FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES

118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

CERTIFICATE OF ACCREDITATION
(AS PER ISO/IEC 17025:2017)

This is to attest that

M/s WAGA Calibration Services (PVT) Ltd.

173, High Level Road, Maharagama, Sri Lanka

Calibration Laboratory
has demonstrated compliance with ISO/IEC Standard 17025:2017, General requirements for
the competence of testing and calibration laboratories and supplementary criteria for
Calibration laboratories.

Certificate Number: CL-123

Issue Date: 04.05.2024 Valid Until: 03.05.2026

The certificate remains valid for the Scope of Accreditation as specified in the annexure
subject to continued satisfactory compliance to the above standard and the relevant
requirements of FDAS. (for scope of accreditation visit website www. fdasindia.org).
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

Source Mode
1 DC Voltage – Generate WAGA / CM/030, 1 mV to 200 mV 0.15 µV to 1.8 µV
(Analog and digital WAGA/CM/017
equipment/indictor, Using Multifunction 0.2 V to 1000 V 1.8 µV to 8.2 mV
multimeter, Clamp Calibrator Direct method
meter, pH meter
indicator)
2 DC Current – Generate WAGA / CM/030, 1 µA to 200 mA 0.82 µA to 0.015 mA
(Analog and digital WAGA/CM/017 0.2 A to 20 A 0.015 mA to 2.3 mA
equipment/indictor, Using Multifunction 20 A to 1000 A 0.12 A to 5.8 A
multimeter, Clamp Calibrator Direct method
meter, leakage current WAGA/CM/027
clamp meter) Using clamp coil
3 DC resistance WAGA / CM/030, 1 Ω to 1000 Ω 0.59 mΩ to 0.59 Ω
Generate(Analog and WAGA/CM/017
digital equipment Using Multifunction 1 kΩ to 1000 kΩ 0.59 Ω to 0.11 kΩ
/indictor, multimeter Calibrator Direct method
Clamp meter) 1 MΩ to 120 MΩ 0.11 kΩ to 0.026 MΩ

Discrete resistance 1, 10, 100 Ω 2.1 mΩ

Generate 1, 10, 100 kΩ 2.1 Ω
2.1 kΩ
1, 10, 100 MΩ
0.002 GΩ
1 GΩ

Dealing Officer
Page 1 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

4 AC Voltage Generate WAGA / CM/030 & 1 mV to 200 mV 0.0053 mV to 0.031

(Analog and digital WAGA/CM/017 @ (50 Hz to mV
equipment/indictor, Using Multifunction 100 kHz)
multimeter, Clamp Calibrator Direct method 0.2 V to 1000 V 0.031 mV to 0.17 V
meter) (@ 50 Hz to 1kHz)
5 AC Current Generate WAGA / CM/030 & 10 µA to 200 µA 0.03 µA to 0.039 µA
(Analog and digital WAGA/CM/017 @( 50 Hz to 1
equipment/indictor, Using Multifunction kHz)
multimeter, Clamp Calibrator Direct method 0.2 mA to 200 mA 0.039 µA to 0.041
meter) @ (50 Hz to 1kHz) mA
Inductance Generate 0.2 A to 20 A 0.041 mA to 6.9 mA
@ (50 Hz to 1
kHz)
WAGA/CM/027 20 A to 1000 A 0.12 A to 5.8 A
Using Clamp coil @( 50 Hz)
6 Inductance Generate WAGA / CM/030 & 1 mH to 10 H 0.0016 mH to 0.016H
(Analog and digital WAGA/CM/017
equipment/indictor, Using Multifunction
multimeter, LCR Calibrator Direct method
meter)
7 Capacitance WAGA / CM/030 & 1 nF to 100 µF 0.0011 nF to 0.11 µF
Generate(Analog and WAGA/CM/017
digital equipment Using Multifunction
/indictor,multimeter, Calibrator Direct method
LCR meter)

Dealing Officer
Page 2 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

8 Power FactorGenerate WAGA / CM/030 0.2 to 1 0.006%

(Analog and digital Using Multifunction (Lag & Lead)
equipment/indictor, Calibrator Direct method
power analyzer)
9 Frequency Generate WAGA / CM/030 & 1 Hz to 100 MHz 5.8 mHz to 2.4 kHz
(Analog and digital WAGA/CM/017
equipment/indictor, Using Multifunction
multimeter, Clamp Calibrator Direct method
meter)
Measure Mode
1 DC Voltage Measure WAGA/CM/030 using 1 mV to 100 mV 0.0093 mV to 0.013 mV
(Analog and Digital Multimeter as perdirect 100 mV to 10 V 0.013 mV to 0.47 mV
Electrical Equipment measurement of 0.47 mV to 6.0 mV
10 V to 100 V
withsources/power electrical parameter 6.0 mV to 0.067 V
supply, multiproduct 100 V to 1000 V
calibrator)
2 AC Voltage Measure WAGA/CM/030 using @50 Hz to 1 kHz
(Analog and Digital Multimeter as per direct 10 mV to 100 mV
0.054 mV to 0.12 mV
Electrical Equipment measurement of 100 mV to 10 V 0.12 mV to 0.011 V
with sources/power electrical parameter 10 V to 100 V 0.011 V to 0.11 V
supply, multiproduct 100 V to 750 V 0.33 V to 0.79 V
calibrator)

Dealing Officer
Page 3 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

3 DC Current Measure WAGA/CM/030 using 10 mA to 100 mA 0.0024 mV to 0.065 mA

(Analog and Digital Multimeter as per direct 100 mA to 1 A 0.065 mA to 1.3 mA
Electrical Equipment measurement of 1 A to 3 A 1.3 mA to 5.4 mA
with sources/power electrical parameter 3 A to 10 A 0.039 A to 0.14 A
supply, multiproduct
calibrator)
4 AC Current Measure WAGA/CM/030 using 50 Hz to 500 Hz
(Analog and Digital Multimeter as per direct 0.1 A to 1 A 0.59 mA to 1.8 mA
Electrical Equipment measurement of 1 A to 3 A 1.8 mA to 8.6 mA
withsources/power electrical parameter 3 A to 10 A 8.6 mA to 0.20 A
supply, multiproduct
calibrator)
5 Frequency Measure WAGA/CM/030 using 3 Hz to 1 kHz 3.5 mHz to 0.011Hz
(Analog and Digital Multimeter as per direct 1 kHz to 100 kHz 0.011 Hz to 0.016 kHz
Electrical Equipment measurement of 100 kHz to 300 kHz 0.016 Hz to 0.037 kHz
withsources/power electrical parameter
supply, multiproduct
calibrator)
6 DC ResistanceMeasure WAGA/CM/030 using 0Ω to 0.1 kΩ 0.0047 Ω to 0.017 Ω
(Analog and Digital Multimeter as per direct 0.1 kΩ to 10 kΩ 0.017 Ω to 0.0014 kΩ
Electrical Equipment measurement of 10 kΩ to 100 kΩ 0.0014 kΩ to 0.014 Ω
withsources/power electrical parameter 0.1 MΩ to 10 MΩ 0.014 kΩ to 5.0 kΩ
supply, multiproduct 10 MΩ to 100 MΩ 5.0 kΩ to 0.94 MΩ
calibrator)

Dealing Officer
Page 4 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

7 Capacitance Measure WAGA/CM/030 using 10 pF to 100 pF 0.016 pF to 0.14 pF

(Analog and Digital Multimeter as per direct 100 pF to 100 nF 0.14 pF to 0.14 nF
Electrical Equipment measurement of 100 nF to 1 μF 0.14 nF to 1.8 nF
withsources/power electrical parameter 1 μF to 1000 μF 1.8 nF to 5.2 μF
supply, multiproduct
calibrator)
8 Inductance Measure WAGA/CM/030 using 100 μH to 1 mH 0.15 μH to 1.4 μH
(Analog and Digital Multimeter as per direct 1 mH to 100 mH 1.4 μH to 0.14 mH
Electrical Equipment measurement of 100 mH to 1 H 0.14 mH to 1.4 mH
withsources/power electrical parameter
supply, multiproduct
calibrator)
9 Insulation Testers WAGA/CM/028 100 kΩ to 5 MΩ 1.2 kΩ to 5.8 kΩ
using Insulation Tester 5 MΩ to 50 MΩ 0.058 MΩ to 0.58 MΩ
Calibration System as 50 MΩ to 100 MΩ 0.58 MΩ to 1.2 MΩ
source for generation of 100 MΩ to 1 GΩ 1.2 MΩ to 0.024 GΩ
electrical parameter
1 GΩ 10 GΩ 0.024 GΩ to 0.59 GΩ
10 GΩ to 100 GΩ 0.59 GΩ to 5.8 GΩ
WAGA/CM/028 0 kV to 2 kV 0.024 kV
Open circuit voltage 2 kV to 10 kV 0.024 kV to 0.31 kV
using Insulation Tester
Calibration System as per
direct measurement of
electrical parameter

Dealing Officer
Page 5 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

WAGA/CM/028 0.5 mA to 2 mA 0.025 mA to 0.037mA

Short Circuit current 2 mA to 20 mA 0.037 mA to 0.37 mA
using Insulation Tester
Calibration System as per
direct measurementof
electrical parameter
Temperature Simulation (Source Mode)
1 Temperature WAGA/CM/023 Using K -200 ºC to 0.14 ºC
Indicators and multifunction calibrator as T/C 1350 ºC
Simulators by J -200 ºC to 0.13 ºC
per EURAMET cg-11(2011)
Electrical Simulation T/C
Guideline on the Calibration 1200 ºC
and Measurement
(Temperature simulator of Temperature Indicators T -200 ºC to 0.13 ºC
T/C 400 ºC
intended to be used with and Simulators by Electrical
thermocouple) Simulation and R -50 ºC to 0.14 ºC
Measurement T/C 1750 ºC
S -50 ºC to 0.14 ºC
T/C 1750 ºC
B 600 ºC to 0.16 ºC
T/C 1800 ºC
E -200 ºC to 0.13 ºC
T/C 1000 ºC
N -200 ºC to 0.13 ºC
T/C 1300 ºC
PT -180 ºC to 0.09 ºC
100 850 ºC

Dealing Officer
Page 6 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (Laboratory based)

Temperature Simulation (Measure Mode)

1 Temperature WAGA/CM/023 Using K -200 ºC to 0.36 ºC
Indicatorsand T/C 1350 ºC
process calibrator
Simulators by calibrator as per J -210 ºC to 0.36 ºC
Electrical Simulation T/C 1200 ºC
EURAMET cg-11
and Measurement T -200 ºC to 0.36 ºC
Guideline on the 400 ºC
(Temperature T/C
Calibration of
simulator intended to R -50 ºC to 0.36 ºC
be used with Temperature 1750 ºC
T/C
Indicators and
thermocouple) Simulators by S -50 ºC to 0.36 ºC
Electrical Simulation T/C 1750 ºC
and Measurement B 600 ºC to 0.37 ºC
T/C 1800 ºC
E -200 ºC to 0.36 ºC
T/C 1000 ºC
N -200 ºC to 0.36 ºC
T/C 1300 ºC
PT -180 ºC to 0.012 ºC
100 850 ºC
Time
1 Stop watch/Timers WAGA/CM/055 using 1 s to 18000 s 0.18 sec
stopwatch calibrator as 18000 s to 86400 s 0.22 sec
per direct comparison

Dealing Officer
Page 7 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (At Site)

Source Mode
1 DC Voltage Generate WAGA/CM/030 using 1 mV to 10 mV 0.6 µV to 0.77 µV
(Analog and Digital Multifunction Process 10 mV to 75 mV 0.77 µV to 3.8 µV
Electrical Measuring Calibrator as per direct 75 mV to 12 V 3.8 µV to 0.61 mV
Equipment/Indicator, method
pH meter)
2 DC Current Generate 0 mA to 22 mA 0.58 µV to 4.5 µV
(Analog and Digital
Electrical Measuring
Equipment/Indicator)
3 Digital Frequency 100 Hz to 50 kHz 0.063 Hz to 0.51 Hz
Generate (Analog and
Digital Electrical
Measuring Equipment
/Indicator)
4 Resistance Generate 1 Ω to 400 Ω 0.0059 Ω to 0.021 Ω
(Analog and Digital 400 Ω to 4.0 kΩ 0.021 Ω to 0.21 Ω
Electrical Measuring
Equipment/Indicator)
Measure Mode
1 DC Voltage Measure WAGA/CM/030 using 1 mV to 100 mV 0.0093 mV to 0.013 mV
(Analog and Digital Multimeter as per direct 100 mV to 10 V 0.013 mV to 0.47 mV
Electrical Equipment measurement of 10 V to 100 V 0.47 mV to 6.0 mV
with sources) electrical parameter 100 V to 1000 V 6.0 mV to 0.067 V

Dealing Officer
Page 8 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (At Site)

2 AC Voltage Measure WAGA/CM/030 using 50 Hz to 1 kHz

(Analog and Digital Multimeter as per direct 10 mV to 100 mV 0.054 mV to 0.12 mV
Electrical Equipment measurement of 100 mV to 10 V 0.12 mV to 0.011 V
with sources) electrical parameter 10 V to 100 V 0.011 V to 0.11 V
100 V to 750 V 0.33 V to 0.79 V
3 DC Current Measure WAGA/CM/030 using 10 mA to 100 mA 0.0024 mV to 0.065 mA
(Analog and Digital Multimeter as per direct 0.065 mA to 1.3 mA
Electrical Equipment measurement of 100 mA to 1 A 1.3 mA to 5.4 mA
with sources) electrical parameter 1 A to 3 A 0.039 A to 0.14 A
3 A to 10 A
4 AC Current Measure WAGA/CM/030 using 50 Hz to 500 Hz
(Analog and Digital Multimeter as per direct 0 A to 1 A 0.59 mA to 1.8 mA
Electrical Equipment measurement of 1 A to 3 A 1.8 mA to 8.6 mA
withsources) electricalparameter 3 A to 10 A 8.6 mA to 0.2 A
5 Frequency Measure WAGA/CM/030 using 1 Hz to 1 kHz 3.5 mHz to 0.12 Hz
(Analog and Digital Multimeter as per direct 1 kHz to 100 kHz 0.12 Hz to 0.011 kHz
Electrical Equipment measurement of 100 kHz to 300 kHz 0.011 Hz to 0.037 kHz
withsources) electricalparameter
6 Resistance Measure WAGA/CM/030 using 0Ω to 0.1 kΩ 0.0047 Ω to 0.017 Ω
(Analog and Digital Multimeter as per direct 0.1 kΩ to 10 kΩ 0.017 Ω to 0.0014 kΩ
Electrical Equipment measurement of 10 kΩ to 100 kΩ 0.0014 kΩ to 0.014 Ω
withsources) electricalparameter 0.1 MΩ to 10 MΩ 0.014 kΩ to 5.0 kΩ
10 MΩ to 100 MΩ 5.0 kΩ to 0.94 MΩ

Dealing Officer
Page 9 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (At Site)

7 Inductance Measure WAGA/CM/030 using 100 μH to 1 mH 0.15 μH to 1.4 μH

(Analog and Digital Multimeter as per direct 1 mH to 100 mH 1.4 μH to 0.14 mH
Electrical Equipment measurement of 100 mH to 1 H 0.14 mH to 1.4 mH
with sources/power electricalparameter
supply, multiproduct
calibrator)
Temperature Simulation (Source Mode)
1 Temperature WAGA/CM/023 Using K -200 ºC to 0.14 ºC
Indicators and multifunction calibrator T/C 1370 ºC
Simulators by as per EURAMET cg- J -210 ºC to 0.13 ºC
Electrical Simulation 11(2011) Guideline on T/C 1200 ºC
and Measurement the Calibration of T -200 ºC to 0.13 ºC
(Temperature Temperature Indicators T/C 400 ºC
indicators/controllers) and Simulators by R -50 0C to 0.14 ºC
Electrical Simulation and T/C 1765 ºC
Measurement S -50 ºC to 0.14 ºC
T/C 1760 ºC
B 300 ºC to 0.16 ºC
T/C 1800 ºC
E -200 ºC to 0.13 ºC
T/C 1000 ºC
N -200 ºC to 0.13 ºC
T/C 1300 ºC
PT -180 ºC to 0.09 ºC
100 850 ºC

Dealing Officer
Page 10 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Electro - Technical Calibration (At Site)

Temperature Simulation (Measure Mode)

1 Temperature WAGA/CM/023 Using K -200 ºC to 0.36 0C
Indicators and multifunction calibrator as T/C 1370 ºC
Simulators by per EURAMET cg-
Electrical Simulation 11(2011) Guideline on the J -210 ºC to 0.36 0C
and Measurement Calibration of T/C 1200 ºC
(Temperature Temperature Indicators
simulator intended to and Simulators by T -200 ºC to 0.36 0C
T/C 400 ºC
be used with Electrical Simulation and
thermocouple) Measurement
R -50 ºC to 0.36 0C
T/C 1765 ºC

S -50 ºC to 0.36 0C
T/C 1760 ºC

B 200 ºC to 0.37 0C
T/C 1800 ºC

E -200 ºC to 0.36 0C
T/C 1000 ºC

N -200 ºC to 0.36 0C
T/C 1300 ºC

P -180 ºC to 0.012 0C
850 ºC
T100

Dealing Officer
Page 11 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (Laboratory based)

Group: Dimension
1 Dial gauge WAGA/CM/035 0 to 25 mm 0.9 µm
Using 0 grade gauge block 25 mm to 50 mm 5.8 µm
as per the USBR 1007-89-
Procedure for Calibrating
dialindicators
2 Steel Ruler WAGA/CM/014 using 0 to 1000 mm 0.58 mm
rulercomparator as per
Linear measurement by
direct comparison
3 Vernier Caliper WAGA/CM/036 0 mm to 300 mm 12 µm
Using 0 grade gauge 300 mm to 500 mm 12 µm
block as per the - 500 mm to 1000 mm 12 µm
IS:16491:2021 Speciation (External
for Vernier Caliper calibration/Depth
calibration)
4 External Micrometer WAGA/CM/013 0.5 mm to 100 mm 1.4 µm
Using 0 grade gauge 100 mm to 500 mm 1.8 µm
block as per - 500 mm to 1000 mm 10 µm
IS:2967 :1983
Specificationfor external
Micrometer

Dealing Officer
Page 12 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (Laboratory based)

5 Height Gauge WAGA/CM/037 0.5 mm to 100 mm 7.0 µm

Using 0 grade gauge block 100 mm to 300 mm 7.0 µm
as per IS 2921:2016 300 mm to 500 mm 7.9 µm
Vernier Height Gauges
6 Feeler Gauge WAGA/CM/043 0.05 mm to 1 mm 2.7 µm
Using micrometer as per
Linear measurement by
direct comparison
7 Test sieve WAGA/CM/048 20 µm – 100 mm 3.1 µm
Using vision measuring
system as per
ASTM E 11-22 Standard
specification for wire cloth
and sieves for testing
purposes -
8 Shrinkage Ruler WAGA/CM/053 1 mm to 600 mm 0.013 mm
Using ruler compactor as
Per the ISO 3759:2011
Determination
of dimensional change
0.1 inch to 18 inch 0.037 inch

Dealing Officer
Page 13 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (Laboratory based)

9 Shrinkage template WAGA/CM/053 1 mm to 600 mm 0.87 mm

Using Steel ruler as per the
ISO-3759: 2011 0.1 inch to 18 inch 0.037 inch
Determination of
dimensional change
Group: Pressure & Vacuum
1 Pressure Gauges / WAGA/CM/011 and 0 to 40 bar 0.024 bar
Pressure Transmitters WAGA/CM/021 0 to 700 bar 0.12 bar
with/Without Using Digital Pressure 0 to 1000 bar 0.27 bar
Indicator / Pressure Transducer and Digital
Transducers with/ Multimeter by Direct /
Without Indicator Comparison Method based
(Pneumatic / on DKD-R6-1:2014
Hydraulic)
2 Differential Pressure WAGA/CM/011 and -0.75 mbar to 0 mbar 0.23 mbar
Gauges / Pressure WAGA/CM/021
Transmitters with/ Using Digital Pressure 0 mbar to 75 mbar 0.24 mbar
WithoutIndicator / Transducer and Digital
Pressure Transducers Multimeter by Direct /
with/ Without Comparison Method based
Indicator on DKD-R6-1-2014

Dealing Officer
Page 14 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (Laboratory based)

Group: Mass
Weights WAGA/CM/003
1 F2 class & Coarser 1g 0.1 mg
Using E1, E2,F1 class
weights as per double 2g 0.1 mg
substitution method (ABBA)
OIML R 111:2004 and MSL 5g 0.1 mg
Technical Guide 7 10 g 0.1 mg
20 g 0.1 mg
50 g 0.1 mg
100 g 0.1 mg
200 g 0.1 mg
10 mg
M3 Class & Coarser 500 g
M1 Class & Coarser 10 mg
1000 g
F2 Class & Coarser 10 mg
2000 g
F2 Class & Coarser 10 mg
5000 g
F2 Class & Coarser 10 mg
10 kg
M1 Class & coarser 0.20 g
20 kg

Dealing Officer
Page 15 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (Laboratory based)

Group: Volume

1 Laboratory glassware - WAGA/CM/038 0 to 10 ml 0.003 ml

One-mark pipette Using standard balance as 10 to 100 ml 0.009 ml
Graduated pipette per ISO 4787:2021
Burette Volumetric Flask Laboratory glassware- 1000 to 2000 ml 0.65 ml
Graduated measuring Volumetric instruments-
cylinder methods for testing of
Graduated beaker capacity and for use
Conical flask
2 Piston operated WAGA/CM/222
volumetricapparatus - Using standard balance as 200 μl to 100 ml 0.61 μl
Micropipette , piston per ISO 8655-6:2022
operated dispensers Piston- operated volumetric
apparatus —Part 6:
Gravimetric reference
measurement procedure for
the determination of
volume
Group: Force-Torque
1 Torque Generating WAGA/CM/040 0 to 50 Nm 2.1%
Devices Using torque transducer as
50 to 220 Nm 2.4%
per IS 16906:2018
Guidelines on the 220 to 2200 Nm 1.9%
calibration of static torque
measuring device

Dealing Officer
Page 16 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (Laboratory based)

Group: Acceleration and Speed

1 Tachometers WAGA/CM/019 using 60 rpm to 0.35 rpm
multifunction calibrator/ 6000 rpm
tacho- adaptor as per direct 6000 rpm to 0.79 rpm
comparison of Non-Contact
60000 rpm
Type by ElectricalPulse
60000 rpm to 7.1 rpm
100000 rpm
2 Tachometer (Contac WAGA/CM/058 using RPM 10 rpm to 2.6 rpm
type) calibrator as per direct 10000 rpm
comparison
3 Rotating Machines WAGA/CM/018 using 6 rpm to 1000 rpm 0.99 rpm
(includingcentrifuges) tachometeras per the direct 1000 rpm to 1.9 rpm
measurement ofthe speed 20,000 rpm

Dealing Officer
Page 17 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (At Site)

Group: Dimension
1 Shrinkage Ruler/ WAGA/CM/053 1 mm to 600 mm 0.87 mm
Shrinkagetemplate Using Steel ruler as per the
ISO-3759:2011 0.1 inch to 18 inch 0.037 inch
Determination of
dimensional change

Group: Pressure & Vacuum

1 Pressure Gauges / WAGA/CM/011 and 0 to 40 bar 0.024 bar
Pressure Transmitters WAGA/CM/021
0 to 700 bar 0.12 bar
with/Without Indicator Using Digital Pressure
/ Pressure Transducers Transducer and Digital 0 to 1000 bar 0.27 bar
with/Without Indicator Multimeter by Direct /
(Pneumatic / Hydraulic) Comparison Method based
on DKD-R6-1:2014

2 Differential Pressure WAGA/CM/011 -0.75 mbar to 0 mbar 0.23 mbar

Gauges / Pressure Using Digital Pressure
Transmitters with/ Transducer by Direct / 0 mbar to 75 mbar 0.24 mbar
WithoutIndicator / Comparison Method based
Pressure Transducers on DKD-R6-1:2014
with/ WithoutIndicator

Dealing Officer
Page 18 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Group: Mass
1 Analytical balances, WAGA/CM/004 0 to 50 g 0.01 mg
Digitalelectronic top Using, E1,E2, F1 class d= 0.001 mg &
loading balances, weights as per the MSL coarser
Technical Guide 25 0 to 200 g 0.03 mg
Analogue top loading
Calibrating Balances & d=0.01 mg &
balances OIML R 76:2006 coarser
0 g to 1000 g 3.6 mg
d= 1 mg & coarser
0 to 30 kg 0.12 g
d= 10 mg & coarser
0 to 50 kg 0.63 g
d=1 g and coarser
2 Weighing Scales WAGA/CM/044 using 0 kg to 100 kg 0.72 g
standard F1, M1 class 100 kg to 200 kg 14 g
weight set as per 200 kg to 500 kg 20 g
Linearity check with
conventional mass values
Group: Force
1. Uniaxial force testing WAGA/CM/012 100 N to 100 kN 0.6 to 2.0 %
machine using 0.5 &1 load cell as per
the Measurement of static
force in tensile and
compression modes as per
the ISO 7500-1:2018
Measurement of staticforce 100 kN to 2000 kN 0.3 to 0.5 %
in compression modes as
per the ISO 7500-1:2018

Dealing Officer
Page 19 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Mechanical Calibration (At Site)

Group: Acceleration and Speed

1 Rotating Machines WAGA/CM/018 using 6 rpm to 1000 rpm 0.65 rpm

(includingcentrifuges) tachometeras per the direct
measurement ofthe speed
1000 rpm to 1.3 rpm
20,000 rpm

Dealing Officer
Page 20 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Optical & Photometry Calibration (Laboratory based)

Group: Illuminance
1 Illuminance Meters WAGA/CM/039 using lux 2 to 10 Lux 5.6 %
measuring system as per 10 Lux to 10000 Lux 3.7 %.
direct comparison of 10000 Lux to 7.3 %
Illuminance measurement 20000 Lux
2 Color assessment WAGA/CM/002 using D65 6200 - 6800 K 68 K
cabinet Spectro radiometer direct
CWF 3700-4430 K 45 K
measurement of
Colour temperature/ Inca A 2600-3150 K 32 K
illuminance
T84 2700-4300 K 43 K
U35 3200-3800 K 38 K
D65 6200 - 6800 K 68 K
with
UV
U30 2700-3300 K 33 K
TL 83 2700-3300 K 33 K
F 2600-2800 K 28 K
D50 4703-5303 K 54 K

Dealing Officer
Page 21 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Optical & Photometry Calibration (Laboratory based)

Illuminance D65 900 - 2600 Lx 31 Lx

CWF 1200– 3100 37 Lx
Lx
Inca A 900 -2850 Lx 35 Lx
TL84 1600-3900 Lx 47 Lx
U35 2200-3400 Lx 41 Lx
Horiz 500-1700 Lx 21 Lx
on
D65 900 - 2600 Lx 31 Lx
with
UV
U30 1700-3700 Lx 45 Lx
TL 83 1700-3700 Lx 45 Lx
F 400-2300 Lx 28 Lx
D50 1400-3100 Lx 37 Lx

Dealing Officer
Page 22 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Optical & Photometry Calibration (At Site)

Group: Illuminance
1 Color assessment WAGA/CM/002 using D65 6200 - 6800 68 K
cabinet Spectro radiometer direct K
measurement of CWF 3700-4430 K 45 K
Colour temperature/
/illuminance Inca A 2600-3150 K 32 K
T84 2700-4300 K 43 K
U35 3200-3800 K 38 K
D65 6200 - 6800 68 K
with K
UV
U30 2700-3300 K 33 K
TL 83 2700-3300 K 33 K
F 2600-2800 K 28 K
D50 4703-5303 K 54 K
Illuminance D65 900 - 2600 31 Lx
Lx
CWF 1200– 3100 37 Lx
Lx
Inca A 900 -2850 Lx 35 Lx

Dealing Officer
Page 23 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Optical & Photometry Calibration (At Site)

TL84 1600-3900 47 Lx
Lx
U35 2200-3400 41 Lx
Lx
Horizo 500-1700 Lx 21 Lx
n
D65 900 - 2600 31 Lx
with Lx
UV
U30 1700-3700 45 Lx
Lx
TL 83 1700-3700 45 Lx
Lx
F 400-2300 Lx 28 Lx
D50 1400-3100 37 Lx
Lx

Dealing Officer
Page 24 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Thermal Calibration (Laboratory based)

Group: Temperature & Humidity

1 Digital Thermometer WAGA/CM/005 and -30 0C to 150 0C 0.09 0C
with probe, Dial WAGA/CM/029 150 ºC to 600 ºC 0.14 0C
Thermometer using PRT as per Direct
comparison under
controlled conditions
2 Thermocouples WAGA/CM/015 using S type 1500C to 700 0C 1.8 0C
thermocouple as per 700 0C to 1200 0C 2.2 0C
EURAMAT Calibration Guide
No.8 :2020 Guidelines on
the Calibration of
Thermocouples
3 Temperature Enclosures WAGA/CM/020 using t -300C to 300 0C 0.93 0C
–Nine Point thermocouple as per AS
2853:1986 Enclosures-
Temperature-controlled-
performance testing and
grading multipoint
temperature verification
4 Temperature Enclosures WAGA/CM/041 using -30 0C to 300 0C 0.93 0C
–Three Pont thermocoupleas per the
Three-point temperature
verification

Dealing Officer
Page 25 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Thermal Calibration (Laboratory based)

5 Liquid Baths WAGA/CM/042 using 25 0C to 1000C 0.51 0C

PRT/PT100 as per the
Performance verification in
temperature at 5 locations
6 Autoclave WAGA/CM/050 using 20 0C – 140 0C 0.71 0C
temperaturedata logger as
1 min - 60 min 1.3 sec
per Temperature
Measurement Time 0 to 2 bar 0.050 bar
Measurement Pressure
Measurement
7 Muffle/Tube Furnace WAGA/CM/045 using 100 0C to 700 0C 1.7 0C
thermocouple asper 700 0C to 1100 0C 2.2 0C
Temperature verification
8 Hygrometers WAGA/CM/047 using 100C to 45 0C 0.61 0C
standard temperature @ (40 %, 50 %,
/humidity meter as per 60 %)
Direct comparison under 30 % to 90 % 2.7 %
controlled conditions @ (20, 25,30 0C)
Temperature Humidity
9 Humidity Chambers WAGA/CM/016 using 10 0C - 50 0C 0.30 0C
temperature/humidity @ (50 %)
meter as per 10 % - 90 % 1.2 %
IEC 60068-3-6:2018
@ (25%)
Confirmation of the
performance of
temperature/humidity
chambers

Dealing Officer
Page 26 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Thermal Calibration (At Site)

Group: Temperature & Humidity

1 Digital Thermometer WAGA/CM/005 and -30 0C to 150 0C 0 .09 0C
with probe, Dial WAGA/CM/029 using PRT 150 0C to 600 0C 0.14 0C
Thermometer as per Direct comparison
under controlled conditions
2 Muffle/Tube Furnace WAGA/CM/045 using 100 0C to 700 0C 0.23 0C
thermocouple as per 700 0C to 1100 0C 1.4 0C
Temperature verification
3 Temperature Enclosures WAGA/CM/020 using -300C to 300 0C 0.930C
– Nine Point thermocouple as per AS
2853:1986 Enclosures-
Temperature-controlled-
performance testing and
grading Multi point
temperature verification
4 Temperature Enclosures WAGA/CM/041 using -300C to 300 0C 0.93 0C
– Three Pont thermocouple as per the
Three-point temperature
verification
5 Liquid Baths WAGA/CM/042 using 25 0C to 100 0C 0.51 0C
PRT/PT100 as per the
Performance verification in
temperature at 5
location

Dealing Officer
Page 27 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Thermal Calibration (At Site)

6 Humidity Chambers WAGA/CM/016 using 10 0C - 50 0C 0.30 0C

temperature/humidity meter @ 50% RH
as per IEC 60068-3-6:2018
Confirmation of the 10 % - 90 % RH 1.2 %
performance of @ 25 0C
temperature/humidity
chambers
7 Autoclave WAGA/CM/050 using 20 0C – 140 0C 0.71 0C
temperature data logger as
per Temperature 1 min - 60 min 1.3 sec
Measurement
0 to 2 bar 0.050 bar

Dealing Officer
Page 28 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Textile Testing Machinery Calibration (Laboratory based)

Sample cutter
1 Linear measurement WAGA/CM/006 using Vernier 0 to 150 mm 0.015 mm
(Area calculation) caliper
Crock Meter

1 Force measurement WAGA/CM/001 using Load 8 N to 11 N 0.01 N

cell /vernier caliper/
2 Linear measurement 5 mm to 110 mm 0.02 mm
tachometer
(stroke)
5 to 20 mm (peg 0.02 mm
dia.)
3 Speed measurement 10 to 100 rpm 0.90 rpm
Perspiration tester
1 Mass Measurement WAGA/CM/022 using balance 0.4 kg – 6 kg 0.19 g
Moisture Balance
1 Mass Measurement WAGA/CM/065 using E2 1 mg to 100 g 1 mg
weight set/PT100/ stop 100 g to 200 g 6 mg
watch as per MSL Technical
Guide 25
2 Temperature 4 0C to 200 0C 0.54 0C
Measurement

3 Time Measurement 1 min – 30 min 0.6 sec

Dealing Officer
Page 29 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Textile Testing Machinery Calibration (At Site)

Reference washing machines(including wascator)

1 Temperature WAGA/CM/010 using 0 0C to 100 0C 0.54 0C
measurement thermocouple/water level
2 Linear measurement ruler/stop watch/ 50 mm to 200 mm 0.93 mm
3 Time measurement tachometer asper the 1 sec. to 300 min. 0.70 sec
4 Speed measurement 20 rpm to 2500 rpm 0.70 rpm
Tumble Dryers
1 Temperature WAGA/CM/009 using 10 0C to 100 0C 0.54 0C
measurement thermocouple/stop
2 Time measurement watch/tachometer 1 sec to 300 min 0.90 sec
3 Speed measurement 10 rpm to 1000 rpm 0.70 rpm

Pilling & Snagging Tester (Box& Drum)

1 Linear measurement WAGA/CM/008 using 5 mm to 320 mm 0.02 mm
Vernier caliper/
2 Speed measurement 6 rpm to 5000 rpm 0.70 rpm
tachometer/
3 Time measurement stop watchas 1 sec to 45 min 0.91 sec
4 Pressure 0 to 10 bar 0.06 bar
Abrasion Machine (IncludingMartindale)
1 Mass WAGA/CM/007 using 100 g to 3000 g 0.30 g
vernier caliper /tachometer
2 Linear measurement 0.5 mm to 150 mm 0.012 mm
3 Speed measurement 20 rpm to 100 rpm 0.70 rpm

Dealing Officer
Page 30 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Textile Testing Machinery Calibration (At Site)

Colour Fastener Testers

1 Temperature WAGA/CM/032 using 30 0C to 100 0C 0.39 ºC
measurement thermocouple/
/tachometer/stopwatch/
vernier caliper
2 Speed 30 rpm to 100 rpm 0.7 rpm

3 Time 15 min to 90 min 0.7 sec

4 Volume 500 ml to 1500 ml 2.0 ml

Heat Transfer Press Machines

1 Direct Measurement WAGA/CM/031 using 100 0C to 200 0C 0.15 0C
Temperature thermocouple/ /pressure
gauge/stop watch

2 Pressure 0 bar to 20 bar 0.01 bar

3 Time 5 sec to 30 sec 0.6 sec

Sample cutter
1 Linear measurement WAGA/CM/006 using 0 to 150 mm 0.015 mm
(Area calculation) vernier caliper as per

Dealing Officer
Page 31 of 32
 FEDERATION FOR DEVELOPMENT OF ACCREDITATION SERVICES
118-119, First Floor, Sushant Tower, Sector – 56, Gurugram – 122011, Haryana, India.

SCOPE OF ACCREDITATION
(Annexure to Certificate of CL - 123)
Laboratory Name: M/s WAGA Calibration Services Pvt. Ltd.
173, High Level Road, Maharagama, Sri Lanka

Validity: 04.05.2024 to 03.05.2026 Amended on N/A

S.No. Parameter Calibration Method/ Range Uncertainty in

Procedure & Equipment Measurement (±) *
used as Reference
Standard

Textile Testing Machinery Calibration (At Site)

Crock Meter
1 Force measurement WAGA/CM/001 using Load 8 N to 11 N 0.01 N
2 Linear measurement as cell/vernier caliper/ 5 mm to 110 mm 0.02 mm
per the tachometer (stroke)
5 to 20 mm 0.02 mm
(peg dia.)

3 Speed measurement 10 to 100 rpm 0.90 rpm

Perspiration Tester
1 Mass Measurement WAGA/CM/022 using 0.4 kg – 6 kg 0.19 g
balanceas

Moisture Balance
1 Mass Measurement WAGA/CM/065 using E2 1 mg to 100 g 1 mg
weight set/PT100/ stop 100 g to 200 g 6 mg
2 Temperature watch as per MSL Technical 4 0C to 200 0C 0.54 0C
Measurement Guide 25
3 Time Measurement 1 min – 30 min 0.6 sec

Dealing Officer
Page 32 of 32