Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.
“जान1 का अ+धकार, जी1 का अ+धकार” “प0रा1 को छोड न' 5 तरफ”
Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru “The Right to Information, The Right to Live” “Step Out From the Old to the New”
IS 1381-1 (2003): Laboratory Glassware - Narrow-Necked
Boiling Flasks [CHD 10: Glassware]
“!ान $ एक न' भारत का +नम-ण”
Satyanarayan Gangaram Pitroda “Invent a New India Using Knowledge”
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता ह”
है” ह Bhartṛhari—Nītiśatakam “Knowledge is such a treasure which cannot be stolen” IS 1381 (Part 1) : 2003 ISO 1773 : 1997 Reaffirmed 2008
Indian Standard LABORATORY GLASSWARE — NARROW-NECKED BOILING FLASKS ( Second Revision )
(CHD 10) Reprography Unit, BIS, New Delhi, India IS 1381 (Part 1) : 2003 ISO 1773 : 1997
Indian Standard LABORATORY GLASSWARE — NARROW-NECKED BOILING FLASKS ( Second Revision ) 1 Scope
This International Standard specifies requirements and dimensions for an internationally acceptable series of conical flasks and of flat-bottom and round-bottom flasks for general laboratory purposes. The flasks are provided for
- direct use in a laboratory, fitting together with other equipment for general laboratory purposes;
- further work up to other products.
NOTE — Annex A lists additional International Standards for other general-purpose laboratory glassware.
2 Normative reference
The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
ISO 3585:1991, Borosilicate glass 3.3 — Properties.
3 Conical flasks
3.1 Series of nominal capacity
The series of nominal capacities of conical flasks is as follows (given in millilitres):
The nominal capacity of a flask is the value, selected from the series given in 3.1, which is closest to but not larger than the actual volume to the base of neck.
NOTE — The body dimensions recommended in table 1 take this requirement into account and as far as possible are in accordance with the current production of flasks.
3.3 Material
Flasks shall be made from borosilicate glass 3.3 in accordance with ISO 3585, and shall be free from visible defects and free from internal stress which would impair the performance of the flask. ISO 1 7 7 3 : 1 9 9 7 3.4 Construction
3.4.1 Stability
The flasks shall stand vertically without rocking or spinning when placed on a level surface.
3.4.2 Neck
The neck of the flask shall be substantially circular in cross-section and the mouth of the neck shall not be belled to any considerable distance from the top. The top of the neck shall be suitably strengthened.
3.5 Dimensions
3.5.1 Recommended dimensions
Dimensions for conical flasks are given in table 1.
The length of the neck shall be 1 to 1,25 times the external diameter of the neck.
3.5.3 Dimensions of base
The radius at the junction between the base and the side of the flask shall be between 15 % and 20 % of the maximum external diameter.
3.5.4 Wall thickness
Minimum values for the wall thickness are given in table 1. Substantial local irregularities shall be avoided. Manufacturers shall take care that minimum wall thicknesses are compatible with safety requirements.
2 IS 1381 (Part 1) : 2 0 0 3 ISO 1 7 7 3 : 1 9 9 7 NOTE — Flasks may also be manufactured with minimum wall thickness of 1,0 mm for 1 000 ml flasks and of 1,1 mm for 2 000 ml flasks.
4 Flat-bottom and round-bottom flasks
4.1 Series of nominal capacities
The series of nominal capacities of flat-bottom and round-bottom flasks is as follows (given in millilitres):
The nominal capacity of a flask is the value, selected from the series given in 4.1, which is closest to but not larger than the actual volume to the base of neck.
NOTE — The body dimensions recommended in table 2 take this requirement into account, and as far as possible are in accordance with the current production of flasks.
4.3 Material
Flasks shall be made from borosilicate glass 3.3 in accordance with ISO 3585, and shall be free from visible defects and free from internal stress which would impair the performance of the flask.
4.4 Construction
4.4.1 Stability
The flat-bottom flasks shall stand vertically without rocking or spinning when placed on a level surface.
4.4.2 Neck
The neck of the flask shall be substantially circular in cross-section and the mouth of the neck shall not be belled to any considerable distance from the top. The top of the neck shall be suitably strengthened.
4.5 Dimensions
4.5.1 Recommended dimensions
Dimensions for flat-bottom and round-bottom flasks are given in table 2.
4.5.2 Dimensions of base
The diameter of the base of flat-bottom flasks shall be approximately 50 % of the maximum external diameter. IS 1 3 8 1 (Part 1) : 2 0 0 3 ISO 1 7 7 3 : 1 9 9 7 Table 2 — Dimensions of flat- and round-bottom flasks
Minimum values for the wall thickness are given in table 2. Substantial local irregularities shall be avoided Manufacturers shall take care that minimum wall thicknesses are compatible with safety requirements.
NOTE — Flasks may also be manufactured with minimum wall thickness of 0,8 mm for 250 ml and 500 ml flasks, and ??? 1,1 mm for 1 000 ml flasks.
5 Marking
The following inscriptions shall be permanently and legibly marked on all conical, flat-bottom and roun bottom flasks:
a) the nominal volume of the flask, e.g. "100 ml" (or "100");
b) the maker's or vendor's name or mark;
c) each flask shall also bear an area with a surface suitable for marking with a pencil.
It is recommended that reference is made on each flask to this International Standard.
IS 1381 (Part 1) : 2 0 0 3 ISO 1 7 7 3 : 1 9 9 7
Annex A (informative)
Bibliography
1] ISO 383:1976, Laboratory glassware — Interchangeable conical ground joints.
2] ISO 384:1978, Laboratory glassware — Principles of design and construction of volumetric glassware. 3] ISO 641:1975, Laboratory glassware — Interchangeable spherical ground joints. 4] ISO 3819:1985, Laboratory glassware — Beakers 5] ISO 4142:1997, Laboratory glassware — Test tubes and culture tubes. 6] ISO 4785:1997, Laboratory glassware — Straight-bore glass stopcocks for general purposes. 7] ISO 4796:1977, Laboratory glassware — Bottles. 8] ISO 4797:1981, Laboratory glassware — Flasks with conical ground joints. 9] ISO 4799:1978, Laboratory glassware — Condensers. 10] ISO 4800:1977, Laboratory glassware — Separating funnels and dropping funnels. 11] ISO 6556:1981, Laboratory glassware — Filter flasks.
5 Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in any form without the prior permission in writing of BIS. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating to copyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of 'BIS Catalogue' and 'Standards : Monthly Additions'.
This Indian Standard has been developed from Doc : No. CHD 10 ( 1080).
Amendments Issued Since Publication
Amend No. Date of Issue Text Affected
BUREAU OF INDIAN STANDARDS
Headquarters: Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110 002 Telegrams: Manaksanstha Telephones: 2323 0131, 2323 3375, 2323 9402 (Common to all offices) Regional Offices: Telephone Central: Manak Bhavan, 9 Bahadur Shah Zafar Marg 2323 7617 NEW DELHI 110002 2323 3841
Eastern : 1/14 C. I. T. Scheme VII M, V. I. P. Road, Kankurgachi . 2337 8499, 2337 8561 KOLKATA 700 054 2337 8626, 2337 9120 Northern : SCO 335-336, Sector 34-A, CHANDIGARH 160 022 60 3843 60 9285 Southern : C. I. T. Campus, IV Cross Road, CHENNAI 600 113 2254 1216, 2254 1442 2254 2519, 2254 2315 Western : Manakalaya, E9 MIDC, Marol, Andheri(East) 2832 9295, 2832 7858 MUMBAI 400093 2832 7891, 2832 7892
