & Water Test Report Summary 9962S3B – F.F / F 2
Structural & Water Test Report Summary – F.F 3 - 10
Structural & Water Test Report Summary – F/F 11 - 17
Structural & Water Test Report Summary – F.F 18 - 30
Bushfire Test Report Summary 44400500.1 - F 31
Acoustic Test Report Summary ATF 1152 & ATF 1153 – F.F / F 32
Acoustic Test Report Summary 4870-25 & 4870-16 – F.F 33

SPAN TABLE Section 9.


Span Table – Light Mullion – EN9457 / EN9499 1
Span Table – Medium Mullion – EN5010 / EN9499 2
Span Table – Heavy Mullion – EN5011 / EN9499 3
Span Table – Light Split Mullion – EP5408 / EP5408 4
Span Table – Medium Split Mullion – EP5408 / EP5409 5
Span Table – Heavy Split Mullion – EP5409 / EP5409 6
Span Table – 180° Box Coupler – EN5010 / EP17034 / EN5010 7
Span Table – 90° Box Coupler – EN5010 / EP17033 / EN5010 8
Span Table – Corner Mullion – EN9499 / EN5014 / EN9499 9
Span Table – Plain Mullion – EP15841 / EP15841 10
Span Table – Light Plain / Pocket Mullion – EP15841 / EP5408 11
Span Table – Heavy Plain / Pocket Mullion – EP15841 / EP5409 12
Span Table – Tubular Transom – EN5021 13
Span Table – 2 Piece Transom – EN5020 / EN9499 14
Span Table – Midrail – EN2849 15
Maximum Glass Thickness Table – Tubular Transom – EN5021 16
Maximum Glass Thickness Table – 2 Piece Transom – EN5020 / EN9499 17
Maximum Glass Thickness Table – Midrail – EN2849 18

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Index - Page 2 01-07-2022 ©


400 Narrowline
Product Specifications

SIZE LIMITATIONS

Mullion Height Mullion Spacing


Minimum: 600mm Minimum: 300mm
Maximum: 4000mm Maximum: 2400mm

Transom Width Transom Spacing


Minimum: 300mm Minimum: 300mm
Maximum: 3000mm Maximum: 1500mm

NOTE: Refer to the information below & Span Tables to check the maximum sizes that can be achieved for the
assigned performance requirements of the installation.

SERVICEABILITY PRESSURE & WATER PERFORMANCE


Residential & Commercial Applications:
The Serviceability Pressures listed in the Span Tables have not been limited by a water performance.
Where water performance is necessary the product should be limited to the following maximum water ratings or
serviceability pressures:

Max. Water Max. Serviceability


Configuration Sill Transom Pressure (Pa)
Rating (Pa)
(Max. Water Rating / 30%)
F.F / F EN5020 / EN5032 EN9499 / EN5020 / EN5032 1000 3333
(Roll in Wedges)
F.F / F EN5020 / EN5032 EN9499 / EN5020 / EN5032 1000 3333
(Silicone Glazed)
EN5032 / EN5020 N/A 920 3067
F.F
EN5032 / EN5020
(Roll in Wedges)
(Internal Bead)
N/A 900 3000
F.F EN5032 / EN5020 N/A 1510 5033
(Silicone Glazed)
EN5020 / EN5032 EN5021 / EN5032
F/F (Internal Bead) (Internal Bead)
913 3043
(Roll in Wedges) EN5020 / EN5032 EN5020 / EN9499 / EN5032 300 1000
EN5020 / EN5032 EN5021 / EN5032
F/F (Internal Bead) (Internal Bead)
1521 5070
(Silicone Glazed) EN5020 / EN5032 EN5020 / EN9499 / EN5032 1513 5043

Note: The use of a standard Subsill has been assumed for the Water Performance Ratings listed above.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-08-2013
01-07-2022 Sec1 Specifications - Page 1
400 Narrowline
Extrusions Scale 1:1

P.P.
44

IDENTIFIED BY
SINGLE PIP

101.6.

EN9457
LIGHT WEIGHT FRAME
Paint Perimeter: 196mm
Anodised Perimeter: 586mm

P.P.
44

IDENTIFIED BY
DOUBLE PIPS

101.6.

EN5010
STANDARD FRAME
Paint Perimeter: 195mm
Anodised Perimeter: 578mm

P.P.
44

IDENTIFIED BY
TRIPLE PIPS

101.6.

EN5011
HEAVY DUTY FRAME
Paint Perimeter: 195mm REFER TO SUB SILL & SUB FRAME TECHNICAL
Anodised Perimeter: 571mm MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec2 Extrusions - Page 1


400 Narrowline
Extrusions Scale 1:1

P.P.

28

101.6.

EN5016
NARROW FRAME
Paint Perimeter: 176mm
Anodised Perimeter: 514mm

P.P.
47

25
101.6.

EP4845
EXTERNAL FLANGE FRAME
Paint Perimeter: 170mm
Anodised Perimeter: 537mm

P.P.
44

101.6.

EN5022
PLAIN FRAME
Paint Perimeter: 212mm
Anodised Perimeter: 466mm REFER TO SUB SILL & SUB FRAME TECHNICAL
MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec2 Extrusions - Page 2 01-07-2022 ©


400 Narrowline
Extrusions Scale 1:1

22

P.P.
101.6.

EP5408
LIGHT S / M MULLION
Paint Perimeter: 130mm
Anodised Perimeter: 496mm
22

P.P.
101.6.

EP5409
HEAVY S / M MULLION
Paint Perimeter: 130mm
Anodised Perimeter: 510mm
22

P.P.
101.6.

EP15841
PLAIN S / M MULLION
Paint Perimeter: 268mm
Anodised Perimeter: 401mm

REFER TO SUB SILL & SUB FRAME TECHNICAL


MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec2 Extrusions - Page 3


400 Narrowline
Extrusions Scale 1:1

P.P.

44
101.6.

EN5020
STANDARD SILL / TRANSOM
Paint Perimeter: 130mm
Anodised Perimeter: 480mm

P.P.

44

101.6.

EN5021
TUBULAR TRANSOM
Paint Perimeter: 195mm
Anodised Perimeter: 442mm

100mm FLUSHLINE - 82.5

101.6mm NARROWLINE - 80

EP10536
FLUSHLINE / NARROWLINE COUPLER
Paint Perimeter: NA
Anodised Perimeter: 258mm

REFER TO SUB SILL & SUB FRAME TECHNICAL


MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec2 Extrusions - Page 4 01-07-2022 ©


400 Narrowline
Extrusions Scale 1:1

43 14
P.P. P.P.

22
23

EP12761 EK7556
BRACED BEAD MIDRAIL BEAD
Paint Perimeter: 127mm Paint Perimeter: 100mm
Anodised Perimeter: 190mm Anodised Perimeter: 137mm
REFER TO SECTION 9 SPAN TABLES
FOR RECOMMENDED USAGE

43
P.P.
23

EN5032
SQUARE BEAD
Paint Perimeter: 100mm
110
Anodised Perimeter: 206mm

43

P.P.
23

P.P. 44

EN5031 EN2849
SLOPING BEAD 110mm MIDRAIL
Paint Perimeter: 100mm Paint Perimeter: 242mm
Anodised Perimeter: 184mm Anodised Perimeter: 524mm

REFER TO SUB SILL & SUB FRAME TECHNICAL


MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec2 Extrusions - Page 5


400 Narrowline
Extrusions Scale 1:1

101.6.

EP17033
90° POST
Paint Perimeter: 344mm
Anodised Perimeter: 515mm
101.6.

P.P.
101.6.
P.P.

EP17034
180° POST
Paint Perimeter: 344mm
Anodised Perimeter: 515mm
101.6.

REFER TO SUB SILL & SUB FRAME TECHNICAL


MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec2 Extrusions - Page 6 01-07-2022 ©


400 Narrowline
Extrusions Scale 1:1

101.6.

P.P.

EN5014
2 / 3 WAY CORNER
Paint Perimeter: 231mm
Anodised Perimeter: 769mm
101.6.

80
20

P.P.
39

EN5029
BUILD IN FILLER
Paint Perimeter: 145mm
Anodised Perimeter: 327mm

P.P.
21

141

EP10567
FIXING ADAPTOR
Paint Perimeter: 100mm REFER TO SUB SILL & SUB FRAME TECHNICAL
Anodised Perimeter: 395mm MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec2 Extrusions - Page 7


400 Narrowline
Extrusions Scale 1:1

80
P.P. 16.5

P.P.
18

11
EN9499 EK5925
POCKETED FILLER FLUSH FILLER
Paint Perimeter: 100mm Paint Perimeter: 100mm
Anodised Perimeter: 307mm Anodised Perimeter: 100mm

15.5

P.P.
80
P.P.

12.5

16
7

EN5028 EP5447
FLAT FILLER NARROW FRAME HOOK BEAD
Paint Perimeter: 100mm Paint Perimeter: 100mm
Anodised Perimeter: 223mm Anodised Perimeter: 100mm
35
42

20

P.P. P.P.

25

80 EK9111
25 x 20 x 1.6 TRIM ANGLE
EQ6368 Paint Perimeter: 100mm
NAILING FIN ADAPTOR Anodised Perimeter: 100mm
Paint Perimeter: 152mm
Anodised Perimeter: 291mm

80
25

EP12061
REVEAL FIN ADAPTOR P.P.
Paint Perimeter: NA
19.5

Anodised Perimeter: 326mm


25

EK9216
38.5

25 x 25 x 1.6 TRIM ANGLE


Paint Perimeter: 100mm
Anodised Perimeter: 100mm

REFER TO SUB SILL & SUB FRAME TECHNICAL


MANUAL FOR SUB FRAME INFORMATION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec2 Extrusions - Page 8 01-07-2022 ©


400 Narrowline
Extrusion Data

Structural Properties *
Extrusion Description
Ixx (103mm4) Iyy (103mm4) Zxx (103mm3) Zyy (103mm3)
EK5925 Flush Filler 0.452 1.356 0.062 0.166
EK7556 Midrail Bead 5.135 2.142 0.351 0.279
EK9111 25 x 20 x 1.6mm Trim Angle 2.535 4.411 0.169 0.253
EK9216 25 x 25 x 1.6mm Trim Angle 4.739 4.739 0.261 0.261
EN2849 110mm Midrail 882.009 229.611 14.514 9.548
EN5010 Standard Frame 112.318 670.803 3.868 13.156
EN5011 Heavy Duty Frame 125.145 767.577 4.254 15.062
EN5014 2/3 Way Corner 1394.889 619.712 26.443 12.194
EN5016 Narrow Frame 43.541 493.938 2.474 9.683
EN5020 Standard Sill 88.688 561.702 3.923 10.027
EN5021 Tubular Transom 138.075 544.145 5.088 9.249
EN5022 Plain Frame 117.515 704.801 3.756 13.929
EN5028 Flat Filler 0.736 133.141 0.150 3.329
EN5029 Build In Filler 13.864 128.100 0.524 3.178
EN5031 Sloping Bead 5.484 21.382 0.371 1.059
EN5032 Square Bead 9.507 33.066 0.535 1.513
EN9457 Lightweight Frame 99.719 588.566 3.409 11.541
EN9499 Pocketed Filler 7.966 135.101 0.622 3.377
EP10536 Flushline / Narrowline Coupler 3.722 260.478 0.379 6.322
EP10567 Fixing Adaptor 9.174 574.695 0.510 7.427
EP12061 Reveal Fin Adaptor 12.266 146.520 0.545 3.443
EP12761 Braced Bead 11.579 39.535 0.685 1.789
EP15841 Plain S/M Mullion 38.328 557.011 1.122 10.640
EP17033 90º Post 1625.043 1629.309 27.836 27.961
EP17034 180º Post 1552.986 1714.435 30.565 28.101
EP4845 External Flange Frame 56.903 547.520 1.605 9.971
EP5408 Light S/M Mullion 45.716 585.629 1.428 11.228
EP5409 Heavy S/M Mullion 80.458 1076.423 2.745 18.905
EP5447 Narrow Frame Hook Bead 0.816 0.789 0.098 0.076
EQ6368 Nailing Fin Adaptor 21.187 135.920 0.645 3.190

* NOTE: The structural properties listed above are using the orientations as listed within the extrusion pages.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-11-2017
01-07-2022 Sec2 Extrusions - Page 9
400 Narrowline

DRY GLAZING - 16mm Pocket


GLASS SIZE WEDGE GAP WEDGE GAP
4mm 300013 (315788*) 5mm 300004 8mm
5mm 300013 (315788*) 5mm 300003 7mm
6mm 300013 (315788*) 5mm 300013 5mm
8mm 300001 (315787*) 3mm 300013 5mm
10mm 300001 (315787*) 3mm 300001 3mm
* Captive Wedge Alternative

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec3 components - Page 1


400 Narrowline
Components Not to Scale

321150 321149
400 SILL GASKET 400 FRAME GASKET
EACH EACH
(SPD04747) (SPD04746)

NOTE: EACH GASKET WHEN ASSEMBLED MEASURES 0.35MM. PLEASE TAKE THIS NOTE: EACH GASKET WHEN ASSEMBLED MEASURES 0.35MM. PLEASE TAKE
INTO CONSIDERATION WHEN DETERMINING SILL/TRANSOM CUT LENGTHS. THIS INTO CONSIDERATION WHEN DETERMINING HEAD CUT LENGTH.

316051 300163
CO-EXT EXPANSION JOINT SEAL BUILD IN BRACKET
500m ROLL - SC EACH
(10148) (M400565)

SPLIT MULLION

300059 300058
10g x 25mm SS PAN SCREW 10g x 12mm CSK SCREW
EACH EACH
(M028598) (M028354)

FRAME REVEAL FIXING ADAPTOR

322026 307411
POCKET FILLER PLASTIC NAILING FIN
EACH - CLEAR CORNER COVER
(SPD04773) EACH
(SPD01182)
TRIM TO SUIT ALT TO 311592

311592
REINFORCED FOIL TAPE
50m ROLL
(PT018)

NON STOCKED ITEMS


SILICONE
SMALL JOINT SEALANT
RECOMMENDED FOR COMPATIBILITY WITH END DAMS:
- DOW CORNING 739 - DOW CORNING 795
- DOW CORNING 791 - DOW CORNING 580 CLOSED CELL BACKING ROD

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec3 components - Page 2 01-07-2022 ©


400 Narrowline
Cutting Formula and BOM

REFER TO Sec7 FOR DIMENSIONS

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022
DD-MM-YYYY Sec4:Formulas - Page 1
400 Narrowline
Machining - Jambs Scale 1:2

21 21 Ø5 21
21 TYP
CTR CTR CTR CTR

NARROW

CTR
24
HEAD FRAME
CTR
40

Ø5
TYP

Ø5
TYP

FLANGE

CTR
21
FRAME

TUBULAR
CTRS
36
TRANSOM CTR
4

33 33
CTR CTR

2 PIECE
CTRS
36

CTRS
25.5

TRANSOM
CTR
14

CTR
4

MIDRAIL
CTRS
76.5
CTR
14

SILL
CTR
40

CTR
4

VARIOUS VARIOUS
ALL JAMB & MULLION SECTIONS ALL JAMB & MULLION SECTIONS

10 10 22 22
CTR CTR CTR
CTR
EN9499 . EN5028 EN9499 . EN5028
POCKETED . FLAT FILLER POCKETED . FLAT FILLER

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec5 Machining - Page 1


400 Narrowline
Machining - Reverse Jambs Scale 1:2

21 21 *NOTE: FULL HEIGHT POCKETED OR FLAT FILLER TO BE


CTR CTR USED IN JAMB

HEAD
CTR
40

Ø5
TYP

Ø10
SEE NOTE*
REVERSE
CTRS

TUBULAR
36

TRANSOM 12.5
CTR

Ø5
TYP
CTR
4

33 33
CTR ℄ CTR

Ø10 Ø10
SEE NOTE* SEE NOTE*
REVERSE 2
CTRS

PIECE
36

CTRS
25.5
TRANSOM
CTR
23
CTRS
10
CTR
3.5

CTR
90

CTRS
76.5
14
CTR

REVERSE
CTR

SILL
40

CTR
3.5

REVERSE MIDRAIL

VARIOUS VARIOUS
ALL JAMB & MULLION SECTIONS ALL JAMB & MULLION SECTIONS

10 10 22 22
CTR CTR CTR CTR

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec5 Machining - Page 2 01-07-2022 ©


400 Narrowline
Machining - Sill & External Transom Drainage Scale 1:2

21
CTR

Ø10

CTR
50
TYP

CTR
50

EN5020
STANDARD SILL
WITH SUB SILL ONLY
3.2

50 50 EN5020
CTR 25 25 CTR EXTERNAL TRANSOM
NOT SUITABLE FOR REVERSE

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec5 Machining - Page 3


400 Narrowline
Machining - Tubular Transom Drainage Scale 1:2

CTR
50

TYP (3)
25
CTR
50

EN5021
EXTERNAL TUBULAR TRANSOM
NOT SUITABLE FOR REVERSE

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec5 Machining - Page 4 01-07-2022 ©


400 Narrowline
Machining - Bead Drainage Scale 1:2

DRAINAGE OPTION 1 - ALL BEADS

5.5
5

EK7556 EN5032 . EP12761


25 50
MIDRAIL BEAD SQUARE . BRACED BEAD
TYP CTR
50
CTR

6.5

EN5031
25 50
SLOPING BEAD
TYP CTR
50
CTR

DRAINAGE OPTION 2 - ALL BEADS

EK7556 EN5032 . EP12761


MIDRAIL BEAD SQUARE . BRACED BEAD

EN5031
SLOPING BEAD 30° 30°

ADDITIONAL DRAINAGE - EXTERNAL 2 PIECE TRANSOM & MIDRAIL ONLY


6

AS ABOVE

AS
ABOVE
EK7556 EN5032 . EP12761
MIDRAIL BEAD 25 50
SQUARE . BRACED BEAD TYP CTR
50
6

AS
ABOVE

EN5031 25 50
SLOPING BEAD TYP CTR
50

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec5 Machining - Page 5


400 Narrowline
Assembly - Head & Posts Not To Scale

* EACH GASKET WHEN ASSEMBLED MEASURES 0.35MM. PLEASE TAKE


THIS INTO CONSIDERATION WHEN DETERMINING HEAD, SILL &
FRAME HEAD TRANSOM CUT LENGTHS.

10g x 25mm SS PAN SCREW


300059
EXPOSED SCREWS AND HOLES TO BE
SEALED INCLUDING ANY UNUSED
HOLES CREATED BY A PUNCH TOOL

POCKETED FILLER
EN9499
150mm @ 600 CTRS
FRAME END GASKET*
321149
ALT. USE SMALL JOINT SEALANT
STANDARD FRAME
EN5010

FRAME (HEAD)

FULL LENGTH CAULKING


PRIOR TO APPLICATION

ASSEMBLED FRAME

180° POST
EP17034

180° POST
90° POST SIMILAR

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© DD-MM-YYYY
01-07-2022 Sec6 Assembly - Page 1
400 Narrowline
Assembly - Sill & Reverse Glazed Sill Not To Scale

* EACH GASKET WHEN ASSEMBLED MEASURES


0.35MM. PLEASE TAKE THIS INTO CONSIDERATION
WHEN DETERMINING HEAD, SILL & TRANSOM CUT
LENGTHS.
STANDARD FRAME
EN5010

STD SILL POCKETED FILLER SQUARE BEAD


EN9499 EN5032
150mm @ 600 CTRS APPLIED AFTER GLASS

10g x 25mm PAN SCREW


300059
EXPOSED SCREWS AND HOLES TO BE
SEALED INCLUDING ANY UNUSED
HOLES CREATED BY A PUNCH TOOL

SUB SILL STANDARD SILL


REFER TO SUB FRAME MANUAL EN5020
FOR REVEAL SUB SILL

POCKETED FILLER
EN9499
150mm @ 600 CTRS

STANDARD FRAME
EN5010

SILL END GASKET*


321150
ALT. USE SMALL JOINT SEALANT
POCKETED FILLER SQUARE BEAD
EN9499
EN5032
150mm @ 600 CTRS OR
SEAL INSIDE LEG INTO POSITION FULL LENGTH
FULL LENGTH WITH REVERSE TRANSOMS
SEAL BOTH ENDS WITH SMALL JOINT SEALANT
ALT. FLAT FILLER EN5028
APPLY AFTER GLASS

10g x 25mm PAN SCREW


300059
EXPOSED SCREWS AND HOLES TO BE
SEALED INCLUDING ANY UNUSED
HOLES CREATED BY A PUNCH TOOL

STANDARD SILL
EN5020

SUB SILL POCKETED FILLER


REF. TO SUB SILL & EN9499
SUB FRAME MANUAL 150mm @ 600 CTRS

REVERSE GLAZED SILL

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec6 Assembly - Page 2 DD-MM-YYYY


01-07-2022 ©
400 Narrowline
Assembly - Mullion & Transom Not To Scale

* EACH GASKET WHEN ASSEMBLED


MEASURES 0.35MM. PLEASE TAKE THIS INTO
STANDARD FRAME CONSIDERATION WHEN DETERMINING HEAD,
JAMB SIMILAR SILL & TRANSOM CUT LENGTHS.
TUBULAR TRANSOM 10g x 25mm SS PAN SCREW
300059
EXPOSED SCREWS AND HOLES TO BE
SEALED INCLUDING ANY UNUSED
HOLES CREATED BY A PUNCH TOOL

POCKETED FILLER
EN9499
SEAL INTO POSITION FULL LENGTH

SILL END GASKET*


321150
ALT. USE SMALL JOINT SEALANT

TUBULAR TRANSOM
EN5021

POCKET FILLER
320026
ENTIRE POCKET COMPLETELY
SEALED OVER POCKET FILLER SQUARE BEAD
WITH SILICONE EN5032
APPLY AFTER GLASS
CO-EXT EXPANSION
JOINT SEAL
316051

LIGHT S / M MULLION
EP5408
SEAL BOTTOM 100mm

DRAIN HOLE Ø9mm


SILL END GASKET*
321150
ALT. USE SMALL JOINT SEALANT

SQUARE BEAD
EN5032
APPLY AFTER GLASS

STANDARD SILL/TRANSOM
EN5020

POCKETED FILLER
EN9499
SEAL INTO POSITION FULL LENGHT

REVERSE GLAZED
2-PIECE TRANSOM
SUB SILL MUST BE USED

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© DD-MM-YYYY
01-07-2022 Sec6 Assembly - Page 3
400 Narrowline
Assembly - Reveal Head & Split Mullion Not To Scale

REVEAL
REVEAL

STAPLE OR
OTHER FIXING
STAPLE OR OTHER FIXING REINFORCED FOIL TAPE
311592
SEAL OVER MULLION OPENING
REINFORCED FOIL TAPE
311592
SEAL CORNERS & FRAME POCKET
ALT. USE 307411 NAILING FIN COVER

MULLION WITH REVEAL

HEAD WITH REVEAL

CO-EXIT EXPANSION
JOINT SEAL
316051

SILICON SEAL
BOTTOM 100mm

LIGHT S / M MULLION
EP5408 INSTALLED SPLIT MULLION
VIEW FROM INSIDE
SILL END GASKET*
321150
ALT. USE SMALL JOINT SEALANT

STANDARD SILL
EN5020

10g x 25mm PAN SCREW


300059
EXPOSED SCREWS AND HOLES TO BE
SEALED INCLUDING ANY UNUSED
HOLES CREATED BY A PUNCH TOOL

POCKETED FILLER
EN9499
SEAL INTO POSITION FULL LENGTH

SQUARE BEAD
EN5032
APPLIED AFTER GLASS

SUB SILL
EN6323
REFER TO SUB FRAME MANUAL
FOR REVEAL SUB SILL

SPLIT MULLION

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec6 Assembly - Page 4 01-07-2022 ©


400 Narrowline
Assembly - Build In Bracket Not to Scale

PRECAST CONCRETE CONSTRUCTION

BUILD IN BRACKET 300163


300163

EN5010

SILICONE BEAD

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec6 Assembly - Page 5


400 Narrowline
Assembly - Glazing Not To Scale

CAPTIVE WEDGE INSTALLED DURING


FRAME ASSEMBLY

TILT GLASS INTO JAMB

EQUAL COVER EQUAL COVER

CENTRE GLASS IN JAMBS

LIFT GLASS INTO HEAD SNAP ON BEAD


INSERT SETTING BLOCKS ROLL IN GLAZING WEDGE/S

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec6 Assembly - Page 6 01-07-2022 ©


400 Narrowline
Configurations Not to Scale

01

01

08 08

02

02

03

03

SUB FRAME

04 04 05 05 06 06 07 07

JAMB STANDARD SELF MATING 2 / 3 WAY


MULLION MULLION POST

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec7 Arrangements - Page 1


400 Narrowline
Vertical Arrangement 01, 02 & 03 - Head, Transoms & Sill Scale 1:2

REFER TO SUB SILL & SUB FRAME TECHNICAL MANUAL FOR SUB FRAME DETAILS

SUB HEAD
1 POCKETED FILLER
SUB HEAD EN9499
150mm @ 600 CTRS

MIN
20 SMALL BULB SEAL
300841
44

STANDARD FRAME
9
GLASS HEIGHT=

EN5010
DOH +18
DOH

GLAZING WEDGE
2
9

SQUARE BEAD
TUBULAR EN5032
TRANSOM
44

POCKET FILLER
322026

TUBULAR TRANSOM
9
GLASS HEIGHT=

EN5021
DOH +18
DOH

2 STANDARD SILL
9

EN5020
2 PIECE GLASS SETTING BLOCK
TRANSOM SLOPING BEAD
44

EN5031
POCKETED FILLER
OUTSIDE

EN9499
9
GLASS HEIGHT=
DOH +18
DOH

BRACED BEAD
EP12761
STANDARD SILL
9

EN5020

SUB SILL END DAM


44

3
SILICONE SEAL
SILL

SUB SILL
CLOSED CELL
BACKING ROD

SUGGESTED SLAB SET-DOWN


FOR FRAME EMBEDMENT
62

REBATE SHOWN ASSUMES A PACKING


6
38

ALLOWANCE OF 6mm MAX

2.5 6 2.5 6
6

REF.129 REF. 129

EP5693 SHOWN EP5693 SHOWN


SIZE VARIES FOR OTHER SUB SILLS SIZE VARIES FOR OTHER SUB SILLS
REF. SUB SILLS & SUB FRAMES MANUAL REF. SUB SILLS & SUB FRAMES MANUAL

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec7 Arrangements - Page 2 01-07-2022 ©


400 Narrowline
Vertical Arrangement 02 & 03 - Reverse Glazing & Midrail Scale 1:2

REFER TO SUB SILL & SUB FRAME TECHNICAL MANUAL FOR SUB FRAME DETAILS

MIDRAIL BEAD
EK7556

2
REVERSE MIDRAIL 110mm MIDRAIL
110

MIRROR FOR EXTERNAL BEADED EN2849


DAYLIGHT OPENING = DOH
GLASS HEIGHT = DOH + 18
OUTSIDE

GLAZING WEDGE
2 GLASS SETTING BLOCK
REVERSE
44

POCKET FILLER
TRANSOM 322026

STANDARD SILL
EN5020

POCKETED FILLER
DAYLIGHT OPENING = DOH
GLASS HEIGHT = DOH + 18

EN9499
TRANSOM HEIGHT = TH

SQUARE BEAD
EN5032

SILICONE SEAL
CLOSED CELL BACKING ROD
44

3 SUB SILL
SUB SILL END DAM
REVERSE SILL POCKETED FILLER
EN9499
150mm @ 600 CTRS

REVERSE GLAZING
REVERSE BEADED FRAMES ARE ONLY POSSIBLE IF DRAINAGE IS PROVIDED
THROUGH MULLIONS & JAMBS & MUST BE USED WITH SUBSILL. REFER
SECTION 5, PAGE 5

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec7 Arrangements - Page 3


400 Narrowline
Vertical Arrangement 02 & 03 - Alt. Head Fixings Scale 1:2

NOTE: BELOW INSTALLATION METHODS ARE INDICATIVE ONLY. HEADS SHOWN AS EXAMPLE, JAMBS SIMILAR

EXTERNAL CLADDING
LINTEL
INTERNAL
WALL LINING
ARCHITRAVE
SARKING
NAILING FIN ADAPTOR
EQ6368
BUILD IN FILLER
EN5029
1 REVEAL FIN ADAPTOR
HEAD EP12061

FIXING ADAPTOR FOR FLASHING BY OTHERS


TIMBER REVEAL
100mm REVEAL
44

10g x 12mm CSK SCREW


FIX @ APPROPRIATE CTRS
300058

STANDARD FRAME
EN5010
POCKET FILLER
322026
OUTSIDE

1
25 x 25 x 1.6mm ANGLE
ANGLE FIX EK9111

HEAD POCKETED FILLER


EN9499
150mm@600 CTRS
44

25 x 20 x 1.6mm ANGLE
EK9111
STANDARD FRAME
EN5010

GLAZING WEDGE

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec7 Arrangements - Page 4 01-07-2022 ©


400 Narrowline
Vertical Arrangement 02 & 03 - Alt. Head Fixings Scale 1:2

NOTE: BELOW INSTALLATION METHODS ARE INDICATIVE ONLY. HEADS SHOWN AS EXAMPLE, JAMBS SIMILAR

SARKING

LINTEL

INTERNAL
WALL LINING

FLASHING BY
OTHERS

15
1 STAPLE OR
OTHER FIXING
HEAD
INLINE REVEAL
ARCHITRAVE
44

80mm REVEAL
10g x 12mm CSK
SCREW
FIX @ APPROPRIATE
CTRS

FRAME
EN5010
OUTSIDE

50
30

1
HEAD FIXING ADAPTOR
FIXING ADAPTOR FOR EP10567
CONCRETE 10g x 12mm CSK SCREW
44

300058
SILICONE SEAL
STANDARD FRAME
EN5010

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec7 Arrangements - Page 5


400 Narrowline
Horizontal Arrangements 04 & 05 - Jamb & Mullions Scale 1:2

REVERSE GLAZING
REVERSE BEADED FRAMES ARE ONLY POSSIBLE IF DRAINAGE IS PROVIDED
THROUGH MULLIONS & JAMBS & MUST BE USED WITH SUB SILL. REFER Sec5
4 5
STANDARD LIGHT
JAMB MULLION

SILICONE SEAL POCKETED FILLER GLAZING LIGHTWEIGHT POCKET FILLER ^


CLOSED CELL EN9499 WEDGE FRAME 322026
150mm @ 600 CTRS AT TRANSOM
BACKING ROD EN9457
STANDARD FRAME TRIMMED WHERE REQ.
EN5010

GLASS WIDTH = DOW + 18


44 DAYLIGHT = DOW* 44

OUTSIDE

5 5 4
MEDIUM HEAVY REVERSE
MULLION MULLION JAMB
SILICONE SEAL CLOSED CELL
POCKETED FILLER GLAZING WEDGE BACKING ROD
EN9499
HEAVY DUTY FRAME POCKETED FILLER
STANDARD FRAME EN5011 EN9499
EN5010 FULL HEIGHT WITH REVERSE TRANSOMS

GLASS WIDTH = DOW + 18 GLASS WIDTH = DOW + 18


44 DAYLIGHT = DOW* 44 DAYLIGHT = DOW* 44

OUTSIDE
* IF USING END GASKETS - EACH GASKET WHEN ASSEMBLED MEASURES 0.35MM. PLEASE TAKE THIS
INTO CONSIDERATION WHEN DETERMINING HEAD, SILL & TRANSOM CUT LENGTHS.
^ ENTIRE POCKET COMPLETELY SEALED OVER POCKET FILLER WITH SILICONE AT TRANSOMS

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec7 Arrangements - Page 6 01-07-2022 ©


400 Narrowline
Horizontal Arrangements 04, 06 & 08 - Alt. Jambs & Self Mating Mullions Scale 1:2
REFER TO SUB SILL & SUB FRAME TECHNICAL MANUAL FOR SUB FRAME DETAILS

8 6 6
SUB JAMB LIGHT SPLIT PLAIN MULLION
MULLION MATING WITH OTHER PRODUCTS

SUB FRAME BEAD POCKETED FILLER EXRUDED LOUVRE,


EN9499
GLAZING WEDGE PLAIN S/M MULLION
SUB FRAME EP15841 SASHLESS
150mm @ 600 CTRS FROM CTR
BASE CO-EXT EXPANSION JOINT SEAL DOUBLE HUNG OR
SMALL BULB SEAL
300841 316051 OTHER SUITABLE
STANDARD FRAME LIGHT S/M MULLION PRODUCTS
EN5010 EP5408

2
20 GLASS WIDTH = DOW + 18 GLASS WIDTH = DOW + 18 2
MIN
44 DAYLIGHT = DOW* 46 DAYLIGHT = DOW* 46

OUTSIDE

6 6 4
MEDIUM HEAVY DUTY ALT. NARROW
SPLIT MULLION SPLIT MULLION JAMB
NARROW FRAME
SILICONE SEAL POCKET FILLER ^ CO-EXT EXPANSION JOINT SEAL EN5016
BOTTOM 100mm 322026 316051 TYP ANGLE TRIM
LIGHT S/M MULLION AT TRANSOM HEAVY S/M MULLION
EP5408 TRIMMED WHERE REQ. EP5409

2 GLASS WIDTH = DOW + 18 2 GLASS WIDTH = DOW + 18


46 DAYLIGHT = DOW* 46 DAYLIGHT = DOW* 28

OUTSIDE
* IF USING END GASKETS - EACH GASKET WHEN ASSEMBLED MEASURES 0.35MM. PLEASE TAKE THIS
INTO CONSIDERATION WHEN DETERMINING HEAD, SILL & TRANSOM CUT LENGTHS.
^ ENTIRE POCKET COMPLETELY SEALED OVER POCKET FILLER WITH SILICONE AT TRANSOMS

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec7 Arrangements - Page 7


400 Narrowline
Horizontal Arrangement 07 - 90° & 180° Couplers Scale 1:2

7
180° BOX COUPLER

POCKET FILLER ^ GLAZING WEDGE 180° POST SILICONE


322026 NARROW FRAME EP17034 FULL HEIGHT
AT TRANSOM EN5016 STD FRAME
TRIMMED WHERE REQ. EN5010

28 101.6 44

7
90° BOX COUPLER

SILICONE SEAL CLOSED CELL


BACKING ROD
POCKETED FILLER
EP9499
44

150mm @ 600 CTRS STANDARD FRAME


EN5010

90° POST
EP17033
101.6

9 9
GLASS WIDTH = DOW + 18
44 DAYLIGHT = DOW* 44 101.6

^ ENTIRE POCKET COMPLETELY SEALED OVER POCKET FILLER WITH SILICONE AT TRANSOMS

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec7 Arrangements - Page 8 01-07-2022 ©


400 Narrowline
Horizontal Arrangement 07 - 2 / 3 Way Corner Post, Coupler & Mullion Scale 1:2

7
180° CORNER MULLION
GLAZING WEDGE POCKETED FILLER
SILICONE BUTT POCKET FILLER ^ EN9499 FLUSH FILLER 2/3 WAY CORNER
322026 EK5925 EN5014
AT TRANSOM
TRIMMED WHERE REQ.

6 9
101.5

OUTSIDE
7
7
90° CORNER MULLION
FLUSHLINE / NARROWLINE
COUPLER
SILICONE FLAT FILLER
FLUSHLINE / NARROWLINE COUPLER FULL HEIGHT EN5028
EP10536
100mm FLUSHLINE FRAME
E19861 SHOWN AS EXAMPLE
SILICONE
FULL HEIGHT
REFER TO 419 FLUSHLINE MANUAL
FOR FRAME DETAILS STANDARD FRAME
EN5010

OUTSIDE

9
94 101.6

OUTSIDE

^ ENTIRE POCKET COMPLETELY SEALED OVER POCKET FILLER WITH SILICONE AT TRANSOMS

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec7 Arrangements - Page 9


400 Narrowline
Arrangement - Internal Glazed Partition Scale 1:2

SILICONE
FULL HEIGHT

FLAT FILLER
EN5028

28
NARROW FRAME
EN5016

NARROW FRAME HOOK BEAD


EP5447
GLASS HEIGHT = DOH - 12 GLAZING WEDGE
DAYLIGHT = DOH

GLASS SETTING BLOCK

20mm PACKER
28

FLAT FILLER NARROW FRAME


EN5028
EN5016
GLAZING WEDGE

GLASS WIDTH = DOW + 18


28 DAYLIGHT = DOW* 28

INTERNAL GLAZED PARTITION


A SUGGESTED DETAIL FOR LOW PROFILE HEADS, SILLS & JAMBS
FOR INTERIOR USE ONLY.

* IF USING END GASKETS - EACH GASKET WHEN ASSEMBLED MEASURES 0.35MM. PLEASE TAKE THIS
INTO CONSIDERATION WHEN DETERMINING HEAD, SILL & TRANSOM CUT LENGTHS.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec7 Arrangements - Page 10 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: 9962S3A


Performed by: Ian Bennie & Associates Test Laboratory, Victoria – December, 1999
Test Drawing Number: 400-001

Configuration: F.F / F
Glass: 6mm Clear Float
Bead / Glazing: External Bead / Roll in Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

AIR INFILTRATION RESULTS:


0.04L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.04L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN6523 / EN5020 / EN5032 1000Pa Pressure for a period of 15mins
Transom: EN9499 / EN5020 / EN5032

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 1


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: 9962S3B


Performed by: Ian Bennie & Associates Test Laboratory, Victoria – December, 1999
Test Drawing Number: 400-002

Configuration: F.F / F
Glass: 6mm Clear Float
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

WATER PENETRATION RESULTS:


Sill: EN6523 / EN5020 / EN5032 1000Pa Pressure for a period of 15mins
Transom: EN9499 / EN5020 / EN5032

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 2 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-010


Performed by: Capral Mechanical Test Laboratory, Victoria – April, 2011
Test Drawing Number: 31-440

Configuration: F.F
Glass: 10.38mm Laminate
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion Configuration: EN9457 / EN9499 2704Pa 2710Pa
(1735mm Span) (Span/261) (Span/271)

AIR INFILTRATION RESULTS:


0.03L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.08L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN6523 1511Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
5000Pa 5026Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 3


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-010A


Performed by: Capral Mechanical Test Laboratory, Victoria – April, 2011
Test Drawing Number: 31-441

Configuration: F.F
Glass: 10.38mm Laminate
Bead / Glazing: External Bead / Roll in Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion Configuration: EN9457 / EN9499 2508Pa 2530Pa
(1735mm Span) (Span/256) (Span/278)

AIR INFILTRATION RESULTS:


0.04L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.00L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN6523 755Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
3554Pa 3512Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 4 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-012


Performed by: Capral Mechanical Test Laboratory, Victoria – April, 2011
Test Drawing Number: 31-442

Configuration: F.F
Glass: 10.38mm Laminate
Bead / Glazing: External Bead / Roll in Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion Configuration: EN5010 / EN9499 2812Pa 2814Pa
(1764mm Span) (Span/251) (Span/265)

AIR INFILTRATION RESULTS:


0.30L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.10L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN6523 921Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
5029Pa 4211Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 5


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-013


Performed by: Capral Mechanical Test Laboratory, Victoria – April, 2011
Test Drawing Number: 31-445

Configuration: F.F
Glass: 10.38mm Laminate
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion Configuration: EN5011 / EN9499 2907Pa 2918Pa
(1764mm Span) (Span/271) (Span/257)

AIR INFILTRATION RESULTS:


0.21L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.06L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 901Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
4488Pa 4495Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 6 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-019


Performed by: Capral Mechanical Test Laboratory, Victoria – May, 2011
Test Drawing Number: 31-456

Configuration: F.F
Glass: 8mm Toughened
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion: EN5014 / EN9499 / EN9499 / EK5925 4205Pa 4202Pa
(2064mm Span) (Span/287) (Span/258)

AIR INFILTRATION RESULTS:


0.28L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.39L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN6523 1512Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
7241Pa 7518Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 7


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-020


Performed by: Capral Mechanical Test Laboratory, Victoria – May, 2011
Test Drawing Number: 31-458

Configuration: F.F
Glass: 10.38mm Laminate
Bead / Glazing: Internal Bead / Roll in Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion: EP5408 / EP5408 2902Pa 2922Pa
(2064mm Span) (Span/256) (Span/268)

AIR INFILTRATION RESULTS:


0.01L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.00L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN6523 899Pa Pressure for a period of 15mins
(Internal Bead)

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
4572Pa 4564Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 8 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-021


Performed by: Capral Mechanical Test Laboratory, Victoria – May, 2011
Test Drawing Number: 31-459

Configuration: F.F
Glass: 10.38mm Laminate
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion: EP5408 / EP5409 3900Pa 3945Pa
(2020mm Span) (Span/276) (Span/265)

AIR INFILTRATION RESULTS:


0.18L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.19L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN6523 894Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
8606Pa 8677Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 9


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-022


Performed by: Capral Mechanical Test Laboratory, Victoria – May, 2011
Test Drawing Number: 31-460

Configuration: F.F
Glass: 8mm Toughened
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion: EP5409 / EP5409 5255Pa 5249Pa
(2060mm Span) (Span/250) (Span/284)

AIR INFILTRATION RESULTS:


0.47L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.43L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN5693 1508Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
10367Pa 10393Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 10 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-030


Performed by: Capral Mechanical Test Laboratory, Victoria – August, 2011
Test Drawing Number: 31-469

Configuration: F/F
Glass: 8.38mm Laminated
Bead / Glazing: Internal Bead / Captive Wedge (outside) / Roll in Wedge (inside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Transom: EN5032 / EN5021 2763Pa 2744Pa
(1440mm Span) (Span/367) (Span/360)

AIR INFILTRATION RESULTS:


0.00L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.01L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN5693 913Pa Pressure for a period of 15mins
Transom: EN5032 / EN5021

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
2763Pa 3409Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 11


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-031


Performed by: Capral Mechanical Test Laboratory, Victoria – August, 2011
Test Drawing Number: 31-470

Configuration: F/F
Glass: 8.38mm Laminated
Bead / Glazing: Internal Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

AIR INFILTRATION RESULTS:


0.00L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.00L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN5693 1521Pa Pressure for a period of 15mins
Transom: EN5032 / EN5021

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
4242Pa 4255Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 12 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-032


Performed by: Capral Mechanical Test Laboratory, Victoria – August, 2011
Test Drawing Number: 31-471

Configuration: F/F
Glass: 8.38mm Laminated
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Transom: EN5032 / EN5020 / EN9499 3035Pa 3057Pa
(1430mm Span) (Span/366) (Span/386)

AIR INFILTRATION RESULTS:


0.04L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.05L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill: EN5032 / EN5020 / EN5693 1513Pa Pressure for a period of 15mins
Transom: EN5032 / EN5020 / EN9499

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
4901Pa 3057Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 13


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-046


Performed by: Capral Mechanical Test Laboratory, Victoria – November, 2011
Test Drawing Number: 31-504

Configuration: F/F
Glass: 6.38mm Laminated
Bead / Glazing: External Bead / Roll In Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Transom: EN5021 / EN5032 600Pa 606Pa
(2900mm Span) (Span/191) (Span/196)

AIR INFILTRATION RESULTS:


0.01L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.02L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 300Pa Pressure for a period of 15mins
Transom : EN5021 / EN5032

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
855Pa 836Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 14 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-047


Performed by: Capral Mechanical Test Laboratory, Victoria – November, 2011
Test Drawing Number: 31-505

Configuration: F/F
Glass: 6.38mm Laminated
Bead / Glazing: External Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Transom : EN5021 / EN5032 703Pa 712Pa
(2900mm Span) (Span/163) (Span/172)

AIR INFILTRATION RESULTS:


0.01L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.02L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 449Pa Pressure for a period of 15mins
Transom : EN5021 / EN5032

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1217Pa 1217Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 15


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-048


Performed by: Capral Mechanical Test Laboratory, Victoria – November, 2011
Test Drawing Number: 31-508

Configuration: F/F
Glass: 6.38mm Laminated
Bead / Glazing: Internal Bead / Roll In Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Transom : EN5020 / EN9499 / EN5032 695Pa 697Pa
(2930mm Span) (Span/211) (Span/210)

AIR INFILTRATION RESULTS:


0.02L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.03L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 302Pa Pressure for a period of 15mins
Transom : EN5020 / EN9499 / EN5032

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1038Pa 1032Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 16 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-049


Performed by: Capral Mechanical Test Laboratory, Victoria – November, 2011
Test Drawing Number: 31-509

Configuration: F/F
Glass: 6.38mm Laminated
Bead / Glazing: Internal Bead / Silicone Seal

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Transom : EN5020 / EN9499 / EN5032 715Pa 706Pa
(2930mm Span) (Span/198) (Span/215)

AIR INFILTRATION RESULTS:


0.08L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.06L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 463Pa Pressure for a period of 15mins
Transom : EN5020 / EN9499 / EN5032

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1862Pa 1878Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 17


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-052


Performed by: Capral Mechanical Test Laboratory, Victoria – December, 2011
Test Drawing Number: 31-512

Configuration: F.F
Glass: 8.38mm Laminated
Bead / Glazing: External Bead / Roll In Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EP5408 / EP5408 501Pa 501Pa
(2950mm Span) (Span/254) (Span/278)

AIR INFILTRATION RESULTS:


0.04L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.15L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 308Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1126Pa 1113Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 18 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-054


Performed by: Capral Mechanical Test Laboratory, Victoria – December, 2011
Test Drawing Number: 31-514

Configuration: F.F
Glass: 8.38mm Laminated
Bead / Glazing: External Bead / Roll In Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN9457 / EN9499 611Pa 701Pa
(2675mm Span) (Span/167) (Span/167)

AIR INFILTRATION RESULTS:


0.02L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.08L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 301Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1010Pa 1019Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 19


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-055


Performed by: Capral Mechanical Test Laboratory, Victoria – December, 2011
Test Drawing Number: 31-515

Configuration: F.F
Glass: 8.38mm Laminated
Bead / Glazing: External Bead / Roll In Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5010 / EN9499 606Pa 609Pa
(2675mm Span) (Span/154) (Span/164)

AIR INFILTRATION RESULTS:


0.11L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.20L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 303Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1122Pa 1124Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 20 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C011-056


Performed by: Capral Mechanical Test Laboratory, Victoria – December, 2011
Test Drawing Number: 31-516

Configuration: F.F
Glass: 8.38mm Laminated
Bead / Glazing: External Bead / Roll In Wedges

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5011 / EN9499 618Pa 607Pa
(2675mm Span) (Span/196) (Span/221)

AIR INFILTRATION RESULTS:


0.05L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.13L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EN5032 / EN5020 / EN5693 302Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1257Pa 1087Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 21


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-004


Performed by: Capral Mechanical Test Laboratory, Victoria – February, 2013
Test Drawing Number: 31-618

Configuration: F.F
Glass: 8mm Toughened
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5409 / EN5409 4508Pa 4515Pa
(2055mm Span) (Span/302) (Span/288)

AIR INFILTRATION RESULTS:


0.00L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.01L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EP12761 / EN5020 / EN5693 906Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
9246Pa 9272Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 22 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-007


Performed by: Capral Mechanical Test Laboratory, Victoria – February, 2013
Test Drawing Number: 31-623

Configuration: F.F
Glass: 8mm Toughened
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5409 / EN5408 4508Pa 4502Pa
(2055mm Span) (Span/224) (Span/249)

AIR INFILTRATION RESULTS:


0.01L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.17L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EP12761 / EN5020 / EN5693 901Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
7507Pa 7505Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 23


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-008


Performed by: Capral Mechanical Test Laboratory, Victoria – March, 2013
Test Drawing Number: 31-624

Configuration: F.F
Glass: 8mm Toughened
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5408 / EN5408 3015Pa 3013Pa
(2073mm Span) (Span/244) (Span/253)

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
5359Pa 5365Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 24 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-023


Performed by: Capral Mechanical Test Laboratory, Victoria – May, 2013
Test Drawing Number: 31-641

Configuration: F.F
Glass: 10.38mm Laminated
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5011 / EN9499 4006Pa 4013Pa
(1760mm Span) (Span/178) (Span/204)

AIR INFILTRATION RESULTS:


0.07L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.03L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EP12761 / EN5020 / EN5693 895Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
5559Pa 5548Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 25


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-024


Performed by: Capral Mechanical Test Laboratory, Victoria – May, 2013
Test Drawing Number: 31-644

Configuration: F.F
Glass: 10.38mm Laminated
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN5010 / EN9499 3314Pa 3317Pa
(1775mm Span) (Span/202) (Span/221)

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
4905Pa 4905Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 26 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-029


Performed by: Capral Mechanical Test Laboratory, Victoria – June, 2013
Test Drawing Number: 31-647

Configuration: F.F
Glass: 6.38mm Laminated
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EP5408 / EP5408 553Pa 553Pa
(2985mm Span) (Span/255) (Span/243)

AIR INFILTRATION RESULTS:


0.06L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.09L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EP12761 / EN5020 / EN5693 455Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1252Pa 1250Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 27


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-032


Performed by: Capral Mechanical Test Laboratory, Victoria – June, 2013
Test Drawing Number: 31-652

Configuration: F.F
Glass: 10.38mm Laminated
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EN9499 / EN5014 / EN9499 705Pa 703Pa
(3455mm Span) (Span/179) (Span/179)

AIR INFILTRATION RESULTS:


0.75L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.82L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EP12761 / EN5020 / EN5693 458Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1208Pa 1212Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 28 01-07-2022 ©


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-033


Performed by: Capral Mechanical Test Laboratory, Victoria – July, 2013
Test Drawing Number: 31-651

Configuration: F.F
Glass: 10.38mm Laminated
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EP5409 / EP5409 697Pa 697Pa
(3455mm Span) (Span/228) (Span/232)

AIR INFILTRATION RESULTS:


0.76L/s.m2 @ 75Pa Positive Test Pressure Achieved Air Conditioned Rating
0.71L/s.m2 @ 75Pa Negative Test Pressure

WATER PENETRATION RESULTS:


Sill : EP12761 / EN5020 / EN5693 450Pa Pressure for a period of 15mins

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1483Pa 1475Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 29


400 Narrowline
Test Report Summary

STRUCTURAL & WATER - TEST REPORT NUMBER: C013-034


Performed by: Capral Mechanical Test Laboratory, Victoria – July, 2013
Test Drawing Number: 31-653

Configuration: F.F
Glass: 10.38mm Laminated
Bead / Glazing: External Bead / Captive Wedge (inside) / Roll in Wedge (outside)

Approved to Standard: AS4420-1996 (as called up by AS2047-1999)

DEFLECTION TEST RESULTS:


+ Test Pressure - Test Pressure
Mullion : EP5409 / EP5408 437Pa 437Pa
(3455mm Span) (Span/287) (Span/294)

ULTIMATE STRENGTH RESULTS:


+ Test Pressure - Test Pressure
1164Pa 1162Pa

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 30 01-07-2022 ©


400 Narrowline
Test Report Summary
BAL 40 BUSHFIRE TESTING - TEST REPORT NUMBER: 44400500.1
- ASSESSMENT REPORT: 52627900.1a
Performed by: Exova Warringtonfire, Victoria – March, 2017
Test Drawing Number: 31-920

Captive Wedge: Co-Extruded Captive Wedge – 315788


Glazing Wedge: 300013

Approved to Standard: AS1530.8.1 – 2018


Reference 16.9.2(b) of AS1530.8.1 – 2018: “Where single glazing is tested, the glazing may be the same or thicker glazing of the same
type and the glazing may be multiple glazing where the fire side pane is the same or thicker than tested.”

TEST RESULTS:
Performance Criteria Time to Failure (min) Position of Failure
Formation of through-gaps greater than 3mm. No Failure -
Sustained failure for 10sec. on the non-fire side. No Failure -
Flaming on the fire –exposed side at the end of the 60min.
No Failure -
test period.
Radiant heat flux 365mm from the non-fire exposed side
No Failure -
exceeding 15kW/m2.
Mean and maximum temperature rises greater than 140K & No applicable for glazed
-
180K. elements.
Radiant heat flux 250mm from the specimen, greater than
No Failure -
3kW/m2 between 20mins. and 60mins.
Mean and maximum temperature of internal faces
Not applicable for glazed
exceeding 250ºC and 300ºC respectively between 20mins. -
elements.
and 60mins. after commencement of test.
Crib Class A Peak Heat Flux 40 kW/m2
Test Result BAL-A40
Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-12-2017
01-07-2022 Sec8 Testing - Page 31
400 Narrowline
Test Report Summary

ACOUSTIC
Performed by: Australian Hearing National Acoustic Laboratories, New South Wales – October, 2001

Configuration: F.F / F

Approved to Standard: AS1191-2002

TEST REPORT NUMBER: ATF1152


Test Drawing Number: TA400-001

TEST SAMPLE DETAILS:


Glass: 6.38mm Laminated Glass
Glazing Wedge: M027142 (300013) 5mm Gap Glazing Wedge
Backing Seal: M027403 (300841) Small Bulb Seal

SOUND TRANSMISSION CLASS:


STC: 32

SOUND INSULATION RATING:


Rw (C;Ctr): 32 (-1; -2)

TEST REPORT NUMBER: ATF1153


Test Drawing Number: TA400-002

TEST SAMPLE DETAILS:


Glass: 10.38mm Laminated Glass
Glazing Wedge: M027101 (300001) 3mm Gap Glazing Wedge
Backing Seal: M027403 (300841) Small Bulb Seal

SOUND TRANSMISSION CLASS:


STC: 34

SOUND INSULATION RATING:


Rw (C;Ctr): 34 (-1; -2)

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec8 Testing - Page 32 01-07-2022 ©


400 Narrowline
Test Report Summary

ACOUSTIC
Performed by: Australian Hearing National Acoustic Laboratories, New South Wales – October, 2012

Configuration: F.F

Approved to Standard: AS1191-2002

TEST REPORT NUMBER: 4870-25


Test Drawing Number: 31-595

TEST SAMPLE DETAILS:


Glass: 6.5mm Hush Laminated
Glazing Wedge: 300013 5mm Gap Glazing Wedge; 315788 5mm Gap Captive Wedge
Frame Seal: 316051 Mullion Seal

SOUND INSULATION RATING:


Rw (C;Ctr): 34 (-0; -3)

TEST REPORT NUMBER: 4870-16


Test Drawing Number: 31-595

TEST SAMPLE DETAILS:


Glass: 10.5mm Hush Laminated
Glazing Wedge: 300001 3mm Gap Glazing Wedge; 315787 3mm Gap Captive Wedge
Frame Seal: 316051 Mullion Seal

SOUND INSULATION RATING:


Rw (C;Ctr): 37 (-0; -3)

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-07-2022 Sec8 Testing - Page 33


400 Narrowline
Span Table
LIGHT MULLION - EN9457 / EN9499

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4000Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 0.966 0.657 0.507 0.421 - - -
3000
U 2.344 1.589 1.221 1.009 - - -
S (L/250) 1.071 0.730 0.564 0.470 0.412 - -
2900
U 2.510 1.704 1.312 1.087 0.946 - -
S (L/250) 1.191 0.813 0.630 0.527 0.463 0.424 0.402
2800
U 2.696 1.833 1.414 1.174 1.026 0.933 0.879
S (L/250) 1.331 0.910 0.707 0.593 0.524 0.482 0.460
2700
U 2.903 1.976 1.528 1.273 1.117 1.022 0.969
S (L/250) 1.493 1.022 0.797 0.671 0.596 0.552 0.531
2600
U 3.134 2.138 1.657 1.385 1.221 1.124 1.075 *
S (L/250) 1.682 1.155 0.903 0.763 0.682 0.636 0.617
2500
U 3.395 2.320 1.803 1.514 1.342 1.244 * 1.202 *
S (L/250) 1.905 1.311 1.029 0.874 0.786 0.740 0.726
2400
U 3.690 2.527 1.971 1.662 1.482 1.386 * 1.355 *
S (L/250) 2.169 1.497 1.180 1.008 0.914 0.868 0.860
2300
U 4.025 2.764 2.163 1.834 1.648 1.557 * 1.539 *
S (L/250) 2.485 1.721 1.363 1.172 1.072 1.030 1.028 *
2200
U 4.409 3.036 2.387 2.035 1.845 1.764 * 1.759 *
S (L/250) 2.865 1.992 1.587 1.375 1.270 * 1.238 * 1.238 *
2100
U 4.851 3.351 2.648 2.274 2.083 * 2.022 * 2.022 *
S (L/250) 3.328 2.324 1.863 1.630 1.524 * 1.505 * 1.505 *
2000
U 5.364 3.720 2.956 2.561 2.376 * 2.341 * 2.341 *
S (L/250) 3.897 2.736 2.210 1.954 1.854 * 1.847 * 1.847 *
1900
U 5.500 4.154 3.324 2.911 * 2.742 * 2.731 * 2.731 *
S (L/250) 4.000 3.252 2.652 2.375 2.293 * 2.293 * 2.293 *
1800
U 5.500 4.671 * 3.770 * 3.343 * 3.212 * 3.212 * 3.212 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 1
400 Narrowline
Span Table
MEDIUM MULLION - EN5010 / EN9499

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4000Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 0.804 0.545 0.419 - - - -
3300
U 2.150 1.454 1.112 - - - -
S (L/250) 0.904 0.614 0.472 - - - -
3175
U 2.325 1.574 1.206 - - - -
S (L/250) 1.021 0.694 0.535 0.444 - - -
3050
U 2.522 1.709 1.312 1.083 - - -
S (L/250) 1.159 0.789 0.610 0.508 0.445 0.405 -
2925
U 2.745 1.863 1.434 1.187 1.033 0.934 -
S (L/250) 1.324 0.903 0.700 0.585 0.515 0.471 0.446
2800
U 3.000 2.040 1.573 1.307 1.142 1.039 0.978
S (L/250) 1.521 1.040 0.809 0.679 0.601 0.554 0.529
2675
U 3.292 2.242 1.735 1.446 1.271 1.164 * 1.106 *
S (L/250) 1.759 1.206 0.942 0.794 0.707 0.658 0.635
2550
U 3.629 2.477 1.923 1.610 1.424 1.315 * 1.263 *
S (L/250) 2.050 1.410 1.106 0.938 0.842 0.791 0.773
2425
U 4.020 2.752 2.144 1.806 1.608 1.500 * 1.462 *
S (L/250) 2.409 1.663 1.311 1.120 1.015 0.965 0.956 *
2300
U 4.479 3.076 2.407 2.040 1.834 1.732 * 1.713 *
S (L/250) 2.858 1.981 1.572 1.354 1.241 1.197 * 1.195 *
2175
U 5.023 3.461 2.724 2.327 2.115 * 2.029 * 2.026 *
S (L/250) 3.427 2.388 1.908 1.661 1.543 1.514 * 1.514 *
2050
U 5.500 3.926 3.111 2.683 2.472 * 2.419 * 2.419 *
S (L/250) 4.000 2.915 2.350 2.072 1.958 * 1.947 * 1.947 *
1925
U 5.500 4.494 3.590 3.134 * 2.940 * 2.922 * 2.922 *
S (L/250) 4.000 3.613 2.946 2.638 2.547 * 2.547 * 2.547 *
1800
U 5.500 5.198 * 4.195 * 3.720 * 3.574 * 3.574 * 3.574 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 2 14-06-2016


01-07-2022 ©
400 Narrowline
Span Table
HEAVY MULLION - EN5011 / EN9499

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4000Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 0.756 0.511 - - - - -
3500
U 2.142 1.446 - - - - -
S (L/250) 0.844 0.572 0.438 - - - -
3375
U 2.305 1.557 1.191 - - - -
S (L/250) 0.946 0.642 0.493 0.407 - - -
3250
U 2.488 1.683 1.288 1.059 - - -
S (L/250) 1.065 0.723 0.557 0.461 0.401 - -
3125
U 2.693 1.824 1.399 1.153 0.997 - -
S (L/250) 1.205 0.820 0.633 0.526 0.459 0.417 -
3000
U 2.926 1.984 1.525 1.260 1.093 0.986 -
S (L/250) 1.372 0.935 0.723 0.603 0.529 0.483 0.455
2875
U 3.189 2.166 1.668 1.383 1.205 1.092 * 1.024 *
S (L/250) 1.570 1.072 0.832 0.696 0.614 0.564 0.536
2750
U 3.491 2.375 1.834 1.525 1.336 1.218 * 1.151 *
S (L/250) 1.808 1.238 0.964 0.811 0.719 0.665 0.638
2625
U 3.837 2.616 2.026 1.692 1.490 1.369 * 1.307 *
S (L/250) 2.098 1.440 1.126 0.952 0.850 0.794 0.770
2500
U 4.238 2.896 2.251 1.889 1.675 1.553 * 1.500 *
S (L/250) 2.453 1.690 1.328 1.129 1.017 0.960 0.944
2375
U 4.706 3.225 2.517 2.125 1.899 1.780 * 1.745 *
S (L/250) 2.894 2.001 1.581 1.355 1.233 1.178 * 1.172 *
2250
U 5.256 3.614 2.835 2.410 2.174 * 2.066 * 2.053 *
S (L/250) 3.447 2.394 1.904 1.647 1.517 1.473 * 1.473 *
2125
U 5.500 4.079 3.219 2.760 2.521 * 2.437 * 2.437 *
S (L/250) 4.000 2.899 2.324 2.033 1.900 1.877 * 1.877 *
2000
U 5.500 4.643 * 3.690 * 3.198 * 2.966 * 2.923 * 2.923 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 3
400 Narrowline
Span Table
LIGHT SPLIT MULLION - EP5408 / EP5408

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4000Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 0.981 0.664 0.508 0.418 - - -
3500
U 2.715 1.833 1.399 1.146 - - -
S (L/250) 1.095 0.742 0.569 0.469 0.405 - -
3375
U 2.922 1.974 1.509 1.238 1.065 - -
S (L/250) 1.227 0.832 0.640 0.528 0.458 0.412 -
3250
U 3.154 2.133 1.633 1.343 1.158 1.035 -
S (L/250) 1.382 0.939 0.723 0.599 0.521 0.470 0.438
3125
U 3.414 2.312 1.773 1.461 1.264 1.134 * 1.049 *
S (L/250) 1.564 1.064 0.821 0.682 0.596 0.541 0.506
3000
U 3.709 2.515 1.933 1.597 1.386 1.250 * 1.163 *
S (L/250) 1.780 1.213 0.939 0.782 0.686 0.626 0.590
2875
U 4.043 2.746 2.115 1.753 1.528 1.385 * 1.298 *
S (L/250) 2.037 1.391 1.080 0.904 0.797 0.732 0.695
2750
U 4.425 3.011 2.325 1.934 1.693 1.544 * 1.459 *
S (L/250) 2.346 1.606 1.251 1.052 0.933 0.863 0.828
2625
U 4.864 3.316 2.569 2.145 1.889 1.736 * 1.656 *
S (L/250) 2.722 1.869 1.461 1.235 1.104 1.030 0.999
2500
U 5.373 3.672 2.854 2.395 2.123 * 1.969 * 1.902 *
S (L/250) 3.183 2.192 1.722 1.465 1.320 1.245 * 1.225 *
2375
U 5.500 4.088 3.191 2.694 2.407 * 2.256 * 2.213 *
S (L/250) 3.754 2.596 2.051 1.758 1.599 1.529 * 1.520 *
2250
U 5.500 4.581 3.593 3.055 * 2.757 * 2.619 * 2.602 *
S (L/250) 4.000 3.106 2.471 2.137 1.968 * 1.911 * 1.911 *
2125
U 5.500 5.171 * 4.080 * 3.498 * 3.195 * 3.090 * 3.089 *
S (L/250) 4.000 3.762 3.016 2.638 2.466 * 2.435 * 2.435 *
2000
U 5.500 5.500 * 4.678 * 4.053 * 3.760 * 3.705 * 3.705 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 4 14-06-2016


01-07-2022 ©
400 Narrowline
Span Table
MEDIUM SPLIT MULLION - EP5408 / EP5409

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4500Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.086 0.733 0.559 0.458 - - -
3800
U 2.990 2.014 1.533 1.251 - - -
S (L/250) 1.226 0.829 0.633 0.520 0.447 - -
3650
U 3.243 2.187 1.667 1.362 1.166 - -
S (L/250) 1.392 0.942 0.721 0.593 0.511 0.456 0.419
3500
U 3.529 2.382 1.819 1.489 1.278 1.135 * 1.036 *
S (L/250) 1.589 1.077 0.826 0.681 0.589 0.528 0.487
3350
U 3.856 2.606 1.993 1.635 1.407 1.254 * 1.151 *
S (L/250) 1.825 1.239 0.953 0.788 0.684 0.616 0.571
3200
U 4.230 2.863 2.193 1.804 1.558 1.395 * 1.286 *
S (L/250) 2.111 1.435 1.107 0.918 0.800 0.725 0.677
3050
U 4.662 3.160 2.426 2.002 1.736 1.562 * 1.450 *
S (L/250) 2.460 1.676 1.296 1.080 0.946 0.862 0.812
2900
U 5.164 3.506 2.699 2.236 1.947 * 1.763 * 1.649 *
S (L/250) 2.890 1.974 1.532 1.282 1.131 1.038 0.987
2750
U 5.752 3.914 3.022 2.514 2.201 * 2.008 * 1.897 *
S (L/250) 3.428 2.348 1.830 1.540 1.368 1.268 * 1.219 *
2600
U 6.447 4.398 3.409 2.849 * 2.512 * 2.312 * 2.211 *
S (L/250) 4.108 2.824 2.212 1.875 1.680 1.574 * 1.535 *
2450
U 7.278 4.979 * 3.876 * 3.260 * 2.899 * 2.699 * 2.622 *
S (L/250) 4.500 3.439 2.711 2.316 2.098 * 1.994 * 1.976 *
2300
U 8.281 5.685 * 4.450 * 3.772 * 3.390 * 3.202 * 3.167 *
S (L/250) 4.500 4.248 3.374 2.913 * 2.675 * 2.589 * 2.587 *
2150
U 8.600 * 6.557 * 5.167 * 4.422 * 4.028 * 3.880 * 3.877 *
S (L/250) 4.500 4.500 * 4.280 * 3.744 * 3.499 * 3.455 * 3.455 *
2000
U 8.600 * 7.652 * 6.081 * 5.269 * 4.887 * 4.816 * 4.816 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 5
400 Narrowline
Span Table
HEAVY SPLIT MULLION - EP5409 / EP5409

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 5200Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.204 0.812 0.619 0.505 0.432 - -
4000
U 3.492 2.350 1.787 1.455 1.239 - -
S (L/250) 1.352 0.912 0.696 0.569 0.488 0.432 -
3850
U 3.772 2.540 1.933 1.576 1.345 1.187 * -
S (L/250) 1.524 1.030 0.787 0.645 0.554 0.492 0.449
3700
U 4.086 2.755 2.099 1.714 1.466 1.297 * 1.178 *
S (L/250) 1.727 1.168 0.894 0.734 0.632 0.564 0.517
3550
U 4.442 2.998 2.287 1.871 1.604 1.423 * 1.298 *
S (L/250) 1.968 1.333 1.022 0.842 0.727 0.651 0.599
3400
U 4.847 3.274 2.502 2.052 1.764 1.570 * 1.438 *
S (L/250) 2.256 1.530 1.176 0.971 0.842 0.757 0.701
3250
U 5.310 3.592 2.750 2.261 1.949 * 1.743 * 1.604 *
S (L/250) 2.603 1.769 1.362 1.129 0.983 0.888 0.828
3100
U 5.843 * 3.958 3.037 2.504 2.167 * 1.946 * 1.803 *
S (L/250) 3.025 2.060 1.591 1.324 1.158 1.053 0.988
2950
U 6.461 * 4.384 3.372 2.789 * 2.425 * 2.191 * 2.044 *
S (L/250) 3.545 2.419 1.875 1.567 1.378 1.262 * 1.195 *
2800
U 7.183 * 4.884 * 3.767 * 3.129 * 2.734 * 2.487 * 2.342 *
S (L/250) 4.190 2.867 2.232 1.874 1.661 1.534 * 1.468 *
2650
U 8.034 * 5.475 * 4.238 * 3.536 * 3.111 * 2.853 * 2.717 *
S (L/250) 5.003 3.435 2.686 2.271 2.028 * 1.893 * 1.837 *
2500
U 9.046 * 6.182 * 4.805 * 4.033 * 3.575 * 3.315 * 3.202 *
S (L/250) 5.200 4.165 3.276 2.791 * 2.518 * 2.382 * 2.348 *
2350
U 10.264 * 7.038 * 5.499 * 4.648 * 4.161 * 3.910 * 3.846 *
S (L/250) 5.200 5.119 * 4.055 * 3.488 * 3.188 * 3.065 * 3.057 *
2200
U 10.300 * 8.089 * 6.359 * 5.423 * 4.916 * 4.701 * 4.687 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 6 14-06-2016


01-07-2022 ©
400 Narrowline
Span Table
180° BOX COUPLER - EN5010 / EP17034 / EN5010

Note:
Serviceability pressures have been limited to a maximum pressure of
4500Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.891 1.276 0.974 0.798 0.684 0.607 0.553
3800
U 5.815 * 3.918 2.983 2.433 2.078 * 1.834 * 1.663 *
S (L/250) 2.135 1.443 1.103 0.905 0.778 0.692 0.633
3650
U 6.307 * 4.253 * 3.242 2.649 2.267 * 2.007 * 1.826 *
S (L/250) 2.424 1.640 1.256 1.033 0.890 0.795 0.730
3500
U 6.865 * 4.634 * 3.537 * 2.896 * 2.485 * 2.207 * 2.015 *
S (L/250) 2.767 1.875 1.439 1.186 1.026 0.919 0.848
3350
U 7.500 * 5.069 * 3.876 * 3.181 * 2.737 * 2.440 * 2.238 *
S (L/250) 3.179 2.157 1.659 1.372 1.191 1.072 0.995
3200
U 7.500 * 5.568 * 4.266 * 3.510 * 3.030 * 2.713 * 2.502 *
S (L/250) 3.677 2.500 1.927 1.599 1.394 1.262 * 1.179 *
3050
U 7.500 * 6.146 * 4.719 * 3.895 * 3.376 * 3.038 * 2.820 *
S (L/250) 4.284 2.919 2.258 1.880 1.648 1.502 * 1.413 *
2900
U 7.500 * 6.820 * 5.250 * 4.348 * 3.787 * 3.428 * 3.208 *
S (L/250) 4.500 3.438 2.669 2.233 1.969 * 1.808 * 1.718 *
2750
U 7.500 * 7.500 * 5.879 * 4.889 * 4.282 * 3.905 * 3.690 *
S (L/250) 4.500 4.089 3.188 2.683 2.383 * 2.208 * 2.123 *
2600
U 7.500 * 7.500 * 6.630 * 5.542 * 4.887 * 4.498 * 4.301 *
S (L/250) 4.500 4.500 * 3.853 * 3.265 * 2.925 * 2.742 * 2.674 *
2450
U 7.500 * 7.500 * 7.500 * 6.342 * 5.639 * 5.249 * 5.099 *
S (L/250) 4.500 4.500 * 4.500 * 4.034 * 3.654 * 3.473 * 3.441 *
2300
U 7.500 * 7.500 * 7.500 * 7.337 * 6.593 * 6.228 * 6.160 *
S (L/250) 4.500 4.500 * 4.500 * 4.500 * 4.500 * 4.500 * 4.500 *
2150
U 7.500 * 7.500 * 7.500 * 7.500 * 7.500 * 7.500 * 7.500 *
S (L/250) 4.500 4.500 * 4.500 * 4.500 * 4.500 * 4.500 * 4.500 *
2000
U 7.500 * 7.500 * 7.500 * 7.500 * 7.500 * 7.500 * 7.500 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on theoretical section properties only, not on on approved AS2047 testing data.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 01-11-2017
01-07-2022 Sec9 Span Tables - Page 7
400 Narrowline
Span Table
90° BOX COUPLER - EN5010 / EP17033 / EN5010

Note:
Serviceability pressures have been limited to a maximum pressure of
4500Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.573 1.062 0.811 0.664 0.569 0.505 0.460
3800
U 4.225 2.846 2.167 1.768 1.509 1.333 1.208 *
S (L/250) 1.776 1.200 0.918 0.753 0.647 0.576 0.526
3650
U 4.583 3.090 2.355 1.925 1.647 1.458 1.326 *
S (L/250) 2.017 1.364 1.045 0.859 0.741 0.661 0.607
3500
U 4.988 3.367 2.570 2.104 1.805 * 1.604 * 1.464 *
S (L/250) 2.302 1.560 1.197 0.987 0.853 0.765 0.706
3350
U 5.449 3.683 2.816 2.311 1.988 * 1.772 * 1.626 *
S (L/250) 2.645 1.795 1.380 1.141 0.991 0.892 0.828 *
3200
U 5.978 * 4.046 3.099 2.550 2.202 * 1.971 * 1.818 *
S (L/250) 3.059 2.079 1.604 1.330 1.160 1.050 0.981 *
3050
U 6.589 * 4.465 3.429 * 2.830 * 2.453 * 2.207 * 2.049 *
S (L/250) 3.564 2.428 1.878 1.564 1.371 1.249 * 1.176 *
2900
U 7.298 * 4.955 3.815 * 3.159 * 2.751 * 2.491 * 2.331 *
S (L/250) 4.188 2.860 2.220 1.858 1.638 1.504 * 1.429 *
2750
U 7.500 * 5.531 4.271 * 3.552 * 3.111 * 2.837 * 2.681 *
S (L/250) 4.500 3.402 2.652 2.232 1.982 * 1.837 * 1.766 *
2600
U 7.500 * 6.215 * 4.817 * 4.027 * 3.551 * 3.268 * 3.125 *
S (L/250) 4.500 4.091 3.205 2.716 2.434 * 2.281 * 2.224 *
2450
U 7.500 * 7.036 * 5.478 * 4.607 * 4.097 * 3.814 * 3.705 *
S (L/250) 4.500 4.500 * 3.927 * 3.356 * 3.040 * 2.890 * 2.863 *
2300
U 7.500 * 7.500 * 6.289 * 5.330 * 4.790 * 4.525 * 4.475 *
S (L/250) 4.500 4.500 * 4.500 * 4.221 * 3.877 * 3.751 * 3.749 *
2150
U 7.500 * 7.500 * 7.302 * 6.249 * 5.693 * 5.483 * 5.479 *
S (L/250) 4.500 4.500 * 4.500 * 4.500 * 4.500 * 4.500 * 4.500 *
2000
U 7.500 * 7.500 * 7.500 * 7.446 * 6.906 * 6.806 * 6.806 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on theoretical section properties only, not on approved AS2047 testing data.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 8 01-11-2017


01-07-2022 ©
400 Narrowline
Span Table
CORNER MULLION - EN9499 / EN5014 / EN9499

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4500Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.088 0.734 0.560 0.459 - - -
3800
U 3.233 2.178 1.658 1.353 - - -
S (L/250) 1.228 0.830 0.635 0.521 0.447 - -
3650
U 3.507 2.365 1.802 1.473 1.261 - -
S (L/250) 1.394 0.943 0.723 0.594 0.512 0.457 0.420
3500
U 3.817 2.576 1.967 1.610 1.382 1.227 * 1.120 *
S (L/250) 1.592 1.079 0.828 0.682 0.590 0.529 0.488
3350
U 4.170 2.818 2.155 1.768 1.522 1.356 * 1.244 *
S (L/250) 1.829 1.241 0.954 0.789 0.685 0.617 0.572
3200
U 4.575 3.096 2.372 1.951 1.685 1.508 * 1.391 *
S (L/250) 2.115 1.438 1.109 0.920 0.802 0.726 0.678
3050
U 5.042 3.417 2.624 2.165 1.877 1.689 * 1.568 *
S (L/250) 2.464 1.679 1.299 1.082 0.948 0.864 0.813
2900
U 5.585 * 3.792 2.919 2.418 2.105 * 1.906 * 1.783 *
S (L/250) 2.896 1.978 1.535 1.285 1.133 1.040 0.988
2750
U 6.221 * 4.232 3.268 2.718 2.381 * 2.171 * 2.051 *
S (L/250) 3.434 2.352 1.834 1.543 1.371 1.270 * 1.221 *
2600
U 6.972 * 4.756 * 3.686 * 3.081 * 2.717 * 2.500 * 2.391 *
S (L/250) 4.116 2.829 2.216 1.878 1.683 1.577 * 1.538 *
2450
U 7.500 * 5.384 * 4.192 * 3.526 * 3.135 * 2.918 * 2.835 *
S (L/250) 4.500 3.445 2.716 2.320 2.102 * 1.998 * 1.979 *
2300
U 7.500 * 6.148 * 4.813 * 4.079 * 3.666 * 3.463 * 3.425 *
S (L/250) 4.500 4.256 3.380 2.918 * 2.680 * 2.594 * 2.592 *
2150
U 7.500 * 7.091 * 5.588 * 4.782 * 4.356 * 4.196 * 4.193 *
S (L/250) 4.500 4.500 * 4.288 * 3.750 * 3.505 * 3.462 * 3.462 *
2000
U 7.500 * 7.500 * 6.576 * 5.698 * 5.285 * 5.208 * 5.208 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 9
400 Narrowline
Span Table
PLAIN MULLION - EP15841 / EP15841

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4000Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 0.966 0.654 0.501 0.412 - - -
3500
U 2.665 1.799 1.373 1.125 - - -
S (L/250) 1.079 0.731 0.561 0.462 - - -
3375
U 2.869 1.938 1.482 1.215 - - -
S (L/250) 1.209 0.820 0.630 0.521 0.451 0.406 -
3250
U 3.096 2.094 1.603 1.318 1.137 1.016 -
S (L/250) 1.362 0.925 0.712 0.590 0.513 0.463 0.431
3125
U 3.352 2.270 1.741 1.434 1.241 1.114 1.030
S (L/250) 1.541 1.048 0.809 0.672 0.587 0.533 0.499
3000
U 3.641 2.469 1.897 1.568 1.361 1.227 1.142
S (L/250) 1.753 1.195 0.925 0.771 0.676 0.617 0.582
2875
U 3.969 2.696 2.076 1.721 1.500 1.359 1.274
S (L/250) 2.007 1.371 1.064 0.890 0.785 0.721 0.685
2750
U 4.344 2.956 2.283 1.898 1.663 1.516 1.433
S (L/250) 2.312 1.583 1.233 1.036 0.919 0.851 0.816
2625
U 4.775 3.256 2.522 2.106 1.855 1.704 1.626
S (L/250) 2.682 1.841 1.440 1.217 1.087 1.015 0.985
2500
U 5.274 3.604 2.802 2.351 2.085 1.933 1.867
S (L/250) 3.136 2.160 1.697 1.444 1.300 1.227 1.207
2375
U 5.500 4.013 3.133 2.644 2.363 2.215 2.172
S (L/250) 3.699 2.558 2.021 1.732 1.576 1.506 1.498
2250
U 5.500 4.498 3.528 2.999 2.706 2.571 2.555
S (L/250) 4.000 3.060 2.434 2.106 1.939 1.883 1.883
2125
U 5.500 5.077 4.006 3.434 3.137 3.033 3.032
S (L/250) 4.000 3.706 2.972 2.599 2.430 2.399 2.399
2000
U 5.500 5.500 4.593 3.979 3.691 3.637 3.637
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on theoretical section properties, not on approved tests as specified by AS2047.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 10 14-06-2016


01-07-2022 ©
400 Narrowline
Span Table
LIGHT PLAIN / POCKET MULLION - EP15841 / EP5408

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4000Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.087 0.736 0.565 0.465 0.402 - -
3500
U 2.890 1.953 1.493 1.224 1.053 - -
S (L/250) 1.218 0.826 0.635 0.524 0.455 0.409 -
3375
U 3.119 2.110 1.615 1.328 1.145 1.024 -
S (L/250) 1.372 0.932 0.718 0.594 0.517 0.467 0.434
3250
U 3.377 2.287 1.754 1.445 1.250 1.122 * 1.038 *
S (L/250) 1.553 1.056 0.815 0.677 0.591 0.537 0.502
3125
U 3.668 2.487 1.912 1.579 1.371 1.236 * 1.150 *
S (L/250) 1.767 1.204 0.932 0.777 0.681 0.622 0.586
3000
U 3.999 2.716 2.092 1.734 1.511 1.369 * 1.283 *
S (L/250) 2.022 1.381 1.072 0.897 0.791 0.726 0.690
2875
U 4.377 2.978 2.300 1.913 1.675 1.528 * 1.443 *
S (L/250) 2.329 1.595 1.242 1.044 0.926 0.857 0.822
2750
U 4.811 3.280 2.541 2.122 1.869 1.717 * 1.638 *
S (L/250) 2.702 1.855 1.451 1.226 1.095 1.023 0.992
2625
U 5.314 3.631 2.823 2.369 2.100 * 1.947 * 1.881 *
S (L/250) 3.159 2.176 1.710 1.455 1.310 1.236 * 1.216 *
2500
U 5.500 * 4.043 3.156 2.664 2.381 * 2.231 * 2.188 *
S (L/250) 3.727 2.577 2.036 1.745 1.588 1.517 * 1.509 *
2375
U 5.500 * 4.531 * 3.554 3.021 * 2.726 * 2.591 * 2.574 *
S (L/250) 4.000 3.083 2.452 2.121 1.953 * 1.897 * 1.897 *
2250
U 5.500 * 5.115 * 4.036 * 3.460 * 3.160 * 3.056 * 3.055 *
S (L/250) 4.000 3.734 2.994 2.619 2.448 * 2.417 * 2.417 *
2125
U 5.500 * 5.500 * 4.627 * 4.009 * 3.718 * 3.664 * 3.664 *
S (L/250) 4.000 4.000 4.000 * 3.750 * 3.505 * 3.462 * 3.462 *
2000
U 5.500 * 5.500 * 5.500 * 5.500 * 5.285 * 5.208 * 5.208 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on theoretical section properties, not on approved tests as specified by AS2047.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 11
400 Narrowline
Span Table
HEAVY PLAIN / POCKET MULLION - EP15841 / EP5409

Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 4500Pa.

Serviceability pressures have not been limited by water performance.


Where water performance is necessary, refer to Product Specifications
page.

* Indicates the "Braced Bead" (EP12761) should be used.

Mullion Height (mm) Maximum Design Pressure (kPa)


S (L/250) 1.080 0.729 0.557 0.456 - - -
3800
U 2.974 2.004 1.525 1.244 - - -
S (L/250) 1.220 0.824 0.630 0.517 0.444 - -
3650
U 3.226 2.175 1.658 1.355 1.160 - -
S (L/250) 1.385 0.937 0.717 0.590 0.508 0.454 0.417
3500
U 3.511 2.370 1.809 1.481 1.271 1.129 * 1.031 *
S (L/250) 1.581 1.071 0.822 0.677 0.586 0.525 0.484
3350
U 3.836 2.592 1.982 1.627 1.400 1.248 * 1.145 *
S (L/250) 1.816 1.232 0.948 0.783 0.680 0.612 0.568
3200
U 4.208 2.848 2.182 1.795 1.550 1.387 * 1.280 *
S (L/250) 2.100 1.428 1.101 0.913 0.796 0.721 0.673
3050
U 4.638 3.143 2.414 1.992 1.727 1.554 * 1.442 *
S (L/250) 2.447 1.667 1.290 1.074 0.941 0.858 0.807
2900
U 5.137 3.488 2.685 2.224 1.937 * 1.753 * 1.641 *
S (L/250) 2.875 1.964 1.524 1.276 1.125 1.033 0.981
2750
U 5.722 * 3.893 3.007 2.501 2.190 * 1.997 * 1.887 *
S (L/250) 3.410 2.336 1.821 1.532 1.361 1.261 * 1.213 *
2600
U 6.414 * 4.375 3.391 2.835 * 2.499 * 2.300 * 2.200 *
S (L/250) 4.087 2.809 2.201 1.865 1.671 1.566 * 1.527 *
2450
U 7.240 * 4.953 * 3.856 * 3.243 * 2.884 * 2.685 * 2.608 *
S (L/250) 4.500 3.421 2.696 2.304 2.087 * 1.984 * 1.965 *
2300
U 8.238 * 5.656 * 4.427 * 3.752 * 3.372 * 3.185 * 3.150 *
S (L/250) 4.500 4.226 3.357 2.898 * 2.662 * 2.576 * 2.574 *
2150
U 8.600 * 6.523 * 5.141 * 4.399 * 4.007 * 3.860 * 3.857 *
S (L/250) 4.500 4.500 * 4.258 * 3.724 * 3.481 * 3.437 * 3.437 *
2000
U 8.600 * 7.612 * 6.050 * 5.242 * 4.862 * 4.791 * 4.791 *
Mullion Spacing (mm) 600 900 1200 1500 1800 2100 2400

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on theoretical section properties, not on approved tests as specified by AS2047.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 12 14-06-2016


01-07-2022 ©
400 Narrowline
Span Table
TUBULAR TRANSOM - EN5021
Note:
Serviceability pressures have been limited to a maximum
Serviceability Pressure of 3000Pa.
Serviceability pressures have not been limited by water
performance. Where water performance is necessary, refer to
Product Specifications page.
As lowlight mullions under transom are assumed, no
consideration has been given to the deadload component of
loading.

* Indicates the "Braced Bead" (EP12761) should be used.

Transom Spacing
Maximum Design Pressure (kPa)
(mm)
S (L/250) 3.000 * 1.980 1.226 0.817 0.574 0.420 -
1500
U 3.618 * 2.347 * 1.670 * 1.258 0.987 0.797 -
S (L/250) 3.000 * 2.016 1.259 0.844 0.595 0.437 -
1425
U 3.631 * 2.394 * 1.719 * 1.302 1.025 * 0.830 -
S (L/250) 3.000 * 2.063 1.298 0.875 0.619 0.455 -
1350
U 3.671 * 2.456 * 1.777 * 1.353 1.069 * 0.867 -
S (L/250) 3.000 * 2.122 * 1.346 0.911 0.647 0.477 -
1275
U 3.737 * 2.533 * 1.846 * 1.412 * 1.118 * 0.909 -
S (L/250) 3.000 * 2.195 * 1.401 * 0.953 0.679 0.502 -
1200
U 3.832 * 2.627 * 1.927 * 1.480 * 1.176 * 0.958 -
S (L/250) 3.000 * 2.283 * 1.467 * 1.002 0.716 0.530 0.404
1125
U 3.958 * 2.740 * 2.022 * 1.559 * 1.241 * 1.013 * 0.843
S (L/250) 3.000 * 2.390 * 1.545 * 1.059 0.759 0.563 0.429
1050
U 4.118 * 2.876 * 2.134 * 1.651 * 1.318 * 1.077 * 0.898
S (L/250) 3.000 * 2.520 * 1.637 * 1.126 0.809 0.601 0.459
975
U 4.319 * 3.041 * 2.267 * 1.759 * 1.407 * 1.152 * 0.961
S (L/250) 3.000 * 2.677 * 1.748 * 1.206 0.868 0.646 0.494
900
U 4.500 * 3.239 * 2.425 * 1.887 * 1.512 * 1.240 * 1.036 *
S (L/250) 3.000 * 2.869 * 1.881 * 1.302 0.939 0.700 0.536
825
U 4.500 * 3.479 * 2.615 * 2.040 * 1.638 * 1.345 * 1.125 *
S (L/250) 3.000 * 3.000 * 2.044 * 1.418 * 1.025 * 0.765 0.587
750
U 4.500 * 3.775 * 2.847 * 2.226 * 1.790 * 1.472 * 1.232 *
S (L/250) 3.000 * 3.000 * 2.246 * 1.562 * 1.131 * 0.845 0.649
675
U 4.500 * 4.143 * 3.134 * 2.456 * 1.977 * 1.627 * 1.363 *
S (L/250) 3.000 * 3.000 * 2.503 * 1.744 * 1.265 * 0.946 0.727
600
U 4.500 * 4.500 * 3.496 * 2.745 * 2.213 * 1.823 * 1.528 *
Transom Width (mm) 1500 1750 2000 2250 2500 2750 3000

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 13
400 Narrowline
Span Table
2 PIECE TRANSOM - EN5020 / EN9499
Note:
Serviceability pressures have been limited to a maximum
Serviceability Pressure of 3000Pa.
Serviceability pressures have not been limited by water
performance. Where water performance is necessary, refer to
Product Specifications page.
As lowlight mullions under transom are assumed, no
consideration has been given to the deadload component of
loading.

* Indicates the "Braced Bead" (EP12761) should be used.

Transom Spacing
Maximum Design Pressure (kPa)
(mm)
S (L/250) 3.000 * 2.536 * 1.569 * 1.046 * 0.735 0.538 0.406
1500
U 4.500 * 3.156 * 2.245 * 1.692 * 1.327 * 1.071 * 0.885
S (L/250) 3.000 * 2.582 * 1.612 * 1.080 0.762 0.559 0.423
1425
U 4.500 * 3.220 * 2.311 * 1.751 * 1.378 * 1.116 * 0.923
S (L/250) 3.000 * 2.642 * 1.663 * 1.120 0.793 0.583 0.442
1350
U 4.500 * 3.303 * 2.390 * 1.820 * 1.437 * 1.166 * 0.966
S (L/250) 3.000 * 2.717 * 1.723 * 1.166 0.829 0.611 0.464
1275
U 4.500 * 3.406 * 2.483 * 1.899 * 1.504 * 1.223 * 1.015 *
S (L/250) 3.000 * 2.810 * 1.794 * 1.220 0.869 0.642 0.489
1200
U 4.500 * 3.532 * 2.591 * 1.991 * 1.581 * 1.288 * 1.071 *
S (L/250) 3.000 * 2.924 * 1.878 * 1.283 0.917 0.679 0.517
1125
U 4.500 * 3.685 * 2.719 * 2.097 * 1.669 * 1.363 * 1.134 *
S (L/250) 3.000 * 3.000 * 1.978 * 1.356 0.972 0.721 0.550
1050
U 4.500 * 3.868 * 2.870 * 2.220 * 1.772 * 1.449 * 1.208 *
S (L/250) 3.000 * 3.000 * 2.096 * 1.442 * 1.036 * 0.770 0.588
975
U 4.500 * 4.089 * 3.048 * 2.366 * 1.892 * 1.549 * 1.293 *
S (L/250) 3.000 * 3.000 * 2.238 * 1.544 * 1.112 * 0.828 0.633
900
U 4.500 * 4.355 * 3.261 * 2.538 * 2.034 * 1.668 * 1.393 *
S (L/250) 3.000 * 3.000 * 2.409 * 1.667 * 1.203 * 0.897 0.687
825
U 4.500 * 4.500 * 3.516 * 2.744 * 2.203 * 1.809 * 1.512 *
S (L/250) 3.000 * 3.000 * 2.618 * 1.816 * 1.313 * 0.980 0.751
750
U 4.500 * 4.500 * 3.828 * 2.994 * 2.407 * 1.979 * 1.656 *
S (L/250) 3.000 * 3.000 * 2.877 * 2.001 * 1.448 * 1.083 * 0.831
675
U 4.500 * 4.500 * 4.214 * 3.302 * 2.659 * 2.188 * 1.833 *
S (L/250) 3.000 * 3.000 * 3.000 * 2.234 * 1.619 * 1.212 * 0.931
600
U 4.500 * 4.500 * 4.500 * 3.691 * 2.976 * 2.451 * 2.054 *
Transom Width (mm) 1500 1750 2000 2250 2500 2750 3000

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on a combination of approved AS2047 testing data and theoretical section properties.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 14 14-06-2016


01-07-2022 ©
400 Narrowline
Span Table
110mm MIDRAIL - EN2849
Note:
Serviceability pressures have been limited to a maximum Serviceability
Pressure of 2200Pa.
Serviceability pressures have not been limited by water performance.
Where water performance is necessary, refer to Product Specifications
page.
This table has been based on a below midrail height of 900mm.

Above Midrail
Maximum Design Pressure (kPa)
Height (mm)
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.853
2100
U 3.300 3.300 3.300 3.300 3.300 3.230 2.561
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.853
2025
U 3.300 3.300 3.300 3.300 3.300 3.230 2.561
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.853
1950
U 3.300 3.300 3.300 3.300 3.300 3.230 2.561
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.853
1875
U 3.300 3.300 3.300 3.300 3.300 3.230 2.561
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.853
1800
U 3.300 3.300 3.300 3.300 3.300 3.230 2.561
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.855
1725
U 3.300 3.300 3.300 3.300 3.300 3.230 2.565
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.175 0.858
1650
U 3.300 3.300 3.300 3.300 3.300 3.230 2.577
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.177 0.863
1575
U 3.300 3.300 3.300 3.300 3.300 3.236 2.596
S (L/250) 2.200 2.200 2.200 2.200 1.670 1.182 0.871
1500
U 3.300 3.300 3.300 3.300 3.300 3.253 2.622
S (L/250) 2.200 2.200 2.200 2.200 1.672 1.191 0.881
1425
U 3.300 3.300 3.300 3.300 3.300 3.280 2.656
S (L/250) 2.200 2.200 2.200 2.200 1.681 1.203 0.894
1350
U 3.300 3.300 3.300 3.300 3.300 3.300 2.698
S (L/250) 2.200 2.200 2.200 2.200 1.696 1.219 0.909
1275
U 3.300 3.300 3.300 3.300 3.300 3.300 2.749
S (L/250) 2.200 2.200 2.200 2.200 1.717 1.240 0.927
1200
U 3.300 3.300 3.300 3.300 3.300 3.300 2.808
Midrail Width (mm) 900 1050 1200 1350 1500 1650 1800

LEGEND: S = Serviceability Pressure, U = Ultimate Pressure

NOTE: This table is based on theoretical section properties, not on approved tests as specified by AS2047.
A maximum stress level of 110MPa has been applied when generating this table.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 16-06-2016
01-07-2022 Sec9 Span Tables - Page 15
400 Narrowline
Maximum Glass Thickness Table - Deadload Assessment
TUBULAR TRANSOM - EN5021
Note:
Glass thickness has been limited to 10mm as dictated by the capacity of
the suite.
These tables have been developed to assist Fabricators in making an
assessment of the maximum glass thickness that the transom member can
support before it is considered unstable (deflection & stress).

Wind load and human impact requirements are not included in the tables
below. A glass thickness assessment for windload and human impact must
still be completed in accordance with AS1288.

Height Above
Maximum Glass Thickness with Support Blocks at 1/4 Points (mm)
Transom (mm)
1200 10 8 6 4 - - - - -
1100 10 10 6 5 - - - - -
1000 10 10 6 5 4 - - - -
900 10 10 8 6 4 - - - -
800 10 10 8 6 5 4 - - -
700 10 10 10 8 6 4 - - -
600 10 10 10 8 6 5 4 - -
Transom Width (mm) 1400 1600 1800 2000 2200 2400 2600 2800 3000
Downward
2.3 2.7 3.0 3.3 3.7 4.0 4.3 4.7 5.0
Deflection (mm)

Height Above
Maximum Glass Thickness with Support Blocks at 1/8 Points (mm)
Transom (mm)
1200 10 10 10 8 6 5 4 - -
1100 10 10 10 8 6 5 4 - -
1000 10 10 10 10 6 6 4 - -
900 10 10 10 10 8 6 5 4 -
800 10 10 10 10 8 6 6 4 -
700 10 10 10 10 10 8 6 5 4
600 10 10 10 10 10 10 8 6 5
Transom Width (mm) 1400 1600 1800 2000 2200 2400 2600 2800 3000
Downward
2.3 2.7 3.0 3.3 3.7 4.0 4.3 4.7 5.0
Deflection (mm)

NOTE: This table is based on theoretical section properties, not on approved tests as specified by AS2047.
A deflection ratio of L/600 has been assumed, resulting in the individual deflection figures listed on the tables.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 16 14-06-2016


01-07-2022 ©
400 Narrowline
Maximum Glass Thickness Table - Deadload Assessment
2 PIECE TRANSOM - EN5020 / EN9499
Note:
Glass thickness has been limited to 10mm as dictated by the capacity of
the suite.
These tables have been developed to assist Fabricators in making an
assessment of the maximum glass thickness that the transom member can
support before it is considered unstable (deflection & stress).

Wind load and human impact requirements are not included in the tables
below. A glass thickness assessment for windload and human impact must
still be completed in accordance with AS1288.

Height Above
Maximum Glass Thickness with Support Blocks at 1/4 Points (mm)
Transom (mm)
1200 8 6 4 - - - - - -
1100 10 6 4 - - - - - -
1000 10 6 5 - - - - - -
900 10 8 6 4 - - - - -
800 10 8 6 4 - - - - -
700 10 10 6 5 4 - - - -
600 10 10 8 6 4 - - - -
Transom Width (mm) 1400 1600 1800 2000 2200 2400 2600 2800 3000
Downward
2.3 2.7 3.0 3.3 3.7 4.0 4.3 4.7 5.0
Deflection (mm)

Height Above
Maximum Glass Thickness with Support Blocks at 1/8 Points (mm)
Transom (mm)
1200 10 10 8 6 4 - - - -
1100 10 10 8 6 5 - - - -
1000 10 10 10 6 5 4 - - -
900 10 10 10 8 6 4 - - -
800 10 10 10 8 6 5 4 - -
700 10 10 10 10 6 6 4 - -
600 10 10 10 10 8 6 5 4 -
Transom Width (mm) 1400 1600 1800 2000 2200 2400 2600 2800 3000
Downward
2.3 2.7 3.0 3.3 3.7 4.0 4.3 4.7 5.0
Deflection (mm)

NOTE: This table is based on theoretical section properties, not on approved tests as specified by AS2047.
A deflection ratio of L/600 has been assumed, resulting in the individual deflection figures listed on the tables.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

© 14-06-2016
01-07-2022 Sec9 Span Tables - Page 17
400 Narrowline
Maximum Glass Thickness Table - Deadload Assessment
110mm MIDRAIL - EN2849
Note:
Glass thickness has been limited to 10mm according to the capacity of
the suite.

These tables have been developed to assist Fabricators in making an


assessment of the maximum glass thickness that the midrail member can
support before it is considered unstable (deflection & stress).

Wind load and human impact requirements are not included in the tables
below. A glass thickness assessment for windload and human impact
must still be completed in accordance with AS1288.

Height Above
Maximum Glass Thickness with Support Blocks at 1/4 Points (mm)
Midrail (mm)
2150 10 10 10 10 10 10 10
1950 10 10 10 10 10 10 10
1800 10 10 10 10 10 10 10
1650 10 10 10 10 10 10 10
1500 10 10 10 10 10 10 10
1350 10 10 10 10 10 10 10
1200 10 10 10 10 10 10 10
Midrail Width (mm) 600 800 1000 1200 1400 1600 1800
Downward
1.0 1.3 1.7 2.0 2.3 2.7 3.0
Deflection (mm)

Height Above
Maximum Glass Thickness with Support Blocks at 1/8 Points (mm)
Midrail (mm)
2150 10 10 10 10 10 10 10
1950 10 10 10 10 10 10 10
1800 10 10 10 10 10 10 10
1650 10 10 10 10 10 10 10
1500 10 10 10 10 10 10 10
1350 10 10 10 10 10 10 10
1200 10 10 10 10 10 10 10
Midrail Width (mm) 600 800 1000 1200 1400 1600 1800
Downward
1.0 1.3 1.7 2.0 2.3 2.7 3.0
Deflection (mm)

NOTE: This table is based on theoretical section properties.


A deflection ratio of L/600 has been assumed, resulting in the individual deflection figures listed on the tables.

Please read in conjunction with Important Conditions – Index (also available on Capral website)

Sec9 Span Tables - Page 18 16-06-2016


01-07-2022 ©

You might also like