Fuchs Lubricants Company - RENOLIN FECC 5 SYNTH
Fuchs Lubricants Company - RENOLIN FECC 5 SYNTH
Fuchs Lubricants Company - RENOLIN FECC 5 SYNTH
Other means of identification: For further information, please refer to section 9 of the SDS.
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses: Lubricant
Uses advised against: No uses advised against identified.
E-mail: [email protected]
Telephone: +49 621 3701-1333
Fax: +49 621 3701-7303
2 HAZARDS IDENTIFICATION
The product has been classified and labelled as hazardous according to the legislation in force.
Health Hazards
Acute toxicity (Inhalation - dust and mist) Category 4
Hazard summary
Physical Hazards: No data available.
Health Hazards
Ingestion: If ingested, material may be aspirated into the lungs and cause chemical
pneumonitis. Treat appropriately.
Precautionary Statements
2.3 Other hazards: By handling of mineral oil products and chemical products no particular
hazard is known when normal precautions (item 7) and personal protective
equipment (item 8) are kept.
Unknown toxicity: Due to information available product does not contain any ingredients of
unknown toxicity.
3.2 Mixtures
Classification
Chemical name Identifier Classification
Hydrocarbons, low viscous 68649-11-6 Asp. Tox. 1;H304, Acute Tox. 4;H332
Please note that the mineral oils and petroleum distillates used in our products are severely refined and have a
DMSO extract < 3% as measured by method IP 346 and are not classified as carcinogenic according to Note L
of Annex VI of Regulation EC 1272/2008."
Eye contact: Promptly wash eyes with plenty of water while lifting the eye lids.
Ingestion: Call a physician or poison control center immediately. Rinse mouth. Never
give liquid to an unconscious person. If vomiting occurs, keep head low so
that stomach content doesn't get into the lungs. Do NOT induce vomiting.
4.2 Most important symptoms Symptoms of poisoning may even occur after several hours; therefore
and effects, both acute and medical observation for at least 48 hours after the accident. If ingested,
delayed: material may be aspirated into the lungs and cause chemical pneumonitis.
Treat appropriately.
5.2 Special hazards arising During fire, gases hazardous to health may be formed.
from the substance or
mixture:
Special protective Self-contained breathing apparatus and full protective clothing must be
equipment for fire-fighters: worn in case of fire.
6.1 Personal precautions, Ventilate closed spaces before entering them. See Section 8 of the SDS for
protective equipment and Personal Protective Equipment. Keep upwind. Keep unauthorized
emergency procedures: personnel away. In case of spills, beware of slippery floors and surfaces.
6.2 Environmental Precautions: Prevent from spreading (e.g. by binding or oil barriers). Avoid release to the
environment. Environmental manager must be informed of all major
spillages. Prevent further leakage or spillage if safe to do so. Do not allow
to enter drainage system, surface or ground water.
6.3 Methods and material for Absorb with liquid-binding material (sand, diatomite, acidbinders, universal
containment and cleaning binders, sawdust). Dispose of the material collected according to
up: regulations. Stop the flow of material, if this is without risk.
6.4 Reference to other See Section 8 of the SDS for Personal Protective Equipment. See Section
sections: 7 for information on safe handling See Section 13 for information on
disposal.
Dike for later disposal. Prevent entry into waterways, sewer, basements or
confined areas. Stop the flow of material, if this is without risk.
7.1 Precautions for safe Minimize dust generation and accumulation. Do not eat, drink or smoke
handling: when working with the product. Take usual precautions when handling
mineral oil products or chemical products. Prevent formation of aerosols.
Observe good industrial hygiene practices. Provide adequate ventilation.
7.2 Conditions for safe storage, Store locked up. Do not heat up to temperatures close to the flash point.
including any
incompatibilities:
8.1.Exposure Limits
None of the components have assigned exposure limits.
8.2.Exposure controls
Appropriate engineering Provide adequate ventilation. Ventilation rates should be matched to
controls: conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below
recommended exposure limits. If exposure limits have not been
established, maintain airborne levels to an acceptable level.
General information: Wash hands before breaks and after work. Use personal protective
equipment as required. Personal protection equipment should be chosen
according to the CEN standards and in discussion with the supplier of the
personal protective equipment. The usual precautionary measures should
be adhered to inhandling the chemicals or the mineral oil products.
Eye/face protection: Avoid contact with skin and eyes. Goggles/face shield are recommended. If
risk of splashing, wear safety goggles or face shield.
Skin protection
Hand Protection: Material: Nitrile butyl rubber (NBR).
Min. Breakthrough time: >= 480 min
Recommended thickness of the material: >= 0.38 mm
Other: Do not carry cleaning cloths impregnated with the product in trouser
pockets. Wear suitable protective clothing.
Hygiene measures: Always observe good personal hygiene measures, such as washing after
handling the material and before eating, drinking, and/or smoking. Routinely
wash work clothing to remove contaminants. Discard contaminated
footwear that cannot be cleaned.
10.5 Incompatible Materials: Strong oxidizing substances. Strong acids. Strong bases.
10.6 Hazardous Decomposition Thermal decomposition or combustion may liberate carbon oxides and
Products: other toxic gases or vapors.
11 TOXICOLOGICAL INFORMATION
Acute toxicity
Oral
Product:
Dermal
Product:
Inhalation
Product:
ATEmix: 1.17 mg/l
Dusts, mists and fumes
Specified substance(s)
Hydrocarbons, low LC 50 (Rat, 4 h): 1.17 mg/l
viscous Dusts, mists and fumes
Skin Corrosion/Irritation:
Product: Based on available data, the classification criteria are not met.
Carcinogenicity
Product: Based on available data, the classification criteria are not met.
Reproductive toxicity
Product: Based on available data, the classification criteria are not met.
Aspiration Hazard
Product: May be fatal if swallowed and enters airways.
12 ECOLOGICAL INFORMATION
12.1 Toxicity
Acute toxicity
Product: Based on available data, the classification criteria are not met.
Fish
Specified substance(s)
Hydrocarbons, low LC 50 (Fish, 96 h): > 1,000 mg/l
viscous
Aquatic Invertebrates
Specified substance(s)
Hydrocarbons, low EC 50 (Water Flea, 48 h): > 1,000 mg/l
viscous
Chronic ToxicityProduct: Based on available data, the classification criteria are not met.
Aquatic Invertebrates
Specified substance(s)
Hydrocarbons, low NOEC (Water Flea, 21 d): 125 mg/l
viscous
Biodegradation
Product: Not applicable for mixtures
12.5 Results of PBT and vPvB The product does not contain any substances fulfilling the PBT/vPvB criteria.
assessment:
13 Disposal considerations
Disposal methods: Discharge, treatment, or disposal may be subject to national, state, or local
laws.
14 TRANSPORT INFORMATION
DOT
Not regulated.
IATA
Not regulated.
15 REGULATORY INFORMATION
US Federal Regulations
US State Regulations
Inventory Status
DSL On or in compliance with the inventory
TSCA On or in compliance with the inventory
16 OTHER INFORMATION
Disclaimer: The data contained in this safety data sheet are based on our current
knowledge and experience and are given to the best of our knowledge and
belief. It characterizes the product only with regard to safety requirements for
handling, transport and disposal. The data do not describe the product's
properties (tech. product specification). Neither should any agreed property
nor the suitability of the product for any specific technical application be
deduced from the data contained in this safety data sheet. Modifications on
this document are not allowed. The data are not transferable to other
products. In the case of mixing the product with other products or in the case
of processing, the data in this safety data sheet are not necessarily valid for
the new-made material. It is the responsibility of the recipient of the product to
observe federal, state and local law. Please contact us to obtain up-to-date
safety data sheets. This document was issued electronically and has no
signature.