Company name:

Created by:
Phone:

Date: 08/09/2023
Qty. Description
1 SP 17-5

Note! Product picture may differ from actual product

Product No.: On request

Submersible borehole pump, suitable for pumping clean water. Can be installed vertically or horizontally. All steel
components are made in stainless steel, EN 1.4301 (AISI 304), that ensures high corrosive resistance. This pump
carries drinking water approval.
The pump is fitted with a 5.5 kW MS4000 motor with sand shield, mechanical shaft seal, water-lubricated journal
bearings and a volume compensating diaphragm. The motor is a canned type submersible motor offering good
mechanical stability and high efficiency. Suitable for temperatures up to 40 °C.
The motor is fitted with the Grundfos Tempcon sensor that, by use of powerline communication together with a
MP204 control panel, enables temperature monitoring.
The motor is for direct-on-line starting (DOL).

Further product details

The pump is suitable for applications similar to the following:
- raw-water supply
- irrigation
- groundwater lowering
- pressure boosting
- fountain applications.
Pump
All pump surfaces that are in contact with pumped liquids are made in stainless steel which makes them corrosion-
and wear-resistant. The corrosion diagram below shows the capabilities of the pump and motor in relation to the
temperature in Celsius (y-axis) and the concentration of chloride in ppm (x-axis).

The elastomer parts in the pump are made of NBR (Nitrile-Butadiene Rubber) which ensures good wear resistance
and long service intervals.
In case the pump is used for pumping water with high content of hydrocarbons or solvents, Grundfos offers FKM
rubber parts (Fluorocarbon) which are oil and temperature-resistant up to 90 °C.
The pump is built with octagonal bearings with sand flush channels that minimise wear. As wear of the pump is
inevitable, the pump design allows for easy replacement of all internal wear parts (bearings, impeller, wear rings and
seal rings) to maintain high performance and a long lifetime.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. The suction
interconnector is designed to comply with NEMA standards for motor mounting/dimensions.

Printed from Grundfos Product Centre [2023.35.005] 1/7

 Company name:
Created by:
Phone:

Date: 08/09/2023
Qty. Description
1 Motor
The stator is hermetically encapsulated in stainless steel and the windings are embedded in polymer compound. This
results in high mechanical stability, optimum cooling and reduces the risk of short circuits in the windings.
The shaft seal is a tungsten carbide/ceramic replaceable mechanical shaft seal. The material combination provides
optimum sealing, resistance and long life. Together with the shaft seal housing, the sand shield forms a labyrinth
seal, which during normal operating conditions prevents penetration of sand particles into the shaft seal.
The motor is fitted with the Grundfos Tempcon temperature sensor device that includes a NTC-resistor which senses
the temperature.
The resistor is built-in close to the winding.
The temperature is converted into a high-frequency signal which is sent via the submersible drop cable and which
can be converted into a temperature reading by means of Grundfos MP204.
The MP204 is an electronic motor protection device that also monitors the supply network quality to protect the
submersible motor against supply network disturbances.

Liquid:
Pumped liquid: Water
Liquid temperature range: -15 .. 40 °C
Max liquid t at 0.15 m/sec: 40 °C

Technical:
Pump speed on which pump data are based: 3450 rpm
Rated flow: 20 m³/h
Rated head: 57 m
Shaft seal for motor: HM/CER
Approvals: CE,EAC,UKCA,SEPRO,MOROCCO
Approvals for drinking water: ACS,DM174
Curve tolerance: ISO9906:2012 3B
Motor version: T40
Return valve: YES

Materials:
Pump: Stainless steel
EN 1.4301
AISI 304
Impeller: Stainless steel
EN 1.4301
AISI 304
Motor: Stainless steel
DIN W.-Nr. 1.4301
AISI 304

Installation:
Maximum operating pressure: 60 bar
Maximum outlet pressure: 8.3 bar
Type of connection: NPT(F)
Size of connection: 3 inch
Motor diameter: 4 inch
Minimum borehole diameter: 140 mm

Printed from Grundfos Product Centre [2023.35.005] 2/7

 Company name:
Created by:
Phone:

Date: 08/09/2023
Qty. Description
1 Electrical data:
Motor type: MS4000
Motor flange design: Grundfos
Rated power - P2: 5.5 kW
Mains frequency: 60 Hz
Rated voltage: 3 x 208-220-230 V
Service factor: 1.15
Rated current: 26.1-24.5-23.8 A
Starting current: 510-580-620 %
Cos phi - power factor: 0.87-0.86-0.83
Rated speed: 3440-3470-3480 rpm
Start. method: direct-on-line
Enclosure class (IEC 34-5): IP68
Insulation class (IEC 85): F
Built-in temp. transmitter: yes
Length of cable: 2.5 m
Power cable type: FLAT
Motor No: 79285511
Windings: Enamelled

Others:
Minimum efficiency index, MEI ≥: 0.70
Net weight: 37.7 kg
Gross weight: 42.1 kg
Shipping volume: 0.052 m³
Country of origin: DK
Custom tariff no.: 84137000
Environmental approvals: WEEE

Printed from Grundfos Product Centre [2023.35.005] 3/7

 Company name:
Created by:
Phone:

Date: 08/09/2023
Q SP 17-5, 3*220 V eta
Description Value [m³/h] [%]
General information:
Product name: SP 17-5
Product No: On request
EAN number: On request
Price: SAR 0
Technical: 28
Pump speed on which pump data are 3450 rpm
26 40
based:
Rated flow: 20 m³/h 30
24
50
Rated head: 57 m
22
Stages: 5
Number of reduced-diameter 20 60
NONE
impellers:
18
Shaft seal for motor: HM/CER
Approvals: CE,EAC,UKCA,SEPRO,MOR 16 70
OCCO
14
Approvals for drinking water: ACS,DM174
Curve tolerance: ISO9906:2012 3B 12

Model: B 10 100
Motor version: T40
8 80 m 80
Return valve: YES
Materials: 6 60
Pump: Stainless steel
4 40
Pump: EN 1.4301
Pump: AISI 304 2 20

Impeller: Stainless steel 0 0

Impeller: EN 1.4301 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 P1 [kw]

Impeller: AISI 304 Q = 20.93 m³/h H = 54.98 m

P1 = 5.796 kW Eta pump+motor = 54 %
Motor: Stainless steel 95
Pumped liquid = Water Density = 998.2 kg/m³
677

Motor: DIN W.-Nr. 1.4301

1244

566.5

GN
134

3"NPT

3"NPT
Motor: AISI 304 134 GN
Installation:
Maximum operating pressure: 60 bar
Maximum outlet pressure: 8.3 bar
Type of connection: NPT(F)
566.5

Size of connection: 3 inch

Motor diameter: 4 inch
1244

Minimum borehole diameter: 140 mm

Liquid:
Pumped liquid: Water
Liquid temperature range: -15 .. 40 °C
677

Max liquid t at 0.15 m/sec: 40 °C

Electrical data:
Motor type: MS4000 95

Motor flange design: Grundfos

Rated power - P2: 5.5 kW L1 L2 L3 PE

Mains frequency: 60 Hz
Rated voltage: 3 x 208-220-230 V
Service factor: 1.15
Rated current: 26.1-24.5-23.8 A
Starting current: 510-580-620 %
Cos phi - power factor: 0.87-0.86-0.83
Rated speed: 3440-3470-3480 rpm
Start. method: direct-on-line
Enclosure class (IEC 34-5): IP68 U V W PE

Insulation class (IEC 85): F

Built-in motor protection: NONE
M
Thermal protec: external
Built-in temp. transmitter: yes
3

Printed from Grundfos Product Centre [2023.35.005] 4/7

 Company name:
Created by:
Phone:

Date: 08/09/2023

Description Value
Length of cable: 2.5 m
Power cable type: FLAT
Motor No: 79285511
Windings: Enamelled
Others:
Minimum efficiency index, MEI ≥: 0.70
Net weight: 37.7 kg
Gross weight: 42.1 kg
Shipping volume: 0.052 m³
Country of origin: DK
Custom tariff no.: 84137000
Environmental approvals: WEEE

Printed from Grundfos Product Centre [2023.35.005] 5/7

 Company name:
Created by:
Phone:

Date: 08/09/2023

On request SP 17-5

3"NPT
134 GN
566.5

1244
677

95

Note! All units are in [mm] unless others are stated.

Disclaimer: This simplified dimensional drawing does not show all details.

Printed from Grundfos Product Centre [2023.35.005] 6/7

 Company name:
Created by:
Phone:

Date: 08/09/2023
Installation and Input Sizing Results
Water production, Peak flow and Price
Total water production per year: 58200 m³
Avg. water production per day: 159.6 m³/day
Average water production per watt per day: 17 l/Wp/day

Solar module configuration:

Number of solar modules in series: 8, in parallel: 3
Solar array rated power: 9.36 kW
Solar array rated volts: 327 V
Sun tracking: No (fixed)
Tilt angle: 31 deg.

Typical performance at solar radiation 800 W/m²

Flow: 20.9 m³/h
Total head: 55.0 m

Cables and pipes:

Pump cable length: 55 m
Pump cable size: 10 mm²
Total cable loss: 1.5 %

Material, riser pipe: PEH (Australian)

Pipe size (inner diameter), riser pipe: 63mm Metric PN6.3 (57 mm)

Material, discharge pipe: Galvanized steel

Pipe size (inner diameter), discharge pipe: DN 65 (69 mm)
Pipe length of riser pipe: 45 m
Pipe length of discharge pipe: 4 m
Friction loss, discharge pipe: 0.111 m
Friction losses: 3.983 m

Location: Cairo, Cairo, Egypt

Latitude: 30.0444 DD, Longitude: 31.2357 DD

Pump Curve Dimensional Drawing

Q SP 17-5, 3*220 V eta
[m³/h] [%]
Q = 20.93 m³/h 3"NPT
H = 54.98 m
P1 = 5.796 kW 134 GN
Eta pump+motor = 54 %
Pumped liquid = Water
Density = 998.2 kg/m³

28

26 40

30
24
50
566.5

22

20 60
1244

18

16 70

14

12

10 100

8 80 m 80
677

6 60

4 40

2 20

0 0
95
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 P1 [kw]

Printed from Grundfos Product Centre [2023.35.005] 7/7