Suspension KYB AOS Manual Final

2020-21’ KYB AOS Closed Cartridge Fork Service Manual
Fork Disassembly and Assembly including lowering
CONFIDENTIALITY NOTICE 11-2020

This message (including any attachments) contains information that Work must be performed by trained technician.
may be confidential and is for authorized Beta Dealer’s use only. Beta USA, Inc.
Table of Contents
Introduction / Special tools ……………………………………………………..Page 2
Fork Diagram and Component Description..….………………..…..…..Page 3
Cartridge Removal/Disassembly ………………….…………..………….…..Pages 4-8
Fork External Disassembly……………………………………………..…………Pages 9
Cartridge Assembly……………..………………………………...…………….....Page 10-12
Fork External Assembly…………………………..………….……….……………Pages 12-14
Fork Assembly…………………………………………………….………………….…Pages 15-17
Beta KYB AOS Technical Data……..……………………….……………..……..Pages 17
Fork Lowering Procedure…………………..……………..………………………Page 18
* SYMBOL KEY *
☼ Fork spring change ONLY
▼ Fork seal change without complete disassembly
1
Introduction
The procedures in this manual must take place in a clean environment using professional and
some specific tools.
Use caution not to damage the surface of the fork tubes, cartridge, rod, or any other suspension
components.
When using a the bench vise, always use protective jaws made from brass, aluminum or plastic.
Always clean suspension components before assembly, using appropriate solvents and lint free
towels to prevent contamination. Replace common wear parts such as seals, gaskets, bushings
and O-rings every service interval.
CAUTION:
Always wear protective eyewear, gloves and appropriate clothing.

Before you perform any maintenance, be sure to read and carefully follow the detailed
instructions described in this manual.
Incorrect disassembly/assembly of the fork may cause serious damage, injury, or death to the
rider and property.
Special tools
1. Fork inner cap wrench AB-15025

2. 3/8 drive ratchet
3. 8 point fork cap wrench AB-15021
4. 15mm Open end wrench
5. 48mm seal bullet
6. 48mm seal driver
7. Ratio Rite
8. 17mm 3/8 6 pt. socket
9. Synthetic Fork Seal Grease
10. Cartridge rod holding tool
2
Fork Diagram and Component Description
1. Complete Fork Assembly 17. Slide Bushing

2. RH Fork Leg 18. Inner Tube Assembly, Right
3. LH Fork Leg 19. Inner Tube Assembly, Left
4. Steering Stem Nut 20. Axle Carrier Pinch Bolts
5. Top Clamp Stem Bolt 21. Fork Cap O-ring, Big
6. Triple Clamp Bolts 22. Fork Cap O-ring, Small
7. Top Clamp O-ring 23. Free Piston O-rings
8. Top Clamp Assembly 24. Fork Inner Compression Assembly
9. Steering Stem 25. Fork Main spring
10. Outer Tube 26. Rebound Adjuster
11. Outer Tube Wear Ring 27. Cylinder Sub-tank O-Ring
12. Guide Bushing 28. Spring Perch
13. Oil Seal adjuster 29. Oil Lock Collar Cir-clip
14. Oil Seal Housing Cir-clip 30. Cartridge Rod Jam Nut
15. Split Ring Dust Wiper 31. Fork Inner Cartridge Assembly
16. Dust Seal 3
Cartridge Assembly Removal/Disassembly
Secure the outer fork tube with a bench
vice, using soft jaws, a Park tool, or similar.
Use the 8 Point wrench (AB-15021) to loosen the

the outer fork tube. ▼☼
Securely hold the brown anodized outer fork cap

housing with the 8 point wrench. Unscrew the
compression assembly counter-clockwise, using
the inner fork cap tool (AB-15025) from the
outer fork cap.
4
Push down on the outer fork tube to push up the
compression assembly and remove.
Drain oil from both inner and outer

chambers at the same time for complete
service.
Drain the outer fork fluid ONLY, Inner

compression assembly NOT REMOVED ▼☼
Using a 3/8 ratchet with a 17mm socket,

remove the rebound adjuster counter-clockwise
from the lower fork axle lug. ▼☼
5
Compress the inner cartridge assembly exposing
the cartridge rod and insert the holding tool
AB-15027.▼☼
Install a 15mm open end wrench onto the

cartridge rod jam nut and hold securely.
Using a 3/8 ratchet with a 17mm socket,
remove the rebound adjuster counter-
clockwise until removed from the cartridge
rod. ▼☼
.
Compress the inner cartridge assembly

downward to release pressure on the
holding tool and remove it.▼☼
6
Remove the inner cartridge assembly from the
fork external.▼☼
Remove the rebound adjuster push

rod.▼☼
Remove the fork spring from inside the inner fork

tube.▼☼
7
Remove the cartridge rod jam nut from
the cartridge rod.
Wrap Teflon tape around threaded area on the

cartridge rod to prevent seal damage.
Push the cartridge rod completely through the
cartridge cylinder. Be careful to not to damage
the inner cartridge rod seal when removing the
cartridge rod.
Note: For fork lowering, proceed now to page 18.
8
Fork External Disassembly
Using a flathead screwdriver, lightly pry the dust

seal to unseat it from the
outer fork tube.▼
Slide the split-ring dust wiper downward to gain

access to the oil seal circlip. Using a pick,
carefully remove the cir-clip from the cir-clip
groove inside the outer tube. ▼
Use a bench vice to secure the fork lug. Pull

the outer tube off with one firm motion. ▼
Remove the slide bushing, guide bushing,

support washer, back-up ring, oil seal, cir-
clip, split ring wiper and dust seal. Note the
order of removal and orientation.
Clean and inspect all parts, replace all

common wear parts.
9
Cartridge Assembly
Apply synthetic grease to the compression

assembly O-rings.
Submerge the compression piston in fork oil to

cover the piston. This will help with assembly
and remove any trapped air.
Apply Teflon tape to the cartridge rod threads to

help prevent damage to the cartridge rod seal
when re-installing.
Insert the cartridge rod assembly into the

cartridge cylinder assembly.
Using a 10mm T-handle on the rebound

piston nut, push the cartridge rod
assembly through the opposite end of the
cartridge cylinder with a twisting motion.
10
Remove the Teflon tape from the cartridge
rod assembly before installing the jam nut.
Install the cartridge rod jam nut onto the rod

until fully bottomed.
Measure 215cc’s of fork oil and pour it inside

the cartridge assembly.
Raise and lower the cartridge rod in until all air

is bled from the cartridge assembly.
Insert the compression assembly into the

cartridge and tighten.
11
Lay the cartridge assembly diagonal, with one
of the small bleed holes facing downward.
Compress the cartridge rod assembly

completely until it bottoms. Note: a surplus of
oil will come out. If no oil has bled out, you
must repeat the bleeding process due to
insufficient oil during assembly.
The cartridge rod should fully extended by

itself.
Fork External Assembly
Use 600 grit sandpaper with a twisting

motion back and forth to clean up any nick’s,
or burrs on the inner fork tube.▼
Apply synthetic grease to the inside edge of

the new dust seal, including the inner and
outer edge of the new oil seal.
Using a 48mm seal bullet, install the dust
seal, split ring wiper, cir-clip, oil seal, backup
ring, and support washer.
The spring side of the dust seal should face
down and the groove on the oil seal should
face up.▼
12
Remove the seal bullet then install the new
slide and guide bushings. ▼
Install the outer fork tube over the slide

bushing, located on the inner tube.▼
Use the 48mm seal driver against the

support washer to insert the slide bushing
into the outer fork leg. ▼
13
Use the 48mm seal driver to insert the oil seal
and back-up ring into the outer fork leg.▼
Insert the oil seal cir-clip into the outer fork

tube. Confirm the cir-clip is fully seated into
the groove. ▼
Seat the fork dust seal against the outer

tube using the axel lug. Inspect the dust
seal to confirm it is completely seated. ▼
14
Fork Assembly
Install the fork spring. ▼☼
Insert the cartridge assembly into the

external fork leg assembly.▼☼
Compress the cartridge assembly

downward to expose the cartridge rod,
allowing enough room for the cartridge
rod holding tool.
Grease the rebound adjuster push rod

and reinstall inside the cartridge rod.▼☼
15
Completely thread the rebound adjuster onto
the cartridge rod. There should be
approximately 1.5mm between the rebound
adjuster and the jam nut, assuring the
rebound adjuster is completely bottomed.
Secure the jam nut using a 15mm open end

wrench. Using a 3/8 ratchet with a 17mm
socket, torque the rebound adjuster to 29Nm
against the jam nut. ▼☼
Apply synthetic grease to the rebound

adjuster O-ring and threads. Compress the
cylinder assembly downwards to remove the
cartridge rod holding tool and tighten the
rebound adjuster to 50Nm.▼☼
Measure 325cc of Motul 5wt. fork oil

into a ratio-rite. Pour the fork fluid amount
inside the outer fork tube.
Raise the outer fork tube to the cartridge

cylinder assembly. ▼☼
* Standard Travel
Outer Chamber Oil Range: 300-375 cm3
1” Lowering Kit – 325 cm3

2” Lowering Kit – 300 cm3
16
Apply grease to the cylinder O-ring then thread
the cartridge cylinder assembly into the outer
fork tube and tighten.▼☼
Beta KYB AOS Fork Technical Data:

125 200 250/300 RX300 350/350/
390/480
Fork Main Spring Rate .40 kg .41 kg .44 kg .46 kg .47 kg
Fork Spring Length 454 mm 454 mm 454 mm 500 mm 454 mm
Inner Pressure Spring 20Nm 20Nm 20Nm 20Nm 20Nm
Oil Volume (Outer) 320 cm3 340 cm3 330 cm3 325 cm3 320 cm3
1” Lowering Kit 325 cm3 325 cm3 325 cm3 325 cm3 325 cm3
2” Lowering Kit 300 cm3 325 cm3 300 cm3 300 cm3 300 cm3
Oil Volume - Cartridge 215 cm3 215 cm3 215 cm3 215 cm3 215 cm3
Compression Setting 12 out 12 out 12 out 8 out 12 out
Rebound Setting 12 out 12 out 12 out 12 out 12 out
SYMBOL KEY
1” Lowering Kit 2” Lowering Kit
17
Fork Lowering Procedure
1. Follow the fork disassembly procedures on pages 4-8.
2. Install the appropriate fork lowering spacer onto the cartridge rod.
3. Proceed now to pages 10-12; 15-17 .
18

Suspension KYB AOS Manual Final

Uploaded by

Copyright:

Available Formats

Suspension KYB AOS Manual Final

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Suspension KYB AOS Manual Final

Uploaded by

Copyright:

Available Formats

2020-21’ KYB AOS Closed Cartridge Fork Service Manual

Fork Disassembly and Assembly including lowering

CONFIDENTIALITY NOTICE 11-2020

Introduction / Special tools ……………………………………………………..Page 2

Fork Diagram and Component Description..….………………..…..…..Page 3

Cartridge Removal/Disassembly ………………….…………..………….…..Pages 4-8

Fork External Disassembly……………………………………………..…………Pages 9

Cartridge Assembly……………..………………………………...…………….....Page 10-12

Fork External Assembly…………………………..………….……….……………Pages 12-14

Fork Assembly…………………………………………………….………………….…Pages 15-17

Beta KYB AOS Technical Data……..……………………….……………..……..Pages 17

Fork Lowering Procedure…………………..……………..………………………Page 18

☼ Fork spring change ONLY

▼ Fork seal change without complete disassembly

Always wear protective eyewear, gloves and appropriate clothing.

1. Fork inner cap wrench AB-15025

1. Complete Fork Assembly 17. Slide Bushing

Use the 8 Point wrench (AB-15021) to loosen the

Securely hold the brown anodized outer fork cap

Drain oil from both inner and outer

Drain the outer fork fluid ONLY, Inner

Using a 3/8 ratchet with a 17mm socket,

Install a 15mm open end wrench onto the

Compress the inner cartridge assembly

Remove the rebound adjuster push

Remove the fork spring from inside the inner fork

Wrap Teflon tape around threaded area on the

Note: For fork lowering, proceed now to page 18.

Using a flathead screwdriver, lightly pry the dust

Slide the split-ring dust wiper downward to gain

Use a bench vice to secure the fork lug. Pull

Remove the slide bushing, guide bushing,

Clean and inspect all parts, replace all

Apply synthetic grease to the compression

Submerge the compression piston in fork oil to

Apply Teflon tape to the cartridge rod threads to

Insert the cartridge rod assembly into the

Using a 10mm T-handle on the rebound

Install the cartridge rod jam nut onto the rod

Measure 215cc’s of fork oil and pour it inside

Raise and lower the cartridge rod in until all air

Insert the compression assembly into the

Compress the cartridge rod assembly

The cartridge rod should fully extended by

Fork External Assembly

Use 600 grit sandpaper with a twisting

Apply synthetic grease to the inside edge of

Install the outer fork tube over the slide

Use the 48mm seal driver against the

Insert the oil seal cir-clip into the outer fork

Seat the fork dust seal against the outer

Install the fork spring. ▼☼

Insert the cartridge assembly into the

Compress the cartridge assembly

Grease the rebound adjuster push rod

Secure the jam nut using a 15mm open end

Apply synthetic grease to the rebound

Measure 325cc of Motul 5wt. fork oil

Raise the outer fork tube to the cartridge