DMC SZ1

ORDER NO.
DSC1202006CE
B26
Digital Camera
Model No. DMC-SZ1P
DMC-SZ1PC
DMC-SZ1PU
DMC-SZ1EB
DMC-SZ1EE
DMC-SZ1EF
DMC-SZ1EG
DMC-SZ1EP
DMC-SZ1GA
DMC-SZ1GC
DMC-SZ1GD
DMC-SZ1GF
DMC-SZ1GH
DMC-SZ1GK
DMC-SZ1GN
DMC-SZ1GT
DMC-SZ02P
Colour
[DMC-SZ1]
(S)...........Silver Type (except PC/EF/GD)
(K)...........Black Type
(A)...........Blue Type (except EE/GC/GD/GH/GT)
(R)...........Red Type (except EE/GD/GT)
(V)...........Violet Type (only EB/EF/EG/EP)
[DMC-SZ02]
(K)...........Black Type
© Panasonic Corporation 2012 Unauthorized copy-

ing and distribution is a violation of law.
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3 11 Block Diagram --------------------------------------------------- 40
1.1. General Guidelines ----------------------------------------3 11.1. Overall Block Diagram---------------------------------- 40
1.2. Leakage Current Cold Check ---------------------------3 11.2. System Control Block Diagram ---------------------- 41
1.3. Leakage Current Hot Check (See Figure. 1)--------3 11.3. Video/Audio Process Block Diagram --------------- 42
1.4. How to Discharge the E.Capacitor on Flash 11.4. Sensor Block Diagram --------------------------------- 43
Top P.C.B. ----------------------------------------------------4 11.5. Lens Drive Block Diagram----------------------------- 44
2 Warning --------------------------------------------------------------5 11.6. Power Block Diagram----------------------------------- 45
2.1. Prevention of Electrostatic Discharge (ESD) 12 Wiring Connection Diagram -------------------------------- 46
to Electrostatically Sensitive (ES) Devices ----------5 12.1. Interconnection Diagram------------------------------- 46
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. How to Replace the Lithium Battery -------------------6
3 Service Navigation------------------------------------------------7
3.1. Introduction --------------------------------------------------7
3.2. Important Notice -------------------------------------------7
3.3. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------7
3.4. Important Notice 1:(Other than U.S.A. and
Canadian Market) ------------------------------------------7
3.5. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------8
4 Specifications ---------------------------------------------------- 13
5 Location of Controls and Components------------------ 14
6 Service Mode ----------------------------------------------------- 16
6.1. Error Code Memory Function ------------------------- 16
7 Service Fixture & Tools --------------------------------------- 19
7.1. Service Fixture and Tools ------------------------------ 19
7.2. When Replacing the Main P.C.B. -------------------- 20
7.3. Service Position ------------------------------------------ 20
8 Disassembly and Assembly Instructions --------------- 21
8.1. Disassembly Flow Chart-------------------------------- 21
8.2. P.C.B. Location ------------------------------------------- 21
8.3. Disassembly Procedure -------------------------------- 21
8.4. Lens Disassembly Procedure ------------------------- 27
8.5. Removal of the Focus Motor -------------------------- 29
8.6. The Application of Grease Method ------------------ 29
8.7. Removal of the CCD Unit ------------------------------ 30
9 Measurements and Adjustments -------------------------- 31
9.1. Introduction ------------------------------------------------ 31
9.2. Before Disassembling the unit ------------------------ 31
9.3. Details of Electrical Adjustment----------------------- 33
9.4. After Adjustment------------------------------------------ 38
10 Maintenance ------------------------------------------------------ 39
10.1. Cleaning Lens and LCD Panel ----------------------- 39
2
1 Safety Precautions
1.1. General Guidelines 1.3. Leakage Current Hot Check
1. IMPORTANT SAFETY NOTICE (See Figure. 1)
There are special components used in this equipment
1. Plug the AC cord directly into the AC outlet. Do not use
which are important for safety. These parts are marked by
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
in the Schematic Diagrams, Circuit Board Layout,
capacitor, between each exposed metallic part on the set
Exploded Views and Replacement Parts List. It is essen-
and a good earth ground, as shown in Figure. 1.
tial that these critical parts should be replaced with manu-
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
facturer’s specified parts to prevent X-RADIATION,
measure the potential across the resistor.
shock, fire, or other hazards. Do not modify the original
4. Check each exposed metallic part, and measure the volt-
design without permission of manufacturer.
age at each point.
2. An Isolation Transformer should always be used during
5. Reverse the AC plug in the AC outlet and repeat each of
the servicing of AC Adaptor whose chassis is not isolated
the above measurements.
from the AC power line. Use a transformer of adequate
6. The potential at any point should not exceed 0.75 V RMS.
power rating as this protects the technician from acci-
A leakage current tester (Simpson Model 229 or equiva-
dents resulting in personal injury from electrical shocks. It
lent) may be used to make the hot checks, leakage cur-
will also protect AC Adaptor from being damaged by acci-
rent must not exceed 1/2 mA. In case a measurement is
dental shorting that may occur during servicing.
outside of the limits specified, there is a possibility of a
3. When servicing, observe the original lead dress. If a short
shock hazard, and the equipment should be repaired and
circuit is found, replace all parts which have been over-
rechecked before it is returned to the customer.
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, Figure. 1
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 MΩ and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
3
1.4. How to Discharge the E.Capacitor on Flash Top P.C.B.
CAUTION:
1. Be sure to discharge the E.capacitor on FLASH TOP P.C.B..
2. Be careful of the high voltage circuit on FLASH TOP P.C.B. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Install the insulation tube onto the lead part of resistor (ERG5SJ102:1kΩ /5W).
(An equivalent type of resistor may be used.)
3. Place a resistor between both terminals of E.capacitor on the FLASH TOP P.C.B. for approx. 5 seconds.
4. After discharging, confirm that the E.capacitor voltage is lower than 10V by using a voltmeter.
Fig. F1
4
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)
5
2.3. How to Replace the Lithium Battery
2.3.1. Replacement Procedure
1. Remove the SUB OPERATION P.C.B.. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B9501” at component side of SUB
OPERATION P.C.B.) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Type No. ML421 includes electric lead terminals.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML421 Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-SZ1/SZ02 series, as well.
6
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. Important Notice

3.2.1. CCD UNIT:
• The image sensor (CCD) unit which are connected to the lens unit with 3 screws.
These screws are locked with the screw locking glue, after performing the Optical tilt adjustment.
During servicing, if one of CCD fixing screws are loosened, the Optical tilt adjustment must be performed.
About the Optical tilt adjustment, refer to the "9.3.2 Adjustment Specifications" for details.
3.2.2. About Flexible Cable and Connector

Do not touch carelessly so that the foreign body should not adhere to the terminal part of flexible cable and connector.
Wipe off with a clean cloth and the cotton bud, etc. when the terminal part is dirty.
3.3. General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.4. Important Notice 1:(Other than U.S.A. and Canadian Market)

1. The service manual does not contain the following information because of issues servicing to component level without neces-
sary equipment/facilities.
a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B. and SUB OPERATION P.C.B..
b. Parts list for individual parts for MAIN P.C.B. and SUB OPERATION P.C.B..
When a part replacement is required for repairing MAIN P.C.B. and/or SUB OPERATION P.C.B., replace as an assembled
parts. (MAIN P.C.B./SUB OPERATION P.C.B.)
2. The following category is/are recycle module part. please send it/them to Central Repair Center.
• MAIN P.C.B. (VEP56149A)
• SUB OPERATION P.C.B. (VEP59108A): Excluding replacement of Lithium Battery.
7
3.5. How to Define the Model Suffix (NTSC or PAL model)
There are nine kinds of DMC-SZ1 and SZ02, regardless of the colours.
• a) DMC-SZ1P/PC
• b) DMC-SZ02P
• c) DMC-SZ1EB/EF/EG/EP
• d) DMC-SZ1EE
• e) DMC-SZ1GD
• f) DMC-SZ1GK
• g) DMC-SZ1GN
• h) DMC-SZ1GT
• i) DMC-SZ1PU/GA/GC/GF/GH
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash-ROM mounted on MAIN P.C.B..
3.5.1. Defining methods:

To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The service software is available at “TSN Website”. To download, click on “Support Information from NWBG/VDBG-AVC”.
8
3.5.2. INITIAL SETTINGS:
After replacing the MAIN P.C.B., make sure to perform the initial settings after achieving the adjustment by ordering the following
procedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, make sure to read the following CAUTIONS.
2. PROCEDURES:
• Precautions: Read the above "CAUTION 1" and "CAUTION 2", carefully.
• Preparation:
- Attach the Battery or AC Adaptor with a DC coupler to the unit.
(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
1. Set the REC/PLAY switch to “[ REC ] (Camera mark)”, and then turn the Power on.
2. Press the [ MODE ] button, and select the [ NORMAL PICTURE ] mode by Cursor buttons, then press the [ MENU/SET ]
button.
3. Turn the Power off.
(If the unit is other than [ NORMAL PICTURE ] mode, it does not display the initial settings menu.)
• Step 1. The temporary cancellation of “INITIAL SETTINGS”:
Set the REC/PLAY switch to “[ REC ] (Camera mark)”.
While pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.
• Step 2. The cancellation of “INITIAL SETTINGS”:
Set the REC/PLAY switch to “[ PLAY ]”.
Press “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power off.
The LCD displays the " ! " mark before the unit powers down.
• Step 3. Turn the Power on:

Set the REC/PLAY switch to “[ REC ] (Camera mark)”, and then turn the Power on.
9
• Step 4. Display the INITIAL SETTING:
While pressing [ MENU/SET ] button and “[ RIGHT ] of Cursor button” simultaneously, turn the Power off.
The “INITIAL SETTINGS” menu is displayed.
There are two kinds of “INITIAL SETTINGS” menu form as follows:
[CASE 1. After replacing MAIN P.C.B.]
When MAIN P.C.B. has just been replaced, all of the model suffixes is displayed as follows. (six pages in total)
[CASE 2. Other than “After replacing MAIN P.C.B.”]
• Step 5. Choose the model suffix in “INITIAL SETTINGS”: (Refer to “CAUTION 1”)
[Caution: After replacing MAIN P.C.B.]
The model suffix can been chosen, JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.
Therefore, select the area carefully.
Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”.
10
• Step 6. Choose the model number in "INITIAL SETTINGS": (Only for "P" model.)
This step is necessary only for "P".
Only for model suffix with "P", there is two kind of model; (DMC-SZ1 and DMC-SZ02), due to difference of sales channel. There-
fore, not only model suffix, but also model number (SZ1 or SZ02) has to be set up in the "INITIAL SETTINGS".
(The "SZ1" is displayed as default status.)
When the model number is one of the "DMC-SZ02P", change the model number with the following procedure:
Press the [ Q.MENU ]/[ (Delete/Cancel) ] button in order to change the indication from "SZ1" into "SZ02".
(Each time one presses the [ Q.MENU ]/[ (Delete/Cancel) ] button, model indication is changed from "SZ1" to "SZ02" (Toggle
switch))
• Step 7. Set the model suffix in “INITIAL SETTINGS”:

Press the “[ RIGHT ] of Cursor buttons”.
The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.
(The unit is powered off automatically.)
11
• Step 8. CONFIRMATION:
Confirm the display of “PLEASE SET THE CLOCK” in concerned language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
1) As for your reference, major default setting condition is as shown in the following table.
• Default setting (After “INITIAL SETTINGS”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-SZ1P/SZ02P NTSC English Month/Date/Year
b) DMC-SZ1PC NTSC English Month/Date/Year
c) DMC-SZ1PU NTSC Spanish Month/Date/Year
d) DMC-SZ1EG PAL English Date/Month/Year
e) DMC-SZ1EP PAL English Date/Month/Year
f) DMC-SZ1EF PAL French Date/Month/Year
g) DMC-SZ1EB PAL English Date/Month/Year
h) DMC-SZ1EE PAL Russian Date/Month/Year
i) DMC-SZ1GC PAL English Date/Month/Year
j) DMC-SZ1GD NTSC Korean Year/Month/Date
k) DMC-SZ1GF PAL English Date/Month/Year
l) DMC-SZ1GA PAL English Date/Month/Year
m) DMC-SZ1GK PAL Chinese (simplified) Year/Month/Date
n) DMC-SZ1GT NTSC Chinese (traditional) Year/Month/Date
o) DMC-SZ1GH PAL English Date/Month/Year
p) DMC-SZ1GN PAL English Date/Month/Year
12
4 Specifications
13
5 Location of Controls and Components
1 Flash 1 2 3
2 Lens
3 Self-timer indicator
AF Assist Lamp
4 LCD monitor
4 8 9
5 [MENU/SET] button
6 [DISP.] button
7 [Q.MENU] /[ ] (Delete/
Cancel) button
8 [MODE] button
10
9 REC/PLAY switch 11
10 Charging lamp
5 67
11 Cursor buttons
: /Exposure compensation
: /Macro Mode
AF Tracking
: /Self-timer
: /Flash setting
12 Strap eyelet 12
Be sure to attach the strap when using
the camera to ensure that you will not 13
drop it.
13 Lens barrel
14 [AV OUT/DIGITAL] socket 14
15 Speaker 15 16 17
Be careful not to cover the speaker with
your finger. Doing so may make sound
difficult to hear.
16 Camera ON/OFF switch
17 Zoom lever
18 Microphone
18 19 20
19 Shutter button
20 Motion picture button
21 Tripod receptacle 21 22
22 Card/Battery door
23 Release lever
23
14
Basic
Selecting the Recording Mode
Slide the REC/PLAY switch to [].
Press [MODE].
Press /// to select the Recording

Mode.
Press [MENU/SET].
List of Recording Modes

} Intelligent Auto Mode
The subjects are recorded using settings automatically selected by the camera.
Normal Picture Mode
The subjects are recorded using your own settings.
Miniature Effect Mode
This is an imaging effect which defocuses the surroundings to make it look like a
diorama. (also known as Tilt Shift Focus)
± Scene Mode
This allows you to take pictures that match the scene being recorded.
Note
When the mode has been switched from Playback Mode to Recording Mode, the previously set
Recording Mode will be set.
15
6 Service Mode
6.1. Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to FLASH-ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
• Preparation
- Attach the Battery or AC Adaptor with a DC coupler to the unit.
(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
2. Press the [ MODE ] button, and select the [ NORMAL PICTURE ] mode by Cursor buttons, then press the [ MENU/SET ]
button.
• Step 1. The temporary cancellation of "INITIAL SETTINGS":
• Step 2. Execute the error code display mode:
Press the "[ RIGHT ] of Cursor button" , [ MENU/SET ] button and [ MOTION PICTURE ] button simultaneously.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display → Error code display → Operation history display →Normal display →.....
Example of Error Code Display
16
• 3. Error Code List
The error code consists of 8 bits data and it shows the following information.
17
Important notice about "Error Code List"
1) About "*" indication:
The third digit from the left is different as follows.
- In case of 0 (example: 18001000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been
completed.
It means that this error is occurred basically at user side.
- In case of 8 (example: 18801000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?60"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
• 4. How to exit from Error Code display mode:

Simply, turn the power off. (Since Error code display mode is executed under the condition of temporary cancellation of "INI-
TIAL SETTINGS", it wake up with normal condition when turn off the power.)
NOTE:
The error code can not be initialized.
18
7 Service Fixture & Tools
7.1. Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.
19
7.2. When Replacing the Main P.C.B.
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The service software is available at “TSN Website”. To download, click on “Support Information from NWBG/VDBG-AVC”.
7.3. Service Position

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection Form
1 RFKZ0494 FP9001(MAIN) - CCD UNIT 45PIN 0.3FFC
2 RFKZ0354 FP9002(MAIN) - LENS UNIT 41PIN 0.3FFC
3 RFKZ0553 PS9001(MAIN) - PP9501(SUB OPERATION) 16PIN B to B
4 RFKZ0418 PP9001(MAIN) - PS8001(FLASH TOP) 30PIN B to B
CAUTION-1. (When servicing FLASH TOP P.C.B.)

1. Be sure to discharge the E.capacitor on FLASH TOP P.C.B..
Refer to “HOW TO DISCHARGE THE E.CAPACITOR ON FLASH TOP P.C.B.”.
The E.capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH TOP P.C.B..
3. DO NOT allow other parts to touch the high voltage circuit on FLASH TOP P.C.B..
20
8 Disassembly and Assembly Instructions
8.1. Disassembly Flow Chart 8.3. Disassembly Procedure
This is a disassembling chart.
When assembling, perform this chart conversely. No. Item Fig Removal
1 Front Case Unit (Fig. D1) Card
Rear Case Unit Battery
3 Screws (A)
1 Screw (B)
2 Screws (C)
(Fig. D2) 4 Locking tabs
Front Case Unit
4 Locking tabs
Rear Case Unit
2 Jack Door (Fig. D3) 1 Groove
1 Locking tab
Side Ornament(R)
2 Locking tabs
Side Ornament(L)
Jack Door
3 Sub Operation P.C.B. (Fig. D4) PP9501 (Connector)
PCB Spacer Sub Operation P.C.B.
2 Locking tabs
PCB Spacer
4 LCD Unit (Fig. D5) 1 Locking tab
Frame Plate FP9003 (Flex)
LCD Unit
3 Locking tabs
Frame Plate
5 Top Case Unit (Fig. D6) PS8001 (Connector)
AF Panel Light
Top Case Unit
6 Flash Top P.C.B. (Fig. D7) 2 Screws (D)
Microphone Unit FP8051 (Flex)
3 Locking tabs
Flash Top P.C.B.
2 Locking tabs
Power Knob
2 Convexes
REC Button
Microphone Unit
8.2. P.C.B. Location (Fig. D8) Discharge the E.capacitor
7 Flash Unit (Fig. D9) 3 Solders
Speaker Flash Unit
2 Solders
Speaker
8 Lens Unit (W/CCD) (Fig. D10) DPR Sheet
FP9001 (Flex)
FPC Tape
FP9002 (Flex)
Lens Unit (W/CCD)
9 Main P.C.B. (Fig. D11) 1 Screw (E)
1 Convex
Main P.C.B.
10 Battery Case (Fig. D12) 1 Locking tab
Battery Out Spring
4 Locking tabs
Battery Case
11 Battery Door Unit (Fig. D13) Battery Lock Knob
Battery Lock Spring
Battery Door Unit
21
8.3.1. Removal of the Front Case Unit and
Rear Case Unit
(Fig. D1)
(Fig. D2)
22
8.3.2. Removal of the Jack Door 8.3.3. Removal of the Sub Operation
P.C.B. and PCB Spacer
(Fig. D3) (Fig. D4)
23
8.3.4. Removal of the LCD Unit and Frame 8.3.5. Removal of the Top Case Unit
Plate
(Fig. D6)
(Fig. D5)
24
8.3.6. Removal of the Flash Top P.C.B.
and Microphone Unit
(Fig. D8)
8.3.7. Removal of the Flash Unit and

Speaker
(Fig. D9)
(Fig. D7)
25
8.3.8. Removal of the Lens Unit (W/CCD) 8.3.10. Removal of the Battery Case
(Fig. D12)
(Fig. D10)
8.3.11. Removal of the Battery Door Unit
8.3.9. Removal of the Main P.C.B.
(Fig. D13)
NOTE: (When Installing)
Make sure to confirm the following points when installing:
• The Screw is tightened enough.
• Installing conditions are fine. (No distortion, no abnormal-
space.)
(Fig. D11) • No dust and/or dirt on Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
26
8.4. Lens Disassembly Procedure
Precaution:
1. Do not remove the CCD unit when disassembling or reas-
sembling the lens in order to maintain it clean.
The screw fitting the CCD unit to the master flange unit is
fixed by the bond lock with the adjustment of the installa-
tion angle of the CCD unit against the lens (optical axis
adjustment) finished.
When remove it, refer to item "8.7.".
2. Keep dust or dirt away from the lens.
To remove dirt or dust from the lens, blow with dry air.
3. Do not touch the lens surface.
4. Use lens cleaning KIT (VFK1900BK).
5. Apply grease (RFKZ0472) as shown on "THE APPLICA-
TION OF GREASE METHOD" in the figure.
8.4.1. Removal of the Zoom Motor Unit

and Lens FPC Unit
27
8.4.2. Removal of the Master Flange Unit 8.4.3. Removal of the Outside Direct
Frame Unit / 1st-3rd Lens Frame
Unit
8.4.4. 1st-3rd Lens Frame Unit
28
8.5. Removal of the Focus Motor 8.6. The Application of Grease
Method
The grease application parts of lens unit are as follows.
Apply grease additionally in the specified position if necessary.
When the grease is applied, use a toothpick and apply thinly.
• Focus motor nut sliding part
- Grease: RFKZ0472
- Amount of application: 1.5 - 2 mg
• 4th Lens Frame sub shaft
- Grease: RFKZ0472
- Amount of application: 0.5 - 1 mg
• Lead screw
- Grease: RFKZ0472
- Amount of application: 2 - 4 mg
• 4th Lens Frame spindle guide
- Grease: RFKZ0472
- Amount of application: 1 - 2 mg
29
8.7. Removal of the CCD Unit
When remove the CCD unit once (the screw(E) is loosened
even a little), the optical tilt adjustment is required.
When loosen the screw(E), necessary the optical tilt adjustment
at the end of assembling. (Refer to item "9.3.2.")
To prevent the CCD unit from catching the dust and dirt, do not
remove the CCD unit except for replacing.
30
9 Measurements and Adjustments
9.1. Introduction
When servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced.
Before disassembling the unit, it is recommended to back up the camera data stored in flash-rom as a data file.
IMPORTANT NOTICE (After replacing the MAIN P.C.B.)
After replacing the MAIN P.C.B., it is necessary to use the “DIAS” software to allow the release of adjustment flag(s).
The Adjustment software “DIAS” is available at “TSN Website”. To download, click on “Support Information from NWBG/VDBG-
AVC”.
*DIAS (DSC Integrated Assist Software)
NOTE: (When replacing the Lens unit and CCD unit)
• When the CCD unit is unavoidably removed for Lens unit, Master Flange unit and CCD unit replaced, an optical tilt adjustment is
necessary after parts are exchanged.
• The adjustment software (DSC_Tilt) is necessary to execute an optical tilt adjustment.
• The adjustment software “DSC_Tilt” is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information
from NWBG/VDBG-AVC”.
9.2. Before Disassembling the unit

9.2.1. Initial Setting Release
The cameras specification are initially set in accordance with model suffix (such as EB, EG, GK, GC, and so on.).
Unless the initial setting is not released, an automatic alignment software in the camera is not able to be executed when the align-
ment is carried out.
Note:
The initial setting should be again done after completing the alignment. Otherwise, the camera may not work properly.
Therefore as a warning, the camera display a warning symbol “ ! ” on the LCD monitor every time the camera is turned off.
Refer to the procedure described in “3.5.2 INITIAL SETTINGS” for details.
[ How to Release the camera initial setting ]

Preparation:
• Attach the Battery or AC Adaptor with a DC coupler to the unit.
2. Press the [ MODE ] button, and select the [ NORMAL PICTURE ] mode by Cursor buttons, then press the [ MENU/SET ] but-
ton.
Step 1. The temporary cancellation of “INITIAL SETTINGS”:

Step 2. Cancellation of “INITIAL SETTINGS”:
Set the REC/PLAY switch to “[ PLAY ]”.
Press “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power off.
The LCD displays the " ! " mark before the unit powers down.
31
9.2.2. Flash-Rom Data Backup
When trouble occurs, it is recommended to backup the Flash-rom data before disassembling the unit.
There are two kinds of Flash-rom data backup methods:
[ ROM_BACKUP (Method of Non-PC backup) ]
1. Insert the SD-card into the camera.
2. Set the camera to “Temporary cancellation of the initial settings”.
3. Select the “SETUP” menu.
From the “SETUP” menu, select “ROM BACKUP”.
NOTE:
This item is not listed on the customer's “SETUP” menu.
4. When this “ROM_BACKUP” item is selected, the following submenus are displayed.
[ DSC Integrated Assist Software (Method of Using PC) ]

Same as TATSUJIN software for previous models.
9.2.3. Light Box

If using VFK1164TDVLB Light Box, remove the lens connection
ring by loosing three hexagon screws.
32
9.3. Details of Electrical Adjustment
9.3.1. How to execute the Electrical Adjustment
It is not necessary to connect the camera to a PC to perform adjustments.
“Flag reset operation” and “Initial setting operation” are required when carrying out the alignment, follow the procedure below.
9.3.1.1. Startup Electrical Adjustment mode

1. Release the initial settings.
2. Insert a recordable SD card.
(Without a SD card, the automatic adjustment can not
executed.)
3. Procedure to set the camera into adjustment mode:
a. Set the REC/PLAY switch to “[ REC ] (Camera mark)”,
and then turn the Power on.
b. Press the [ MODE ] button, and select the [ NORMAL
PICTURE ] mode by Cursor button, then press the
[ MENU/SET ] button.
c. Set the REC/PLAY switch to “[ REC ] (Camera mark)”,
and then turn the Power off.
d. Turn the Power on pressing [ MENU/SET ] and
[ MOTION PICTURE ] simultaneously.
LCD monitor displays “SERVICE MODE”.(Refer to
Fig. 3-1)
9.3.1.2. Status Adjustment Flag Setting

Reset (Not yet adjusted) the status flag condition.
1. After pressing the [ DISP. ] button, the LCD monitor dis-
plays the Flag status screen (Refer to Fig.3-2)
2. Select item by pressing the Cursor buttons. (Gray cursor
is moved accordingly.)
3. Press the [ Q.MENU ]/[ (Delete/Cancel) ] button.
NOTE:
The selected item's flag has been changed from
“F (green)” to “0 (yellow)”.
*Flag conditions:
F (green)
means that the alignment has been completed and the
status flag condition is set. In this case, the flag condition
should be reset, if you try to carry out the automatic align-
ment.
0 (yellow)
means that the alignment has been not “completed” and
the status flag condition is “reset”. In this case, automatic
alignment is available.
• In case of setting the status flag into set condition again without completion of the alignment, the status flag should be SET by
using PC, or UNDO by using ROM BACKUP function.
33
9.3.1.3. Execute Adjustment
(In case of “OIS Adjustment”)
1. Perform step “9.3.1.1.” to “9.3.1.2.”, to reset the OIS flag
status “F” (Set) to “0” (Reset)
2. Press [ DISP. ] button after Flag reset.
OIS Adjustment screen is displayed on the LCD panel.
(Refer to Fig.3-3)
3. Press the [ Shutter ] button.
The adjustment will start automatically.
4. When the adjustment is completed successfully, adjust-

ment report menu appears with Green OK on the LCD
monitor. (Refer to Fig.3-4)
9.3.1.4. Attention point during Adjustment

1. Step “9.3.1.3.” procedure shows OIS adjustment as an
example. To perform the adjustment, refer to the “9.3.2.
Adjustment Specifications” table which shows key point
for each adjustment.
2. Do not move the light box, the camera or the chart while
adjusting. If one of these is moved accidentally, start the
adjustment again.
3. Do not press any buttons/keys until the default menu
(Fig.3-5) is displayed on the LCD monitor. Otherwise,
adjustment data may not be stored properly.
4. If the adjustment is interrupted accidentally, the alignment
data may not be properly saved in the Flash-rom.
9.3.1.5. Finalizing the Adjustment

1. Several adjustment flags can be reset (“F” into “0”) at the same time. In this case, when the adjustment has been completed,
the screen will change showing the adjustment for the next item until all reset items are completed.
Also, when the [ Shutter ] button is pressed, the screen jump to the next adjustment item.
2. To cancel the adjustment mode while in the process of performing the adjustment, follow this procedures.
(1) Press “[ Q.MENU ]/[ (Delete/Cancel) ] of Cursor button”.
(2) Press “[ RIGHT ] of Cursor button”.
NOTE:
• If adjustment is cancelled with above procedure, adjustment is not completed. Make sure to adjust it later.
• Adjustment software “DIAS” is able to control the status of the adjustment flags.
34
9.3.2. Adjustment Specifications
The following matrix table shows the relation between the replaced part and the Necessary Adjustment.
When a part is replaced, make sure to perform the necessary adjustment(s) in the order indicated.
The table below shows all the information necessary to perform each adjustment.
35
36
37
9.4. After Adjustment
9.4.1. Initial Setting
Since the initial setting has been released to execute the built-in adjustment software, it should be set up again before shipping the
camera to the customer.
Refer to the procedure described in “3.5.2. INITIAL SETTINGS” for details.
[ IMPORTANT ]
1. The initial setting should be done again after completing the alignment. Otherwise, the camera will not work properly.
Therefore as a warning, the camera display a warning symbol “ ! ” on the LCD monitor every time the camera is turned off.
2. Confirm that status of all adjustment flag show “F”. Even if one of the adjustment flag shows “0”, initial setting programmed is
never executed.
38
10 Maintenance
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.
39
11 Block Diagram
11.1. Overall Block Diagram
OVERALL BLOCK DIAGRAM
(25mm ~ 250mm)
IC3001
CCD SIGNAL
CCD PROCESSOR X6001
1/2.33" 16.1 MEGA PIX (24MHz)
CDS, AGC,
A/D, TG,
CCD DRIVER
SD
ZOOM OIS UNIT IRIS SHUTTER FOCUS CARD
IC3003
REGULATOR
COLOR LCD
IC9101 PANEL
SYSTEM IC 3.0" PANEL
MOTOR DRIVE, 230k dots
OIS DRIVE&
PRE PROCESS
IC7101
GYRO MICROPHONE
SENSOR & AMP
IC6001
VENUS ENGINE IC9101
SYSTEM IC SPEAKER
CAMERA PROCESS
J-PEG COMP/EX PANDS MICROPHONE AMP
IC8001
FLASH IGBT DRIVER MEDIA I/F SPEAKER CONTROL
USB I/F VIDEO OUT
MAIN MICROPROCESSOR
OIS CONTROL
LENS DRIVE
LCD DRIVE AV OUT / DIGITAL
REAR OPERATION UNIT TERMINAL
IC1502
IC9101 CONNECTOR I/F
SYSTEM IC
X9101
(32.72kHz)
IC6002 IC1501 BATTERY

SDRAM/1Gbit SWITCHING
NAND FLASH ROM/1Gbit CHARGER
TOP OPERATION UNIT
IC1001 IC1110,1120,
POWER IC1220
(POWER SUPPLY)
REGULATOR
DMC-SZ1/SZ02 OVERALL BLOCK DIAGRAM
40
11.2. System Control Block Diagram
SYSTEM CONTROL BLOCK DIAGRAM
FLASH TOP P.C.B.
IC6001 SAFETY GND
(VENUS ENGINE)
IC6002 TL8007
(SDRAM/1Gbit, NAND FLASH ROM/1Gbit)
(SHUT FULL)
GPIO51 AA1 PP9001 PS8001
TL8004
SDRAM AREA/1Gbit 8-10,13-15 8-10,13-15
BA0D 73 M24 DRBA0 (TELE WIDE)
Bank Adr. Bank Adr. PP9001 PS8001 T
BA1D 82 M21 DRBA1 ADC4 AC17 3 4
22 22 S8003
S8002 W
DQ31D 17 B22 DRD31 2 1
T/W SW
DATA DATA CL6007 CL9004 POWER SW
DQ5D 98 T21 DRD0 (POWER ON H) (POWER ON L) PP9001 PS8001 3 ON
GPIO16 AB1 85 POWERONH POWERSWONL 87 16 16
A4D 12 G23 DRA0 (SHUT HALF) (SHUTTER 0) PP9001 PS8001
GPIO11 T2 2 SHUTTERHALF SHUTTER0 83
ADDRESS ADDRESS 23 23
PP9001 PS8001
A3D 93 L23 DRA12 17
RL6001 CL9003 17 1 OFF
DQM3D 37 C19 DRDQM3
HALF
DQM0D 78 U21 DRDQM0 5
RL6019 S8001
2 1
CKED 33 N24 DRCKE SHUTTER SW
FULL
RASD 52 H21 DRRASB 4 3
6
CKN 68 K24 DRAMFCKX PP9001 PS8001
20 20
CLKD 58 2 1
J24 DRAMFCK
S8004
MOVIE
CASD 62 G22 DRCASB
RL6009 4 3
CSD 72 M22 XDCS PIOUT1 31 D8001
RL6010
(AF LED K) PP9001 PS8001
WED 81 H24 DRWEB LEDOUT2 36
30 30
AF ASSIST LED
NAND FLASH ROM AREA/1Gbit PP9001 PS8001
PW AF3.4V 29 29
I/O3N 105 B15 CPUD16
DATA DATA
IC9101
(SYSTEM IC)
I/O4N 127 B13 CPUD23
RL6005
(MOVIE)
REN 3 D13 CPUREB ADC9 Y14
CLEN 4 C11 FR CLE

RL6014
CEN 6 D11 FROM CS SUB OPERATION P.C.B.
RL6003
WEN 7 A15 CPUWE2B
(REC PLAY) PS9001 PP9501 1 PLAY : L
GPIO75 A3
14 14
WPN 13 A12 FR WP S9511
(AGND) PS9001 PP9501 REC/PLAY SW
ALEN 14 B12 FR ALE 1 1
3
REC : H
R/BN 16 A11 FR RB
(REAR KEYIN) PS9001 PP9501
ADC5 AB15
11 11
X6001 S9508 S9503 S9502 S9501
(24MHz) MODE
DELETE DISPLAY MENU
Y24 MCK24O
2 1 2 1 2 1 2 1
AA24 MCK24I
CCD UNIT
TH3101 (CCD THERMO) 4 3 4 3 4 3 4 3
FP9001
AD17 ADC2
2
(CROSS KEYIN) PS9001 PP9501

IC9101 ADC3 AA16
15 15
(SYSTEM IC)
RL7001 S9506 S9507 S9505 S9504
(CLK27 SYS) LEFT RIGHT DOWN UP
X9101 SYSCK 58 AD4 GPIO40
(32.72KHz)
2 1 2 1 2 1 2 1
72 OSCIN (SYS RESET)
RESETOUT 88 AD7 RSTB
RL9101
73 OSCOUT
(S SYSCON CS) 4 3 4 3 4 3 4 3
SCCS 17 AC3 GPIO63
RL9103
(S SYSCON SI) D9501
SO 27 C2 GPIO69
SUB OPERATION
RL9102 PS9001 PP9501
P.C.B. (S SYSCON SO)
PS9001-5
5 5
(CTD CHGLED) CHARGE LED
SCSI 18 F5 GPIO70 PS9001 PP9501
PP9501 PS9001 USB VBUS
74 BATT 12 12
7 7 RL9104 (CHGLED A)
(S SYSCON SCK)
(DGND) PS9001 PP9501
SCSCLK 32 E3 GPIO68 9 9
B9501
TIMER
BACKUP
BATTERY
DMC-SZ1/SZ02 SYSTEM CONTROL BLOCK DIAGRAM
41
11.3. Video/Audio Process Block Diagram
VIDEO/AUDIO PROCESS BLOCK DIAGRAM
IC6002
(SDRAM/1Gbit, NAND FLASH ROM/1Gbit)
SDRAM AREA/1Gbit NAND FLASH ROM AREA/1Gbit
A0D A12D DQ0D DQ31D IO0N IO7N
DCLK FP9003
13bit ADDRESS 32bit DATA 8bit DATA 34
IC6001
(VENUS ENGINE) FP9003
33
DRA0 DRA12 DRD0 DRD31 CPUD16 CPUD23 D7
D0
FP9003
(CKG18 LCD)
LCDCLK D1 26
LCDOUT7 G5 (BUS18 LCDOUT7-0) CS

LCD
FP9003
39
LCDOUT0 F2 HSYNC
(LCD CS) FP9003
GPIO76 B4 36
(BUS18 LCDHD)
LCDHD C1
(BUS18 LCDVD) VSYNC FP9003
SENSOR SECTION LCDVD D2
35
SDA FP9003
CCD0 K1 PRE 38
CDS, CDS Signal MEMORY CONTROL BLOCK
CCD AGC PROCESS
(12Bit) BLOCK
A/D CCD11 M2 SCL FP9003
37
FCK
J1
YC JPEG VIDEO
CCDVD CCD
J2 SSG PROCESS PROCESS OUTPUT
CCDHD BLOCK BLOCK BLOCK
K5
GPIO13 (CABLE DET)

AA2
VIDEO OUT (G VIDEO OUT)
AD18
P6401
RL6401 (SD CARD CONNECTOR)
(BUS25 SDDAT0)
GPIO25 G1 7 D0
INTERNAL BUS CONTROL (BUS25 SDDAT1) JK2001
GPIO26 G2 8 D1 CL2005 (AV OUT / DIGITAL TERMINAL)
(BUS25 SDDAT2)
GPIO27 G3 9 D2
CABLE DET 1
(BUS25 SDDAT3)
GPIO28 F1 1 D3 VDD 4A PW SD3V
CL2001 VIDEO OUT 2
(BUS25 SDCMD)
SD CORE GPIO24 H3 2 CMD VDD 4B
(CLK25 SDCLK) LINE OUT 3
QR6001
GPIO23 H1 5 CLK
USB+ 5
X6001 (SDCD) C.DET IC1502
(24MHz) 10 11
(CONNECTOR I/F) CL2002 USB- 7
(SDWP) WP 6
AA24 MCK24I GPIO22 AC22 12
(SDCD SYS) 3A 6 D- 1D- 3 2 3 USB VBUS 8
GPIO45 Y6 3B CL2003
Y24 MCK24O 7 D+ 1D+ 2 1 4 CL2004
13 14
F2002
(USB CAB IN)

GPIO12 R4
USB I/F (SW USB-)
USB SIGDM AD9
(SW USB+)
USB SIG DP AD10
(S SYSCON SCK) RL9104
GPIO68 E3
(S SYSCON SO) RL9102
GPIO70 F5
CL9107 IC9101
(SYSTEM IC)
VIN 119
82 SDDETIN
VOUT 116
RL9109 4 SDDETOUT
120 CL5006 FLASH TOP P.C.B.
LINEOUT 92
(A DIN)
GPIO48 AA5 4 ADOUT
41 CL5001
4
MUTE 90 MIC
(A DOUT) CL8051
GPIO47 AA6 6 DAIN
48 PP9001 PS8001 FP8051
MICIN 99
(A FCLK) 27 27 1
CL8050
GPIO49 AA3 6 LRCLK
47 PP9001 PS8001 FP8051
4
SCSI 18
(A MCLK) 25,28 25,28 3,4
GPIO41 AD5 4 MCLK0
40 SCSCLK 32
(A DCLK)
GPIO46 AC4 6 BCLK SPEAKER
PP9001 PS8001 RL8042

RSTB (SYS RESET) SPPOS 75
AD7 88 RESETOUT 12 12
CL5002 RL8041
PP9001 PS8001
SPNEG 80
11 11
CL5003
DMC-SZ1/SZ02 VIDEO/AUDIO PROCESS BLOCK DIAGRAM
42
11.4. Sensor Block Diagram
SENSOR BLOCK DIAGRAM
(VH) FP9001 IC3001

33 PW CCD PLUS (CCD SIGNAL PROCESSOR)
(CCD IMAGE SENSOR)
Q3101
D0 17
VDD (CCD OUT) FP9001 G CCDOUT CCDIN 12-bit 12
18 6 1 79 CDS PGA To IC6001-K1 M2
35 ADC 12bit
(BUS44 CCD0-11)
D11 6
VO
19 5 2
DAC CLAMP
4 3
V1A FP9001 V1A V1

16 48 CL8004
16
V1B FP9001 V1B V2 GPO4
17 47 87 To IC8001-4
17
V2A FP9001 V2A V3 (FLASH TRG)
14 46
14
V2B FP9001 V2B V4
15 45 CL3001 VD
15
V3A FP9001 V3A V5 VD
3480pix
12 44 TIMING 5
3464pix 12 To IC6001-J2
V3B FP9001 V3B V6 GENERATOR CL3002 HD (CCDVD)
4640pix 13 43
13 HD
V4A FP9001 V4A V7
10 42 4 To IC6001-K5
4656pix 10 (CCDHD)
V4B FP9001 V4B V8
11 41
11
V5 FP9001 V5 V9
9 40 V-DRIVER
9
V6 FP9001 V6 V10 DVDD4 54
8 39
8 CL3000
V7A FP9001 V7A V11 IC3003
5 38
5 CL3003 (REGULATOR)
V8A FP9001 V7B V12
3 37
6
V8B FP9001 V8A V13 AVDD 57 1 VOUT VIN 4 PW SE2.1V
4 36
3 DVDD 58
V12 FP9001 V8B V14 2 GND VCNT 3
34 35 DRVDD 60
4
V11D FP9001 V11D V15 CLIVDD 63
35 26 34
IOVDD 67
V8X FP9001 V8X V16
2 33 TCVDD 69
18
V8Y V17 PVDD 71
FP9001 V8Y
1 32
19
V8Z FP9001 V8Z V18
42 31
20
V9X FP9001 V9X V19
41 30
21
V9Y FP9001 V9Y V20
40 29
22
V9Z FP9001 V9Z V21
39 28
23
V10 FP9001 V10 V22
37 27
24
V11 FP9001 V11 V23
36 26
25
V12 FP9001 V12 V24
34 25
27
SUB FP9001 SUB SUBCK
28 24
30
H1 FP9001 G H1 H1
27 73
41
G H2 INTERNAL CLOCKS
H2 FP9001 H2
29 74
42
H3 FP9001 G H3 H3
26 75
40
G H4 CLI
H4 FP9001 H4 H-DRIVER DLL 82 To IC6001-J1
30 76
43 (CKG44 FCK)
HL FP9001 G HL HL
25 77
39
RG FP9001 GR RG
22 78
38 RL3003
CS
32 33 23 24 1 To IC6001-J4 (S AFE CS)
SUBSW2 SUBSW1 RL3004
MSUBSW MSUB
RL3007 GPO1 SERIAL SDATA
FP9001 SUBSW1 2 To IC6001-J3 (S AFE SDATA)
84 INTERFACE RL3005
31 RL3008
FP9001 SUBSW2 GPO2
85 SCK
32 3 To IC6001-H2 (S AFE SCK)
FP9001 MSUB
50 VMM
28 RL3009
FP9001 MSUBSW GPO3
86
29
PW A3.1V
DMC-SZ1/SZ02 SENSOR BLOCK DIAGRAM
43
11.5. Lens Drive Block Diagram
LENS DRIVE BLOCK DIAGRAM
IC6001
(VENUS ENGINE)
X6001
FP9002 (24MHz)
CD BARREL & FOCUS ENC
FZHP LED MCK24I AA24
41 V1 GPIO65
FZHP ABS (G FZHP)
40 W2 GPIO55
MCK24O Y24
SUB OPERATION P.C.B.

FP9002 IC7101
ZENC1 LED PW A3.1V
38 (GYRO SENSOR & AMP)
ZENC2 LED
35
ZENC1 ABS (G ZENC1)
37 V2 GPIO54 VCC 1
ZENC2 ABS (G ZENC2)
CCD 34 Y2 GPIO53 VDD 7
FILTER (OIS GY CS)
PS9001 PP9501
IC9101 GPIO59 V3 8 CSB OUTMODE 13
6 6
(SYSTEM IC) (OIS GY SCK)
PS9001 PP9501
GPIO61 Y1 9 SCLK GND1 2
4 4
(OIS GY DI)
FP9002 34 PIOUT2 PS9001 PP9501
GPIO52 U4 10 MISO GND2 4
2 2
23 (OIS GY DO)
PS9001 PP9501
FMBP GPIO60 U3 11 MOSI GND3 6
24 8 BMP RL7002 3 3
FMBN
M 27 12 BMN EA 10
RL7003
(PWM FA)
AB8 GPIO35
28
FOCUS MOTOR FMAN (PWM FB)
22 16 AMN
EB 24 AA7 GPIO34
FMAP RL7006
25 13 AMP
26 (PWM IRIS A)
EC1 57 AA10 GPIO33
FP9002
SH+
M 7
8
22 DMP
SHUTTER MOTOR SH- RL7004 (SHUTTER A)

5 20 DMN ED1 11 AC6 GPIO39
6 RL7005 (SHUTTER B)
ED2 30 AB7 GPIO38
FP9002
IRIS+ RL7001
3 52 CMP1
(CLK27 SYS)
M 4
1
IRIS-
49 CMN1
SYSCK 58 AD4 GPIO40
RL9106
IRIS MOTOR (S DAC CK)
2 LZCK 4 AD8 GPIO31
RL9107 (S DAC DI)
LZDI 3 AB9 GPIO30
RL9105 (S DAC LD)
LZLD 7 AA11 GPIO29
IC3001
ZOOM ENC (CCD SIGNAL
CL7001 RL3003 PROCESSOR)
FP9002 (PWM YOIS) (S AFE CS)
ZM+ YPWM 54 AA9 GPIO37 1 SL
M 29
30
28 MP AFE CS J4
RL3004
(S AFE SDATA)
ZOOM MOTOR ZM- AFE SDO J3 2 SDATA
31 25 MN (PWM XOIS) RL3005 FLASH TOP P.C.B.
32 XPWM 5 AC7 GPIO36 P8002
(S AFE SCK) UNREG+
1 TL8003
AFE SCK H2 3 SCK
LENS UNIT LAMP(+)
F8021 CL8001
GPO4 T8001
87 F8001
OIS UNIT FP9002 PS8001
UNREG+ 1-4 2 3
XDR-
16 46 XMN
XDR+ CL8002 1 4
15 43 XMP C8003 CL8031
XHO+ (For Flash
20 Charge) TRG FIRST
XHO-
18
XV+ 1
HALL 17
SENSOR 19
XV- IC8001 TRG SECOND
(IGBT DRIVER) FLASH
YDR- TL8001 3
10 42 YMN
YDR+
9 38 YMP (STB CHG DET) 10 SW GND 1 CL8033
2
HALL 11 YV+ ADC7 AC16 CL8005
SENSOR 13 YV- 105 XINP 9 TEST DRVOUT 2
RL9108 TRG G
YHO+
14 (STB CHG START)
YHO- 106 XHN T3 GPIO14 CL8032
PWMIN 86 8 CS VDD 3
12
TL8002
102 YINP
7 FB DRVIN 4 LAMP(-)
CL8006
103 YHN
(STB CHG DET) PP9001 PS8001
6 STAT CHARGE 5
113 XVP 7 7
Q8001
CL8003 5 6 7 8
(STB CHG OUT) PP9001 PS8001
PWMOUT 89 19 19
112 YVP CL8004 4
(FLASH TRG) PP9001 PS8001
6 6
CL8008 3 2 1
PP9001 PS8001 (IGBT VCC)

PW AF3.4V
29 29
DMC-SZ1/SZ02 LENS DRIVE BLOCK DIAGRAM
44
11.6. Power Block Diagram
POWER BLOCK DIAGRAM
CL1001
UNREG
CL1010
JK2001 CL2004 PW SE2.1V
(AV OUT/DIGITAL TERMINAL)
F2002 IC1110 (REGULATOR)
USB VBUS 8 CL1110
CL2002 VIN VOUT
USB+ 5 3 2 4 1 PW D1.8V
CL2003
USB- 7 4 1
8 7 6 5 4 3 2 1 CURRENT LIMIT
PGND
LX
LX
VREG
VIN
VIN
VBUS
VBUS
ERROR AMP
DIS-
9 PGND NON RUSH CHARGE
Q1501 TSD
FLASH TOP P.C.B. IC1501
10 SYSTEM (SWITCHING CHARGER) CE VOLTAGE
P8002 PW A3.1V 4 3 3 ON/OFF REFERENCE
CL1501 CONTROL
(BATTERY TERMINAL) 11 SYSTEM
F8021 CE
PS8001 PP9001 EACH 2
UNREG+ 1 12 VBAT USB OK 29 5 2 PW 5V VSS
1-4 1-4 CIRCUIT CL1020
BAT THERMO PS8001 PP9001 FB 28
2 13 VBAT
18 18 CL1002 PW AF3.4V
6 1
PS8001 PP9001
UNREG GND 4 CL9005 14 TH SCL 27
8-10,13-15 8-10,13-15 IC1120
(REGULATOR)
15 CEN SDA 26
CL8026
XPWER ON
IUSSET2
VIN
IUSSET1
16 USUS VDD 25 4
POWER SW CL9004
GND
CRG
CL1120
CTI
DM
VREF
DP
S8002 ON PS8001 PP9001 VOUT
16 16 17 18 19 20 21 22 23 24 1 PW A3.1V
OCP
To PS9001-5
OFF (CTD CHGLED) TSD
CE
3 STBY
DISCHARGE
IC1502
(CONNECTOR I/F)
IC1220
(REGULATOR)
1 VCC GND 8 9 8 7 6 5 4 3 2 1 CL1221
2 ID+ D+ 7
IC6001
RT
VDD
VREGA
VCC
SDL
SDA
GND
STB123
DCG
VOUT1
5 PW SD3V
(VENUS ENGINE) 3 ID- D- 6
CFB
4 GND OE 5 10 INV6 IN-RUSH- CURRENT
(CRG EN) QR1501 CURRENT- LIMIT
GPIO9 P4 PREVENT ERROR
11 INV5 LX1 35
(USIS) EN1 AMP
GPIO15 U2 CL1502 3 ON/OFF
(XPW ON) 12 VREF5 HX13 34 CONTROL
GPIO73 C5 VOLTAGE
(SW USB-) 13 VO3 PGND13 33 REFERENCE
USBSIGDM AD9 VIN
IC1001 2 4
(SW USB+) 14 VO7 LX21 32 VSS
USBSIGDP AD10 (7CH SW REGULATOR) CL1220
15 VO1 TSD
(BATT THERMO V) LX22 31 VOUT2
ADC1 AC18 6 PW D3V
16 LED HX2 30
IC9101 CFB
(SYSTEM IC) IN-RUSH- CURRENT
17 INV7 VO2E 29 CURRENT- LIMIT
PREVENT ERROR
87 POWERSWONL EV3 68 18 LX7 PGND2 28 EN2 AMP
1 ON/OFF
PGND567
CL6008 UNREG 63 CONTROL
PGND4
VOLTAGE
HX567
(POWER SW ON)
HX4E
HS6L
POWERCTLSW 62 REFERENCE
LX6
LX5
LX4
LX3
GPIO18 AA23 1 POWERSWONH
RESETOUT 88 19 20 21 22 23 24 25 26 27
POWERONH CL1003
CL1030
85
CL6007 PW D1.2V
(POWER ON H) CL1040
GPIO16 AB1
PW 5V
CL1050
To IC3001-53
(PW CCD MINUS)
CL1060
(SYS RESET)
RSTB AD7
To IC3001-51
CL1005 (PW CCD PLUS)
(S11C SDA) CL1061
GPIO58 V23
CL1006
(S11C SCL)
GPIO57 AB24 NC
CL1070 (PW CCD PLUS 17)
(SD3V CTL)
GPIO67 R3
To FP9003-2
MCK24I MCK24O (PW BL VDD)
AA24 Y24
CL1004
To FP9003-1
X6001
(24MHz) (PW BL MINUS)
DMC-SZ1/SZ02 POWER BLOCK DIAGRAM
45
12 Wiring Connection Diagram
12.1. Interconnection Diagram
INTERCONNECTION DIAGRAM
SPEAKER
PS8001
7 STB CHG DET

17 SHUTTER 1 14 UNREG GND
18 BATT THERMO 13 UNREG GND
10 UNREG GND
9 UNREG GND
8 UNREG GND
16 POWER ON L 15 FRAME GND
FLASH TRG
UNREG+
UNREG+
UNREG+
UNREG+
SP NEG
SP POS
NC
RL8042 RL8041
FP8051
P8002
19 STB CHG OUT 12

11
6
5
4
3
2
1
FLASH TOP P.C.B.
MIC GND R
MIC GND L
2 BAT THERMO
4 UNREG GND
23 SHUTTER 0
MIC R
22 TELE WIDE
MIC L
CATHODE
IGBT VCC
STB GND
MIC GND
MID GND
MIC RIN
(COMPONENT SIDE)
UNREG+
MIC LIN
MOVIE
NC
NC
1
4
3
2
20
21
24
25
26
27
28
29
30
3
MICROPHONE
BATTERY
FP9001
1 CON CHK
2 CCD THERMO
18 BATT THERMO
19 STB CHG OUT
16 POWER ON L
3 V8A
SHUTTER 1
SHUTTER 0
TELE WIDE
V8B
CATHODE
4
IGBT VCC
MIC GND
MIC GND
V7A
MIC RIN
5
MIC LIN
MOVIE
A GND
6 V7B
VL
NC
7
8 V6
9 V5
10 V4A
11 V4B
12 V3A
13 V3B
14 V2A
15 V2B
17
20
21
22
23
24
25
26
27
28
29
30
16 V1A
17 V1B
18 V8X
19 V8Y
7 STB CHG DET

14 UNREG GND
13 UNREG GND
10 UNREG GND
9 UNREG GND
8 UNREG GND
15 FRAME GND
20 V8Z
FLASH TRG
CCD 21 V9X
UNREG+
UNREG+
UNREG+
UNREG+
SP NEG
SP POS
22 V9Y
UNIT 23 V9Z
NC
24 V10
25 V11
26 V11D
27 V12
28 MSUB
29 MSUBSW
30 SUB
31 SUBSW1
32 SUBSW2
12
11
6
5
4
3
2
1
33 VH
LENS 34 CCD GND
35 CCD OUT
36 CCD GND PP9001
UNIT 37 CCD GND
38 RG
39 HL
40 H3
41 H1
42 H2
43 H4
44 CCD GND
45 CON CHK
FP9003
41 VCOM LCD UNIT
40 GRB/NC
39 CS
38 SDA
37 SCL
36 HSYNC
35 VSYNC
34 DCLK
MAIN P.C.B. 32 D6
33
31
D7
D5
30 D4
(FOIL SIDE) 28 D2
29
27
D3
D1
26 D0
25 GND
24 LCD DET1
23 LCD DET2
22 VDD
21 DVDD
20 V1
19 V2
18 V3
17 V4
16 VDD2
15 V5
14 V6
13 NC/VDD3
12 NC/VDD5
10 V8
11
9
V7
VGH
SUB OPERATION
8 VGL
6 FRP
7
5
AGND
COMDC
P.C.B.
4 VCAC
FP9002
2 VLED+
3
1
VCOM
VLED-
(FOIL SIDE)
1 IRIS-
2 IRIS-
3 IRIS+
4 IRIS+
5 SH-
6 SH-
7 SH+
8 SH+
9 YDR+
10 YDR-
11 YV+
12 YHO-
13 YV-
14 YHO+
15 XDR+
16 XDR-
17 XV+
18 XHO-
19 XV-
20 XHO+ PS9001
21 GND PP9501
22 FMAN
23 FMBP 16 A3R1V 1 AGND 1 AGND 16 A3R1V
24 FMBP
25 FMAP 15 CROSS KEYIN 2 OIS GY DI 2 OIS GY DI 15 CROSS KEYIN
26 FMAP
27 FMBN 14 REC PLAY 3 OIS GY DO 3 OIS GY DO 14 REC PLAY
28 FMBN
29 ZM+ 13 NC 4 OIS GY SCK 4 OIS GY SCK 13 NC
30 ZM+
31 ZM- 12 USB VBUS 5 CTD CHGLED 5 CTD CHGLED 12 CHGLED A
32 ZM-
33 GND 11 REAR KEYIN 6 OIS GY CS 6 OIS GY CS 11 REAR KEYIN
34 ZENC2 ABS
35 ZENC2 LED 10 NC 7 CLOCK 7 CLOCK 10 NC
36 ZENC VCC(D2R9V)
37 ZENC1 ABS 9 DGND 8 NC 8 NC 9 DGND
38 ZENC1 LED
39 FZHP VCC(D2R9V)
40 FZHP ABS
41 FZHP LED
DMC-SZ1/SZ02 INTERCONNECTION DIAGRAM
46
Model No. : DMC-SZ1/SZ02 Schematic Diagram Note
Model No. : DMC-SZ1/SZ02 Parts List Note
Model No. : DMC-SZ1/SZ02 Power (P) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 USB (U) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 Jack (J) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 SENSOR (SE) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 LCD (L) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 Digital (D) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 SD Card (SD) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 System Driver (SY) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 Main Connection (MC) (Main P.C.B.)
Model No. : DMC-SZ1/SZ02 Sub Operation (R) (Sub Operation P.C.B.)
Model No. : DMC-SZ1/SZ02 Gyro (GY) (Sub Operation P.C.B.)
Model No. : DMC-SZ1/SZ02 Flash Top (Flash Top P.C.B.)
Model No. : DMC-SZ1/SZ02 CCD (CCD Flex P.C.B.)
Model No. : DMC-SZ1/SZ02 Lens Flex (Lens Flex P.C.B.)
Model No. : DMC-SZ1/SZ02 Main P.C.B. (Component Side)
Model No. : DMC-SZ1/SZ02 Main P.C.B. (Foil Side)
Model No. : DMC-SZ1/SZ02 Sub Operation P.C.B. (Component Side)
Model No. : DMC-SZ1/SZ02 Sub Operation P.C.B. (Foil Side)
Model No. : DMC-SZ1/SZ02 Flash Top P.C.B. (Component Side)
Model No. : DMC-SZ1/SZ02 Flash Top P.C.B. (Foil Side)
Model No. : DMC-SZ1/SZ02 CCD Flex P.C.B. (Component Side)
Model No. : DMC-SZ1/SZ02 CCD Flex P.C.B. (Foil Side)
Model No. : DMC-SZ1/SZ02 Lens Flex P.C.B.
Model No. : DMC-SZ1/SZ02 Parts List
Ref.
Safety Part No. Part Name & Description Q'ty Remarks
No.
C1001 F1J1A106A024 C.CAPACITOR CH 10V 10U 1
C1004 F1H1A105A025 C.CAPACITOR CH 10V 1U 1
C1050 F1J1C106A059 C.CAPACITOR CH 16V 10U 1
C1051 F1G1H122A416 C.CAPACITOR CH 50V 1200P 1
C1052 F1G1A1040006 C.CAPACITOR CH 10V 0.1U 1
C1060 F1J1C475A059 C.CAPACITOR CH 16V 4.7U 1
C1070 F1J1E4750002 C.CAPACITOR CH 25V 4.7U 1
C1110 F1H1A225A051 C.CAPACITOR CH 10V 2.2U 1
C1120 F1G0J1050007 C.CAPACITOR CH 6.3V 1U 1
C1502 F1H1A4750001 C.CAPACITOR CH 10V 4.7U 1
C1505 F1G1H1020008 C.CAPACITOR CH 50V 1000P 1
C3001 F3Z0E1070001 CHIP CAPACITOR 1
C3002 F1H1E105A116 C.CAPACITOR CH 25V 1U 1
C3006 F1H0J1050013 C.CAPACITOR CH 6.3V 1U 1
C3015 F1G1C1030008 C.CAPACITOR CH 16V 0.01U 1
C3020 F1H1H104A913 C.CAPACITOR CH 50V 0.1U 1
C3022 F1H1C105A097 C.CAPACITOR CH 16V 1U 1
C3023 F1H1H104A913 C.CAPACITOR CH 50V 0.1U 1
C3030 F1G1C104A077 C.CAPACITOR CH 16V 0.1U 1
C4009 F1H1E105A144 C.CAPACITOR CH 25V 1U 1
C5009 F1H0J4750005 C.CAPACITOR CH 6.3V 4.7U 1
Ref.
No.
C6014 F1H0J106A009 C.CAPACITOR CH 6.3V 10U 1
C6401 F1J0J2260004 C.CAPACITOR CH 6.3V 22U 1
C7101 F1J0J1060009 C.CAPACITOR CH 6.3V 10U 1
C8006 F1K2E4730005 C.CAPACITOR 250V 0.047U 1
C9101 F1G1E102A086 C.CAPACITOR CH 25V 1000P 1
Ref.
No.
CX6001 F5A84103A020 CAPACITOR NETWORKS 1
D1050 B0JCFC000003 DIODE 1 E.S.D.
D3001 DA2S10100L DIODE 1 E.S.D.
D4001 DB2S31100L DIODE 1 E.S.D.
D6001 DA2S10100L DIODE 1 E.S.D.
D8001 B3ADB0000142 DIODE 1 E.S.D.
D8002 B0ECFR000003 DIODE 1 E.S.D.
D9101 DB3S406F0L DIODE 1 E.S.D.
D9102 B0ADEJ000054 DIODE 1 E.S.D.
D9501 B3AAB0000343 LED 1 E.S.D.
ET9001 K4ZZ01000208 EARTH TERMINAL 1
ET9002 K4ZZ01000208 EARTH TERMINAL 1
F2001 K5H1522A0018 FUSE 32V 1.5A 1
F2002 K5H202Y00007 FUSES 1
F8001 ERBRE1R25V FUSE 32V 1.25A 1
F8021 ERBRE2R00V FUSE 1
FP8051 K1MY04BA0370 CONNECTOR 4P 1
IC1001 C1ZBZ0004597 IC 1 E.S.D.
IC1110 C0DBGYY00779 IC 1 E.S.D.
IC1501 C1ZBZ0004582 IC 1 E.S.D.
IC1502 C1CB00003709 IC 1 E.S.D.
IC3001 C1AB00003797 IC 1 E.S.D.
IC6001 MN89513 IC 1 E.S.D.
IC6002 RS10310 IC 1 E.S.D.
IC7101 EWTS9PSL1A IC 1 [SPC], E.S.D.
IC8001 C0ZBZ0001710 IC 1 E.S.D.
IC9101 C1AB00003785 IC 1 E.S.D.
JK2001 K1FB108E0008 JACK, AV/USB 1
L1010 G1C100KA0148 CHIP INDUCTOR 10UH 1
L1020 G1C3R3MA0392 CHIP INDUCTOR 3.3UH 1
L2001 J0ZZB0000142 FILTER 1
L3003 G1C100MA0410 CHIP INDUCTOR 10UH 1
L3004 G1C100KA0115 CHIP INDUCTOR 10UH 1
L8001 G5F1A0000026 CHIP INDUCTOR 1
LB2001 J0JCC0000415 FILTER 1
P6401 K1NA09E00098 SD CARD CONNECTOR 1
P8002 K4ZZ03000344 OTHER TERMINALS 1
PP9001 K1KA30BA0342 CONNECTOR 30P 1
PP9501 K1KY16AA0749 CONNECTOR 16P 1
Ref.
No.
PS8001 K1KB30AA0123 CONNECTOR 30P 1
PS9001 K1KY16AA0748 CONNECTOR 16P 1
Q1501 FG6943010R TRANSISTOR 1 E.S.D.
Q3101 DMS935E10R TRANSISTOR 1 E.S.D.
Q8001 B1JBLP000038 TRANSISTOR 1 E.S.D.
QR1501 DRC3114E0L TRANSISTOR-RESISTOR 1 E.S.D.
QR6001 B1GBCFNL0020 TRANSISTOR-RESISTOR 1 E.S.D.
R1001 ERJ2RHD104X M.RESISTOR CH 1/16W 100K 1
R1002 ERJ2RKD120X M.RESISTOR CH 1/16W 12 1
R1003 J0JHC0000048 FILTER 1
R1051 ERJ2RKD124X M.RESISTOR CH 1/16W 120K 1
R1061 ERJ2RKD244X M.RESISTOR CH 1/16W 240K 1
R1111 D0GA101JA023 CHIP RESISTOR 1
R1504 J0JHC0000048 FILTER 1
R2201 D0GBR00J0004 CHIP RESISTOR 1
R3101 ERJ2GE0R00X M.RESISTOR CH 1/10W 0 1
R3102 ERJ2GEJ222X M.RESISTOR CH 1/16W 2.2K 1
R3108 ERJ2GEJ470X M.RESISTOR CH 1/16W 47 1
R6006 ERJ2RKF5901X M.RESISTOR CH 1/16W 5.9K 1
R6018 ERJ2RKF1183X M.RESISTOR CH 1/16W 118K 1
R6019 ERJ2RHD222X M.RESISTOR CH 1/16W 2.2K 1
R6029 ERJ2RHD561X M.RESISTOR CH 1/16W 560 1
R7009 D1BA1R00A079 CHIP RESISTOR 1
R7030 D0GBR00J0004 CHIP RESISTOR 1
R8002 D0GB104JA065 CHIP RESISTOR 1
R8005 ERJ6GEYJ514V M.RESISTOR CH 1/8W 510K 1
R8006 ERJ6GEYJ514V M.RESISTOR CH 1/8W 510K 1
R8013 ERJ2RHD1621X M.RESISTOR CH 1/16W 1620 1
Ref.
No.
R8032 D1BD4703A119 CHIP RESISTOR 1
R8037 ERJ3GEYJ270V M.RESISTOR CH 1/10W 27 1
R9106 ERJ2GEJ824X M.RESISTOR CH 1/16W 820K 1
RX6001 D1H81034A024 RESISTOR NETWORKS 1
S8001 K0F212A00003 SWITCH 1
S8002 K0D112B00145 SWITCH 1
S8003 K0L1CB000003 SWITCH 1
S8004 K0F111A00541 SWITCH 1
S9501 K0F111A00541 SWITCH 1
S9502 K0F111A00541 SWITCH 1
S9503 K0F111A00541 SWITCH 1
S9504 K0F111A00541 SWITCH 1
S9505 K0F111A00541 SWITCH 1
S9506 K0F111A00541 SWITCH 1
S9507 K0F111A00541 SWITCH 1
S9508 K0F111A00541 SWITCH 1
S9511 K0D112B00145 SWITCH 1
T8001 G5DYA0000135 TRANSFORMER 1
TH3101 D4CC11030013 NTC THERMISTORS 1
VA9021 D4ED18R0A014 VARISTOR 1
VA9022 D4ED18R0A014 VARISTOR 1
X6001 H0J240500068 CRYSTAL OSCILLATOR 1
X9101 H0J327200225 CRYSTAL OSCILLATOR 1
Model No. : DMC-SZ1/SZ02 Frame and Casing Section
Model No. : DMC-SZ1/SZ02 Packing Parts and Accessories Section (1)
Model No. : DMC-SZ1/SZ02 Packing Parts and Accessories Section (2)
Ref.
No.
1 VEP56149A MAIN P.C.B. 1 (RTL), E.S.D.
2 VEP58166B FLASH TOP P.C.B. 1 (RTL), E.S.D.
3 VEP59108A SUB OPERATION P.C.B. 1 (RTL), E.S.D.
4 VYK5M51 FRONT CASE UNIT 1 1P-S
4 VYK5M52 FRONT CASE UNIT 1 1P-K, 02P-K
4 VYK5M54 FRONT CASE UNIT 1 1P-A
4 VYK5M53 FRONT CASE UNIT 1 1P-R
1PC-K,PU-K,EG-K,EP-K,EF-K, EB-K,EE-K, GC
4 VYK5M32 FRONT CASE UNIT 1
-K,GH-K,GF-K, GA-K,GT-K,GK-K,GN-K,GD-K
1PC-A,PU-A,EG-A,EP-A,EF-A, EB-A,GF-A,GA-
A,GK-A,GN-A
1PC-R,PU-R,EG-R,EP-R,EF-R, EB-R,GC-R,GH-
R,GF-R,GA-R, GK-R,GN-R
1PU-S,EG-S,EP-S,EB-S,EE-S, GC-S,GH-S,GF-
S,GA-S,GT-S, GK-S,GN-S
4 VYK5S72 FRONT CASE UNIT 1 (-V)
5 ML-421S/DN BUTTON BATTERY 1 (B9501), [ENERGY]
6 VGK3883 SIDE ORNAMENT(R) 1
7 VGK3853 SIDE ORNAMENT(L) 1
8 VGL1365 AF PANEL LIGHT 1
9 VGQ1C32 PLATE SHEET 1
13 VGQ1D49 FPC TAPE 1
14 VKF5093 JACK DOOR 1
15 VMP0B91 FRAME PLATE 1
16 VYK5M97 LCD UNIT 1
16-1 VYQ7890 LCD PANEL UNIT 1
17 VYK5M22 BATTERY DOOR UNIT 1 (-S)
17 VYK5R08 BATTERY DOOR UNIT 1 (-K)
17 VYK5M24 BATTERY DOOR UNIT 1 (-A)
17 VYK5R26 BATTERY DOOR UNIT 1 (-R)
17 VYK5S70 BATTERY DOOR UNIT 1 (-V)
18 VGU0H52-A BATTERY LOCK KNOB 1
19 VMB4152-A BATTERY LOCK SPRING 1
20 VMB4530 BATTERY OUT SPRING 1
21 VMP0B89 FRAME 1
22 VMP0B92 BATTERY CASE 1
23 VGQ1A46 PCB SPACER 1
24 VGU0L26 MODE KNOB 1 (-S,-A,-R,-V)
24 VGU0L29 MODE KNOB 1 (-K)
25 VYK5M37 REAR CASE UNIT 1 (-S)
25 VYK5M38 REAR CASE UNIT 1 (-K)
25 VYK5M40 REAR CASE UNIT 1 (-A)
25 VYK5M39 REAR CASE UNIT 1 (-R)
25 VYK5S71 REAR CASE UNIT 1 (-V)
25 VYK5U39 REAR CASE UNIT 1 02P-K
25-1 VGL1421 REAR PANEL LIGHT 1
25-2 VGU0K98 CURSOR BUTTON 1
25-3 VGU0K99 MENU/SET BUTTON 1
26 F2A2F8500013 E.CAPACITOR 1 (C8003)
27 L0AA01A00098 SPEAKER 1
28 L0CBAY000141 MICROPHONE UNIT 1
29 VEK0S64 FLASH UNIT 1
30 VGQ1C30 TOP PCB SHEET 1
31 VMB4604 EARTH SPRING 1 (ET8003)
32 VYK5M46 TOP CASE UNIT 1
32-1 VGU0L25 REC BUTTON 1
32-2 VGU0L27 POWER KNOB 1
1P,PC,PU, EG,EP,EF,EB,EE, GH,GF,GA,GT,GK
33 VGQ1D02 DPR SHEET 1
,GN,GD, 02P
100 VXW1432 LENS UNIT (W/O CCD) 1
101 VEK0T14 CCD UNIT 1 E.S.D.
103 VEK0S66 LENS FPC UNIT 1
Ref.
No.
103-1 B3NBA0000011 PHOTO SENSOR 1
104 L6DAYYYD0005 ZOOM MOTOR UNIT 1
105 VMB4603 TILT SPRING 1
106 VMB4603 TILT SPRING 1
107 VXP3818 1ST-3RD LENS FRAME UNIT 1
109 VXP3761 OUTSIDE DIRECT FRAME UNIT 1
114 VDG1781 DRIVE GEAR 1
115 VXQ2221 FIX FRAME UNIT 1
116 VXQ2222 MASTER FLANGE UNIT 1
116-1 L6HAYYYD0047 FOCUS MOTOR UNIT 1
116-2 VMB4593 FOCUS SPRING 1
116-3 VXP3768 4TH LENS FRAME UNIT 1
B1 VHD2004 SCREW 1
B2 VHD2205 SCREW 1
B3 VHD2205 SCREW 1
B4 VHD2205 SCREW 1
B5 VHD2290 SCREW 1
B6 VHD2290 SCREW 1
B10 VHD2409 SCREW 1 (-S)
B10 VHD2408 SCREW 1 (-K,-A,-R,-V)
B11 XQN16+BJ3FN SCREW 1
B12 XQN16+BJ3FN SCREW 1
B101 VHD2388 SCREW 1
200 VPF1372-A CAMERA BAG 1 1EG,EP,EF,EB,EE,GH,GF,GA, GT,GK,GN,GD
201 ----- BATTERY 1 1P,PC,PU, 02P
202 VPF1378 BAG, POLYETHYLENE 1 1P,PC,PU, 02P
203 VFC4297-B HAND STRAP 1 1P,PC,PU, 02P
204 VFF0940-S CD-ROM 1 1P,PC,PU, 02P [SPC] See "Notes"
205 VQT3Z30 BASIC O/I (ENGLISH/SPANISH) 1 1P, 02P
205 VQT3Z31 BASIC O/I (ENGLISH/CANADIAN FRENCH) 1 1PC
205 VQT3Z32 BASIC O/I (SPANISH/PORTUGUESE) 1 1PU
206 VSK0768 AC ADAPTOR 1 1P,PC,PU, 02P
208 VPN7381 PAD 1 1P,PC,PU, 02P
209 VYQ7446 PACKING CASE 1 1P-S
209 VYQ7452 PACKING CASE 1 1P-K,PC-K
209 VYQ7459 PACKING CASE 1 1P-A,PC-A
209 VYQ7464 PACKING CASE 1 1P-R,PC-R
209 VYQ7447 PACKING CASE 1 1PU-S
209 VYQ7453 PACKING CASE 1 1PU-K
209 VYQ7460 PACKING CASE 1 1PU-A
209 VYQ7465 PACKING CASE 1 1PU-R
210 K1HY08YY0026 AV CABLE W/PLUG 1 1P,PC,PU
211 K1HY08YY0025 USB CABLE W/PLUG 1 1P,PC,PU, 02P
212 VQL2C67-1A OPERATING LABEL 1 1PC
300 VPF1372 CAMERA BAG 1 1GC [SPC]
300 VPF1372-A CAMERA BAG 1 1P,PC,PU, 02P
301 ----- BATTERY 1 EXCEPT 1P,PC,PU, 02P
Ref.
No.
302 VPF1378 BAG, POLYETHYLENE 1 EXCEPT 1P,PC,PU, 02P
303 VFC4297-B HAND STRAP 1 EXCEPT 1P,PC,PU, 02P
304 VFF0941-S CD-ROM 1 1EG [SPC] See "Notes"
304 VFF0942-S CD-ROM 1 1EP,EF,EB [SPC] See "Notes"
304 VFF0943-S CD-ROM 1 1EE [SPC] See "Notes"
304 VFF0944-S CD-ROM 1 1GH,GF,GA,GN [SPC] See "Notes"
304 VFF0945-S CD-ROM 1 1GT,GD [SPC] See "Notes"
304 VFF0946-S CD-ROM 1 1GK [SPC] See "Notes"
304 VFF0947-S CD-ROM 1 1GC [SPC] See "Notes"
305 VQT3Z34 BASIC O/I (GERMAN/FRENCH) 1 1EG
305 VQT3Z35 BASIC O/I (ITALIAN/DUTCH) 1 1EG
305 VQT3Z36 BASIC O/I (SPANISH/PORTUGUESE) 1 1EG
305 VQT3Z37 BASIC O/I (TURKISH) 1 1EG
305 VQT3Z38 BASIC O/I (SWEDISH/DANISH) 1 1EP
305 VQT3Z39 BASIC O/I (POLISH/CZECH) 1 1EP
305 VQT3Z40 BASIC O/I (HUNGARIAN/FINNISH) 1 1EP
305 VQT3Z41 BASIC O/I (FRENCH) 1 1EF
305 VQT3Z42 BASIC O/I (ENGLISH) 1 1EB
305 VQT3Z43 BASIC O/I (RUSSIAN/UKRAINIAN) 1 1EE
305 VQT3Z44 BASIC O/I (ENGLISH/CHINESE(TRADITIONAL)) 1 1GH,GF,GA,GC
305 VQT3Z45 BASIC O/I (ARABIC/PERSIAN) 1 1GF,GC
305 VQT3Z46 BASIC O/I (VIETNAMESE) 1 1GA
305 VQT3Z47 BASIC O/I (CHINESE(TRADITIONAL)) 1 1GT
305 VQT3Z48 BASIC O/I (CHINESE(SIMPLIFIED)) 1 1GK
305 VQT3Z49 BASIC O/I (ENGLISH) 1 1GN
305 VQT3Z50 BASIC O/I (KOREAN) 1 1GD
306 VSK0772 AC ADAPTOR 1 1EG,EP,EF,EE,GF,GA
306 VSK0775 AC ADAPTOR 1 1EB,GC,GH
306 VSK0769 AC ADAPTOR 1 1GT
306 VSK0770 AC ADAPTOR 1 1GK
306 VSK0776 AC ADAPTOR 1 1GN
306 VSK0773 AC ADAPTOR 1 1GD
1EG-K,EP-K,EF-K, EB-K, EE-K, GH-K,GA-K,G
309 VYQ7454 PACKING CASE 1
T-K,GN-K,GD-K
1EG-S,EP-S,EB-S,EE-S, GH-S, GA-S,GT-S,GN
309 VYQ7448 PACKING CASE 1
-S
309 VYQ7461 PACKING CASE 1 1EG-A,EP-A,EF-A,EB-A, GA-A, GN-A
309 VYQ7466 PACKING CASE 1 1EG-R,EP-R,EF-R,EB-R,GH-R, GA-R,GN-R
309 VYQ7630 PACKING CASE 1 (-V)
309 VYQ7450 PACKING CASE 1 1GF-S
309 VYQ7457 PACKING CASE 1 1GF-K
309 VYQ7462 PACKING CASE 1 1GF-A
309 VYQ7467 PACKING CASE 1 1GF-R
309 VYQ7451 PACKING CASE 1 1GK-S
309 VYQ7458 PACKING CASE 1 1GK-K
309 VYQ7463 PACKING CASE 1 1GK-A
309 VYQ7468 PACKING CASE 1 1GK-R
309 VYQ7803 PACKING CASE 1 02P-K
309 VPK5305 PACKING CASE 1 1GC-S [SPC]
309 VPK5304 PACKING CASE 1 1GC-K [SPC]
309 VPK5306 PACKING CASE 1 1GC-R [SPC]
310 K1HY08YY0026 AV CABLE W/PLUG 1 1EG,EP,EF,EB,EE,GH,GF,GA, GT,GK,GN,GD
311 K1HY08YY0025 USB CABLE W/PLUG 1 EXCEPT 1P,PC,PU, 02P
312 VQL2C68-1A OPERATING LABEL 1 1GT
314 VQL2J61 GD LABEL 1 1GD-K

DMC SZ1

Uploaded by

Document Informationclick to expand document informationManuale fotocamera

Document Informationclick to expand document information

Copyright:

Available Formats

DMC SZ1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DMC SZ1

Uploaded by

Copyright:

Available Formats

ORDER NO.

© Panasonic Corporation 2012 Unauthorized copy-

1.2. Leakage Current Cold Check

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

3.2. Important Notice

3.2.2. About Flexible Cable and Connector

3.3. General Description About Lead Free Solder (PbF)

3.4. Important Notice 1:(Other than U.S.A. and Canadian Market)

3.5.1. Defining methods:

• Step 3. Turn the Power on:

[CASE 2. Other than “After replacing MAIN P.C.B.”]

• Step 7. Set the model suffix in “INITIAL SETTINGS”:

Selecting the Recording Mode

Slide the REC/PLAY switch to [].

Press /// to select the Recording

List of Recording Modes

Example of Error Code Display

• 4. How to exit from Error Code display mode:

7.3. Service Position

CAUTION-1. (When servicing FLASH TOP P.C.B.)

(Fig. D3) (Fig. D4)

8.3.7. Removal of the Flash Unit and

8.4.1. Removal of the Zoom Motor Unit

8.4.4. 1st-3rd Lens Frame Unit

9.2. Before Disassembling the unit

[ How to Release the camera initial setting ]

Step 1. The temporary cancellation of “INITIAL SETTINGS”:

[ DSC Integrated Assist Software (Method of Using PC) ]

9.2.3. Light Box

9.3.1.1. Startup Electrical Adjustment mode

9.3.1.2. Status Adjustment Flag Setting

4. When the adjustment is completed successfully, adjust-

9.3.1.4. Attention point during Adjustment

9.3.1.5. Finalizing the Adjustment

IC6002 IC1501 BATTERY

TOP OPERATION UNIT

DMC-SZ1/SZ02 OVERALL BLOCK DIAGRAM

CLEN 4 C11 FR CLE

(CROSS KEYIN) PS9001 PP9501

DMC-SZ1/SZ02 SYSTEM CONTROL BLOCK DIAGRAM

SDRAM AREA/1Gbit NAND FLASH ROM AREA/1Gbit

A0D A12D DQ0D DQ31D IO0N IO7N

LCDOUT7 G5 (BUS18 LCDOUT7-0) CS

GPIO13 (CABLE DET)

(USB CAB IN)

PP9001 PS8001 RL8042

DMC-SZ1/SZ02 VIDEO/AUDIO PROCESS BLOCK DIAGRAM

(VH) FP9001 IC3001

V1A FP9001 V1A V1

DMC-SZ1/SZ02 SENSOR BLOCK DIAGRAM

SUB OPERATION P.C.B.

SHUTTER MOTOR SH- RL7004 (SHUTTER A)

PP9001 PS8001 (IGBT VCC)

DMC-SZ1/SZ02 LENS DRIVE BLOCK DIAGRAM

DMC-SZ1/SZ02 POWER BLOCK DIAGRAM

7 STB CHG DET

19 STB CHG OUT 12

Press /// to select the Recording