Unit-IV

LASER PHYSICS

Introduction
The word LASER is an acronym for “Light Amplification by Stimulated
Emission of Radiation”. It is a powerful monochromatic light source of collimated
beam in which the light waves are highly coherent. The laser light has many superior
features compared to conventional light source. Einstein introduced this concept in
1917. Dr. T.H. Maiman demonstrated the first laser namely the ruby laser in the year
1960.

Characteristics of LASER :

Laser differs from the ordinary light with respect to some properties. They are

• Monochromaticity
• Directionality
• Coherence
• Intensity

1. Monochromaticity :
Laser beam is highly monochromatic. It emits single wavelength (one colour)
because atoms or molecules are transition between two energy states. Hence it
possesses good spectra since range of laser beam wavelength () is very narrow. But
ordinary light emits combination of wide range of wavelength (colors) because atoms
or molecules are transition from several number of excited states to ground state, so it
emits different energies, therefore it is polychromatic.

2. Directionality or Divergence :
The light ray coming ordinary light source travels in all directions, but laser
light travels in single direction. For example, the light emitted from torch
spreads 1km distance, But the laser light spreads a few centimeters distance
even it travels longer distance. The ordinary source emits light in all directions
and its angular spread is 1 metre/metre. But the laser is highly directional and non-
divergent and its angular spread is 1mm/metre.
The angular spread () or divergence is given by,
𝑟2 − 𝑟1
𝛷= 𝑑𝑒𝑔𝑟𝑒𝑒
𝐷2 − 𝐷1
where D1, D2 are any two distances from the laser source emitted and r1, r2 are the
radii of the beam spots at a distance D1 and D2, respectively.

3. Coherence
A predictable correlation of the amplitude and phase at any one point with
other point is called coherence. The light from a source consists of wave pattern.
These wave patterns when identical in phase and direction are called coherent.
Laser has a high degree of coherence than the ordinary sources. The coherence of
laser emission results in an extremely high power of 5106 watt/m2. A laser beam
can be focused to a very small area of about 0.7 m diameter.

4. Intensity

Laser light is highly intense than the ordinary light. This is because of
coherence and directionality of laser. The ordinary light spreads in all directions, so
the intensity reaching the target is very less. But in the case of laser, due to high
directionality the intensity of laser beam is concentrated in a small region. This
concentration of energy gives a high intensity. Since in Laser many number of
photons are in phase with each other, the amplitude of the resulting wave
becomes 𝑛𝑎 and hence the intensity of laser is proportional to 𝑛2𝑎2. It is estimated
that light from a typical 1mW laser is 10,000 times brighter than the light from the
sun at the earth’s surface.
Ordinary light versus LASER :

Ordinary light LASER

Ordinary light are Polychromatic Laser light is monochromatic since it
since it consists of radiations of consists of only single wavelength.
several wavelengths.
Ordinary light is divergent because it Laser light is non-divergent because it
spreads in all directions travels in single direction
Intensity of ordinary light is lesser Intensity of Laser light is higher because
because concentration of photons is lesser concentration of photons is higher
Ordinary light is not Coherent Laser light is highly Coherent
Due to less intensity brightness of Due to high intensity brightness of Laser
ordinary light is low light is high
Examples: Sunlight Example: Laser light

Ground state and Excited states:

The lowest energy level for an individual atom occurs when its electrons are
all in the nearest possible orbits to its nucleus ,this energy level is called the “Ground
state”.

When one or more of an atom’s electrons have absorbed energy, they can move
to outer orbits, and the atom is then referred to as being excited, and that energy
level is called as “Excited state.” Excited states are generally not stable; as
electrons drop from higher-energy to lower-energy levels, they emit the extra energy
as light.

Interaction of Radiation with matter

1. Induced Absorption or Stimulated Absorption :

An atom is in the ground state with energy E1 absorbs a photon of energy

h and goes to the excited state with energy E2 as shown in Fig. This transition is
known as stimulated absorption or induced absorption or simply absorption. Here the
energy difference is given as (E2 – E1) = h.
 If there are many number of atoms in the ground state then each atom will absorb
the energy from the incident photon and goes to the excited state then,

The rate of absorption (R12) is proportional to,

R12  Energy density of incident radiation ()

 No. of atoms in the ground state (N1)

R12 = B12  N1

Where, B12 is a constant which gives the probability of absorption transition per
unit time.

2. Spontaneous emission

The natural tendency of an atom is to seek out the lowest energy configuration.
The excited atoms do not stay in the excited state for longer time but tend to return to
the lower state by giving up the excesses energy h as shown in fig. The atom in the
excited state E2 returns to the ground state E1 by emitting a photon of energy h
without any external energy. Such emission of radiation not initiated by any external
influence is called spontaneous emission. This emission is uncontrollable.
 The rate of spontaneous emission R21 (Sp) is proportional to number of atoms or
molecules present in the excited state.

i.e R21 (Sp)  N2

R21 (Sp) = A21 N2

where A21 is a constant which gives the probability of spontaneous emission

transitions per unit time.

3. Stimulated emission

The atom in the excited state E2 as shown in fig. A photon of energy h can
stimulate the atom to move to its ground state. During this process the atom emits
an additional photon whose energy is also h. As the emission is stimulated by
external photon, this process is known as stimulated emission.

The rate of stimulated emission R21 (St) is proportional to,

R21  Energy density of incident radiation ()

 No. of atoms in the excited state (N2)

i.e R21 (St)   N2

R21 (St) = B21  N2

where B21 is a constant which gives the probability of stimulated emission

transitions per unit time.
Einstein’s A and B Coefficient:
(Relation between Einstein’s coefficient and Energy density of radiation)
Einstein’s theory of absorption and emission of light by an atom is based on
Planck’s theory of radiation.

Consider two energy levels E1 and E2 having number of atoms N1 and N2

respectively, as shown in figure.

E2 N2

hυ = E2 - E1

E1 N1

According to Einstein’s theory,

Rate of Stimulated absorption is, R12 = B12  N1
Rate of Spontaneous Emission is, R21(Sp) = A21 N2
Rate of Stimulated Emission is, R21(St) = B21  N2
Where, A and B represents the Spontaneous and Stimulated process
respectively. Eυ is the energy density of radiation.
At thermal equilibrium,

The rate of absorption = The rate of emission

B12  N1 = A21N2 + B21  N2 ---------------- (1)

 [B12 N1 - B21 N2] = A21N2

𝐴21𝑁2
𝐸υ =
[𝐵12 𝑁1 − 𝐵21 𝑁2]

𝐴21
𝐸υ = 𝑁 - ------------ (2)
[𝐵12 1−𝐵21]
𝑁2

Under thermal equilibrium, the population of energy levels obeys the

Boltzmann’s distribution law.
 We know from Boltzmann distribution law,
−𝐸1
𝑁1 = 𝑁0 𝑒 𝐾𝑇
−𝐸2
𝑁2 = 𝑁0 𝑒 𝐾𝑇

Where, K is the Boltzmann constant,

T is the absolute temperature and

N0 is the number of atoms at absolute zero at equilibrium,

we can write the ratio of population as follows,

𝑁1 𝐸2−𝐸1
= 𝑒 𝐾𝑇
𝑁2
since E2 – E1 = h, we have
ℎ𝝊
𝑁1
 =𝑒 𝐾𝑇------------------------------- (3)
𝑁2
Substitute eq(3) in eq(2), we get

𝐴21
𝐸υ = ℎ𝑢
[𝐵12𝑒𝐾𝑇 − 𝐵21]

Divide both numerator and denominator by 𝐵12 , we get

𝐴21
𝐵12 − − − − − − − −(4)
𝐸υ = ℎ𝑢 𝐵21
[𝑒𝐾𝑇 − ]
𝐵12

According to Maxwell-Boltzman statistics

𝐵21
𝐴21 8𝜋ℎ𝑢3 and =1
=
𝐵12 𝑐3 𝐵12

Equation (4) becomes,

8𝜋ℎ𝜐3
𝐸υ = ℎ𝑢
𝑐3 [𝑒𝐾𝑇 − 1]

This is the relation between Einstein’s coefficient and Energy density of

radiations(Eυ).
Difference between Stimulated and Spontaneous Emission :

Sl.No Stimulated Emission Spontaneous Emission

1. An atom in the excited state is The atom in the excited state

induced to return to ground returns to ground state thereby
state, thereby resulting in two emitting a photon, without any
photons of same frequency and external inducement is called
energy is called stimulated spontaneous emission.
emission.

2. The emitted photons move in The emitted photons move in all

same direction and are highly directions and are random.
directional.

3. The radiation is high intense, The radiationis less intense and

monochromatic and coherent. is incoherent.
4. The photons are in phase. The photons are not in phase.

5. The rate of transition is given The rate of transition is given

by R21(St) = B21  N2 by R21(Sp) = A21N2

Light amplification :

Let us consider many numbers of atoms in the excited state. We know the
photons emitted during stimulated emission have same frequency, energy and are in
phase as the incident photon. Thus results in 2 photons of similar properties. These two
photons induce stimulated emission of 2 atoms in excited state thereby resulting in 4
photons. These 4 photons induce 4 more atoms and give rise to 8 photons etc., as
shown in Fig.
 Principle: Due to stimulated emission the photons multiply in each step giving
rise to an intense beam of photons that are coherent and moving in the same direction.
Hence the Light is Amplified by Stimulated Emission of Radiation, termed as LASER.

Population inversion:

When a system is in thermal equilibrium, the distribution of atoms in energy

states at a given temperature follows the Boltzmann’s law as
ℎ𝝊
𝑁1
𝑁2
= 𝑒𝐾𝑇

From the above equation, it is clear that the population is maximum in ground
state as compared with excited state. i.e N1 > N2 .
If the situation is reverse, i.e N2 > N1 , there are more atoms in an excited state than
the ground state as shown in fig(b), this condition is called “Population inversion”.

When a suitable energy is supplied to the system, atoms get excited into 𝐸3.
After their lifetime 10−8 𝑠e𝑐o𝑛𝑑𝑠, the atoms are transit to 𝐸2. Due to more lifetime of
an atom in state 𝐸2(10−3 𝑠e𝑐𝑐o𝑛𝑑𝑠), the atomsstay for longer time than compare
with the state 𝐸3. Due to the accumulation of atomsin 𝐸2, the population inversion is
established in between the 𝐸2 and 𝐸1 states.
 Pumping methods :

The process of achieving population inversion is called pumping. Pumping can be

classified into the following types based on the type of source of pumping.
1. Optical pumping: Here the atoms are excited with the help of photons emitted by
an optical source. The atoms absorb energy from the photons and raises to excited
state. Optical pumping is used in solid laser.
Examples : Ruby Laser, Nd-YAG Laser
2. Electrical pumping: Electrical discharge pumping is used in gas lasers. Since gas
lasers have very narrow absorption. The electrons are accelerated to very high
velocities by strong electric field and they collide with gas atoms and these atoms
are raised to excited state.
Examples : Argon Laser, CO2 Laser, He-Ne Laser

3. Chemical pumping: Due to some chemical reactions, the atoms may be raised to
excited state. Examples : Dye Laser.

Metastable state :
It is an excited state of an atom with a longer life time than the other excited
states. Atoms in the metastable state remain excited for a considerable time in the
order of 10-6 to 10-3 seconds. Such relatively long-lived states are called as Metastable
state. An atom can exist in a metastable energy level for a longer time before
radiating than itcan in an ordinary energy level.
An atom can be excited to a higher level by supplying energy to it. Normally,
excited atoms have short life times and release their energy in a matter of 10-8
seconds through spontaneous emission. It means atoms do not stay long to be
stimulated. As a result, they undergo spontaneous emission and rapidly return to the
ground level; thereby population inversion could not be established. In order to do so,
the excited atoms are required to ‘wait’ at the upper energy level till a large number of
atoms accumulate at that level, that is A Meta stable state.
These levels lie in the forbidden gap of the host crystal. There could be no
population inversion and hence no laser action, if metastable states don’t exist.
 Optical Pumping: Three- and Four-Level Systems
In a simple two-level system, it is not possible to obtain a population inversion
with optical pumping because the system can absorb light (i.e., gain energy) only as
long as population inversion, and thus light amplification, is not achieved.
Essentially, the problem isstimulated emission caused by the pump light itself.
Inversion by optical pumping becomes possible when using a three-level system.
Pump light with a shorter wavelength (higher photon energy) can transfer atoms
from the ground state to the highest level. From there, spontaneous emission or a
non-radiative process (e.g., involving phonons in a laser crystal) transfers atoms to an
intermediate level, called the upper laser level. From that level down to the ground
state, the laser transition with stimulated emission can occur. With sufficiently high
pump intensity, population inversion for the laser transition can be reached as
stimulated emission by the pump radiation is prevented by the transfer to the
intermediate level.
Laser gain with a much lower excitation level is possible in a four-level system,
such as Nd:YAG. Here, the lower level of the laser transition is somewhat above the
ground state, anda rapid (most often non-radiative) transfer from there to the ground
state keeps the population of the lower laser level very small. Therefore, a moderate
population in the third level (the upper laser level), as achieved with a moderate
pump intensity, is sufficient for laser amplification.

Three level four level laser

Components of Lasers
Active Medium:
It is the material in which the laser action takes place. The active medium may be
solid crystals such as liquid dyes, gases like CO2 or Helium-Neon, or semiconductors
such as GaAs. This medium decides the wavelength of laser radiation. Active mediums
contain atoms which can produce more stimulated emission than spontaneous
emission and cause amplification they are called “Active Centers”.
Pumping Energy Source (Excitation Mechanism):
Energy Source (Excitation mechanisms) pumps the active centers from ground state
to excitedstate to achieve population inversion. The pumping by energy source can be
optical, electricalor chemical depending on the active medium.
Resonance Cavity:
The optical resonator contains a pair of reflecting surfaces of which one is fully
reflecting and the other partially reflecting. The active material is kept in between
the two reflecting surfaces. Photons (light) emitted due to transitions between the
energy states of the active material are bounced back and forth between the two
reflecting surfaces, so the intensity of the light is increased. Finally the intense
amplified beam called laser is coming out through the partial mirror as shown in the
diagram.
 Types of Lasers
1. Ruby Laser
The first working laser was built in 1960 by Maiman, using a ruby crytal and so
called the Ruby laser. Ruby belongs to the family of gems consisting of Al 2O3 with
various types of impurities. For example, pink Ruby contains 0.05% Cr atoms. The
schematic diagram of Ruby laser can be drawn as:

Construction of Ruby Laser

The ruby laser consists of a ruby rod. which is made of chromium doped ruby
material. At the opposite ends of this rod there are two silver polished mirrors. Whose
one is fully polished andother is partially polished. A spring is attached to the rod with
fully polished end for adjustment of wave length of the laser light. Around the ruby
rod a flash light is kept for the pump input. The whole assembly is kept in the glass
tube. Around the neck of the glass tube the R.F source and switching control is
designed in order to switch on and off the flash light for desired intervals.

Operation of Ruby Laser:

When we switch on the circuit the R.F operates. As a result, the flash of light is
obtained aroundthe ruby rod this flash causes the electrons within ruby rod to move
from lower energy band towards higher. This flash causes the electrons within ruby
rod to move from lower energy band towards higher energy band. The population
inversion take place at high energy band and electrons starts back to travel towards
the lower energy band. During this movement the electron emits the laser light. This
emitted light travels between the two mirrors where cross reflection takes place of
this light. The stimulated laser light now escapes from partially polished mirror in
shape of laser beam. The switching control of the R.F source is used to switch on and
off the flash light so that excessive heat should not be generated due to very high
frequency of the movement of the electron.

Energy Level Diagram for Ruby Laser

The above three level energy diagram show that in ruby lasers the absorption occurs,
this makes raise the electrons from ground state E1 to the band of level E3 higher
than E1. At E3 these excited levels are highly unstable and so the electrons decays
rapidly to the level of E2. This transition occurs with energy difference (E1 – E2)
given up as heat (radiation less transmission). The level E 2 is very important for
stimulated emission process and is known as Meta stable state. Electrons in this level
have an average life time of about 5ms before they fall to ground state. After this the
population inversion can be established between E2 and E1. The population inversion
is obtained by opticalpumping of the ruby rod with a flash lamp. When the flash lamp
intensity becomes large enough to create population inversion, then stimulated
emission from the Meta stable level to the ground level occurs which result in the
laser output.
Advantages of Ruby Lasers
❖ Beam diameter of the ruby laser is comparatively less than CO2 gas lasers.
❖ Output power of Ruby laser is not as less as in He-Ne gas lasers.
❖ Since the ruby is in solid form therefore there is no chance of wasting material of
 active medium.
❖ Construction and function of ruby laser is self-explanatory.
Disadvantages of Ruby Laser
❖ In ruby lasers no significant stimulated emission occurs, until at least half of the

groundstate
❖ electrons have been excited to the Meta stable state.
❖ Efficiency of ruby laser is comparatively low.
❖ Optical cavity of ruby laser is short as compared to other lasers, which

may beconsidered a disadvantage.

Applications of Ruby Laser

❖ Due to low output power they are class-I lasers and so may used as toys for
children’s.
❖ It can be used in schools, colleges, universities for science programs.
❖ It can be used as decoration piece & artistic display.

2. Helium -Neon (He-Ne) Laser

Construction:
Active medium:
It is a gas laser, which consists of a narrow quartz tube filled with a mixture of
Helium and Neon gases in the ratio 10:1 respectively, at low pressure (~0.1 mm of
Hg). Ne atoms act as active centers and responsible for the laser action, while He
atoms are used to help in the excitation process. The length of the quartz tube is
about 50 cm and the diameter is about 1 cm.
Optical resonator:

To construct the optical resonator cavity, two parallel mirrors are placed at the
ends of the quartz tube one of them is partly transparent while the other is fully
reflecting. The spacing between the mirrors is adjusted such that it should be equal to
the integral multiple of half- wavelengths of the laser light.

Pumping system:
The pumping is done through electrical discharge by using electrodes that are
connected to a high frequency alternating current source.

The common helium-neon gas laser achieves a population inversion in a different

way. A mixture of about 10 parts of Helium and 1 part of Neon at a low pressure is
placed in a glass tube that has parallel mirrors, one of them partly transparent, at both
ends. The spacing of the mirrors is equal to an integral number of half-wavelengths of
the Laser light. An electric discharge is produced in the gas by means of electrodes
outside the tube connected to a source of high-frequency alternating current, and
collisions with electrons from the discharge excite He and Ne atoms to metastable
states respectively above their ground states. Some of the excited He atoms transfer
their energy to ground-state Ne atoms in collisions. The purpose of the He atoms is
thus to help achieve a population inversionin the Ne atoms.
The laser transition in Ne is from the metastable state to an excited state with
the emission of a 650nm of photon. Then another photon is spontaneously emitted in
a transition to a lower metastable state; this transition yields only incoherent light.
 Characteristics of He-Ne Laser
The He-Ne laser is a relatively low power device with an output in the visible red portion of
the spectrum. The most common wavelength produced by He-Ne lasers is 632.8nm. Majority of
He-Ne lasers generate less than 10m watt of power, but some can be obtained commercially with up
to 50m watts of power. For He-Ne lasers the typical laser tube is from 10 to 100 cm in length and
the life time of such a tube can be as high as 20,000 hours.

Applications of He-Ne Laser

The Helium-Neon gas laser is one of the most commonly used Laser today because of the following
applications.

❖ Many schools / colleges / universities use this type of laser in their science programs and
experiments.
❖ He-Ne lasers also used in super market checkout counters to read bar codes and QRcodes.
❖ The He-Ne lasers also used by newspapers for reproducing transmitted photographs.
❖ He-Ne lasers can be use as an alignment tool.
❖ It is also used in Guns for targeting.

Advantages of He-Ne Laser

❖ He-Ne laser has very good coherence property.
❖ He-Ne laser tube has very small length approximately from 10 to 100cm and best lifetime of
20.000 hours.
❖ Cost of He-Ne laser is less from most of other lasers.
❖ Construction of He-Ne laser is also not very complex.
❖ He-Ne laser provide inherent safety due to low power output.

Disadvantages of He-Ne Laser

❖ It is relatively low power device means its output power is low.
❖ He-Ne laser is low gain device.
❖ High voltage requirement can be considered its disadvantage.
❖ Escaping of gas from laser plasma tube is also its disadvantage.
Applications of Lasers

LASER Cutting

Laser is used as a tool to cut thin metal sheets by properly focusing the laser onto any particular
area to be cut, for a longer time. Thus due to thermal effect the sheet is cut.

LASER Welding

In ordinary welding process the heat will be made to fall on the area to be welded, so that the
material in that area will go to molten state. This on cooling will join the material. In this process the
heat will spread all over the surroundings and will affect the other area of the material and hence the
material gets damaged. This damage can be avoided by using laser welding. In laser welding the beam
is focused onto the area to be welded and other areas remain unaffected. Without affecting the material
the area to be welded alone melted and joined.

LASERS in Industry

Using high power lasers we can weld or melt any material. We can produce very small holes that
cannot be done by mechanical drilling. Lasers can be used for cutting and for testing the quality of the
materials. During laser welding and drilling there is no damage the structure of the materials. Lasers
can be used for surface hardening techniques.

MEDICAL APPLICATIONS

Laser cosmetics surgery is used for removing tattoos, scars, stretch marks, sunspots, wrinkles and hairs.

1. Laser types used in dermatology:

It include Ruby (694nm), pulsed diode arrays (810nm), Nd: YAG (1064nm) and Er :
YAG (2940nm)
2. Laser eye surgery:
Laser eye surgery is a medical procedure that uses a laser to reshape a surface of the
eyes. This is done to correct short sightedness, long sightedness and astigmatism (uneven
curvature of the eye surface).
3. Soft- Tissue surgery:
a. In soft tissue laser surgery, a highly focused laser beam vapourises the soft tissue with the
high water content.
 b. Soft tissue laser surgery is used in a variety of applications which include general
surgery, neuro surgery, ENT, dentistry and oral surgery.
c. Soft tissue laser surgery is also used in veterinary surgical fields.
4. Laser light therapy
Laser light therapy involves exposure to laser light of specific variant. The light is
administered for a prescribed amount of light. This is commonly used for skin diseases
and disorders.
5. Laser is widely used for no-touch removal of tumors, especially of the brain and spinal cord
6. In dentistry, laser is used for tooth whitening and carries removal.

LASER SURGERY

A type of surgery that uses the cutting power of a laser beam to make bloodless cuts in tissue or
remove a surface lens such as a skin tumor. There are a number of different types of lasers that differ in
emitted light wavelengths and power ranges and in their ability to clot, cut or vapourise tissue. Among
the commonly used lasers are pulsed dye laser, the YAG laser, the CO2 laser and the argon laser.
 Questions

1. Distinguish between Ordinary light and Laser light.

2. Distinguish between spontaneous and stimulated emission?
3. List out the characteristics of LASER.
4. What is meant by Spontaneous emission?
5. What is meant by stimulated emission?
6. What is meant by population inversion?
7. What is meant by pumping?
8. What are different methods of pumping?
9. What are the conditions required for laser action?
10. What are Einstein‘s coeffecients?
11. Define active medium.
12. What is meant by Optical resonator or Resonance cavity?
13. Explain construction and working of He-Ne Laser.
14. Explain construction and working of Ruby Laser.
15. Derive Einstein’s relation for stimulated emission and hence explain

the existence of stimulated emission.

16. Discuss the applications of laser in various fields.