Amarex KRT

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

Type series booklet

2553.5/ 9--EN Amarex KRT


Submersible motor pumps DN 40 to DN 700

Cast iron and various materials for industrial effluents

50 Hz
standard range

Stationary installation
Transportable installation
Dry-installed
Other versions on request

Automation products available:


• PumpExpert
• Hyamaster
• hyatronic
• LevelControl Basic 2

Applications Shaft sealing


Amarex submersible motor pumps are used for pumping all 2 mechanical seals being independent of the direction of
types of sewage and effluent in water treatment and industry, rotation, lubricated with non-toxic oil
especially untreated sewage with long fibrous and solid
substances, liquids containing air and gas as well as raw,
activated and digested sludge. Bearings
grease lubricated ball bearings
Operating data
Capacity Q up to 10 000 m3/h, 2 778 l/s Designation
Head H up to 100 m Example
Motor power P2 from 0.8 kW to 850 kW KRT K 150-500 / 80 4 UN G -- D
Temperature of Pump type
pumped liquid t up to 60 oC Impeller type
Enclosure type IP 68 to IEC 60034--5 S, F, E, D, K
additional flameproof versions ATEX II 2G T3 or T4 Hydraulics dimension
Motor size
Drive Number of poles
Three-phase asynchronous motor Motor version
400 V (variants: 230 V, 380 V, 415 V, 500 V, 690 V) U, UN, UK, W, WN, X, XN, XK, Y, YN
Material version / variant
Material G, G1, G2, GH, H, C1, C2
Standard version of cast iron Installation Type
S, P, K, D, H
Material variants of wear-resistant chilled iron and
corrosion-resistant duplex stainless steel

New:
Motor versions with energy- saving motors IE2 - High Efficiency or
IE3 - Premium Efficiency
(classification to EN 60034- 30 based on EC Directive 640/2009 for
standardised motors)
Amarex KRT

Contents
Page

Product advantages 3

Impeller Types 4

Guide to material and hydraulics selection for individual pumped liquids 5

Selection Diagrams 50 Hz 6--9

Guarantee, Tests / Inspections and Quality Assurance 9

Technical Data 10--12

Installation Types 13

Materials 14

TECHNICAL DATA -- STANDARD PROGRAMME / (standard variants) 15--16

Typical sectional drawing 17--18

Shaft Seal 19

2
Amarex KRT

Product advantages
Example: Amarex KRT K 100-250/7 4WG

Absolutely water--tight Reliability


Even in the event of power cable Motors specially developed for
damage, no fluid can penetrate submersible motor pumps offer
into the motor. maximum operating safety.

K E

Variable hydraulic system


The right impeller with optimum
efficiency for every fluid. Long service life
High operating reliability due to 2 bi--rotational mechanical seals
wide free passages.

3
Amarex KRT

Impeller Types
KRT K 150-315 / 12 6 U G -- S
S, F, E, D, K

S D

Impeller with cutting device Open single vane impeller

S-Impeller D-Impeller
for handling domestic sewage with coarse for sewage containing solid
and / or long fibrous matter substances, long fibres and coarse dirt.
F domestic sewage
F dirty water F raw sewage
F faeces F mixed water
F raw and digested sludge
F activated sludge
F circulated and heated sludge

F K

Closed non-clogging 2 or 3 canal


Vortex impeller impeller

F-Impeller K-Impeller
or liquids containing long fibres, solid for contaminated liquids containing
substances, coarse dirt as well as gas sludges and solids which are
or air. non-gaseous and not containing fibres
liable to twist or bunch.
F raw sewage
F activated sludge F screened sewage
F circulated and heated sludge F mechanically treated sewage
F raw and digested sludge F industrial waste water
F mixed water F effluent from waste disposal sites
F storm water
F activated sludge
F industrial effluent

Single vane impeller

! !
Hydraulic systems with S-, D-, F- and E-impellers
E-Impeller are available only as shown in the documented
for sewage containing long fibres and QH parameters.
solid substances. K-impellers can be adjusted to the required duty
F raw sewage point.
F mixed water
F raw and digested sludge
F activated sludge
F circulated and heated sludge

4
Amarex KRT

Guide to material and hydraulics selection for individual pumped liquids


The table below is intended as a guide for selecting pump materials and hydraulics and is based on many years of KSB experience.
The data given in the table is intended as a recommendation / guide only. For more detailed information, please consult your
nearest KSB sales office or ask for expert advice from the KSB advisory departments. Take advantage of the extensive KSB
laboratory know-how when selecting pump materials.
Recommended Suggested
Pumped liquid Comments and recommendations
material impeller type
Dirty water
River water K, D, E, F free p
passage
g >solids in pumped
p p liquid,
q possibly
p y pre-screened
p
Storm water
Waste water
ATV recommendation: free passage of 100 mm,
-- untreated municipal sewage F, S, D, E, K
min 76 mm (3”)
-- containing gas and air F up to 8 %, consult KSB when pumping highly gaseous liquids.
Sludges
-- raw sludge F, D, E
can be pumped with a solids content :
-- digested sludge F, D, E
13 % (D), 8 % (F), 6 % (E), 5 % (K)
-- activated sludge D, K
Industrial effluent contaminated with ...
-- paint suspension K solvent-free; refer to operator instruction
-- varnish suspension F, E solvent-free; consult KSB for silicone-free version
-- fibrous substances F, S, D
st Irron
n

-- filings / chippings K, F G2 or GH variant, special mechanical seal


-- abrasive substances K, F Solids content <5 g/l
ast

Industrial effluent, slightly acid K, F ph-value <5.5 C1 variant and FPM (Viton) O-rings
Ca

Waste water, chemically neutral in respect of corrosion


-- ammonia water K
-- ammonia hydroxide 5 % NH4OH K
-- urea 25 % (NH2)2-CO K
-- potassium hydroxide 10 % KOH K
-- calcium hydroxide 5 % Ca(OH)2 K
-- sodium hydroxide 5 % NaOH K
-- sodium carbonate 30 % Na2CO3 K
Waste water, chemically neutral in respect of corrosion, contaminated with ...
-- aliphatic hydrocarbons,
K
e.g. oils, petrol, butane, methane
-- aromatic hydrocarbons,
K
e.g. benzene, styrene
-- chlorinated hydrocarbons, FPM (Viton) O-rings, for high concentrations consult KSB
e.g. trichloroethylene, ethylene chloride, K
chloroform, methylene chloride
Highly abrasive industrial waste water (chemically neutral)
A sinter content of <5 g/l requires GH design
-- sinter water K
on

A sinter content of >5 g/l requires H design


ed iro

-- lime-milk with quartz and pigment up to 15% lime-milk requires GH design


K
suspension >15% lime-milk requires H design
Chille

-- wash water containing solids K, F


material variant depends on liquid analysis
Ch

-- waste water containing dust / ash K


up to 5 g/l solids content requires GH variant -- above 5 g/l:
Water-sand mixture K, F
H variant

Sea water K, F C2-variant


Du x-
Duplex
steel

C1 or G1 (with 250 mm 2-comp. epoxy resin),


Brackish water K, F
-- depending on salt content
s

Corrosive industrial effluent K, F C1 or C2, depending on analysis of pumped media

5
Amarex KRT

Selection Diagrams 50 Hz
S-Impeller
5 US.gpm 10 20 30 40 50 100 200
100 4 5 IM.gpm 10 20 30 40 50 100
300

200
50 40--250/ 2p
40
50--210/ 2p
30 100

20
50
40
10
30

20
5
4

3 10

ft
2
H 5
[m]
4
1
1 Q [m3/h] 2 3 4 5 10 20 30 40 50
0.3 0.4 0.5 1 l/s 2 3 4 5 10

F-Impeller
50 US.gpm 100 200 300 400 500 1000 2000 3000 4000
100 40 50 IM.gpm 100 200 300 400 500 1000 2000 3000
300
80--250/251/ 2p
80--316/ 2p
200
50 40--250/ 2p
100--315/ 4p
40 100--401/ 4p
30 100--240/ 2p 100

20 150--401/ 4p

50
40
40--250/ 4p 80--250/ 4p
10
30
150--401/ 6p
20
5
150--315/ 6p
4

3 10

ft
2
100--250/ 4p
H 5
[m]
4
1
10 Q [m3/h] 20 30 40 50 100 200 300 400 500 1000
3 4 5 l/s 10 20 30 40 50 100 200

6
Amarex KRT

E-Impeller
50 US.gpm 100 200 300 400 500 1000 2000 3000 4000
100 40 50 IM.gpm 100 200 300 400 500 1000 2000 3000
300

200
100--401/ 4p
50
40

30 100
100--315/ 4p 150--401/ 4p

20
80--250/ 4p 200--401/ 4p 50
150--315/ 4p 40
100--250/ 4p
10
30

200--401/ 6p 20
5 150--315/ 6p

3 10
150--401/ 6p
ft
2
H 5
[m]
4
1
10 Q [m3/h] 20 30 40 50 100 200 300 400 500 1000
3 4 5 l/s 10 20 30 40 50 100 200

D-Impeller
200 300 400 500 US.gpm 1000 2000 3000 4000
100 200 300 400 500 IM.gpm 1000 2000 3000 4000
300

80--315/ 2p
200
50
40
100--315/ 2p 150--401/ 4p
30 100

20 150--400/ 4p
80--315/ 4p 200--400/ 4p
100--316/ 4p 50
150--315/ 4p
40
10
100--251/ 4p 30
150--315/ 6p 150--401/ 6p
250--400/ 4p 20
200--315/ 4p
5 150--251/ 4p 200- -400/ 6p
4

3 10

200--315/ 6p 250--400/ 6p 300--400/ 6p ft


2
H 5
[m]
4
1
30 40 50 Q [m3/h] 100 200 300 400 500 1000 2000
10 l/s 20 30 40 50 100 200 300 400 500

7
Amarex KRT

K-Impeller
50 US.gpm 100 200 300 400 500 1000 2000 3000 4000
100 40 50 IM.gpm 100 200 300 400 500 1000 2000 3000
300

200
40--250/ 2p
50
100--400/ 4p
40 100--401/ 4p
30 100
50--210/ 2p 80--251/ 2p
100--315/ 4p
20
50
40
40--250/ 4p 100--250/ 4p
10
30

20
5
4

3 10

50--210/ 4p ft
2
H 5
[m]
4
1
10 Q [m3/h] 20 30 40 50 100 200 300 400 500 1000
3 4 5 l/s 10 20 30 40 50 100 200

K-Impeller
200 300 400 500 1000 2000 3000 4000 US.gpm 10000
100 200 300 400 500 1000 2000 3000 4000 IM.gpm 10000
300

150--500/ 4p 200--500/ 4p 300--503/ 4p 200


50
250--630/ 6p
40 150--401/ 4p 151--401
/ 4p
30 100
200--401
/ 4p 250--401/ 4p
20 300--420/ 4p
150--315/ 4p 200--330/ 4p 50
250--400/ 4p 40
300--500/ 6p
10
30
200--401/ 6p
150--315/ 6p
20
300--400/ 6p
5
250--400/ 6p
4
200--315/ 6p
3 10
ft
2 300--400/ 8p
200--316/ 6p
300--401/ 8p
H 5
[m]
4
1
30 40 50 Q [m3/h] 100 200 300 400 500 1000 2000 3000
10 20 30 40 50 l/s 100 200 300 400 500

8
Amarex KRT

K-Impeller
2000 3000 4000 5000 US.gpm 10000 20000 30000 40000
100 2000 3000 4000 5000 IM.gpm 10000 20000 30000
300

350--710/ 6p 200
50
40 350--630/ 6p
30 350--636/ 6p 700--901/ 8p 100
400--630/ 6p
350--500/ 6p
20
50
350--420/ 6p 500--630/ 6p
40
350--501/ 6p 400--500/ 6p 600--710/ 10p
10
30
700--900/ 10p

350--500 600--520/ 8p
20
/ 8p
5 400--500/ 8p 500--630/ 8p 700--900/ 12p
4

3 400--500/ 10p 10
500--630/ 10p
ft
2
H 5
[m]
4
1
400 500 Q [m3/h] 1000 2000 3000 4000 5000 10000
200 300 400 500 l/s 1000 2000

Guarantee, Tests / Inspections and Quality Assurance


Each pump is subjected to a functional test to KSB standard ZN 56 525. Pump performance is guaranteed to ISO 9906/A.
Acceptance inspections conforming to ISO / DIN or another comparable standard are possible at a surcharge.
The quality is assured under a tested and to DIN EN ISO 9001 certified quality assurance system.

9
Amarex KRT

Technical Data
Cast iron (G, G1, G2, GH)
Pump sizes Material Impeller Dry installation Wet--well installation Moment of
variants (Installation Type “D”, “H”) (Installation Type “S”, “P”, “K”) inertia
Impeller Free D2max D2min max. max. max. max. J
2), 3)
channels passage operating test operating test
pressure 1) pressure pressure 1) pressure
qty. [mm] [mm] [mm] [bar] [bar] [bar] [bar] [kgm2]
S 40–250 G 4 7 225 175 -- -- 10.1 13.1 0.030
F 40–250 G,, G1,, G2,, -- 25 210 150 -- -- 10.0 13.0 0.030
F 80–250 GH 76 265 150 6 9 6.5 8.5 0.140
F 80–251 G -- 50 230 145 -- -- 6.7 8.7 0.057
F 80–316 65 265 200 -- -- 8.1 10.5 0.075
F 100–240 G,, G1,, G2,, -- 100 190 170 -- -- 3.7 4.8 0.130
F 100–250 GH 100 265 200 6 9 3.6 4.7 0.056
F 100–315 100 310 270 -- -- 4.3 5.6 0.056
F 100–401 100 390 325 10 15 9.5 12.4 0.248
F 150–315 120 290 250 6 9 3.5 4.6 0.144
F 150–401 135 390 270 10 15 9.1 11.8 0.248
E 80–250 G 1 76 270 225 6 9 6.5 8.5 0.17
E 100–250 90 245 202 6 9 3.6 4.7 0.16
E 100–315 100 330 262 -- 4.3 5.6 0.26
E 100–401 80 412 389 -- -- 9.5 12.4 0.60
E 150–315 110 320 254 6 9 3.5 4.6 0.31
E 150–401 115 407 348 10 15 9.1 11.8 0.68
E 200–401 120 400 319 10 15 7.2 9.4 0.86
D 80--315 G,, G1 1 65 265 234 10 15 10.6 13.8 0.124
D 100--251 76 265 234 6 9 3.5 4.6 0.115
D 100--315 75 222 196 -- -- 6.8 8.8 0.065
D 100--316 85 306 270 -- -- 3.6 4.7 0.233
D 150--251 100 254 225 6 9 1.9 2.5 0.115
D 150–315 100 317 280 6 9 3.3 4.3 0.289
D 150--400 100 363 326 -- -- 5.2 6.8 0.573
D 150--401 110 384 370 -- -- 5.4 7.0 0.999
D 200–315 100 315 280 6 9 2.7 3.5 0.261
D 200–400 100 375 365 -- -- 3.4 4.4 0.825
D 250–400 120 375 320 -- -- 3.6 4.7 0.653
D 300–400 150 408 375 -- -- 1.7 2.2 0.925
K 40–250 G, G1, GH 3 15 260 150 -- -- 10.0 13.0 0.047
K 80–251 G 3 33 220 140 -- -- 6.7 8.7 0.150
K 100–250 G,, G1,, GH 2 71 256 210 6 9 3.6 4.7 0.070
K 100–315 80 312 254 -- -- 4.3 5.6 0.150
K 100–400 G 2 76 408 350 -- -- 9.5 12.4 1.100
K 100–401 G,, G1,, GH 2 50 404 310 10 15 9.5 12.4 0.504
K 150–315 76 310 235 6 9 3.5 4.6 0.180
K 150–401 76 404 330 10 15 9.1 11.8 0.916
K 151–401 3 80 404 320 10 15 8.8 11.4 0.520
K 150–500 G, G1 3 60 460 420 10 15 9.0 11.7 0.710
K 200–315 G,, G1,, GH 3 70 295 245 6 9 1.9 2.5 0.22
K 200–316 2 100 305 265 6 9 1.7 2.2 0.22
K 200–330 3 70 326 287 10 15 5.5 7.2 0.35
K 200–401 80 404 330 10 15 7.2 9.4 0.52
K 200–500 G,, G1 3 76 504 400 10 15 10.0 13.0 0.83
K 200--501 2 105 502 450 10 15 6.5 8.5 1.68
K 200--631 105 622 540 10 15 10.0 13.0 4.41
K 250–400 G,, G1,, GH 3 85 370 300 10 15 7.0 9.1 0.50
K 250–401 2 105 400 310 10 15 6.0 7.8 0.55
K 250--630 G, G1 3 90 630 500 10 15 10.5 13.7 2.76
K 300–400 G,, G1,, GH 3 100 408 332 10 15 3.6 4.7 0.75
K 300–401 2 135 408 367 10 15 2.3 3.0 0.75
1) zulässiger Betriebsdruck = Zulaufdruck + Druck bei Q = 0
2) Values for biggest impeller diameter
3) Impeller with water fill

10
Amarex KRT

Cast iron (G, G1, G2, GH)


Pump sizes Material Impeller Dry installation Wet--well installation Moment of
variants (Installation Type “D”, “H”) (Installation Type “S”, “P”, “K”) inertia
Impeller Free D2max D2min max. max. max. max. J
2), 3)
channels passage operating test operating test
pressure 1) pressure pressure 1) pressure
qty. [mm] [mm] [mm] [bar] [bar] [bar] [bar] [kgm2]
K 300–420 G,, G1 3 100 408 370 6 9 5.6 7.3 0.95
K 300–500 90 504 430 10 15 4.5 5.9 1.48
K 300–503 5 50 480 405 10 15 9.2 12.0 2.50
K 350–420 3 100 450 387 6 9 3.6 4.7 1.22
K 350–500 110 508 426 6 9 5.8 7.5 3.12
K 350–501 2 170 509 495 6 9 2.8 3.6 3.00
K 350–630 3 135 630 500 10 15 7.5 9.8 5.22
K 350–636 5 75 630 510 10 15 6.5 8.5 5.42
K 350–710 3 110 730 560 10 15 9.0 11.7 10.60
K 400--500 130 508 443 6 9 3.6 4.7 3.37
K 400--630 132 620 546 6 9 6.3 8.2 8.21
K 500–630 133 582 520 4 6 4.5 5.9 6.11
K 600--520 145 532 457 4 6 2.5 3.3 7.02
K 600--710 165 736 685 4 6 4.3 5.6 17,0
K 700--900 190 850 738 3 4.5 3.4 4.4 40.0
K 700--901 180 908 760 9 13.5 7.5 9.8 50.0
1) Allow. operating pressure = inlet pressure + pressure at Q = 0
2) Values for biggest impeller diameter
3) Impeller with water fill

Industrial materials (H, C1, C2)


Pump sizes Material Impeller Dry installation Wet--well installation Moment of
variants (Installation Type “D”, “H”) (Installation Type “S”, “P”, “K”) inertia
Impeller Free D2max D2min max. max. max. max. J
2), 3)
channels passage operating test operating test
pressure1) pressure pressure1) pressure
qty. [mm] [mm] [mm] [bar] [bar] [bar] [bar] [kgm2]
S 50–210 C1, C2 4 7 185 170 -- -- 4.3 5.6 0.006
F 40–250 H,, C1,, C2 -- 25 210 150 -- -- 10.0 13.0 0.030
F 50–210 40 190 170 -- -- 3.6 4.7 0.008
F 65–210 65 195 115 -- -- 2.1 2.7 0.014
F 80–210 80 210 158 -- -- 1.4 1.8 0.027
F 80–250 76 265 190 6 9 6.5 8.5 0.140
F 100–240 100 190 170 -- -- 3.7 4.8 0.130
F 100–250 100 265 200 6 9 3.6 4.7 0.056
F 100–315 100 310 270 -- -- 4.3 5.6 0.056
F 100–401 100 390 325 10 15 9.5 12.4 0.248
F 150–315 120 290 250 6 9 3.5 4.6 0.144
F 150–401 135 390 270 10 15 9.1 11.8 0.248
K 50--210 C1, C2 5 7 208 130 -- -- 3.6 4.7 0.025
K 40–250 H,, C1,, C2 3 15 260 150 -- -- 10.0 13.0 0.047
K 80–251 33 220 140 -- -- 6.7 8.7 0.150
K 100–250 2 71 256 210 6 9 3.6 4.7 0.070
K 100–315 80 312 254 -- -- 4.3 5.6 0.150
K 100–401 50 404 310 10 15 9.5 12.4 0.504
K 150–315 76 310 235 6 9 3.5 4.6 0.180
K 150–401 76 404 330 10 15 9.1 11.8 0.916
K 151–401 3 80 404 320 10 15 8.8 11.4 0.520
K 200–315 70 295 245 6 9 1.9 2.5 0.22
K 200–316 2 100 305 265 6 9 1.7 2.2 0.22
K 200–330 3 70 326 287 10 15 5.5 7.2 0.35
K 200–401 80 404 330 10 15 7.2 9.4 0.52
K 250–400 3 85 370 300 10 15 7.0 9.1 0.50
K 250–401 2 105 400 310 10 15 6.0 7.8 0.55
K 300–400 3 100 408 332 10 15 3.6 4.7 0.75
K 300–401 2 135 408 367 10 15 2.3 3.0 0.75
1) Allow. operating pressure = inlet pressure + pressure at Q = 0
2) Values for biggest impeller diameter
3) Impeller with water fill

11
Amarex KRT

Moment of inertia (Rotors)


Motor sizes Moment of Motor sizes Moment of Motor sizes Moment of Motor sizes Moment of Motor sizes Moment of
inertia inertia inertia inertia inertia
J J J J J
[kgm2] [kgm2] [kgm2] [kgm2] [kgm2]
52 0.01 44/54 0.01 46 0.02 10 8 0.09 40 10.N.. 1.75
52 0.01 74 0.02 66 0.02 17 8 0.12 60 10.N.. 1.93
82 0.01 11 4 0.04 96 0.05 21 8 0.18 75 10.N.. 2.20
12 2 0.02 16 4 0.05 12 6 0.07 26 8.N.. 0.37 90 10.N.. 2.49
17 2 0.03 4 4.KG / 5 4.KG 0.05 4 6.KG 0.07 35 8.N.. 0.47 110 10.N.. 7.96
22 2 / 25 2 0.04 7 4.KG 0.06 6 6.KG 0.09 26 8.N.. 0.40 150 10.N.. 9.66
23 2 0.05 19 4 / 21 4 0.06 19 6 0.09 35 8.N.. 0.50 190 10.N.. 11.8
37 2 0.13 23 4 0.07 20 6 0.10 50 8.N.. 0.66 230 10.N.. 17.7
55 2 0.14 29 4 0.11 26 6 0.13 75 8.N.. 0.94 270 10.N.. 20.5
35 4.N.. 0.22 32 6 0.34 90 8.N.. 1.98 310 10.N.. 23.2
50 4.N.. 0.25 40 6 0.42 110 8.N.. 2.25 350 10.N.. 25.8
65 4.N.. 0.30 50 6 0.51 130 8.N.. 2.55 390 10.N.. 36.1
35 4.N.. 0.25 32 6.N.. 0.37 150 8.N.. 7.30 430 10.N.. 41.6
50 4.N.. 0.28 40 6.N.. 0.45 185 8.N.. 8.57 475 10.N.. 47.2
65 4.N.. 0.33 50 6.N.. 0.54 220 8.N.. 9.84 535 10.N.. 52.7
80 4.N.. 0.46 60 6.N.. 0.66 260 8.N.. 13.3 600 10.N.. 58.2
95 4.N.. 0.55 80 6.N.. 0.80 300 8.N.. 15.9 660 10.N.. 63.7
110 4.N.. 0.63 100 6.N.. 0.94 350 8.N.. 19.1
130 4.N.. 1.26 120 6.N.. 1.89 400 8.N.. 20.7
155 4.N.. 1.43 140 6.N.. 2.25 460 8.N.. 31.5
175 4.N.. 1.57 165 6.N.. 2.55 530 8.N.. 36.3
200 4.N.. 3.78 190 6.N.. 7.30 580 8.N.. 41.1 105 12.N.. 7.96
250 4.N.. 4.13 225 6.N.. 8.57 630 8.N.. 45.8 135 12.N.. 9.66
300 4.N.. 4.82 260 6.N.. 9.84 690 8.N.. 50.6 165 12.N.. 11.8
350 4.N.. 5.51 320 6.N.. 14.3 760 8.N.. 55.3 195 12.N.. 17.7
260 6.N.. 15.9 203 12.N.. 20.5
400 6.N.. 17.6 265 12.N.. 23.2
440 6.N.. 19.2 290 12.N.. 36.1
480 6.N.. 20.7 300 12.N.. 25.8
530 6.N.. 31.5 340 12.N.. 41.6
580 6.N.. 36.3 380 12.N.. 47.2
630 6.N.. 41.1 450 12.N.. 52.7
690 6.N.. 45.8 490 12.N.. 58.2
770 6.N.. 50.6 560 12.N.. 63.7
850 6.N.. 55.3

12
Amarex KRT

Installation Types
KRT K 150-500 / 80 4 UN G -- D
S, P, K, D, H

Stationary wet--well installation (S1 operation with motor submerged )


S
-- with guide wire or guide rails

P Transportable wet--well installation (S1 operation with motor submerged )

Stationary wet--well installation (S1 operation with motor outside the fluid)
K
-- with guide wire or guide rails

D Stationary dry installation, vertical (S1 operation)

H Stationary dry installation, horizontal (S1 operation)

13
Amarex KRT

Materials
Material variants
Material version
Component G G1 G2 GH H C1 C2
Pump unit
Pump casing JL 1040 JN 3029 1.4517
Wear Plate (for D-impeller) JL 1040 --
Casing wear ring JL 1040 VG 434
(for E and K impeller)
Impeller
JL 1040
(D-impeller JL 1040, 1.4517 JN 3029 1.4517
JS 1030
with hardened edges)
Intermediate casing / discharge cover JL 1040 JN 3029 1.4517
Mechanical seal (pump side) SiC / SiC
Mechanical seal (motor side) Carbon / SiC
Shaft 1.4021 / C45+N 1.4021 / 1.4462 / C45+N
(see table, page 15) (see table, page 16)
Bearing bracket JL 1040 1.4517
Motor housing JL 1040 / 1.0038 1.4517
Motor housing cover JL 1040 1.4571 1.4462
Elastomer components Nitrile rubber (NBR) Viton (FPM)
Bolts A4 (equivalent to 1.4571) 1.4462
Cooling jacket 1.4571 / 1.0038 --
Installation parts
Duckfoot bend JL 1040 JN 3029 1.4517
Claw JL 1040 or JS 1030 / JS 1050 1.4517
Mounting bracket 1.4571 up to DN 200; 1.0038 + Z from pump size 200-500 1.4571
Clamp 1.4571 up to DN 200; JL 1040 from pump size 200-500 1.4571
Guide wire 1.4401 1.4401 / Tefzel
Foot plate / feet 1.0038 + Z 1.4571 1.4517 / or 1.4462
Lifting chain / lifting rope chain: 1.0038 + Z / 1.4401 / rope: Polyamid / rope: Polypropylene rope: Polypropylene

Materials -- Information
Cast Iron Duplex Steel Wear resistant White Iron
JL 1040 (GG-25) Cast Stainless Steel (JN3 029 or a technically
Lamellar Graphite Cast Iron (1.4517 or a technically equivalent material)
equivalent material)

This graphited cast iron to DIN 1691 is The resistance to pitting of this ferritic-austenitic A wear resistant white iron for highly
mostly used in the pumping of municipal stainless cast steel makes it particularly suitable abrasive media, such as liquids
sewage, sludges and rain- or surface to pump sewage containing substantial containing sand, ashes or scale.
water. Suitable for neutral, slightly amounts of chlorides and acids or sea- and Its hardness is approximately 61.5
aggressive media and media unlikely to brackish water. Its good chemical resistance, to 68 Rockwell and therefore higher than
cause excessive wear. even against sewage containing phosphorus hardened chromium steel. The alloyed
The pH value of the pumped medium and sulphuric acid, has ensured its wide cast iron of chromium- molybdenum has
should be ≥6.5, sand content ≤0.5 g/l. application in the chemical and process a significantly higher resistance to wear
industries. Pumps made from duplex steel have than cast iron JL 1040 (GG-25) or other
been used very successfully to pump brine, cast materials.
chemical effluents (pH 1 -- 12), foul water and
seepage from waste disposal sites.

Material comparison
EN DIN ASTM equivalent EN DIN ASTM equivalent
JL 1040 GG-25 A 48 Class 40 B 1.0038 ST steel
JN 3029 0.9635 A 532 II C 15 % CrMo-Hc 1.0038 + Z ST TZN galv. steel
1.4517 1.4517 A 890 CD 4 MCu NBR NBR NBR
1.4021 1.4021 A 276 Type 420 FPM FPM FKM
1.4401 1.4401 A 276 Type 316 JS 1030 GGG--40 A 536: 60--40--18
1.4462 1.4462 A 182 F51 JS 1050 GGG--50 A 536: 60--45--12
1.4571 1.4571 A 276 Type 316 Ti VG 434 VG 434 AISI 329
C45+N C 45 N A 576 Gr. 1045

14
Amarex KRT

TECHNICAL DATA -- STANDARD PROGRAMME / (standard variants)


Material variants G, G1, G2, GH
Motor size
2-polig 5 2 ... 25 2 37 2 ... 55 2 -- -- --
95 4N ... 175 4N
4-polig 4 4 ... 29 4 35 4 ... 65 4 35 4N ... 80 4N 200 4N ... 350 4 N --
80 6N ... 165 6N
6-polig 4 6 ... 19 6 32 6 ... 50 6 32 6N ... 60 6N 190 6N ... 480 6N 530 6N ... 850 6N
75 8N ... 130 8N
8-polig -- 26 8, 35 8 26 8N ... 50 8N 150 8N ... 400 8N 460 8N ... 760 8N
40 10N ... 80 10N
10-polig -- -- -- 110 10N ... 350 10N 390 10N ... 660 10N
--
12-polig -- -- -- 105 12N ... 300 12N 340 12N ... 560 12N
Shaft material 1.4021 C45+N 1.4021
Shaft prot. sleeve -- 1.4021
Bearings rolling ele- rolling element pump side:
ment with with lifetime lubrication1) rolling element bearings with re--lubrication facility
lifetime motor side:
lubrication rolling element with lifetime lubrication
Explosion protection
Version U standard, non--flameproof
Version X flameproof, ATEX II 2G T3 --
Version Y (Var.: II 2G T4) --
Version W non-flameproof --
Motor
Starting method direct or star-delta (690 V only direct) direct
Voltage 400 V (Var.: 380 V, 415 V, 500 V, 690 V) 400 V
Cooling surrounding pumped liquid surrounding pumped liquid (Var.: jacket cooling)
Immersion depth max. 100 ft
Rubber hose, type see motor catalogue (Var.: EMV-power cable)
Power cable (Var.: Tefzel = fluoropolymer
--
ETFE modified)
Length 10 m (Var.: up to 50 m)
Entry sealed over its entire length
Sealing
Elastomers nitrile rubber NBR (Var. Viton = fluororubber FPM)
mechanical seal
Shaft sealing bellows-type mechanical seal (Var.: mechanical seal with covered spring)
with covered spring
Monitoring
Version U, W one control circuit, i. e. automatic start/stop when reaching the admissible winding temperature
Version X, Y same as U, W; with additional limiting circuit for flameproof equipment --
Version U, X Winding temperature monitoring
--
incl. cooling jacket Coolant temperature monitoring
pump side and
with PT100 on pump side
Bearing temp. -- motor side with
(Var.: with PT100 on motor side)
PT100
Moisture moisture moisture electrode in motor chamber
electrode in
Mechanical seal motor float switch in leakage area
float switch in leakage area
-- leakage chamber for impeller type D
Acceleration
-- option
sensor
Paint coat non-toxic standard KSB coating, colour RAL 5002 (Var.: 250 mm)
Max. temperature of pumped media
Version U 40 oC
Version X, Y 40 oC --
Version W 60 oC --
Tests
ZN 56525
Hydraulic tests
(Var.: impeller types S, D, E, F to ISO 9906/A, impeller type K to ISO 9906/1/2/A)
General accep. test ZN 56525 (Var.: with test report EN 10 204-2.2)
Installation
stationary with Installation depth up to 4.5 m
guide wire (Var.: up to 30 m; from size 200-500 on up to 15 m)
transportable up to size 300-401, except sizes 200-500/501, 200-631, 250-630 --
stationary
Installation depth up to 4.5 m
with guide rail
(Var.: up to 100 ft (30 m))
installation
stationary, dry -- with cooling jacket
1) for impeller type D: -- pump side: rolling element bearings with re--lubrication facility
-- motor side: rolling element with lifetime lubrication

15
Amarex KRT

TECHNICAL DATA -- STANDARD PROGRAMME / (standard variants)


Material variants H, C1, C2
Motor size
2-pole 01 2 ... 03 2 5 2 ... 25 2 -- -- --
4-pole 01 4 ... 03 4 4 4 ... 29 4 35 4 ... 65 4 80 4 95 4 ... 175 4
6-pole -- 4 6 ... 19 6 32 6 ... 50 6 60 6 80 6 ... 165 6
8-pole -- -- 26 8 ... 35 8 50 8 75 8 ... 130 8
Shaft material
1.4021 C45+N 1.4021
for material variants H
Shaft prot. sleeve -- 1.4021
Shaft material
1.4462 / C45+N 1.4021
for material variants C1, C2
Shaft prot. sleeve -- 1.4462
Inlet flange (Var.: drilled to DIN 2501)
pump side: rolling element bearings
with re--lubrication facility
Bearings rolling element with lifetime lubrication
motor side: rolling element
with lifetime lubrication
Explosion protection
Version U standard, non--flameproof
Version X -- ATEX II 2G T3
(Var.:
Version Y ATEX II 2G T4 --
ATEX II 2G T4)
Version W non-flameproof
Motor
Starting method direct direct or star-delta
400 V
400 V
Voltage (Var.: 230 V, 500
(Var.: 380 V, 415 V, 500 V, 690 V)
V, 690 V)
Cooling by surrounding pumped liquid
Immersion depth max. 30 m
C2: TEFZEL
Power cable H, C1: Rubber Rubber hose, type see motor catalogue
hose, type see
motor catalogue
-- Special cable (Var.: TEFZEL = fluoropolymer ETFE modified), (Var.: EMV-cable)
Length 10 m (Var.: up to 50 m)
Entry sealed over its entire length
Sealing
Elastomers nitrile rubber NBR, (Var.: fluororubber), for C2 always fluororubber FPM
C1: bellows-type mechanical seal, (Var.: mech. seal with covered spring)
Shaft sealing
H, C2: mechanical seal with covered spring
Monitoring
one control circuit,
Version U, W
i. e. automatic start/stop when reaching the admissible winding temperature
Version X, Y same as U, W; with additional limiting circuit for flameproof equipment
Moisture moisture electrode in motor chamber
H: non-toxic KSB standard paint, colour RAL 5002 (Var.: 250 mm 2-comp. epoxy resin)
Paint coat
C1, C2: without paint coat
Max. temperature of pumped media
Version U
40 oC
Version X, Y
Version W 60 oC
Tests
ZN 56525
Hydraulic tests
(Var.: impeller types S, F to ISO 9906/A, impeller type K to ISO 9906//1/2/A)
General ZN 56525
acceptance test (Var.: with test report EN 10 204-2.2)
Installation
stationary with guide wire Installation depth up to 4.5 m
(Var.: up to 30 m)
transportable Installation depth up to 4.5 m

16
Amarex KRT

Typical sectional drawing


Pump sizes up to 4 kW Pump sizes > 4 kW to 30 kW
Installation types P and S Installation types D, H, K, P and S
Example: Amarex KRT F 80-210 / 03 4 YC2 Example: Amarex KRT F 100-250 / 7 4 XG

Pump sizes > 30 kW up to approx. 60 kW, installation types P and S


Example: Amarex KRT 150-401 / 65 4 XG Example: Amarex KRT D 300-400 / 32 6 XG

17
Amarex KRT

Typical sectional drawing


Pump sizes > 60 kW Pump sizes > 30 kW
Installation types P and S Installation types D and K
Example: Amarex KRT K 150-401 / 80 4 XNG--S Example: Amarex KRT K 150-401 / 80 4 XNG--K

18
Amarex KRT

Shaft Seal
Standard version
Mechanical seal with elastomer bellows (NBR, optional: Viton) for all kinds of waste water.

motor side

pump side

Standard variant
Inboard mechanical seal with covered spring for heavily abrasive products or products containing metal solids (e.g. swarf).

motor side

standard for H and C2


(optional for G, G1, G2, GH, C1)

pump side

19
Amarex KRT

Subject to modification without notice


02.2011
2553.5/ 9--EN

KSB Aktiengesellschaft
P.O. Box 200743 • 06008 Halle (Saale) • Turmstraße 92 • 06110 Halle (Germany)
Tel. +49 (345) 48 26 0 • Fax +49 (345) 48 26 46 99 • www.ksb.com

You might also like