Scribd
Upload
50 views4 pages

Mks Config EN

Uploaded by

Gerardo Hodel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
50 views4 pages

Mks Config EN

Uploaded by

Gerardo Hodel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

#--------------------------------------------------------------------

######### Printer type setting ##################################

#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)


>cfg_firmware_type:1

#machine setting (Normal:1; Delta:2)


>cfg_machine_type:1

#baud rate (9600:1; 57600:2; 115200:3; 250000:4)


>cfg_baud_rate:4

#multi-language(enable:1, disable:0)
>cfg_multiple_language:1

#languages setting
#(simplified Chinese:1; traditional Chinese:2; English:3; Russian:4; Spanish:5).
This configuration is valid when "cfg_multiple_language" is disabled.
>cfg_language_type:3

#extruder number(one:1; dual:2)


>cfg_sprayer_counter:1

#enable heated bed(yes:1; no: 0)


>cfg_custom_bed_flag:1

#the max target temp of extruder and heated bed


>cfg_max_sprayer_temperature:270
>cfg_max_hotbed_temperature:150

#pause position (-1 is invalid; Z-axis is relative position)


>cfg_XPOS:-1
>cfg_YPOS:-1
>cfg_ZADD:5

#-----------------------------------------------------------------------
######### Advanced Function Option ##################################

#enable UPS?(yes:1; no:0)


>cfg_have_ups_device:0

#enable power detecting module(mks ups:2;mks 220det:1; mks pwc:0)


>cfg_insert_det_module:0

#enable auto off after print finish function (no:0; Yes:1）


>cfg_print_finish_close_Machine:0

#set PB0 signal when use it for sencond nozzle (high level:1; low level:0)
>cfg_PB0_trigger_Level:0

#set PB1 signal (high level:1; low level:0)


>cfg_PB1_trigger_Level:0

#set error range of Z-axis on breakpoints recovery


>cfg_breakpoint_z_error:0.2

#---------------------------------------------------------------------------

######### Filament Change Function ##############################


#the speed to extrude filament(mm/min)
>cfg_filament_load_speed:1200
#the lenght to extrude filament (mm)
>cfg_filament_load_length:200

#the speed to retract filament(mm/min)


>cfg_filament_unload_speed:1200
#the lenght to retract filament(mm)
>cfg_filament_unload_length:200

#It is the minimum temperature for filament change.


It will auto heat up if the current temp doesn't reach the target.
>cfg_filament_load_limit_temperature:200

#The length of Load filament before unloader filament.


>cfg_unload_retract_length:2

#The speed of load filament before unloader filament.


>cfg_unload_retract_speed:1200

#---------------------------------------------------------------------------

############ Leveling Function ########################################

#leveling mode(manual:0; auto:1; conceal leveling button:2)


>cfg_leveling_mode:0

#the command of auto leveling (G29 is available for Marlin.While G32 is for
Repetier and Smoothieware)
>cfg_auto_leveling_cmd:G28;G29;

#the point number of manual leveling:(3,4,5 point available)


>cfg_point_number:4

#the coordinates of 5 point on manual leveling


>cfg_point1:50,50
>cfg_point2:180,50
>cfg_point3:180,180
>cfg_point4:50,180
>cfg_point5:150,150

#the travel speed of leveling(mm/min)


>cfg_leveling_z_speed:1500
>cfg_leveling_xy_speed:3000

#---------------------------------------------------------------------------

############# WIFI Function ##########################################

#wifi model(MKS WIFI TFT:0; MKS HLK-WIFI:1)


>cfg_wifi_type:0

#wifi mode(0:sta;1:ap)
>cfg_wifi_mode:0

#wifi name and password


>cfg_wifi_ap_name:MKS_wifi
>cfg_wifi_key_code:makerbase
#0:disable cloud service 1:enable cloud service
>cfg_cloud_enable:1
#cloud service adress
>cfg_wifi_cloud_host:www.baizhongyun.cn
#cloud service port
>cfg_cloud_port:10086

#Dynamic access IP
>cfg_ip_dhcp_flag:1

#IP/mask/gateway
>cfg_ip_address:192.168.3.100
>cfg_ip_mask:255.255.255.0
>cfg_ip_gate:192.168.3.1

#--------------------------------------------------------------------------------

############## Function Customization #######################################

#user-defined function1 and 2.(display this button . disable: 0; enable: 1)


>cfg_function_btn1_display:1

#command of user-defined function


>function_btn1_cmd:M84;

#set number of "More" button


>moreitem_pic_cnt:0

#edit command for 1~7 "More" button,each command must be separated by semicolon ";"
>moreitem_button1_cmd:G28 X0;

>moreitem_button2_cmd:G28 X0;

>moreitem_button3_cmd:G28 Y0;

>moreitem_button4_cmd:G28 Y0;

>moreitem_button5_cmd:G28 Z0;

>moreitem_button6_cmd:G28 Z0;

>moreitem_button7_cmd:G28;

#how many "More" button display on screen interface


>morefunc_cnt:0

#command setting on button1~5


>morefunc1_cmd:G28;
>morefunc2_cmd:G28;
>morefunc3_cmd:G28;
>morefunc4_cmd:G28;
>morefunc5_cmd:G28;

#---------------------------------------------------------------------------------
##### Display Customization(button and logo customized see User's Manual) #######
#the color of screen background
>cfg_background_color:0x000000

#the color of title text


>cfg_title_color:0xFFFFFF

#the color of temperature,fan,(etc) background


>cfg_state_background_color:0x000000

#the color of temprature,fan,(etc) text


>cfg_state_text_color:0xFFFFFF

#the color of file button


>cfg_filename_background_color:0x000000

#the color of file text


>cfg_filename_color:0xFFFFFF

#the color of background in printing


>cfg_printingstat_word_background_color:0x000000

#the color of text in printing status


>cfg_printingstat_word_color:0xFFFFFF

#3D effects setting (disable: 0; enable: 1)


>cfg_BUTTON_3D_effects:0

#The screen is flipped 180°(0x00: no flip, 0xEE: flip)


>cfg_OVERTURN_180:0x00

#shield the function of detection power (0:no shield ,1:shield)


>cfg_disable_PWR_det:0

#shield the function of detection filament (0:no shield ,1:shield)


>cfg_disable_MT_det:0

#Whether to support the function of dual extruder single nozzle.(0: disable, 1:


enable)
#the extruder number need set to dual.
>cfg_single_nozzle:0

#For the M110 command plus check, the version of Marlin 1.0.2 and below is set to
1, and the other versions are set to 0.
>cfg_M110_add_checkSum:1

#Enable function of display error message. (no:0; Yes:1）


>cfg_display_eeror_message:0

#Enable function of babastep. (no:0; Yes:1）


>cfg_babystep_btn_display:1

#-----------------------------------------------------------------------

You might also like