Scribd
Upload
69 views2 pages

Opc-2275 Im Eng 0

Manuel décrivant le câble OPC-2275 ICOM

Uploaded by

Herve ngeleka
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
69 views2 pages

Opc-2275 Im Eng 0

Manuel décrivant le câble OPC-2275 ICOM

Uploaded by

Herve ngeleka
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INSTRUCTION MANUAL

CONNECTION CABLE Thank you for purchasing this Icom product.


The OPC-2275 CONNECTION CABLE is used to connect a
transceiver to the VE-PG3.
READ ALL INSTRUCTIONS carefully and completely be-
fore using the cable.

CONNECTING THE OPC-2275

1 Set the transceiver channel, volume level, TX output power, and other necessary settings.
(See the transceiver and the VE-PG3 instruction manuals for setting details.)

2 Turn OFF both the transceiver and the VE-PG3. Remove the microphone and external speaker from the transceiver,
and then connect the OPC-2275, as shown below.
Icom’s transceiver
VE-PG3 (Rear view) (IC-F5060/IC-F6060 series) (Rear view)

PHONE LINE2 LINE1

To [TRX1] (Upper slots)


To the external speaker jack
Be sure to insert the
A B C connectors top side up. (Front view)

1 2 3 4
A

A B C Top Bottom

To the microphone connector

OPC-2275

• The [TRX1] and [TRX2] ports (upper slots) accept the OPC-2275 connectors,
however, follow the example to correctly connect the transceiver to ONLY the [TRX1] on the VE-PG3.

CAUTION
• Verify that both the transceiver and the VE-PG3 are turned OFF when connecting or disconnecting the cable.
• Hold the connector body when connecting or disconnecting them.

When other cables are connected, you can


use needle-nose pliers to carefully insert or
remove connectors.
Connector
Needle-nose pliers body NEVER pull the connector by holding the
cable. This will damage the cable.
*If the cable becomes damaged, replace the
connector(s). See “REPLACING THE
CONNECTOR” on the reverse side for
VE-PG3 (Rear view) replacement details.

• Never bend or pinch the cable.


• Never place a heavy object on the cable.
• Never touch the cable with wet hands.
• Always connect the cable correctly. An incorrect connection could damage the VE-PG3 and/or the transceiver.
REPLACING THE CONNECTOR

If the cable becomes damaged, replace the connector(s). Make wire connections as described below.
• Spare connectors*1 are supplied with the VE-PG3.
*1 Manufacturer: DDK. Name: 232D-04S1B-DA5-FA (Equivalent to the OPC-2275 connector.)

The connector has two parts; a black base and a clear insert. DO NOT lock the connector parts before inserting all wires.
RECOMMENDATION
1 Inser t the wires into the holes 2 Press the clear insert down
according to the assigned pin until it locks in place. If reconnecting is re-
numbers. peated about 30 times,
cut the wires*2 *3 near
the connector and re- 1 2 3 4

Connector place the connector.


(Supplied with
the VE-PG3) *2 Remove the cable from the VE-PG3,
before cutting the wires.
*3 DO NOT cut the wires too short. Other-
The wires for each hole are wise it will be difficult to reconnect them
assigned by color. See the • After the insert is locked, it is to the VE-PG3.
illustration below. impossible to release it again.

OPC-2275 connection and wires assignment


• Turn OFF the VE-PG3 and the transceiver before connecting or disconnecting the OPC-2275.

VE-PG3 (Rear view) PHONE LINE2 LINE1

To [TRX1] (Upper slots)


A B C Connector top (Expanded view)

A B C

A B C

1 2 3 4 1 2 3 4 1 2 3 4
OPC-2275 White Brown Yellow Red
Gray
Blue
Green
Black

To the transceiver

• Follow the example to correctly connect the transceiver to [TRX1] on the VE-PG3.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia and/or other countries.

A-7044X-1EX
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Printed in Japan
© 2012 Icom Inc.

You might also like