Highway 2

Highway Engineering
Highway cross section and elements
COMSATS University Islamabad, Abbottabad Campus
Lecturer: Muhammad Atiullah Saif

[email protected]
Office : K-302
1
A cross section is a vertical plane (slice) taken at
right angles to the road control line showing
the various elements that make up the roads
structure.
Diagram
The features of the cross-section of the pavement
influences the
▪life of the pavement
▪the riding comfort and safety
➢Right of way
Right of way (ROW) is the width of land acquired for the road
along its alignment.
To accommodate all the cross-sectional elements of the
highway and may reasonably provide for future development
➢Carriageway
The part of a road used by vehicular traffic
➢ Road margins
The portion of the road beyond the carriageway and
on the roadway can be generally called road margin.
Various elements that form the road margins are
given below:
• Shoulders
• Parking lanes
• Bus bays
• Cycle track
• Footpath
• Guard rails
➢ Shoulders
 along the road edge
 accommodate the stopped vehicles
 serve as an emergency lane for vehicles
 provide lateral support for base and surface courses.
 desirable to have a width of 4.6 m and minimum width of 2.5 m is recommended for
2-lane rural highways.
➢ Parking lanes
 provided in urban lanes for side parking
 Parallel parking is preferred because it is safe for the
vehicles moving on the road.
 minimum of 3.0 m width in the case of parallel
➢ Bus-bays
• Bus bays are provided by recessing the kerbs for bus stops. They
are provided so that they do not obstruct the movement of
vehicles in the carriage way.
• They should be at least 75 meters away from the intersection so
that the traffic near the intersections is not affected by the bus-
bay
➢ Cycle track
• Cycle tracks are provided
in urban areas when the
volume of cycle traffic is
high
• Minimum width of 2 m
required, which may be
Increased by 1 meter for
every additional track.
➢ Footpath
 Exclusive right of way to
pedestrians
 For the safety of the
pedestrians when both
the pedestrian traffic
and vehicular traffic is
high
 Minimum width is 1.5
meter and may be
increased based on the
traffic.
➢ Guard rails
 They are provided at the
edge of the shoulder
usually when the road is
on an embankment.
 They serve to
prevent the vehicles
from running off the
embankment, especially
when the height of the
fill exceeds 3 m
➢ Camber
Camber or cant is the cross slope provided to raise middle of
the road surface in the transverse direction to drain off rain
water from road surface.
objectives of providing camber are:
• Surface protection especially for gravel and bituminous
roads
• Sub-grade protection by proper drainage
• Quick drying of pavement which in turn increases safety
11
➢ Kerbs
Kerbs indicate the boundary between the
carriage way and the shoulder or islands or
footpaths.
12
➢Types of Kerbs
Low or mountable kerbs

•Encourage the traffic to remain in the through
traffic lanes
•Allow the driver to enter the shoulder area with
little difficulty.
Semi-barrier type kerbs
•Pedestrian traffic is high
•Height 15 cm above the pavement edge.
•Prevents encroachment of parking vehicles
Barrier type kerbs
To discourage vehicles from leaving the pavement.
Provided when there is considerable amount of
pedestrian traffic.
Submerged kerbs
•Used in rural roads between the pavement edge
and shoulders.
•Provide lateral confinement and stability to the
pavement.
➢Service roads
•Service roads or frontage roads give
access to access controlled highways
like freeways and expressways.
•They run parallel to the highway and
will be usually isolated by a separator
and access to the highway will be
provided only at selected points.
•These roads are provided to avoid
congestion in the expressways and
also the speed of the traffic in those
lanes is not reduced.
 A highway ramp or slip
road is a short section
of road which allows
vehicles to enter or exit
a controlled –access
highway (freeway or
motorway).

Highway 2

Uploaded by

Copyright:

Available Formats

Highway 2

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Highway 2

Uploaded by

Copyright:

Available Formats

Highway Engineering

Highway cross section and elements

COMSATS University Islamabad, Abbottabad Campus

Lecturer: Muhammad Atiullah Saif

Low or mountable kerbs

You might also like