• Data Rate up to 20 Kbits/S • 433.92 MHz Operation • 2 Selectable RF Channels (433.92 / 434.33 MHz) • Narrowband Crystal Controlled • Wide Supply Range • Optimal Range 200m
Applications
• Alarm and Security Systems
• Home Automation • Remote Controls • Sensor Reporting • Wireless Communication
General Description
The RXQ1 is a half duplex radio transceiver Its unique features of channel selection and module for use in bi-directional data transfer interference rejection make the RXQ1 ideal to applications at ranges up to 200 meters. provide a reliable wireless link. The module operates in the 433MHz European The RXQ1 modules will suit one-to-one multi-node ISM (Industrial, Scientific and Medical) Frequency wireless links in applications including building Band. and car security, remote industrial process monitoring and computer networking. The RXQ1 radio transceiver contains two RF channels at 433.92 and 434.33MHz selectable by Because of its small size and low power external pin (CS pin). requirements, the module is ideal for use in portable wireless applications. The module uses a ‘crystal controlled’ design providing narrow band performance, much better than other wideband ‘SAW’ based designs. Absolute Maximum Ratings
Supply Voltage (Vcc) ................ -0.3V to + 6V Operating Temperature ............ -20°C to +70°C Input Voltage ............................ -0.3V to Vcc + 0.3V Storage Temperature ............... -40°C to +100°C Output Voltage ......................... -0.3V to Vcc + 0.3V
Electrical Characteristics Ta = 25°C unless otherwise specified
CHARACTERISTICS MIN TYP MAX UNIT
VCC Supply Voltage 2.7 3 5.25 VDC ISR Supply Current (Receive mode) 12 mA IST Supply Current (Transmit mode) 26 mA ISS Supply Current (Standby mode) 8 uA VOH High-Level Output Voltage (I=-1mA) 0.7 VCC VCC V VOL Low-Level Output Voltage (I=1mA) 0 0.3 VCC V Working Frequency 433.92 / 434.33 MHz Receiver Sensitivity -100 dBm FM Deviation ±15 KHz BWIF IF Bandwidth 65 85 KHz RF Output Power into 50Ω +5 dBm Harmonic Spurious Emission -50 dBc Data bit Rate 0 20 Kbit/s TOP Operating Temperature Range -20 +70 °C
Timing Data CHARACTERISTICS MIN TYP MAX UNIT Power Up to Stable receiver Data out 5 mS Power Up to Full RFout 4 mS Standby to RX mode 3 mS Standby to TX mode 2 mS Switching from TX to RX mode 3 mS Switching from RX to TX mode 1 mS
RF ground pin. For best results, these pins should be Active low transmit select. connected to the ground plane against which the antenna radiates. RX Select (pin 16) Active low receive select. Antenna (pin 2) Nominal 50 ohm input/output impedance capacitively Vcc (pin 17) isolated from the internal circuit. Supply voltage range from 2.7 to 5.25 volts.
GND (pins 5, 9, 10)
Channel Select (pin 18) Supply ground connections. Data 0 selects 433.92MHz. Data 1 selects 434.33MHz. NC (pins 4, 6, 7, 8, 11, 13) Not connected TX Selext RX Select Function RXD (pin 12) Receiver digital data output (CMOS logic out) 0 0 Power Down Mode representing true data as supplied to the transmitter. 0 1 Transmit Mode TXD (pin 14) 1 0 Receive Mode Data input to the transmitter can be directly interfaced to 1 1 Power Down Mode CMOS logic drive operating on the same supply voltage as the transceiver.
pag.3 telecontrolli HEAD OFFICE & PLANT Via Naz. delle Puglie, 177 80026 CASORIA (NA), Italy Tel: +39 081 7599033 Fax: +39 081 7596494
